Cisco Firewall :: Can't Ping ASA 5510 Inside Interface

Apr 13, 2013

I  ran into a very strange icmp ping issue. The network has been working fine other than the issue listed below, L2L VPN works fine and all three data centers can access each other via L2L VPN.I have three ASA5510. [code]

View 5 Replies


ADVERTISEMENT

Cisco Firewall :: Cannot Ssh Or Ping ASA 5510 From Inside Interface

Apr 4, 2012

The ASA is configured in very simple transparent mode. As desired, traffic can flow in each direction between inside and outside. I can manage the ASA via console and direct connection to the management interface. The problem is that I cannot ping or ssh to the ASA via the inside interface. I need to be able to manage the ASA from any PC on the inside LAN. I suspect I am missing some easy aspect of the configuration but after a lot of hours I'm about at the end of my patience with it. Here is what I believe to be the relevant parts of the config. 
 
ASA Version 8.2(1)
!
firewall transparent
hostname issr1
enable password 2alej83t5cqT0FWd encrypted
passwd 4kleUY438I93.4ljdh encrypted
names

[code]....

View 4 Replies View Related

Cisco VPN :: Can't Ping Inside Interface Of 5510

Sep 19, 2012

I have recently installed an ASA5510 at a site in South Africa to connect via VPN to a site in the UK (ASA5520).  The VPN comes up fine with the 5520 in the UK, however, I can not connect to the inside interface over the VPN, but can access it from the internal LAN.  All other hosts on the LAN are accessible over the VPN.
 
The 5510 also has another VPN to another site in SA and the 2nd site cannot ping the interface either.

View 10 Replies View Related

Cisco Firewall :: New ASA 5505 / Can't Ping Inside Interface

May 10, 2011

I have a new ASA 5505 and all is working fine, I can CLI and ASDM into it, but just can't ping the inside interface, do I need to enable a feature to make this work somehow?

View 1 Replies View Related

Cisco Firewall :: 5505 - Can't Ping ASA Inside Interface

Dec 12, 2011

I have an ASA 5505 that I'm trying to set up a guest network on.  I've configured an interface as a trunk and allowed the 2 vlans but I'm not getting any layer 3 to it.  The switch connected to it is a 3560 and port is configured as a trunk with the same vlans.
 
I can't ping the ASA inside interface but I see its MAC address in the swtich's table.
 
[code]....

View 4 Replies View Related

Cisco Firewall :: ASA5505 Can't Ping New Firewall On Inside Interface

Jul 14, 2011

I've recently upgraded my old firewall from a PIX to an ASA5505 and have been trying to match up the configuration settings to no avail. I have is that I can't ping the new firewall on it's inside interface, despite having "icmp permit any inside" in the running config. Secondly, the server I have on there ("Sar") can't connect out to the internet.I've included the ASA's running config incase anybody can see if something stands out. I have a feeling it's either not letting anything onto the inside interface, or there is no nat going on. Lastly (and possibly relevant), the firewall is actually going at the end of a vlan, which is different to the firewall's inside vlan number. I don't know if this is actually the problem because the server can't connect out even if connected directly into the firewall.

View 32 Replies View Related

Cisco Firewall :: ASA 5505 / Cannot Access Internet Or Ping From Inside Interface?

Jul 26, 2011

I am having a problem configuring my ASA 5505 for NAT.

View 3 Replies View Related

Cisco Firewall :: Unable To Ping Inter Interface (inside To Outside) Of ASA 5520

Jul 26, 2011

I am unable to ping inside interface (Rin) to outside interface (Rout) of my Cisco ASA 5520 runing on ASA Version 8.4(1). 
 
ASA Version 8.4(1)
!
hostname FW5520

[Code].....

View 10 Replies View Related

Cisco Firewall :: Unable To Ping Host From Inside Interface From PIX525

Feb 3, 2012

When I tried to upgrading PIX525  6.3 to  7.0 , Not able to Ping the host from the PIX 525 Inside interface  which is on the same subnet,  Also from the host to Inside Interface ,  Tried with Directly connected  laptop with Cross cable and using Straight cable via switch, But the  results end with fail.

View 2 Replies View Related

Cisco Firewall :: Access And Ping Inside Interface Of ASA5505 From Remote Network?

Sep 13, 2012

I am trying to access and ping the inside interface of a ASA5505 from a remote network.  From the remote network, I am able to access anything on the local network, but the ASA5505 inside interface.The 2 networks linked by a fiber link which have a transport network on another interface.  From the remote network, I am able to ping the transport network interface IP, but I would like to be able to ping the inside interface IP.  When I do a packet tracer, I get a deny from an implicit rule.How can I achieve that?
 
Here are the subnets involved and the ASA5505 config.
 
Remote network : 10.10.2.0/24
Local network : 10.10.1.0/24
Transport network : 10.10.99.0/24

[code]....

View 1 Replies View Related

Cisco Firewall :: ASA 5510 With Inside Interface And DMZ Not Working

Feb 5, 2012

i have here a ASA 5510 sec k9.
 
I build a Config with a DMZ,INSIDE and OUTSIDE Interface. My Plan is to use the IP-Address of the OUTSIDE Interface with PORT to setup a HTTP Server In the DMZ
 
But my Config doesn't work. And I have no Plan why .....
 
The Inside Interface have to work normal. The Traffic to the Internet is TRiggert from Inside with Dynamic PAT
 
ciscoasa(config)# exit 
ciscoasa# show run
: Saved
:
ASA Version 8.4(1)

[Code].....

View 2 Replies View Related

Cisco Firewall :: ASA 5510 Inside Access To NAT IP On Outside Interface

Jun 28, 2012

we have a server that has an outside IP and an inside IP. It's inside ip is 192.168.222.30/24 and it's outside IP is 199.204.50.2/29. The connection to this server from the outside is perfectly fine, but access from inside users to the NAT'd IP which is 199.204.50.2/29 is having issues, however, access to the inside IP works fine (this part makes sense)Will It be a must to set the inside DNS A record to the inside IP and not the outside IP, or can users on the inside interface access the NAT'd IP which is assigned to the server
 
LAN(192.168.222.0/24)<=====>InsideASAOutside<=====>(Server with NAT IP 192.168.222.30/24, it's also physicall assigned to this server).This is an ASA 5510 with 8.4.                  

View 10 Replies View Related

Cisco Firewall :: 2800 Routers / ASA 5510 Cannot Ping Via Route Inside?

Mar 3, 2013

I recently added a business cable modem to relieve some of the congestion I was getting on my T1 for our MPLS network.  There was an ASA 5510 collecting dust in a closet here and I thought it would be the perfect device for firewalling the traffic coming in from the Cable modem, and handling the routing of our internal MPLS traffic as well.  Internet setup was cake.  The test laptop I have using the ASA as it's gateway has great internet service but it cannot ping across either of our MPLS networks.  I have one MPLS with AT&T and one MPLS with EarthLink.  My hope was to use the cable modem as the Default route for all unspecified internet traffic and route our internal MPLS traffic to the cisco 2800 routers that are currently in place for the MPLS.  I can ping across the MPLS when I telnet to the ASA, but I cannot ping across the MPLS from the client that is connected to the ASA.
 
Here's the topology I'm working with
 
Internet
|
Cable Modem
|
ASA 5510 10.52.120.23

[Code].....

View 8 Replies View Related

Cisco Firewall :: ASA 5510 - No Internet Connection On Inside Interface

Jan 3, 2012

so i have a ASA 5510. The ASA is Connect with the Internet through PPOE DSL MODEM
 
The outside Interface get an IP. The Inside Interface get through DHCP from the ASA the Internet DNS SERVER (T-Online) But the HOST do not connect to the Internet because the DNS Server is timed out
 
Code...

View 10 Replies View Related

Cisco Firewall :: 5510 - Duplicate IP Address With ASA Inside Interface

Apr 5, 2012

We've had issues with our Exchange 2010 server (running on ESXi 4.1) since its default gateway was changed to our new ASA 5510.  They manifested as frequent Outlook client connection dropouts or as IP address conflicts whenever Exchange was rebooted.  The temporary fix was to disable the Exchange server NIC, bounce the ASA and enable the server's NIC again.  We saw poor performance from Exchange after a while again, but after some research and testing I realised that disabling proxyarp on the inside interface fixed the problem permanently.
 
However I've now realised that the client VPN no longer routes properly because proxyarp is disabled on the inside interface, so I still have a problem.

View 10 Replies View Related

Cisco Firewall :: 5510 Two Subnet Unable To Talk To Each Other On Same Inside Interface

Mar 8, 2011

I have setup two different subnet 192.168.1.0 and 192.168.2.0 on the same 'inside' interface. They are unable talking to each other. I can ping from firewall to both subnet. Both side unable talking to each other unless I add route on the both side systems.I have added the followings in ASA5510. [code]

View 8 Replies View Related

Cisco Firewall :: 3750 / ASA 5510 - Allow Access To Server On Inside Interface From DMZ?

Feb 28, 2013

My internal network consists of Catalyst 3750 switches segmented into different VLANs.  There is a default route on the layer 3 Catalyst switch sending all unknown traffice to the inside Internet of the ASA 5510.  However, I'd like to have a separate VLAN for wifi guest access and send all of that traffic through one of the DMZ interfaces on the ASA 5510.  I don't think you can have separate default routes based on VLANs on the 3750 switches so my only option is to make the ip address of the DMZ port the default gateway for all hosts on the wifi guest VLAN. 
 
The problem I have is that I have a couple servers behind the inside interface that have services available to the public Internet via a NAT address on the outside interface.  I want the guests on the wifi VLAN to have the ability to access the servers on the inside interface using the public address as well, but have not been able to come up with a solution yet. 
 
Here is my config that pertains to this setup:
 
interface Ethernet0/0description Outside Interfacenameif Outsidesecurity-level 0ip address 76.47.10.x 255.255.255.224 rip send version 1rip receive version 1!interface Ethernet0/1description Inside Interfacenameif Insidesecurity-level 100ip address 192.168.17.1 255.255.255.0 rip send version 1rip receive version 1!interface Ethernet0/3description Wifi Guest Accessnameif DMZ2security-level 50ip address 192.168.60.1 255.255.255.0
 
global (Outside) 1 interface
nat (Inside) 0 access-list nonat
nat (Inside) 1 0.0.0.0 0.0.0.0
nat (DMZ2) 1 0.0.0.0 0.0.0.0
static (Inside,Outside) 76.47.10.x 192.168.17.88 netmask 255.255.255.255
 
I've tried the following commands below but no dice. 

same-security-traffic permit intra-interface
static (inside, inside) 76.47.10.x 192.168.17.88 netmask 255.255.255.255

View 3 Replies View Related

Cisco Switching/Routing :: ASA 5505 Cannot Ping From Inside Interface To Outside Interface

May 1, 2012

I have a Cisco ASA 5505 and I have my internal and external interfaces configured but I currently cannot ping from the inside to an IP Address on the outside.  I had this setup and working and I have another set of equirement that I am replacing that is working with my service provider so I know it is a configuration issue.  When I ping 4.2.2.2 for example I get:
 
Destination host unreachable
 
Do I need to add a static route from my inside interface to my outside interfaces?   

: Saved
:
ASA Version 8.2(5)
!
hostname pxasa

[Code].....

View 2 Replies View Related

Cisco Firewall :: ASA 5510 Unable To Ping From Outside Interface Or Cloud

Nov 27, 2012

One of my client has BSNL leased line with LAN IP POOL we configured those on ASA 5510 nad Internet working fine but from cloud we are not getting any response for ping requiest please find running configuration below:
 
ciscoasa(config)# sh run
: Saved
:
ASA Version 8.2(1)

[Code]....

View 4 Replies View Related

Cisco :: ASA 5510 Ping Between Inside Interfaces

May 4, 2012

I have two inside interfaces (both security level 100) inside and inside110. Inside is 192.168.105.3/24 and inside110 is 192.168.110.3/24. I have a PC on the 192.168.105.0/24 network. I cannot ping the 192.168.110.3 IP of interface inside110.

View 2 Replies View Related

Cisco WAN :: ASA 5510 / Forcing Inside Interface To Go Out Backup ISP?

Nov 12, 2012

We have a 5510 and I have a second ISP setup for a backup link. We have 4 ports connected to 4 different internal subnets. I want to force one of the ports to use the backup ISP link at all times. I'm having a little problem with where I need to make the changes in my ASA.

Interface "outside" is my main ISP
Interface "building3" is my backup ISP.
 
I want to force the "Guest" network to use the "building3" link for all traffic. Here's a snippet of my config
 
global (outside) 10 interface
global (building3) 10 interface
nat (inside) 0 access-list nonat
nat (inside) 10 0.0.0.0 0.0.0.0
nat (Guest) 10 0.0.0.0 0.0.0.0

[URL]
 
Do I need to change the global pool or create a new one? I have a couple free public IP addresess on the building3 subnet I can use for a pool.

View 2 Replies View Related

Cisco Firewall :: PIX 501 / Can Traffic Goes From Inside Interface To Outside Interface

Oct 9, 2011

I have Pix 501 firewall and I'm just configuring the device for "Email Server" to allowing POP/SMTP.
 
Inside Interface Address: 132.147.162.14/255.255.0.0
Outside Interface Address: ISP provided IP address
 
My question is can my traffic goes from inside interface to outside interface? (because the inside interface address not from 10.0/172./192.168 private address)Also I'm allowing internet from this email server (132.147.162.14) so what my access list to be configured? and what my subnet mask shoud be there?
 
Pix(config)#access-list outbound permit tcp 132.147.162.14 255.255.0.0 any eq 80
Pix(config)#access-list outbound permit udp 132.147.162.14 255.255.0.0 any eq 53
Pix(config)#access-group outbound in interface inside

View 7 Replies View Related

Cisco Firewall :: ASA5510 - Unable To Ping From User Desktop To Firewall Inside IP

Jun 11, 2012

I am able to ping from Switch to firewall inside ip and user desktop ip but unable to ping from user desktop to  FW Inside ip.. config is below for both switch and FW Cisco ASA5510....
 
TechCore-SW#ping 172.22.15.10
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.22.15.10, timeout is 2 seconds:

[Code].....

View 7 Replies View Related

Cisco Firewall :: Cannot Ping To Inside Hosts From ASA-8.2

Jun 8, 2013

I am struggling to get successfull pings beween asa and inside hosts but couldn't succeed. Done packet tracer result is acl-drop
 
Here is the running config
 
Prem-ASA(config)# sh run
: Saved
:

[Code].....

View 7 Replies View Related

Cisco Firewall :: ASA5510 Cannot PING From Inside To Outside

Jul 1, 2012

I cannot seem to determine exacly why I am not able to ping from the inside to outside using the standard 100/0 security levels respectively. I am dynamic natting the inside to the outside interface, something I don't usually do but cannot see why ICMP's are not passing through.
 
The Packet trace tool says there is something in the ACL but there really isn't.
 
Is there simply an issue of Natting to the WAN interface on a 5510?

View 10 Replies View Related

Cisco Firewall :: ASA 5505 Ping Inside To Outside Don't Go

Sep 29, 2012

I have 2 ASA and would like to build a Side-to-Side VPN between these ASA. So I can learn something about configure a ASA for different thinks. But now I don`t can Ping from a Client to the Internet-Router.My Configuration is:
 
Client IP 192.168.1.100 <===> ASA Inside 192.168.1.1 /Outside 192.168.178.254 <===> Router 192.168.178.1
 
Is there something wrong at my config? or do I need inside private Adresses and at the Outside Global IP`s.
 
At the Router I have a Static Route that the 192.168.1.0 / 24 ist to find over Gateway 192.168.178.254

View 2 Replies View Related

Cisco Firewall :: Failover ASA 5505 - Setup Second Inside Interface On Firewall?

Feb 19, 2012

I have a Cisco ASA 5505 in our office. We are currently using Interface 0 for outside and 1 for inside. We only have 1 Vlan in our environment. We have two three switches behind the firewall. Today the uplink to Interface 1, to the firewall, on the switch went bad. I want to setup a second inside interface on the firewall and configure it as failover incase this happens again. I want to attach it to the other switch. Can I do this? If so, what do I need to do? would it only be a passive/standby interface?

View 1 Replies View Related

Cisco Firewall :: ASA5505 - Can't Ping Inside Host

Sep 29, 2012

I just try to ping a internal Host but it want to go.
 
Laptop<===>ASA5505
 
Connected is the Laptop at Ethernet 0/2 Inside
 
My running-config is a clear config, only VLAN 1 has a IP and Ethernet 0/2 is up.
 
But If I try to ping to the Laptop I get the followed:
 
asa5505# ping 192.168.1.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.100, timeout is 2 seconds:
?????
Success rate is 0 percent (0/5)
asa5505#
 
From the Laptop to the ASA5505 I can Ping successfully.

View 6 Replies View Related

Cisco Firewall :: ASA5510 - Cannot Ping Inside Over VPN After Upgrade

Jan 16, 2012

We currently have a central hub using an ASA5510 and then a few site-to-site VPN connections to our support staff homes. The devices at the homes are Cisco routers. We were running version 8.25 on the ASA and all was working fine. We recently upgraded to version 8.42 and although all the functionality of the network is ok and it does what it should, our support staff cannot ping, ASDM or telnet to the ASA inside interface anymore whereas they could before the upgrade. The home VPNs all run on a 10.30 subnet (i.e. 10.30.1.x, 10.30.2.x etc etc). I can post our config (security edited of course), but it is quite a big config. The command management-access inside is specified and the 10.30.0.0/16 subnet is permitted to ASDM and Telnet. Are there any extra things that have to be done in version 8.42 to get this to work as the support staff do have to access the firewall for configuration purposes. At the moment, they have to telnet to one of the routers on the local LAN and then Telnet to the firewall from there.Prior to the upgrade, they were all able to ping the inside ASA interface and also telnet and HTTPS to it from their PCs at home. Now they cannot and the only change made was an upgrade to 8.42. Immediately after the upgrade none of them can ping the interface anymore and it seems it can only be accessed from the local LAN. I cannot find any access-lists that might be blocking the packets so can only assume it's something in the way 8.42 works.

View 8 Replies View Related

Cisco Firewall :: PIX 515E Unable To Ping Outside From Inside

Dec 1, 2012

I' d like to have some support for a very-basic PIX firewall configuration. I 'm dealing with  PIX 515E. Inside hosts can ping inside interface , outside hosts outside interface and so on. Simply i cannot ping outside interface from inside hosts, Inside host-192.168.1.0

Outside - any host like google.com, or to check my isp link's dns ip. I have attached the pix configuration text file to test.

View 10 Replies View Related

Cisco Firewall :: Allow Ping From Inside To Outside In 2900 Router?

Apr 7, 2013

I have a Cisco router 2900 with firewall, i need to know how can i allow the ping from self zone to outside zone, i trried to create policy from self to outside but i still didn't allow ping or tracert, i get that message when i try to ping from cisco router: "Unrecognized host or address, or protocol not running"

View 3 Replies View Related

Cisco Firewall :: ASA5505 Cannot Ping Inside Host

Aug 2, 2011

I have Cisco ASA 5505  installed  and use as default gateway. I go to Internet through the ASA5505 Here is my Problem.I can not ping from ASA prompt(ASA#) to my Laptop connected to the ASA, but i can ping the ASA inside interface from laptop i can not use ASDM  and the VPN Tunnel is not working between the sie
  
ASA# ping 10.10.10.12
???????????
100% lost 
Laptop c
C:/ping 10.10.10.1
!!!!!!!!!!!!!!!!
 
Here is the Topology
 
INTERNET .<=========================>ASA<===============================> LAPTOP
  
I disabled window firewall on the Laptop , but no goof result.

View 3 Replies View Related

Cisco Firewall :: ASA 5540 Want To Ping Across Inside To Outside For Testing

Sep 27, 2012

ASA 5540 8.2 (5)I have tried many combinations of command line syntax suggested in this forum but none are providing success so far.
 
I want to ping from the Inside Interface across to the Outside Interface and visa versa.I have tried various ACLs as well as "inspect icmp" in the config, etc still no go.
 
I can ping each interface from the console command line but cannot ping across each interface. [code]

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved