I have a Cisco router 2900 with firewall, i need to know how can i allow the ping from self zone to outside zone, i trried to create policy from self to outside but i still didn't allow ping or tracert, i get that message when i try to ping from cisco router: "Unrecognized host or address, or protocol not running"
View 3 RepliesI am able to ping from Switch to firewall inside ip and user desktop ip but unable to ping from user desktop to FW Inside ip.. config is below for both switch and FW Cisco ASA5510....
TechCore-SW#ping 172.22.15.10
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.22.15.10, timeout is 2 seconds:
[Code].....
I've recently upgraded my old firewall from a PIX to an ASA5505 and have been trying to match up the configuration settings to no avail. I have is that I can't ping the new firewall on it's inside interface, despite having "icmp permit any inside" in the running config. Secondly, the server I have on there ("Sar") can't connect out to the internet.I've included the ASA's running config incase anybody can see if something stands out. I have a feeling it's either not letting anything onto the inside interface, or there is no nat going on. Lastly (and possibly relevant), the firewall is actually going at the end of a vlan, which is different to the firewall's inside vlan number. I don't know if this is actually the problem because the server can't connect out even if connected directly into the firewall.
View 32 Replies View RelatedI am struggling to get successfull pings beween asa and inside hosts but couldn't succeed. Done packet tracer result is acl-drop
Here is the running config
Prem-ASA(config)# sh run
: Saved
:
[Code].....
I cannot seem to determine exacly why I am not able to ping from the inside to outside using the standard 100/0 security levels respectively. I am dynamic natting the inside to the outside interface, something I don't usually do but cannot see why ICMP's are not passing through.
The Packet trace tool says there is something in the ACL but there really isn't.
Is there simply an issue of Natting to the WAN interface on a 5510?
I have 2 ASA and would like to build a Side-to-Side VPN between these ASA. So I can learn something about configure a ASA for different thinks. But now I don`t can Ping from a Client to the Internet-Router.My Configuration is:
Client IP 192.168.1.100 <===> ASA Inside 192.168.1.1 /Outside 192.168.178.254 <===> Router 192.168.178.1
Is there something wrong at my config? or do I need inside private Adresses and at the Outside Global IP`s.
At the Router I have a Static Route that the 192.168.1.0 / 24 ist to find over Gateway 192.168.178.254
I have a new ASA 5505 and all is working fine, I can CLI and ASDM into it, but just can't ping the inside interface, do I need to enable a feature to make this work somehow?
View 1 Replies View RelatedI just try to ping a internal Host but it want to go.
Laptop<===>ASA5505
Connected is the Laptop at Ethernet 0/2 Inside
My running-config is a clear config, only VLAN 1 has a IP and Ethernet 0/2 is up.
But If I try to ping to the Laptop I get the followed:
asa5505# ping 192.168.1.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.100, timeout is 2 seconds:
?????
Success rate is 0 percent (0/5)
asa5505#
From the Laptop to the ASA5505 I can Ping successfully.
We currently have a central hub using an ASA5510 and then a few site-to-site VPN connections to our support staff homes. The devices at the homes are Cisco routers. We were running version 8.25 on the ASA and all was working fine. We recently upgraded to version 8.42 and although all the functionality of the network is ok and it does what it should, our support staff cannot ping, ASDM or telnet to the ASA inside interface anymore whereas they could before the upgrade. The home VPNs all run on a 10.30 subnet (i.e. 10.30.1.x, 10.30.2.x etc etc). I can post our config (security edited of course), but it is quite a big config. The command management-access inside is specified and the 10.30.0.0/16 subnet is permitted to ASDM and Telnet. Are there any extra things that have to be done in version 8.42 to get this to work as the support staff do have to access the firewall for configuration purposes. At the moment, they have to telnet to one of the routers on the local LAN and then Telnet to the firewall from there.Prior to the upgrade, they were all able to ping the inside ASA interface and also telnet and HTTPS to it from their PCs at home. Now they cannot and the only change made was an upgrade to 8.42. Immediately after the upgrade none of them can ping the interface anymore and it seems it can only be accessed from the local LAN. I cannot find any access-lists that might be blocking the packets so can only assume it's something in the way 8.42 works.
View 8 Replies View RelatedI' d like to have some support for a very-basic PIX firewall configuration. I 'm dealing with PIX 515E. Inside hosts can ping inside interface , outside hosts outside interface and so on. Simply i cannot ping outside interface from inside hosts, Inside host-192.168.1.0
Outside - any host like google.com, or to check my isp link's dns ip. I have attached the pix configuration text file to test.
I ran into a very strange icmp ping issue. The network has been working fine other than the issue listed below, L2L VPN works fine and all three data centers can access each other via L2L VPN.I have three ASA5510. [code]
View 5 Replies View RelatedI have Cisco ASA 5505 installed and use as default gateway. I go to Internet through the ASA5505 Here is my Problem.I can not ping from ASA prompt(ASA#) to my Laptop connected to the ASA, but i can ping the ASA inside interface from laptop i can not use ASDM and the VPN Tunnel is not working between the sie
ASA# ping 10.10.10.12
???????????
100% lost
Laptop c
C:/ping 10.10.10.1
!!!!!!!!!!!!!!!!
Here is the Topology
INTERNET .<=========================>ASA<===============================> LAPTOP
I disabled window firewall on the Laptop , but no goof result.
ASA 5540 8.2 (5)I have tried many combinations of command line syntax suggested in this forum but none are providing success so far.
I want to ping from the Inside Interface across to the Outside Interface and visa versa.I have tried various ACLs as well as "inspect icmp" in the config, etc still no go.
I can ping each interface from the console command line but cannot ping across each interface. [code]
I have ASA 5520. I cannot ping the host(192.168.1.20) which is inside firewall from outside hosts. Inside host (192.168.1.20) is translated into (198.24.210.226) using static NAT.From outside host, I used "PING 198.24.210.226". Is it because I used dynamic PAT for inside hosts?
interface GigabitEthernet0/0nameif outsidesecurity-level 0ip address 198.24.210.230 255.255.255.248!interface GigabitEthernet0/1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0
[Code].....
I have an ASA 5505 that I'm trying to set up a guest network on. I've configured an interface as a trunk and allowed the 2 vlans but I'm not getting any layer 3 to it. The switch connected to it is a 3560 and port is configured as a trunk with the same vlans.
I can't ping the ASA inside interface but I see its MAC address in the swtich's table.
[code]....
The ASA is configured in very simple transparent mode. As desired, traffic can flow in each direction between inside and outside. I can manage the ASA via console and direct connection to the management interface. The problem is that I cannot ping or ssh to the ASA via the inside interface. I need to be able to manage the ASA from any PC on the inside LAN. I suspect I am missing some easy aspect of the configuration but after a lot of hours I'm about at the end of my patience with it. Here is what I believe to be the relevant parts of the config.
ASA Version 8.2(1)
!
firewall transparent
hostname issr1
enable password 2alej83t5cqT0FWd encrypted
passwd 4kleUY438I93.4ljdh encrypted
names
[code]....
I have the below configurations done on a 2900 router. [code]I would like to know, if the IP address assigned to dialer1 interface "20.1.2.133" would be listed in "show arp" ?, as it failed to list on our router and I want to know if this is an expected behavior ?
Secondly, does self ping 20.1.2.133 (dialer interface IP) work ? [code]
I am having a problem configuring my ASA 5505 for NAT.
View 3 Replies View RelatedI recently added a business cable modem to relieve some of the congestion I was getting on my T1 for our MPLS network. There was an ASA 5510 collecting dust in a closet here and I thought it would be the perfect device for firewalling the traffic coming in from the Cable modem, and handling the routing of our internal MPLS traffic as well. Internet setup was cake. The test laptop I have using the ASA as it's gateway has great internet service but it cannot ping across either of our MPLS networks. I have one MPLS with AT&T and one MPLS with EarthLink. My hope was to use the cable modem as the Default route for all unspecified internet traffic and route our internal MPLS traffic to the cisco 2800 routers that are currently in place for the MPLS. I can ping across the MPLS when I telnet to the ASA, but I cannot ping across the MPLS from the client that is connected to the ASA.
Here's the topology I'm working with
Internet
|
Cable Modem
|
ASA 5510 10.52.120.23
[Code].....
I am unable to ping inside interface (Rin) to outside interface (Rout) of my Cisco ASA 5520 runing on ASA Version 8.4(1).
ASA Version 8.4(1)
!
hostname FW5520
[Code].....
When I tried to upgrading PIX525 6.3 to 7.0 , Not able to Ping the host from the PIX 525 Inside interface which is on the same subnet, Also from the host to Inside Interface , Tried with Directly connected laptop with Cross cable and using Straight cable via switch, But the results end with fail.
View 2 Replies View RelatedI have 2 questions.Om my cisco 2811 (IOS 12.4(15) T9 IPBASE W/O Crypto) i am using 3 interfaces.And i have a pool of Global addresses: 200.x.z.97-200.x.z.126 255.255.255.0
FastEthernet 0/1 description WAN interfaceip nat outsideip address 200.x.y.253 255.255.255.0
GigabitInterface 0/2/0description DMZ interfaceip nat insideip address 10.0.0.1 255.255.255.0
GigabitInterface 0/3/0description LAN interfaceip nat insideip address 192.168.0.251 255.255.255.0
[Code]....
I am trying to access and ping the inside interface of a ASA5505 from a remote network. From the remote network, I am able to access anything on the local network, but the ASA5505 inside interface.The 2 networks linked by a fiber link which have a transport network on another interface. From the remote network, I am able to ping the transport network interface IP, but I would like to be able to ping the inside interface IP. When I do a packet tracer, I get a deny from an implicit rule.How can I achieve that?
Here are the subnets involved and the ASA5505 config.
Remote network : 10.10.2.0/24
Local network : 10.10.1.0/24
Transport network : 10.10.99.0/24
[code]....
I have a PIX 515E that I want to use to as a border between my internet connection and my Cisco AIR1131AG. I have configured the PIX to have the outside interface as a dhcp client which gets its dynamic IP address from the cable modem. the AP is connected to the E1 inside interface. Now I could see the E1 interface from the arp table from the AP but I cannot ping it. From the firewall I don't see the ARP table from the firewall. and i cannot ping the AP. what is wrong with the configuration? side note, i am able to connect to the AIR1131AG from my laptop I was not able to retrieve an IP address.
FW1 - CONFIGURATION
interface Ethernet0 description uplink towards the techsavvy modem speed 100 nameif outside security-level 0 ip address dhcp setroute !interface Ethernet1 description >>> WIFI LAN ACCESS <<< nameif inside security-level 100 ip address 10.0.0.1 255.255.255.0
[Code].....
how to configure a router 2900 to support connection from 2 firewall ( Active Standby connections) How can i said the router to send the traffic to the stand by when it go down the active Firewall?I was planning to use a Switch ( layer 2 capacity only) in the middle of the equipments ( between the firewalls and the router) in order to send always the traffic for 1 physical interface from the router side , and manage to route all the internatl traffic to the virtual IP of both Firewalls.Also i dont know yet how to configure a VPN site to site if i have that scheme and some Publics NAT ( Firewall - Switch - Router ), i was planning to configure a NAT in the Router in order to allow the VPN traffic to internal IP of the Firewall but still dont know if it will work.
View 2 Replies View Relatedconfigure my Cisco ASA5510 (asa version 8.3.1) so that one of the host (e.g.192.168.8.20) behind management interface can ping to the other host (e.g. 192.168.2.246) behind OUTSIDEinterface. I tried modifying the ACLs, NATs and ICMP statement, but still failed[CODE]
View 19 Replies View RelatedIf there is a router ISRG2 2900 with SEC license and without HSEC license, there is a limit in count of cumulative encrypted VPN tunnels of 225. Which commands can show us a number of current tunnels on the router, so we can see if we are near this limit of 225?
View 4 Replies View RelatedI have two inside interfaces (both security level 100) inside and inside110. Inside is 192.168.105.3/24 and inside110 is 192.168.110.3/24. I have a PC on the 192.168.105.0/24 network. I cannot ping the 192.168.110.3 IP of interface inside110.
View 2 Replies View RelatedI have recently installed an ASA5510 at a site in South Africa to connect via VPN to a site in the UK (ASA5520). The VPN comes up fine with the 5520 in the UK, however, I can not connect to the inside interface over the VPN, but can access it from the internal LAN. All other hosts on the LAN are accessible over the VPN.
The 5510 also has another VPN to another site in SA and the 2nd site cannot ping the interface either.
DNS resolution works and I can surf the web without fail. But if I try to ping any external hosts (I can ping inside interface of ASA fine) from the LAN I get timeouts. I can ping anything from the ASA without fail.
ASA Version 8.4(1)
!
hostname fw1-nat-ann
domain-name inmd.infoblox.com
enable password anWLNen9CTFp7B/X encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
I have configured Remote Access VPN on an ASA5500 Firewall. I am able to login normally and Ping Internal servers on the LAN. However, The servers cannot ping my IP address that i am taking from the RAVPN Pool. So it is a one way communication.
View 2 Replies View RelatedI have easy vpn on my PIX 515e and working normally everywhere, except when my users go FRANCE, the vpn client connect, but, can't ping or access any inside network resources. when same user try any where here in EGYPT, it works normally.
View 2 Replies View RelatedI have an ASA 5505 with the typical inside/outside interfaces. I also have a DMZ that I've named remote for all of my ISP VLAN'd remote offices to connect. I've set the security levels on both the inside and remote interfaces to 100. From remote 192.168.71.0 network I can ping to the remote interface on my ASA, 12.230.129.66/8, but can't ping anything on the inside network, 192.168.1.0, or the web. From my ASA I can ping the router directly attached to the remote interface, 12.233.136.162/8. From my inside 192.168.1.0 network I can hit the web fine, but cant ping the remote router 12.233.136.162 or the remote network..
I dont' know if I missing something with routing, or with the two interfaces w/ same security...or what?
Here's my config. I've also attached an awesomely bad network map.
Result of the command: "wr t"
: Saved:ASA Version 8.2(5) !hostname ciscoasadomain-name wec.wnetenable password 8Ry2YjIyt7RRXU24 encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2switchport access vlan 3!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!interface Vlan1nameif insidesecurity-level 100ip [Code]...