Cisco Switching/Routing :: ASA 5505 Cannot Ping From Inside Interface To Outside Interface
May 1, 2012
I have a Cisco ASA 5505 and I have my internal and external interfaces configured but I currently cannot ping from the inside to an IP Address on the outside. I had this setup and working and I have another set of equirement that I am replacing that is working with my service provider so I know it is a configuration issue. When I ping 4.2.2.2 for example I get:
Destination host unreachable
Do I need to add a static route from my inside interface to my outside interfaces?
: Saved
:
ASA Version 8.2(5)
!
hostname pxasa
[Code].....
View 2 Replies
ADVERTISEMENT
May 10, 2011
I have a new ASA 5505 and all is working fine, I can CLI and ASDM into it, but just can't ping the inside interface, do I need to enable a feature to make this work somehow?
View 1 Replies
View Related
Dec 12, 2011
I have an ASA 5505 that I'm trying to set up a guest network on. I've configured an interface as a trunk and allowed the 2 vlans but I'm not getting any layer 3 to it. The switch connected to it is a 3560 and port is configured as a trunk with the same vlans.
I can't ping the ASA inside interface but I see its MAC address in the swtich's table.
[code]....
View 4 Replies
View Related
Jul 26, 2011
I am having a problem configuring my ASA 5505 for NAT.
View 3 Replies
View Related
Sep 19, 2012
I have recently installed an ASA5510 at a site in South Africa to connect via VPN to a site in the UK (ASA5520). The VPN comes up fine with the 5520 in the UK, however, I can not connect to the inside interface over the VPN, but can access it from the internal LAN. All other hosts on the LAN are accessible over the VPN.
The 5510 also has another VPN to another site in SA and the 2nd site cannot ping the interface either.
View 10 Replies
View Related
Mar 31, 2012
I have a new 3560G to set up a small network for a remote site. I configured the vlan and an SVI as the gateway. The switch is also the DHCP server for the LAN. I configured Gi0/2 as L3 port, connecting to the nearest neighbor. My network runs EIGRP so i advertised the routes into the EIGRP process. The switch forms EIGRP neighbors and learns all routes in the enterprise network. The problems I'm having now are: 1. The switch learns all routes in my enterprise LAN and can ping devices in the enterprise LAN, but I can’t ping any interface on the switch from the enterprise LAN. 2.
View 5 Replies
View Related
Apr 13, 2013
I ran into a very strange icmp ping issue. The network has been working fine other than the issue listed below, L2L VPN works fine and all three data centers can access each other via L2L VPN.I have three ASA5510. [code]
View 5 Replies
View Related
Apr 4, 2012
The ASA is configured in very simple transparent mode. As desired, traffic can flow in each direction between inside and outside. I can manage the ASA via console and direct connection to the management interface. The problem is that I cannot ping or ssh to the ASA via the inside interface. I need to be able to manage the ASA from any PC on the inside LAN. I suspect I am missing some easy aspect of the configuration but after a lot of hours I'm about at the end of my patience with it. Here is what I believe to be the relevant parts of the config.
ASA Version 8.2(1)
!
firewall transparent
hostname issr1
enable password 2alej83t5cqT0FWd encrypted
passwd 4kleUY438I93.4ljdh encrypted
names
[code]....
View 4 Replies
View Related
Aug 23, 2012
How would I go about giving a server on the inside interface of my ASA a public IP address. I have a /28 on the outside interface and I'd like to give a server a public IP and not NAT.
I'd not sure how to go about getting this done.
show run nat=
nat (inside,outside) source static any any destination static NETWORK_OBJ_192.168.0.192_27 NETWORK_OBJ_192.168.0.192_27 no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_192.168.0.0_24 NETWORK_OBJ_192.168.0.0_24 destination static NETWORK_OBJ_192.168.0.192_27 NETWORK_OBJ_192.168.0.192_27 no-proxy-arp route-lookup(code)
View 8 Replies
View Related
Jul 26, 2011
I am unable to ping inside interface (Rin) to outside interface (Rout) of my Cisco ASA 5520 runing on ASA Version 8.4(1).
ASA Version 8.4(1)
!
hostname FW5520
[Code].....
View 10 Replies
View Related
Feb 3, 2012
When I tried to upgrading PIX525 6.3 to 7.0 , Not able to Ping the host from the PIX 525 Inside interface which is on the same subnet, Also from the host to Inside Interface , Tried with Directly connected laptop with Cross cable and using Straight cable via switch, But the results end with fail.
View 2 Replies
View Related
Sep 13, 2012
I am trying to access and ping the inside interface of a ASA5505 from a remote network. From the remote network, I am able to access anything on the local network, but the ASA5505 inside interface.The 2 networks linked by a fiber link which have a transport network on another interface. From the remote network, I am able to ping the transport network interface IP, but I would like to be able to ping the inside interface IP. When I do a packet tracer, I get a deny from an implicit rule.How can I achieve that?
Here are the subnets involved and the ASA5505 config.
Remote network : 10.10.2.0/24
Local network : 10.10.1.0/24
Transport network : 10.10.99.0/24
[code]....
View 1 Replies
View Related
Apr 23, 2012
I am connecting the inside interface to an upstream switch and therefore will need to assign a static IP address to the inside address as I did below:
#sho int ip brief
Vlan1 123.123.123.123 YES manual up up
I will also use this to manage the ASA. I am having a problem with the network configuration of the inside interface as I can't ping the gateway and/or the in IP of the inside interface.Do I need to add any routes?
View 3 Replies
View Related
Jan 21, 2013
Platform:
cisco6509-E with FWSM
Supervisor Engine 32 PISA 8GE
sup-bootdisk:s32p3-adventerprisek9_wan-mz.122-18.ZY2.bin
command:
(config)#ip nat inside source static tcp 10.10.8.147 14029 interface g7/8 14029
(config)#no ip nat inside source static tcp 10.10.8.147 14029 interface g7/8 14029
#clear ip nat tran *
(config)#ip nat inside source static tcp 10.10.8.147 14029 interface g7/8 14029
%Port 14029 is being used by system
Or %Static entry in use, cannot change
But when I perform "sh ip nat tran" command,There is nothing
View 1 Replies
View Related
Jul 21, 2012
We have a Cisco ASA 5505 (v7.2(3)) with a "fairly" normal configuration yet we have a problem where it appears UDP/53 traffic is denied on our inside network.
here is output from our sys log:
SyslogID Source IP Dest IP Description
305006 172.18.22.3 portmap translation creation failed for udp src inside:172.18.22.156/42013 dst inside:172.18.22.3/53
To give some clarification:
172.18.22.3 is one of our DNS servers
172.18.22.156 is a device we're experimenting with.
We've bypassed the Cisco by using a 4G wireless router with this same device - and it works flawlessly.Here is a [scrubbed] copy of our config. It is what I inherited from the previous admin - I'm not sure of all its finer points (I'm not Cisco certified -- perhaps I'm just certifiable.)
: Saved
:
ASA Version 7.2(3)
!
hostname [redacted]
[code].....
View 5 Replies
View Related
Feb 12, 2013
Trying to add inside routes on an ASA 5505 to point traffic to another gateway for other connected networks is resulting in the following error 6Sep 16200 819:13:5810601510.184.236.1265003810.170.54.1823389Deny TCP (no connection) from 10.184.236.126/50038 to 10.170.54.182/3389 flags RST on interface insideI believe the problem is due to the Asymetric tcp connection and the ASA is dropping the connection because it only see one half of the traffic.Is there a way we can stop the firewall dropping the TCP connections on the inside interface? i've tried removing the threat managment which didnt work.Annoying thing is were putting the ASA 5505's in to replace old Watchguard soho firewalls only the watchguards forwarded the traffic no problem at all.
View 1 Replies
View Related
Apr 6, 2011
I have a pair of 5505's in transparent mode and connected them to C2960S. The inside interface (which is VLAN5 on the switchport) keeps dropping, going in to error state. There is no log reference in the switch and the interface shows as UP. The standby ASA has no problem, both interfaces on the switch is up. As soon as I failover the units over, the active node inside interfaces drops.
View 2 Replies
View Related
Oct 9, 2011
I have Pix 501 firewall and I'm just configuring the device for "Email Server" to allowing POP/SMTP.
Inside Interface Address: 132.147.162.14/255.255.0.0
Outside Interface Address: ISP provided IP address
My question is can my traffic goes from inside interface to outside interface? (because the inside interface address not from 10.0/172./192.168 private address)Also I'm allowing internet from this email server (132.147.162.14) so what my access list to be configured? and what my subnet mask shoud be there?
Pix(config)#access-list outbound permit tcp 132.147.162.14 255.255.0.0 any eq 80
Pix(config)#access-list outbound permit udp 132.147.162.14 255.255.0.0 any eq 53
Pix(config)#access-group outbound in interface inside
View 7 Replies
View Related
May 9, 2012
We've just started with the ASA 5505. We do run a DHCP server on the inside interface, so it is in the same VLAN 1 as all of the clients. However, we cannot get it to work.We can't use DHCP Relay, as the ASA 5505 only allows to relay to DHCP servers in a different subnet.Or do we have to move the DHCP server to a different subnet. If so, how would we configure that scenario?
View 13 Replies
View Related
Jan 9, 2013
I just barely put in a Cisco 3925 on our network. I've configured gigabitethernet 0/2 to live on our management VLAN with an IP address of 10.129.0.31/16. I did a "no shut" on the interface. Everything should be ready to allow me to ping and/or SSH to that interface but I can't. It's really weird because I've done this a thousand times (at least on ASAs). I must be missing something. At any rate, the default gateway of the management VLAN is 10.129.0.1. I can ping that from the router. I can also ping that from my laptop (which lives on a completely different VLAN). But I can't ping the router from my laptop or vice versa.
Building configuration...
Current configuration : 1360 bytes
!
! Last configuration change at 19:05:13 UTC Thu Jan 10 2013
!
[Code].....
View 4 Replies
View Related
Aug 9, 2012
I'm trying to set up a Guest VLAN for wireless at a client site, and I feel like I'm missing something small in the configuration, since I can't ping any of the VLAN interfaces from my laptop when the address is statically set to something in the 172.20.100.x range.
I've pasted the configs for the ASA 5505 and the 6 switches below for convenience. Near as I can tell, all should be well. The ports are in trunking mode, the "show cdp neighbors" command returns the proper information, VLAN 100 exists on all the switches, etc.
Code:
ASA Version 7.2(4)
!
hostname ASA
domain-name xxxx.local
enable password Cj3LF.ehxXN3xVkxWcxd encrypted
passwd Cj3LF.ehxXN3xVkWcxd encrypted
[Code] ......
View 17 Replies
View Related
Mar 4, 2013
I'm facing a problem regarding loss of ping packets when i do ping test from nexus3k to another nexus3k connected directly.however there is no error counters on the interfaces on both of devices.the ping failutre is occurring only whenever i do ping test with a large number of ping packets.I don't see the ping loss symptom with default ping test (default ping test is 5 packets).
H/W : N3K-C3548P-10G
S/W : 5.0(3)A1(1)
nexus3k# ping 1.1.1.2
PING 1.1.1.2 (1.1.1.2): 56 data bytes
64 bytes from 1.1.1.2: icmp_seq=0 ttl=254 time=2.732 ms
64 bytes from 1.1.1.2: icmp_seq=0 ttl=254 time=2.732 ms
[code].....
View 2 Replies
View Related
Dec 3, 2011
I've got a 2621 configured as my main gateway to the internet - right now it's obtaining a DHCP ip from a the ISP's proprietary router set to bridged mode.
As of now, I'm unable to ping the internal interface of the router. I can ping external IP's only, even though I have DNS servers listed, i am unable to resolve host names. I'm running a few servers to which people are able to connect to my web server, among other services. I even have a crypto map setup to another 2621 across the country and can ping all internal ips on the other end... I JUST CANNOT PING THE INTERNAL INTERFACE of the router!!
I've noticed that when I ping the router during it's boot process (using linux un-interupted) I get a response in a very short window, then dies again. I'll post my config below:
[code]....
View 9 Replies
View Related
Nov 14, 2011
I have a Cisco ASA 5505, the problem is I am not able to ping to outside natted interface (ip: 172.88.188.123 and 124 and 125) from inside network I have looked for ASA documentation through the internet and still got nothing.
the config are:
: Saved
:
ASA Version 8.2(1)
!
[Code].....
View 2 Replies
View Related
Jul 14, 2011
I've recently upgraded my old firewall from a PIX to an ASA5505 and have been trying to match up the configuration settings to no avail. I have is that I can't ping the new firewall on it's inside interface, despite having "icmp permit any inside" in the running config. Secondly, the server I have on there ("Sar") can't connect out to the internet.I've included the ASA's running config incase anybody can see if something stands out. I have a feeling it's either not letting anything onto the inside interface, or there is no nat going on. Lastly (and possibly relevant), the firewall is actually going at the end of a vlan, which is different to the firewall's inside vlan number. I don't know if this is actually the problem because the server can't connect out even if connected directly into the firewall.
View 32 Replies
View Related
Feb 19, 2012
I have a Cisco ASA 5505 in our office. We are currently using Interface 0 for outside and 1 for inside. We only have 1 Vlan in our environment. We have two three switches behind the firewall. Today the uplink to Interface 1, to the firewall, on the switch went bad. I want to setup a second inside interface on the firewall and configure it as failover incase this happens again. I want to attach it to the other switch. Can I do this? If so, what do I need to do? would it only be a passive/standby interface?
View 1 Replies
View Related
Mar 4, 2011
Is it possible to establish PBR rules that set the ip next-hop to point directly to the inside interface of the ASA5550?Or, do I need to direct this PBR traffic first to a directly connected router interface and then default route to the ASA?At a high level, here's what we have:
ISP 1 - with /21 IP PrefixNo BGP Routing3845 Edge Router - Default Route to ISP 1PIX535 Firewalls (HA) - Default Route to Edge RouterLAN Core/Distribution - Default Route to PIX535 Inside InterfaceAll applications/services use this egress path for PAT/NAT/DMZ/VPN/Etc.
Here's what we are adding:
ISP 2 - with /24 IP PrefixNo BGP Routing3925E Edge Router - Default Route to ISP 2ASA5550 Firewalls (HA) - Default Route to Edge RouterSame connectivity to LAN Core/Distribution
Goals:Maintain ISP 1 for nowMigrate only end user Internet traffic to ISP 2No disruptions to applications/services using current DefGW to PIX535
Question: how to best use PBR to selectively direct traffic to the ASA inside interface?
View 4 Replies
View Related
Sep 25, 2011
I have a PIX-525 with an UR license. I was trying to get my VPN to work from my iphone over the weekend but to no avail. I then changed the interface to the inside to see if my iMac could connect and bingo! It worked. I then tried to connect via inside interface with my iphone and it worked.
I connected a PIX-515e and, using the same settings, can connect to the outside interface via my iPhone.
Now, to answer the pressing questions, yes I changed the server IP address in my IPSEC client settings to reflect the outside and inside interfaces as I was testing each one. I was using a preshared secret. Yes, the secret was entered correctly and they all matched...yes, the tunnel name was entered correctly. I was using local user database for authentication with username/password (i.e. no certificate authorization to make things simpler for debugging). I changed the syslog to debugging and I see absolutely no errors when trying to connect my iphone to the outside interface (i.e. turning wifi off so I'm on my 3G data network). The only thing I see is where my iphone hits the outside interface and it does a teardown (or whatever its called) but that's it.
Why would this work like a charm with my PIX-515e and not my PIX-525? Could the VPN accelerator card in the 525 be at fault? The 515e does not have the aecellerator card. why I can esablish a VPN connection on the inside interface but not the outside?
View 6 Replies
View Related
Sep 29, 2012
I have 2 ASA and would like to build a Side-to-Side VPN between these ASA. So I can learn something about configure a ASA for different thinks. But now I don`t can Ping from a Client to the Internet-Router.My Configuration is:
Client IP 192.168.1.100 <===> ASA Inside 192.168.1.1 /Outside 192.168.178.254 <===> Router 192.168.178.1
Is there something wrong at my config? or do I need inside private Adresses and at the Outside Global IP`s.
At the Router I have a Static Route that the 192.168.1.0 / 24 ist to find over Gateway 192.168.178.254
View 2 Replies
View Related
Jul 8, 2011
I currently have an out of the box ASA5505 and need to change the internal interfact from 192.168.1.1 to 10.20.3.1 so it fits in with the rest of the network.Tried using the ASDM Startup wizard (via 192.168.1.1) and it just seems to hang on "delivering the commands to the device".
View 16 Replies
View Related
Jan 17, 2013
I am trying to upgrade a Cisco ASA over an IPSEC VPN tunnel. My FTP server is on the remote side of the VPN tunnel but I am initiating connections from the inside interface of the firewall. I am currently managing the Firewall over the VPN via it's inside interface (using the management-access inside) command. When I try and update via FTP, the connection is going straight out the outside interface (and not across the VPN tunnel) I have tried upgrading via TFTP but it keeps stopping randomly with (unspecified error) I normally upgrade via FTP though but it's not working in this instance. Essentially what I am asking, is is there an equivalent command for FTP that there is for TFTP: tftp-server interface ip anyconnect I need the connections to originate from the inside interface so they traverse the VPN. I am running 7.2.3?
View 2 Replies
View Related
Aug 18, 2011
We currently have a setup where users connect to the inside of a firewall using the ipsec client. We are moving them to the anyconnect client but are unable to get it to work, we cannot even get a webvpn page on the inside.
When trying to connect with anyconnect the ASA reports an IKE initiator fail on the inside. and no tcp connection flag. We cannot get any response with Webvpn either I have tried using a different tcp port on webvpn but then the asa denies the traffic even though there are no rules denying.
View 3 Replies
View Related
Jun 7, 2013
I have a Cisco 5512 x Firewall connected with Cisco Layer 3 switch 3750.I have two different WAN connections, one for Data and one for voice. Cisco Layer 3 switch is configured with 2 different VLAN's one for data & other is Voice Vlan. Switch is providing DHCP to computers and IP phones. Voice Pool 192.168.10.0/24 Vlan10 and Data pool 192.168.20.0/24 Vlan20.I need to route my data & voice traffic separately. Cisco ASA is connected with two different ISP's. So, how can I do this configuration so that Voice and Data traffic will route separately.
View 7 Replies
View Related
