Cisco Switching/Routing :: Ping Loss On Nexus 3k But No Error Under Interface?
Mar 4, 2013
I'm facing a problem regarding loss of ping packets when i do ping test from nexus3k to another nexus3k connected directly.however there is no error counters on the interfaces on both of devices.the ping failutre is occurring only whenever i do ping test with a large number of ping packets.I don't see the ping loss symptom with default ping test (default ping test is 5 packets).
H/W : N3K-C3548P-10G
S/W : 5.0(3)A1(1)
nexus3k# ping 1.1.1.2
PING 1.1.1.2 (1.1.1.2): 56 data bytes
64 bytes from 1.1.1.2: icmp_seq=0 ttl=254 time=2.732 ms
64 bytes from 1.1.1.2: icmp_seq=0 ttl=254 time=2.732 ms
[code].....
View 2 Replies
ADVERTISEMENT
Nov 21, 2011
I am pinging a host from Nexus 7K. I'm losing every 200th packet when I'm pinging the end host. I don't see any issue with network connection.
View 2 Replies
View Related
Nov 2, 2011
In my network i have Cisco nexus 4 switches those are running as redundancy and fault tolerance. I have mulitple VRF instances are running, when i tried to ping the gateway IP (hsrp Virtual IP) witch same VRF instance it is getting packet loss.
View 3 Replies
View Related
Mar 31, 2012
I have a new 3560G to set up a small network for a remote site. I configured the vlan and an SVI as the gateway. The switch is also the DHCP server for the LAN. I configured Gi0/2 as L3 port, connecting to the nearest neighbor. My network runs EIGRP so i advertised the routes into the EIGRP process. The switch forms EIGRP neighbors and learns all routes in the enterprise network. The problems I'm having now are: 1. The switch learns all routes in my enterprise LAN and can ping devices in the enterprise LAN, but I can’t ping any interface on the switch from the enterprise LAN. 2.
View 5 Replies
View Related
May 1, 2012
I have a Cisco ASA 5505 and I have my internal and external interfaces configured but I currently cannot ping from the inside to an IP Address on the outside. I had this setup and working and I have another set of equirement that I am replacing that is working with my service provider so I know it is a configuration issue. When I ping 4.2.2.2 for example I get:
Destination host unreachable
Do I need to add a static route from my inside interface to my outside interfaces?
: Saved
:
ASA Version 8.2(5)
!
hostname pxasa
[Code].....
View 2 Replies
View Related
Sep 4, 2012
I encountered problem while trying to copy file from Nexus 5548 to my ftp server (proteus - 192.168.12.220 - the Nexus switch is able to resolve name proteus correctly to 192.168.12.220). See below the working and not working scenarios. I have serached through Cisco Bug Database but unable to find any related bug associated to this problem. This Nexus is running the following NX-OS version.
n5000-uk9-kickstart.5.1.3.N1.1a.bin
n5000-uk9.5.1.3.N1.1a.bin
Working (without specifying the username and full path)
[Code].....
View 1 Replies
View Related
May 27, 2013
I have in logs following error message:
%DEVICE_TEST-2-PWR_MGMT_BUS_FAIL: Module 1
Has failed test SpineControlBus 20 times on device Power Mgmt Bus on slot 10 due to error Spine control test failed error number 0x00000002.
View 3 Replies
View Related
Jan 30, 2012
How to write ping tcl script on nexus 7000?
View 5 Replies
View Related
Jul 10, 2012
Yesterday I configured the 7010 Nexus switch. I created a VDC and allocated few ports and configured VLAN for testing. After enabling feature interface-vlan i was allowed to configured L3 interface for the vlan. I assigned ip address and connected few server to check the reachability but it says Destination Host Unreachable.
NX OS Ver : n7000-s1-dk9.5.2.4.bin
Configuration of the VDC below.
feature telnet
feature udld
feature interface-vlan
feature lacp
[Code]....
View 2 Replies
View Related
Feb 26, 2012
I am at a client that I upgrade from running a single 4507 to two Nexus 5548UP switches with two Nexus 2224 fex's connected. The other access layer switches are 2960S switches. I implemented hsrp on the nexus 5k's for redudancy. The issue they are having is that some networks cannot communicate with each other. All user vlans can communicate with the server vlan, but it is not running hsrp on the vlan interface (there is a reason for that, but it not relavent for this issue). The phone vlan, which is running hsrp, can communicate with all networks.
When I am connected to either 5k, they can communicate with all devices on all networks. However, I am on vlan 10, which is a user vlan. I can communicate fine with the server vlan (vlan 101 - not running hsrp) and the phone vlan (vlan 60 - running hsrp). I cannot communicate with vlan 30 or 40, which are both running hsrp. This makes absolutely no sense at all to me. I checked out trunk ports to be sure that vlans are allowed across the networks as well. There are no firewalls between the vlans or ACL's.
View 1 Replies
View Related
Jan 11, 2013
how do we configure sub interface for nexus 7k?do we have to issue ma-address command under physical interface and than configure subinterface? if yes than what do we have to type the mac address for "mac-address" command?I can doing and than configure subinterface but the interface/subinterface didn't come up. do we have to bounce it couple times to bringe it up?
View 1 Replies
View Related
Jun 18, 2012
I want to bring up 40G interface between two nexus 3064 over the fiber but it's not coming up. Have configured the switch for 48*10G and 4*40G. I'm using QSFP on both the switches, OM3 straight fiber cable with MPO connector. The interfaces are not coming up. Notably, it comes up with Coax 3M cable. So it's fine with coax but not with fiber.
View 2 Replies
View Related
Nov 21, 2012
We are getting some error logs on Nexus VDC,as follows:2012 Nov 23 08:49:11 N7K_B-Network_Center_B %$ VDC-3 %$ last message repeated 6 times 2012 Nov 23 08:50:21 N7K_B-Network_Center_B %$ VDC-3 %$ last message repeated 7 times 2012 Nov 23 08:49:11 N7K_B-Network_Center_B %$ VDC-3 %$ last message repeated 6 times2012 Nov 23 08:50:21 N7K_B-Network_Center_B %$ VDC-3 %$ last message repeated 7 times.
View 1 Replies
View Related
Oct 19, 2012
We inserted GLC-T modules and on Nexus 5548 they are showing SFP validation Failed , as per Cisco doc GLC-T is support . Since we have 28 such modules and all after inserting showing same error. please see the below details. I also try configuring speed and inserting modules but no result ..let me know whether my GLC-T module is supported on Nexus 5548
INMUMFDS1SWCORE01# show module
Mod Ports Module-Type Model Status
--- ----- -------------------------------- ---------------------- ------------
1 32 O2 32X10GE/Modular Supervisor N5K-C5548P-SUP active *
2 16 O2 16X10GE Ethernet Module N55-M16P ok
3 0 O2 Daughter Card with L3 ASIC N55-D160L3 ok
[code]
View 6 Replies
View Related
Aug 28, 2012
I have 2 datacenters running same equipement (two Nexu 5596 with FEX).I just took a look at the log just to see if everything is ok and I saw that I have the same error message (a lot of times) at both location :
%SYSMGR-FEX100-5-HEARTBEAT_LOSS: Service "satctrl" heartbeat loss 2 ,max 7,I though it was a problem with my peerklink-keepalive connection but I see the word FEX ....so i'm not sure...
Note that at both locations, my Nexus are connected back to back through the management port using transceivers. So it's a copper cable from the first nexus, going into a transceiver, going to another transceiver in fiber and then back to copper to the other nexus.
View 2 Replies
View Related
Jan 27, 2013
We have purchased two new Nexus 3548 switches. According to documenation the Nexus 3K does support vPC. When trying to enable the feature I get this:
nexus(config)# feature vpc
Error: vPC feature is not supported
nexus(config)#
We are running software version version 5.0(3)A1(1) and it looks like the latest version is 5.0(3)A1(2) so that's not much of a difference.Am I missing something here?
View 4 Replies
View Related
Dec 8, 2012
regarding to the out of band Management interface , if I configured an intervace vlan to be as a managment interface for one vdc ( the default vdc ), when I connected to this vdc via telnet , can I switch to any other vdc ? ( suppose that I have the Admin role which allows me to enter and config all the vdc's )If that is possible so that I dont have to make a dedicated managment ip for each VDC I need to do that only if I want to make vdc admin's account to allow some users to access specific vlans only , is that true ?
View 2 Replies
View Related
Apr 21, 2013
How separate is the management interface on a Nexus 5548?
In context - what's the risk of having a layer 2 only Nx5K in a DMZ and running the managment ports down into an internal managment VLAN, to form peer-keepalive links and software upgrades.
View 4 Replies
View Related
Apr 28, 2013
We have a couple of Nexus 7010's split into Core and Distribution VDCs. MGMT0 interfaces on each of the Nexus VDC's (including the Admin VDC) are configured with different IP address, but on the same subnet i.e 10.10.10.1/24 for admin, 10.10.10.2/24 for Core and 10.10.10.3/24 for Distribution. The MGMT 0 physical port on each Nexus is connected to a physical gig port on a 3750 X switch, and the 3750X has uplinks back to the Nexus configured for vPC.
When i ssh to the VDC MGMT0 IPs from the 3750X, i can access each of these VDCs without any problems. But if i enable routing on each of these links(OSPF) and advertise it to the WAN, i cannot see these routes advertised and also cannot see any of these routes in the local routing table.Just wondering if i have to enable these links on a VLAN and then advertise it to the WAN..But if this the case, VLANs cannot be created on the Admin(default VDC).
View 9 Replies
View Related
Oct 29, 2012
We are getting some error logs on Nexus switch 7K.
Loggs:
----------
2012 Oct 30 22:36:07 SWITCH %CMPPROXY-STANDBY-2-LOG_CMP_UP: Connectivity Management processor(on module 6) is now UP
2012 Oct 30 22:36:40 SWITCH %SYSMGR-2-GSYNC_SNAPSHOT_SRVFAILED: Service "ipqosmgr" on active supervisor failed to sto
re its snapshot (error-id 0x40480005).
2012 Oct 30 22:36:40 SWITCH %SYSMGR-2-STANDBY_BOOT_FAILED: Standby supervisor failed to boot up.
2012 Oct 30 22:36:42 SWITCH %PLATFORM-2-MOD_REMOVE: Module 6 removed (Serial number JAF1550ATBR)
2012 Oct 30 22:42:08 SWITCH %BOOTVAR-5-NEIGHBOR_UPDATE_AUTOCOPY: auto-copy supported by neighbor supervisor, starting
[code]....
View 8 Replies
View Related
Dec 10, 2012
I have Nexus 7K installations in 2 locations. Both of them have multiple VDCs. In default VDC there are continous tacacs error message though tacacs is not configured. The requests are from various public IPs where thsi VDC is not exposed to Internet at all. What would be t he cause of it?
%AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication failed for user root from 195.2.219.2
2012 Dec 11 16:25:28 IDC-FBDTB-AMR2-CN7K-01 %AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication failed for user nagios from 67.78.206.226
- sshd[25797]
2012 Dec 11 16:25:34 IDC-FBDTB-AMR2-CN7K-01 %AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication failed for user nagios from 67.78.206.226
- sshd[25799]
[code]....
View 1 Replies
View Related
Feb 6, 2013
I am trying to harden my Nexus box and I am not able to ACL assigment command. Following are the commands I am trying to add.
interface cmp-mgmt module 5
Ip access-group NETWORK_MANAGEMENT_ACCESS in
View 1 Replies
View Related
Jun 26, 2012
when will be the command "default interface x/x" on the Nexus 5000 platform available? Even with latest software version (5.1.3.N2.1a) it is not possible. For Nexus7000 it's working fine with 5.2 train.Is there a feature request for it? If not here it is!!It's horrible to deconfigure many interfaces especially in N5k environments with many FEXes.
View 3 Replies
View Related
Jun 6, 2012
Customer production environment is nexus 5000 use 1 G interface * 4 and config Port-channel ( LACP ) uplink to C3560 , The port channel link is 802.1q trunk , but Data transfer is low , the sh int display as follow :
Why transfer performance pool and how to fix
N-5548UP# sh int ethernet 1/30Ethernet1/30 is up Hardware: 1000/10000 Ethernet, address: 547f.ee14.ed25 (bia 547f.ee14.ed25) MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA Port mode is trunk full-duplex, 1000 Mb/s, media type is 10G Beacon is turned off Input flow-control is off, output flow-control is off Rate mode is dedicated Switchport monitor is off EtherType is 0x8100 Last link flapped 9week(s) 6day(s) Last clearing of "show interface" counters 20w2d 30 seconds input rate 152 bits/sec, 19 bytes/sec, 0 packets/sec 30 [Code]...
View 1 Replies
View Related
Oct 17, 2012
We have network topo ( attach file)Two switch run VRRP, if I ping 10.0.10.3 from switch SW-6504-01 with source 10.0.10.2, ping lost one packet every 10 packets.We have other interface vlan with same problem
this is some config:
!
interface Port-channel1
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
no ip address
!
interface GigabitEthernet3/47
[code]....
View 5 Replies
View Related
Nov 12, 2012
NEXUS 7000 Octopus internal error in device 78 message. I got this on NEXUS 7000 logs:
Nov 12 22:05:14 smale-outside : 2012 Nov 12 21:05:14 BRST: %MODULE-2-MOD_DIAG_FAIL: Module 2 (serial: JAF1548AMKB) reported failure on ports 2/1-2/32 (Ethernet) due to Octopus internal error in device 78 (device error 0xc4e0025b)
Nov 12 22:05:17 smale-outside : 2012 Nov 12 21:05:17 BRST: %MODULE-2-MOD_FAIL: Initialization of module 2 (serial: JAF1548AMKB) failed
Nov 12 22:05:18 smale-outside : 2012 Nov 12 21:05:18 BRST: %MODULE-2-MOD_FAIL: Initialization of module 2 (serial: JAF1548AMKB) failed
[code]....
I only have found:
[URL]
which does not match reality : No one was configuring Vlans.
View 5 Replies
View Related
Jul 9, 2012
I've Nexus 7010 switch installed in my DC. I've conncected Cisco router to one of the Ports. On the same port I'm getting following error message and hence, unable to form EIGRP neighborship.
DR-CORE-SW-S01-NEXUS7K %MODULE-2-MOD_SOMEPORTS_FAILED:
Module 1 (serial: JAF*******NGK) reported failure on ports 1/2-1/2 (Ethernet) due
to R2D2 : Speed patch failed - no frames transmitted in device 143 (error 0xc8f0
1273)
View 1 Replies
View Related
Jan 9, 2013
I just barely put in a Cisco 3925 on our network. I've configured gigabitethernet 0/2 to live on our management VLAN with an IP address of 10.129.0.31/16. I did a "no shut" on the interface. Everything should be ready to allow me to ping and/or SSH to that interface but I can't. It's really weird because I've done this a thousand times (at least on ASAs). I must be missing something. At any rate, the default gateway of the management VLAN is 10.129.0.1. I can ping that from the router. I can also ping that from my laptop (which lives on a completely different VLAN). But I can't ping the router from my laptop or vice versa.
Building configuration...
Current configuration : 1360 bytes
!
! Last configuration change at 19:05:13 UTC Thu Jan 10 2013
!
[Code].....
View 4 Replies
View Related
Feb 7, 2011
I am trying to determin if Jumbo frames are enabled on out Nexus 7000, and I am getting mixed info back from the swtich.I looks like the system jumbo MTU size is 9216 by default, but the interfaces all say the MTU of the interface is 1500 bytes. According to this article, the interface MTU should read 9216 is the jumbo frames are enabled globally. Is this correct. Is there a way to verify if Jumbo frame support is turned on? [code]
View 4 Replies
View Related
Dec 3, 2011
I've got a 2621 configured as my main gateway to the internet - right now it's obtaining a DHCP ip from a the ISP's proprietary router set to bridged mode.
As of now, I'm unable to ping the internal interface of the router. I can ping external IP's only, even though I have DNS servers listed, i am unable to resolve host names. I'm running a few servers to which people are able to connect to my web server, among other services. I even have a crypto map setup to another 2621 across the country and can ping all internal ips on the other end... I JUST CANNOT PING THE INTERNAL INTERFACE of the router!!
I've noticed that when I ping the router during it's boot process (using linux un-interupted) I get a response in a very short window, then dies again. I'll post my config below:
[code]....
View 9 Replies
View Related
Dec 9, 2012
I have a Cisco 5548 Nexus switch with 10Gbase-SR interface transceiver. This interface is connected to Server chasis.
The show interface transceiver details output shows High ++ alarm for Current. Additionally, i am getting output errors on this interface.
View 1 Replies
View Related
Aug 20, 2012
I have configured the ip telnet source-interface Loopback 0 command on a Nexus7010, but when I telnet to another device and do a show users, the ip address is of the closest interface to the device I telnet to, not the ip address of the Loopback. All interfaces are in vrf default. I am running 5.1(6) NXOS.
View 6 Replies
View Related
Nov 6, 2011
I'm currently working on a plan to migrate our 6500's over to our new 7010's. At the time of the migration I want to tighten up our OSPF design and configure OSPF for "passive-interface default" then allow only those interfaces that should have OSPF neighbors to send the hellos. The issue is that the command is not showing up under the OSPF process. What's even more interesting is that the Nexus 5.x Unicast Routing Configuration Guide shows that the "passive-interface default" command should be an option to enter.
I'm currently running version 5.1(4) (though looking to upgrade to 5.2 during my migration testing). I would rather configure the passive-interface via the routing process versus having to enter it on every interface.
View 2 Replies
View Related
