Cisco Switching/Routing :: Error Logs On Nexus 7K Switch / %SYSMGR-2-STANDBY_BOOT_FAILED
Oct 29, 2012
We are getting some error logs on Nexus switch 7K.
Loggs:
----------
2012 Oct 30 22:36:07 SWITCH %CMPPROXY-STANDBY-2-LOG_CMP_UP: Connectivity Management processor(on module 6) is now UP
2012 Oct 30 22:36:40 SWITCH %SYSMGR-2-GSYNC_SNAPSHOT_SRVFAILED: Service "ipqosmgr" on active supervisor failed to sto
re its snapshot (error-id 0x40480005).
2012 Oct 30 22:36:40 SWITCH %SYSMGR-2-STANDBY_BOOT_FAILED: Standby supervisor failed to boot up.
2012 Oct 30 22:36:42 SWITCH %PLATFORM-2-MOD_REMOVE: Module 6 removed (Serial number JAF1550ATBR)
2012 Oct 30 22:42:08 SWITCH %BOOTVAR-5-NEIGHBOR_UPDATE_AUTOCOPY: auto-copy supported by neighbor supervisor, starting
[code]....
View 8 Replies
ADVERTISEMENT
Nov 21, 2012
We are getting some error logs on Nexus VDC,as follows:2012 Nov 23 08:49:11 N7K_B-Network_Center_B %$ VDC-3 %$ last message repeated 6 times 2012 Nov 23 08:50:21 N7K_B-Network_Center_B %$ VDC-3 %$ last message repeated 7 times 2012 Nov 23 08:49:11 N7K_B-Network_Center_B %$ VDC-3 %$ last message repeated 6 times2012 Nov 23 08:50:21 N7K_B-Network_Center_B %$ VDC-3 %$ last message repeated 7 times.
View 1 Replies
View Related
Jul 9, 2012
I've Nexus 7010 switch installed in my DC. I've conncected Cisco router to one of the Ports. On the same port I'm getting following error message and hence, unable to form EIGRP neighborship.
DR-CORE-SW-S01-NEXUS7K %MODULE-2-MOD_SOMEPORTS_FAILED:
Module 1 (serial: JAF*******NGK) reported failure on ports 1/2-1/2 (Ethernet) due
to R2D2 : Speed patch failed - no frames transmitted in device 143 (error 0xc8f0
1273)
View 1 Replies
View Related
Oct 13, 2012
We are using almost 10 Nexus 5k in our DC currently we are getting same error logs in all Nexus 5k." ntpd[4746]: ntp:time reset +0.279670 s " ,Is it major error or just for reset time?
View 1 Replies
View Related
Mar 22, 2012
Below memory status alerts of are seen on our syslog server for Nexus 7K switch(Default VDC).
PLATFORM-2-MEMORY_ALERT_RECOVERED: Memory Status Alert : CRITICAL ALERT RECOVERED
PLATFORM-2-MEMORY_ALERT_RECOVERED: Memory Status Alert : MINOR ALERT RECOVERED
PLATFORM-2-MEMORY_ALERT_RECOVERED: Memory Status Alert : SEVERE ALERT RECOVERED
Memory threshold Not created on Nexus. Can we ignore this alert or does it impact our current network traffic?
View 5 Replies
View Related
Feb 3, 2012
%SYSTEM_CONTROLLER-SP-3-ERROR: Error condition detected: TM_DATA_PARITY_ERROR Feb 2 10:57:09.602 EST: %SYSTEM_CONTROLLER-SP-3-EXCESSIVE_RESET: System Controller is getting reset so frequently
Cisco Internetwork Operating System Software
IOS (tm) s222_rp Software (s222_rp-IPSERVICES_WAN-M), Version 12.2(18)SXF15a, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2008 by cisco Systems, Inc.
Compiled Mon 20-Oct-08 19:20 by kellythw
Image text-base: 0x40101040, data-base: 0x42951080
[code]....
View 1 Replies
View Related
Sep 30, 2012
We use C2950G switches with IOS 12.1(22)EA12 . Switches are set up to send logs to a server (informationnal level). On this server, we receive many of logs from those switches, but none about interfaces errors (even if interfaces statistics show interfaces errors). On C3548 switches it's work fine.How should I be sure the set up of switches is correct ? Why do I never receive messages as %LINK-4-ERROR:[char] is experiencing errors ?
View 2 Replies
View Related
Aug 15, 2011
I m getting below error messages in show logs -
Aug 12 15:30:57.127 IST: %ENVIRONMENT-3-RPS_FAILED: Faulty internal power supply detected
Aug 12 15:31:02.175 IST: %ENVIRONMENT-3-RPS_FAILED: Faulty internal power supply detected
Aug 12 15:31:08.219 IST: %ENVIRONMENT-3-RPS_FAILED: Faulty internal power supply detected
Aug 12 15:31:10.239 IST: %ENVIRONMENT-3-RPS_FAILED: Faulty internal power supply detected
there is no error messages related to PSU in "show env all " log .
here is show version -
------------------ show version ------------------
Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6K2L2Q4-M), Version 12.1(22)EA13, RELEASE SOFTWARE (fc2)
Technical Support: [URL]
Copyright (c) 1986-2009 by cisco Systems, Inc.
[Code] ....
View 8 Replies
View Related
May 4, 2012
I am having some issues on my network and i think i have narrowed them down to a single switch.
On this switch the following logs can be seen
2147482407 05-May-2012 15:40:54 Informational %AAA-I-CONNECT: New http connection for user admin, source 10.0.5.135 destination 10.0.5.172 ACCEPTED
2147482431 05-May-2012 09:03:31 Warning %STP-W-PORTSTATUS: g13: STP status Forwarding
2147482432 05-May-2012 09:03:01 Informational %LINK-I-Up: g13
[code]......
All other switches are OK and do not show anything in their logs. I am trying to figure out what could be going wrong. Spanning tree is enabled on all switches. The switch tihs is happening on, ends in the ip 172 and is where all building cables connect to. They also connect to 174. I have attached an image of the infrastructure so you can visually see what i mean.
View 5 Replies
View Related
May 15, 2013
I am getting continous logs on my 4507 Switch :
May 16 12:45:09.000: %C4K_RKNOVA-4-INVALIDTOKENEXPIRED: STANDBY: Suppressed 302 times)Expired token 16490 in the invalid token list (NumEntries: 6) of type IrmPortId other id == 4294967287
May 16 12:45:09.000: %C4K_RKNOVA-4-INVALIDTOKENEXPIRED: STANDBY: Suppressed 302 times)Expired token 16490 in the invalid token list (NumEntries: 6) of type IrmPortId other id == 4294967287
does it lead to high CPU utilisation as well ??
View 1 Replies
View Related
Feb 7, 2013
I am not getting interface up/down logs in my switch console through show logging command. Switch model cisco WS-C4506-E and IOS :- cat4500e-ipbasek9-mz.122-53.SG3.bin. I have done below mention configurations, we can't configure logging level beyond informational. [code]
View 4 Replies
View Related
Sep 4, 2012
I encountered problem while trying to copy file from Nexus 5548 to my ftp server (proteus - 192.168.12.220 - the Nexus switch is able to resolve name proteus correctly to 192.168.12.220). See below the working and not working scenarios. I have serached through Cisco Bug Database but unable to find any related bug associated to this problem. This Nexus is running the following NX-OS version.
n5000-uk9-kickstart.5.1.3.N1.1a.bin
n5000-uk9.5.1.3.N1.1a.bin
Working (without specifying the username and full path)
[Code].....
View 1 Replies
View Related
May 27, 2013
I have in logs following error message:
%DEVICE_TEST-2-PWR_MGMT_BUS_FAIL: Module 1
Has failed test SpineControlBus 20 times on device Power Mgmt Bus on slot 10 due to error Spine control test failed error number 0x00000002.
View 3 Replies
View Related
Mar 4, 2013
I'm facing a problem regarding loss of ping packets when i do ping test from nexus3k to another nexus3k connected directly.however there is no error counters on the interfaces on both of devices.the ping failutre is occurring only whenever i do ping test with a large number of ping packets.I don't see the ping loss symptom with default ping test (default ping test is 5 packets).
H/W : N3K-C3548P-10G
S/W : 5.0(3)A1(1)
nexus3k# ping 1.1.1.2
PING 1.1.1.2 (1.1.1.2): 56 data bytes
64 bytes from 1.1.1.2: icmp_seq=0 ttl=254 time=2.732 ms
64 bytes from 1.1.1.2: icmp_seq=0 ttl=254 time=2.732 ms
[code].....
View 2 Replies
View Related
Oct 19, 2012
We inserted GLC-T modules and on Nexus 5548 they are showing SFP validation Failed , as per Cisco doc GLC-T is support . Since we have 28 such modules and all after inserting showing same error. please see the below details. I also try configuring speed and inserting modules but no result ..let me know whether my GLC-T module is supported on Nexus 5548
INMUMFDS1SWCORE01# show module
Mod Ports Module-Type Model Status
--- ----- -------------------------------- ---------------------- ------------
1 32 O2 32X10GE/Modular Supervisor N5K-C5548P-SUP active *
2 16 O2 16X10GE Ethernet Module N55-M16P ok
3 0 O2 Daughter Card with L3 ASIC N55-D160L3 ok
[code]
View 6 Replies
View Related
Aug 28, 2012
I have 2 datacenters running same equipement (two Nexu 5596 with FEX).I just took a look at the log just to see if everything is ok and I saw that I have the same error message (a lot of times) at both location :
%SYSMGR-FEX100-5-HEARTBEAT_LOSS: Service "satctrl" heartbeat loss 2 ,max 7,I though it was a problem with my peerklink-keepalive connection but I see the word FEX ....so i'm not sure...
Note that at both locations, my Nexus are connected back to back through the management port using transceivers. So it's a copper cable from the first nexus, going into a transceiver, going to another transceiver in fiber and then back to copper to the other nexus.
View 2 Replies
View Related
Jan 27, 2013
We have purchased two new Nexus 3548 switches. According to documenation the Nexus 3K does support vPC. When trying to enable the feature I get this:
nexus(config)# feature vpc
Error: vPC feature is not supported
nexus(config)#
We are running software version version 5.0(3)A1(1) and it looks like the latest version is 5.0(3)A1(2) so that's not much of a difference.Am I missing something here?
View 4 Replies
View Related
Dec 10, 2012
I have Nexus 7K installations in 2 locations. Both of them have multiple VDCs. In default VDC there are continous tacacs error message though tacacs is not configured. The requests are from various public IPs where thsi VDC is not exposed to Internet at all. What would be t he cause of it?
%AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication failed for user root from 195.2.219.2
2012 Dec 11 16:25:28 IDC-FBDTB-AMR2-CN7K-01 %AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication failed for user nagios from 67.78.206.226
- sshd[25797]
2012 Dec 11 16:25:34 IDC-FBDTB-AMR2-CN7K-01 %AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication failed for user nagios from 67.78.206.226
- sshd[25799]
[code]....
View 1 Replies
View Related
Nov 12, 2012
NEXUS 7000 Octopus internal error in device 78 message. I got this on NEXUS 7000 logs:
Nov 12 22:05:14 smale-outside : 2012 Nov 12 21:05:14 BRST: %MODULE-2-MOD_DIAG_FAIL: Module 2 (serial: JAF1548AMKB) reported failure on ports 2/1-2/32 (Ethernet) due to Octopus internal error in device 78 (device error 0xc4e0025b)
Nov 12 22:05:17 smale-outside : 2012 Nov 12 21:05:17 BRST: %MODULE-2-MOD_FAIL: Initialization of module 2 (serial: JAF1548AMKB) failed
Nov 12 22:05:18 smale-outside : 2012 Nov 12 21:05:18 BRST: %MODULE-2-MOD_FAIL: Initialization of module 2 (serial: JAF1548AMKB) failed
[code]....
I only have found:
[URL]
which does not match reality : No one was configuring Vlans.
View 5 Replies
View Related
Mar 30, 2013
Configuration details: I have 2 nexus 5K switches and both 5K is connected to four 2960 access switches in each floor through fiber(shown in the attached picture). I have configured each VPC for each floor and portchannel configuration on 2960s switch to communicate to 5K switches. Now I am not able to communicate PC 1 connected in 1st floor to PC2 connected in 4th Floor.
I have attached topology map of my infra and the configuration files also. 1st floor switch and 4th floor swich have same configuration except IP address and switch name.
View 3 Replies
View Related
Jan 7, 2013
I have a big doubt. Can I connect a LAN switch (i.e. 2960, 3560 or 3750) to a couple of Nexus 2000 FEX (i.e 2232P or 2248TP) and have a Port-Channel or vPC with STP active and several VLANs through this Port-Channel? Or Can I only connect servers to these N2K FEX?
View 3 Replies
View Related
Jan 2, 2013
We recently had a pair of Nexus 5k switches setup in our network. We had professional services handle the initial configuration but they weren't able to setup config sync for us. Each Fex is connected to each 5k, so we need a switch-profile to maintain a consistent setup on our interfaces. I went through the process in Configuring Switch-Profiles, but when I check the status of the peer, it says not reachable. [code]
View 1 Replies
View Related
Oct 8, 2012
Current our environment is the following:
Core1 ---- Core2
| |
Nexus5k
| |
N2k, N2k, N2k (FEX)
||
Servers, hosts, etc..
We would like to add another Nexus5k to this topology. However, it has to be a zero downtime infrastructure add-on. When setting up the keep-alive, peer-link, vPC and vdc domain, will there be any upset in network traffic on the current N5k?Also, are the Nexus5k configurations synchronized or are they independent from one another? Before setting up the new 5k, should i configure it to teh 6509's, and vPC's to the Nexus2k's before setting up peer-link?
View 2 Replies
View Related
Oct 31, 2012
My network consist of that network device. cisco catalyst 3750 with stackwise, 2xnexsus 5000 series and servers.servers connected to nexsus switch. nexsus connect to 3750.
Each server have two link, one of them connect nexsus1 and other connect to nexsus2 switch.(same traffic) each nexsus have one link to 3750. At 3750 the nexsus link configurate etherchannel. but the flapping occur at 3750.
i understand that at 2 nexsus link have the same server source mac address so the flapping occur at 3750. how i solve this problem?
View 5 Replies
View Related
Jul 31, 2012
Trying to find some documentation as to whether there are any other steps for inserting this new module in our N7K. We have 2 blades in already and 2 Sups in 5 & 6. I'm assuming its like the 6500s, where we just slide it in and the OS configures the global parms for it and the default VLAN.
View 2 Replies
View Related
Jul 15, 2012
My Name is senthil i need to configure new hp sever with Nexus 5548 how to config.. server side everything finished just i need only
Config tips for Nexus 5k for New server
View 2 Replies
View Related
Oct 17, 2012
We have Nexus 5K switches at the aggregation layer and VPC domain has been configured on them. VPC domain includes switches at the access layer as an identity.But when primary switch reboots failover didn,t happened. We are attaching architecture diagram for the setup along with show tech for Nexus 5K both switches.
View 2 Replies
View Related
Mar 13, 2013
My cisco 4948 switch is generating the below error,how do i troubleshoot this error.
*Mar 13 00:09:33.451: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 14 times)Packet received with invalid source MAC addre ss (00:00:00:00:00:00) on port Gi1/37 in vlan 1Gi1/37- to this port another 2950 switch is connected by trunk link.and to this switch end host is connected i.e.thin client
View 3 Replies
View Related
Nov 29, 2011
i'm trying to enable command authorization for ssh as well as console access to a Nexus 7010 box (version 5.0). Following is the config:
aaa group server tacacs+ ACS5-1
server 10.12.19.11
server 10.12.19.12
source-interface loopback0
snmp-server enable traps aaa server-state-change
aaa authentication login default group ACS5-1 local
[code]....
As you can see, the default group configuration ACS5-1 for authenticatoin has applied to both defaults and console. But the command authorization does not appear to be applied to the console. As a result, when i login from the console and get authenticated, the command authorization does not trigger and i can run commands I'm not supposed to. In the configuration, I do not see "aaa authorization console" option unlike we have in IOS.
View 2 Replies
View Related
Sep 7, 2012
We have two catalyst 6506 switches with 10 gb u plinks and around 120 edge switches cat 3750-x switches. Still the module on the core wheere servers are connected is 1000mbps port.Now if we induct a nexus switch to the datacenter what kinds of benefits we can reap In a virtulised environment as well as real environment?following are the some of the queries.Can we reduce the number of edge switches? ( by virtual environment), Inter operabaility between cat ios and nexus ios, how this will affect the environement,What will be the over all benefits ?, What are the cons of this induction ?
View 22 Replies
View Related
Nov 28, 2011
we have e requirement for a Nexus 5000 switch to be accessed and managed inband, ie the Management interface can't be connected to the rest of our networks management VLAN because the switch is remote and only connected via fibre. We have enabled the interface VLAN feature and configured an interface VLAN but can't seem to PING the IP address configured on it ?
View 10 Replies
View Related
Dec 11, 2011
Is it possible to cascade a (fiber) Dell switch to Nexus5000 as shown above ?
View 4 Replies
View Related
Jun 11, 2013
i want to remove the sync-profile on each of two synchronized Nexus 5596UP without loosing the config stored in Switch-Profile. That means without connectivity interruption and re-configuration of interfaces in "conf t mode", for example. Since NX-OS Release 5.2(1)N1(1) there is a new command
switch(config-sync)# no switch-profile abc profile-onlyprofile-only—Deletes the switch profile without the local configuration.
[URL]
View 2 Replies
View Related
