I have a Cisco ASA 5505, the problem is I am not able to ping to outside natted interface (ip: 172.88.188.123 and 124 and 125) from inside network I have looked for ASA documentation through the internet and still got nothing.
the config are:
: Saved
:
ASA Version 8.2(1)
!
[Code].....
I have a new ASA 5505 and all is working fine, I can CLI and ASDM into it, but just can't ping the inside interface, do I need to enable a feature to make this work somehow?
View 1 Replies View RelatedI have an ASA 5505 that I'm trying to set up a guest network on. I've configured an interface as a trunk and allowed the 2 vlans but I'm not getting any layer 3 to it. The switch connected to it is a 3560 and port is configured as a trunk with the same vlans.
I can't ping the ASA inside interface but I see its MAC address in the swtich's table.
[code]....
I am having a problem configuring my ASA 5505 for NAT.
View 3 Replies View RelatedI have a Cisco ASA 5505 and I have my internal and external interfaces configured but I currently cannot ping from the inside to an IP Address on the outside. I had this setup and working and I have another set of equirement that I am replacing that is working with my service provider so I know it is a configuration issue. When I ping 4.2.2.2 for example I get:
Destination host unreachable
Do I need to add a static route from my inside interface to my outside interfaces?
: Saved
:
ASA Version 8.2(5)
!
hostname pxasa
[Code].....
I'm trying to set up a Guest VLAN for wireless at a client site, and I feel like I'm missing something small in the configuration, since I can't ping any of the VLAN interfaces from my laptop when the address is statically set to something in the 172.20.100.x range.
I've pasted the configs for the ASA 5505 and the 6 switches below for convenience. Near as I can tell, all should be well. The ports are in trunking mode, the "show cdp neighbors" command returns the proper information, VLAN 100 exists on all the switches, etc.
Code:
ASA Version 7.2(4)
!
hostname ASA
domain-name xxxx.local
enable password Cj3LF.ehxXN3xVkxWcxd encrypted
passwd Cj3LF.ehxXN3xVkWcxd encrypted
[Code] ......
I've recently upgraded my old firewall from a PIX to an ASA5505 and have been trying to match up the configuration settings to no avail. I have is that I can't ping the new firewall on it's inside interface, despite having "icmp permit any inside" in the running config. Secondly, the server I have on there ("Sar") can't connect out to the internet.I've included the ASA's running config incase anybody can see if something stands out. I have a feeling it's either not letting anything onto the inside interface, or there is no nat going on. Lastly (and possibly relevant), the firewall is actually going at the end of a vlan, which is different to the firewall's inside vlan number. I don't know if this is actually the problem because the server can't connect out even if connected directly into the firewall.
View 32 Replies View RelatedI cannot seem to ping from the outside of my 5520 firewall to an inside network. I have a single physical outside interface connected to a Layer 2 switch, with a laptop connected to it. This is on network 10.11.131.0/28. From there, I cannot ping to the inside interface (which is a sub interface on G0/0) with network 10.11.130.0/24/ For some reason, it doesnt work.
Now. I had access-lists in place, but have removed them for testing and it still doesnt work. I have set the security level of inside and outside to 100, and entered the same-security-traffic permit inter-interface command - still no joy. Below is the relevant configuration.
Inside Interface
interface GigabitEthernet0/0.96
description L3 Interface - Informational Zone
vlan 96
[Code].....
I'm currently configuring an ASA5510.I connected a laptop (IP 192.168.96.18/255.255.255.0) to port 0/2 and tried to ping 192.168.100.2 ... impossible to ping outside interface.I resetted the config of the ASA to retest more simple. [code]
View 1 Replies View RelatedI ran into a very strange icmp ping issue. The network has been working fine other than the issue listed below, L2L VPN works fine and all three data centers can access each other via L2L VPN.I have three ASA5510. [code]
View 5 Replies View RelatedThe ASA is configured in very simple transparent mode. As desired, traffic can flow in each direction between inside and outside. I can manage the ASA via console and direct connection to the management interface. The problem is that I cannot ping or ssh to the ASA via the inside interface. I need to be able to manage the ASA from any PC on the inside LAN. I suspect I am missing some easy aspect of the configuration but after a lot of hours I'm about at the end of my patience with it. Here is what I believe to be the relevant parts of the config.
ASA Version 8.2(1)
!
firewall transparent
hostname issr1
enable password 2alej83t5cqT0FWd encrypted
passwd 4kleUY438I93.4ljdh encrypted
names
[code]....
So I have a client with an ASA 5520 running version 9.0 (was on 8.4) that I am trying to get either IPSec or SSL VPN configured on. I got everything setup and tried to connect. However, I couldn't connect to either. I fired up the real time monitoring and didn't see any syslog messages referring to a VPN build up. I also enabled SSH/Telnet on the outside interface and cannot connect to the ASA outside interface. I can ping the outside interface and can ping the internet from the ASA. I did set up a test ACL on the ASA and ran packet tracer on it and the results came back fine.
There is an IPS in the ASA as well, but I disabled the ACL for that and still am having these issues. Part of me wonders if the ISP has something set up to block inbound traffic. This should be a business class connection.
I have a Cisco ASA 5505 in our office. We are currently using Interface 0 for outside and 1 for inside. We only have 1 Vlan in our environment. We have two three switches behind the firewall. Today the uplink to Interface 1, to the firewall, on the switch went bad. I want to setup a second inside interface on the firewall and configure it as failover incase this happens again. I want to attach it to the other switch. Can I do this? If so, what do I need to do? would it only be a passive/standby interface?
View 1 Replies View RelatedI have been working with ASA 5510,20,40,80 but not with 5505 this vlan and its interfaces are quite confusing.Just want to know how it works and its connectivity to Cisco Switch.Do i have to put the interface of the switch in the same vlan as i am creating the interface vlan in firewall ?Now the switch port connecting to this Eth1 interface should also be in the same vlan ? i.e vlan3 ?? or it will be in trunk ? The default configuration shows the eth0 with no access vlan and interface eth1 with access vlan 2... does it mean the eth0 is in vlan1 ? (Nativ Vlan ) ???
View 4 Replies View RelatedOne of my client has BSNL leased line with LAN IP POOL we configured those on ASA 5510 nad Internet working fine but from cloud we are not getting any response for ping requiest please find running configuration below:
ciscoasa(config)# sh run
: Saved
:
ASA Version 8.2(1)
[Code]....
one of my SNMP server 10.242.103.42 sits in MZ zone,and ACE 4710 is connected to core switch,coreswitch is connected to firewall asa.
Now iam trying to ping from MZ zone SNMP server to loadbalancer ip 10.242.105.1,iam unable to ping my LB interface to discover SLB on my SNMP server.
I just tried to configure my ASA but unable to ping. My setup is as follows:
Cable Modem (DHCP from IPS)---> ASA (192.168.1.1)--->Belking Router (192.168.5.1)--->Switch (192.168.5.14)--->
ASA Version 8.2(3)
!
hostname WoodHomeASA-1
[Code].....
i am trying to get my ASA 5505 with 2 internal VLANs (voice and data) and external internet VLAN to run in router as a stick, and route between VLANS.
I cant get it working though:
[code]...
We want to use an ASA as a pure routing device. Our network has several internal subnets (10.1.x.0/24), and we want to be able to reach them from outside and to allow access between them.
We have a defined a VLAN for each subnet range with the same security-level, added it to an Ethernet port and made the Ethernet that acts as outside as a trunk, and defined it as the global routing.
We cannot ping any of the subnet IPs defined in the ASA from outside nor we can ping it from the internal IP addresses.
Configuration:
: Saved
:
ASA Version 8.2(1)
[Code].....
I am trying to configure Nat on a clean ASA 5505, but can't get it to work. I ran the commands below. On the ASA I can ping the internet and inside vlan ip. On my laptop I can ping the ASA inside vlan ip, but I can't ping the outside vlan ip. From another network I can ping the ASA outside public ip. Is there an access-list that denies inside from accessing outside?
I am running version 8.4(3) and I erased the existing configuration.
ASA(config)# interface vlan 1
ASA(config-if)# ip address 10.0.0.1 255.255.255.0
ASA(config-if)# nameif inside
[Code].....
I have 2 ASA and would like to build a Side-to-Side VPN between these ASA. So I can learn something about configure a ASA for different thinks. But now I don`t can Ping from a Client to the Internet-Router.My Configuration is:
Client IP 192.168.1.100 <===> ASA Inside 192.168.1.1 /Outside 192.168.178.254 <===> Router 192.168.178.1
Is there something wrong at my config? or do I need inside private Adresses and at the Outside Global IP`s.
At the Router I have a Static Route that the 192.168.1.0 / 24 ist to find over Gateway 192.168.178.254
I have been tasked with replacing our company eSoft router with a Cisco ASA 5505 with the upgraded security license. I have been working on the configuration for a couple of weeks now, after reading hundreds of forum posts, watching youtube videos, and endless google searching, and despite my best efforts I am still having an issue I can’t figure out.
I have a couple of subnets, that when the ASA is connected, I cannot ping, nor can they get to the internet or our Exchange server. At this point I’m not sure if it’s an access rule issue, NAT issue, or DNS issue.
Here is the network layout:
ASA: 192.168.0.2 (Primary Gateway)
192.168.0.0 (Primary facility, ASA is the gateway)
192.168.2.0 (Second facility, connected via Verizon point-to-point)
192.168.3.0 (Third facility, connected via Verizon point-to-point)
[Code].....
I am trying to troubleshoot an ASA5505 connectivity issue. My initial tests are to ping the Internet router from the ASA This is failing and also a sh arp only shows internal addresses.
I have to go to site to check this out to confirm the following.
1: Should I be able to ping the Internet router from the ASA?
2: Do I need to permit any icmp to do this?
3: Should a sh arp show the address of the internet router?
I tried entering the command permit icmp any outside
However I got the error route already exists 0.0.0.0/0.0.0.0
I am unable to ping inside interface (Rin) to outside interface (Rout) of my Cisco ASA 5520 runing on ASA Version 8.4(1).
ASA Version 8.4(1)
!
hostname FW5520
[Code].....
When I tried to upgrading PIX525 6.3 to 7.0 , Not able to Ping the host from the PIX 525 Inside interface which is on the same subnet, Also from the host to Inside Interface , Tried with Directly connected laptop with Cross cable and using Straight cable via switch, But the results end with fail.
View 2 Replies View RelatedI have setup 5505 ASA for Testing purposes. It has static route to layer 3 switch on outside interface that goes to the internet.
ciscoasa# sh route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
[Code].....
I've configured a 5505 but internal clients can't ping external ip. To test I've connect a pc with the ip of the default router on the Outside int the ASA can ping the PC and the PC can ping the ASA, but internal clients can't ping the PC
PC config 195.12.23.241/28
Here's the ASA config, so far I've wiped the ASA and started with a blank sonfig and built it up but still not working.
ASA Version 8.2(5)
!
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
[Code] .....
I configured a new Asa 5505 with Ios 8.44-1-k8.bin and when I installed the Asa the client's after about 1 hour were unable to ping or map drives to the Asa. I got the following error,%ASA-2-106007: Deny inbound UDP from XXXX to XXXX due to DNS Query. I added the command same-security-traffic permit intra-interface they were then able to ping the server and connect to the Internet, but still unable to map drives i could see the connections from the Pc's to the server in a show conn with was tcp port 445 with Saa? I reverted back to Ios 8.25 and everything works.
View 2 Replies View RelatedI have a ASA 5505. I want to be able to ping from my workstation to some address, lets say [URL]. My workstation is connected to Ethernet 0/2. I have tried playing around with the ACL but am not able to accomplish this.
Result of the command: "show running-config"
: Saved:ASA Version 8.2(1) !hostname ciscoasadomain-name home.7vnmotorsports.com
[Code]....
I am trying to access and ping the inside interface of a ASA5505 from a remote network. From the remote network, I am able to access anything on the local network, but the ASA5505 inside interface.The 2 networks linked by a fiber link which have a transport network on another interface. From the remote network, I am able to ping the transport network interface IP, but I would like to be able to ping the inside interface IP. When I do a packet tracer, I get a deny from an implicit rule.How can I achieve that?
Here are the subnets involved and the ASA5505 config.
Remote network : 10.10.2.0/24
Local network : 10.10.1.0/24
Transport network : 10.10.99.0/24
[code]....
I want to creat sub int on ASA 5505 but when I am trying below command it show error.
------------------------------------
config t
int f0/0.3400
------------------------------------
My ASA software version is 8.2(5).
Can we make sub interface on Cisco ASA 5505 model and if its possible then do that interface need to be upgraded into Trunk Port.
View 8 Replies View RelatedBefore upgrading to 8.4(4)1 I was able to ping our inside interface accross the VPN. Now I cannot. Because ping is not working, my SNMP server thinks that the device is offline however I know the VPN tunnel is still up and the remote branch office is working fine. Here is the config of the branch office ASA 5505 in question. How to get icmp working again?
ASA Version 8.4(4)1
!
hostname BranchASA5505
domain-name houston.deh
[Code].....