Cisco Firewall :: 5505 - Ping And SNMP Broken After 8.4(4)1 Upgrade?
Sep 19, 2012
Before upgrading to 8.4(4)1 I was able to ping our inside interface accross the VPN. Now I cannot. Because ping is not working, my SNMP server thinks that the device is offline however I know the VPN tunnel is still up and the remote branch office is working fine. Here is the config of the branch office ASA 5505 in question. How to get icmp working again?
ASA Version 8.4(4)1
!
hostname BranchASA5505
domain-name houston.deh
[Code].....
View 2 Replies
ADVERTISEMENT
Sep 7, 2011
How I can actively monitor the interfaces and overall status of 2 x ASA 5500s in an Active/Standby configuration?
I can setup monitoring of the interfaces on the Active member but I'm not sure how to manage the Standby member?
View 1 Replies
View Related
Mar 27, 2008
I am trying to monitor my ASA 5505. This asa is connect via a ip-sec tunnel to our network. I have no problems with snmp monitoring devices behind the ASA, but when trying to monitor the asa itself I do not get a SNMP response.
View 2 Replies
View Related
Apr 26, 2011
Broken Pat/Overload after upgrade from 1711 to 891
View 7 Replies
View Related
Apr 21, 2013
I've got a little problem with my ASA 5515-X after upgrade from version 8.6 to 9.1.
I've got two 5515-X in A/S-mode and upgraded both as described on cisco's website (first standby-unit, failover, etc.). Everything worked just fine except pinging the ASA-interfaces themselfes. Before upgrade it was possible to ping from any subnet to the internal interface, but now it's not. If I'm on the router next to the ASA I'm able to ping, but every ping from behind that router fails. The ICMP-packets get into the ASA (counter on ACL raises up), but no reply is getting into the source.
The configuration fir ICMP was not changed and says "permit 0.0.0.0 0.0.0.0" for any ICMP on the internal interface. The router betwenn my subnet and the ASA has no ACL installed and - as said above - the ICMP gets obviously to the ASA but doesn't come back!?
View 4 Replies
View Related
Mar 7, 2013
I have a TAC case open, but it doesn't seem to be making any progress.I upgraded my 5508 controller from 7.2.111.3 up to 7.4.100.0..Most of my APs are fine. 3500s, 1100s etc.except for 602i APs. The APs associate, they update software etc, but they won't broadcast the WLAN.An interesting thing, on the 602 AP, in the log, I see this:*Mar 06 15:08:12.667: SSID remote, WLAN Profile Name: RemoteOEAP, added to the slot[0], disabled..So the AP is definately talking to the WLC and being pushed the correct WLAN profile.On the controller, the AP shows the the Admin status of the radios is showing DOWN, but the Admin status on the AP itself shows UP
I've done a factory reset on the APs to no avail. I have a 2504 WLC as well that i'm in the process of implementing in a DMZ specificially for these APs, and for testing purposes, I associated the 602 Ap to that WLC as well. This one is running 7.4.100.0 too, same results. It would appear to be a problem with this version of software?
View 6 Replies
View Related
Jan 16, 2012
We currently have a central hub using an ASA5510 and then a few site-to-site VPN connections to our support staff homes. The devices at the homes are Cisco routers. We were running version 8.25 on the ASA and all was working fine. We recently upgraded to version 8.42 and although all the functionality of the network is ok and it does what it should, our support staff cannot ping, ASDM or telnet to the ASA inside interface anymore whereas they could before the upgrade. The home VPNs all run on a 10.30 subnet (i.e. 10.30.1.x, 10.30.2.x etc etc). I can post our config (security edited of course), but it is quite a big config. The command management-access inside is specified and the 10.30.0.0/16 subnet is permitted to ASDM and Telnet. Are there any extra things that have to be done in version 8.42 to get this to work as the support staff do have to access the firewall for configuration purposes. At the moment, they have to telnet to one of the routers on the local LAN and then Telnet to the firewall from there.Prior to the upgrade, they were all able to ping the inside ASA interface and also telnet and HTTPS to it from their PCs at home. Now they cannot and the only change made was an upgrade to 8.42. Immediately after the upgrade none of them can ping the interface anymore and it seems it can only be accessed from the local LAN. I cannot find any access-lists that might be blocking the packets so can only assume it's something in the way 8.42 works.
View 8 Replies
View Related
Feb 27, 2013
I'd like to see some REAL LIFE comparisons of ASA firewall throughput (a bit like this one for ISR G2 Routers - [URL].
The reason I ask is that I recently upgraded a firewall from an ASA5505 to an ASA5520 on a small network where the only outside connectivity was a single 10meg Internet circuit with an IPSEC VPN (not landed on the firewall but on a router) to another site.
When I swapped out the firewall the users noticed a big improvement. The firewall is not doing anything out of the ordinary - no IPS or VPN, just standard state full inspection.
View 5 Replies
View Related
Sep 9, 2011
I just tried to configure my ASA but unable to ping. My setup is as follows:
Cable Modem (DHCP from IPS)---> ASA (192.168.1.1)--->Belking Router (192.168.5.1)--->Switch (192.168.5.14)--->
ASA Version 8.2(3)
!
hostname WoodHomeASA-1
[Code].....
View 30 Replies
View Related
May 24, 2012
i am trying to get my ASA 5505 with 2 internal VLANs (voice and data) and external internet VLAN to run in router as a stick, and route between VLANS.
I cant get it working though:
[code]...
View 4 Replies
View Related
Sep 7, 2011
We want to use an ASA as a pure routing device. Our network has several internal subnets (10.1.x.0/24), and we want to be able to reach them from outside and to allow access between them.
We have a defined a VLAN for each subnet range with the same security-level, added it to an Ethernet port and made the Ethernet that acts as outside as a trunk, and defined it as the global routing.
We cannot ping any of the subnet IPs defined in the ASA from outside nor we can ping it from the internal IP addresses.
Configuration:
: Saved
:
ASA Version 8.2(1)
[Code].....
View 3 Replies
View Related
Jun 17, 2012
I am trying to configure Nat on a clean ASA 5505, but can't get it to work. I ran the commands below. On the ASA I can ping the internet and inside vlan ip. On my laptop I can ping the ASA inside vlan ip, but I can't ping the outside vlan ip. From another network I can ping the ASA outside public ip. Is there an access-list that denies inside from accessing outside?
I am running version 8.4(3) and I erased the existing configuration.
ASA(config)# interface vlan 1
ASA(config-if)# ip address 10.0.0.1 255.255.255.0
ASA(config-if)# nameif inside
[Code].....
View 8 Replies
View Related
Sep 29, 2012
I have 2 ASA and would like to build a Side-to-Side VPN between these ASA. So I can learn something about configure a ASA for different thinks. But now I don`t can Ping from a Client to the Internet-Router.My Configuration is:
Client IP 192.168.1.100 <===> ASA Inside 192.168.1.1 /Outside 192.168.178.254 <===> Router 192.168.178.1
Is there something wrong at my config? or do I need inside private Adresses and at the Outside Global IP`s.
At the Router I have a Static Route that the 192.168.1.0 / 24 ist to find over Gateway 192.168.178.254
View 2 Replies
View Related
Aug 4, 2012
I have been tasked with replacing our company eSoft router with a Cisco ASA 5505 with the upgraded security license. I have been working on the configuration for a couple of weeks now, after reading hundreds of forum posts, watching youtube videos, and endless google searching, and despite my best efforts I am still having an issue I can’t figure out.
I have a couple of subnets, that when the ASA is connected, I cannot ping, nor can they get to the internet or our Exchange server. At this point I’m not sure if it’s an access rule issue, NAT issue, or DNS issue.
Here is the network layout:
ASA: 192.168.0.2 (Primary Gateway)
192.168.0.0 (Primary facility, ASA is the gateway)
192.168.2.0 (Second facility, connected via Verizon point-to-point)
192.168.3.0 (Third facility, connected via Verizon point-to-point)
[Code].....
View 7 Replies
View Related
Mar 19, 2013
I am trying to troubleshoot an ASA5505 connectivity issue. My initial tests are to ping the Internet router from the ASA This is failing and also a sh arp only shows internal addresses.
I have to go to site to check this out to confirm the following.
1: Should I be able to ping the Internet router from the ASA?
2: Do I need to permit any icmp to do this?
3: Should a sh arp show the address of the internet router?
I tried entering the command permit icmp any outside
However I got the error route already exists 0.0.0.0/0.0.0.0
View 2 Replies
View Related
Nov 14, 2011
I have a Cisco ASA 5505, the problem is I am not able to ping to outside natted interface (ip: 172.88.188.123 and 124 and 125) from inside network I have looked for ASA documentation through the internet and still got nothing.
the config are:
: Saved
:
ASA Version 8.2(1)
!
[Code].....
View 2 Replies
View Related
Feb 27, 2011
I'm getting ready to reload an ASA that will be a long drive if it doesn't come back up after this upgrade attempt.
View 9 Replies
View Related
Apr 20, 2011
I open case open to the Cisco about I am not able to get the SSH connection from ASA 5505 after upgrade the IOS 8.2.3 and Device Manager 6.3.3 from the older IOS 7.2.4 and device manager 5.2.4.
I am working in MNC and we have more than 30 office around the world.We have all offices have ASA5505 which we upgrade 3 years before and Now We are in procession to upgrade the IOS on all ASA5505 to all 30 offices.
But after I upgrade the 10 offices and relieze that not able to get SSH connection to ASA5505 with new IOS 8.2.3.I opened the 2 times case and call the Cisco Technical but no luck so far.
View 11 Replies
View Related
Jan 18, 2012
I have been delaying an upgrade past 8.2.5 because it is stable and I didnt feel like learning a new way of doing NAT because of the way the code was changed. What is forcing me to go down this path is that I need to be able to let protocol 41 pass through the firewall which doesnt work in 8.2.5 and is what is making me look at 8.3 or 8.4
I know that I will have to install a memory upgrade on both my lab 5505's before I can install the upgraded binary. Will be ordering that in the next few days.
Any suggestions on going to 8.3 or 8.4 based on the reason for the upgrade ? I had been told by TAC to stay away from 8.3 but never got a good reason for that. My lab config (i.e. home ASA) is pretty straight forward (no SSL or IPSEC config), so I would hope it would go fairly smooth. I had heard a lot of horror stories early on but wanted to see how things had been going for everyone with the later versions of code.
View 1 Replies
View Related
Aug 3, 2011
I just upgraded an ASA5505 running 8.4.1 to 8.4.2 after noticing that I was experiencing the ssh bug described here: [URL]. Now every time I reload the unit I get the following message on the console:
Reading from flash...
!!...
Cryptochecksum (unchanged): b19f76ce 30b189e5 9272b4d4 4f746634
Type '?' for a list of available commands.
[Code]...
I tried searching for this message with no luck at all. The firewall seems to be working ok as I can still get online and my VPN tunnels are up,
View 3 Replies
View Related
May 10, 2011
I have a new ASA 5505 and all is working fine, I can CLI and ASDM into it, but just can't ping the inside interface, do I need to enable a feature to make this work somehow?
View 1 Replies
View Related
Apr 5, 2013
I have setup 5505 ASA for Testing purposes. It has static route to layer 3 switch on outside interface that goes to the internet.
ciscoasa# sh route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
[Code].....
View 20 Replies
View Related
Nov 4, 2011
I've configured a 5505 but internal clients can't ping external ip. To test I've connect a pc with the ip of the default router on the Outside int the ASA can ping the PC and the PC can ping the ASA, but internal clients can't ping the PC
PC config 195.12.23.241/28
Here's the ASA config, so far I've wiped the ASA and started with a blank sonfig and built it up but still not working.
ASA Version 8.2(5)
!
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
[Code] .....
View 2 Replies
View Related
Aug 12, 2012
I configured a new Asa 5505 with Ios 8.44-1-k8.bin and when I installed the Asa the client's after about 1 hour were unable to ping or map drives to the Asa. I got the following error,%ASA-2-106007: Deny inbound UDP from XXXX to XXXX due to DNS Query. I added the command same-security-traffic permit intra-interface they were then able to ping the server and connect to the Internet, but still unable to map drives i could see the connections from the Pc's to the server in a show conn with was tcp port 445 with Saa? I reverted back to Ios 8.25 and everything works.
View 2 Replies
View Related
Dec 12, 2011
I have an ASA 5505 that I'm trying to set up a guest network on. I've configured an interface as a trunk and allowed the 2 vlans but I'm not getting any layer 3 to it. The switch connected to it is a 3560 and port is configured as a trunk with the same vlans.
I can't ping the ASA inside interface but I see its MAC address in the swtich's table.
[code]....
View 4 Replies
View Related
Jul 30, 2011
I have a ASA 5505. I want to be able to ping from my workstation to some address, lets say [URL]. My workstation is connected to Ethernet 0/2. I have tried playing around with the ACL but am not able to accomplish this.
Result of the command: "show running-config"
: Saved:ASA Version 8.2(1) !hostname ciscoasadomain-name home.7vnmotorsports.com
[Code]....
View 5 Replies
View Related
Feb 28, 2013
I have been browsing the forum and the support notes for a couple of hours and haven't found a definitive answer to my question. Our ASA is on the subject versions. I watched a video on YouTube stating that upgrading the ASA is easiest if you upgrade ASDM, then the ASA. Problem is, I don't think I can upgrade ASDM first because I don't see a version that is compatible with ASA 7.2.x and 8.0.x.
View 3 Replies
View Related
Jan 30, 2012
I am trying to get experience with 8.4 code on my 5505. I purchased a Cisco 512MB memory upgrade and installed it. It booted up once and I thought I was ok. I then looked down and noticed that all lights were blinking on the front panel and I had no console access.
[code]...
View 5 Replies
View Related
Jan 24, 2013
I am trying to find out the best path to upgrade to two ASA 5510 running 9.0 (1). I know there are changes in the new version. Let me know what information you need and i will post.
View 2 Replies
View Related
Dec 17, 2012
I have a Cisco ASA 5505 device with basic (default) license, currently all my reirections, VPN's, VLAN's(3 Vlan's) etc are configured on the same and are working fine.Now i need to upgrade my basic license to "Security Plus" for some additional features, if i upgrade it directley is there any complications in present rules, below is my doubhts
1. if i upgrade, did it change any of my present configurations ?
2. is there any name change or property changes for VLAN's or VPN's
3. did it affect the firewall functions
4. If anything goes wrong, can i restore it in to my old state using my previous dump.
View 1 Replies
View Related
Nov 16, 2011
I have successifuly upgraded ASA and ASDM image. My question is how to make it to boot it as default when you do a factory reset of the device. For the ASA image I found out that it will boot the first image it founds on the flash, so I left only the latest bin file and if I do factory reset it boot the latest. But for ASDM it still boots the old one, because there is no "asdm image disk0:/asdm-645.bin" command in the config. I`m not sure how, because I only left the new ASDM bin image. Is there any variable or something that still points to old asdm image?
My ASA version is 8.4(2) and ASDM 6.4(5). The old one was ASA 8.2 and ASDM 6.3.
View 2 Replies
View Related
Jan 15, 2012
Cisco ASA 5505 Cannot Ping Secondary Internal Network.
View 9 Replies
View Related
Jul 24, 2012
I have, what I believe to be, a simple issue - I must be missing something. Site to Site VPN with Cisco ASA's. VPN is up, and remote hosts can ping the inside int of ASA (10.51.253.209). There is a PC (10.51.253.210) plugged into e0/1.
I know the PC is configured correctly with Windows firewall tuned off. The PC cannot get to the ouside world, and the ASA cannot ping 10.51.253.210.
I have seen this before, and I deleted VLAN 1, recreated it, and I could ping the local host without issue. Basically, the VPN is up and running but PC 10.51.253.210 cannot get out
ASA Version 7.2(4)
!
hostname *****
domain-name *****
enable password N7FecZuSHJlVZC2P encrypted
[Code]...
View 2 Replies
View Related
