Cisco :: Access Point Air-Lap1242 / It Won't Save Config
Jan 6, 2013
I have 2 Air-Lap1242 that wont save their config after reboot. They are managed by a WLC (4404) and it all seems pretty fine and dandy, but when i reboot them, they dont want to save anything.
I am setting them up as bridges (mesh), and it works until i reboot them, then I have to do it all over again.Using CLI to type in "write mem" or "copy running-config startup-config" only results in: "Building configuration... [OK] -> NVRAM Verification Failed".
View 8 Replies
ADVERTISEMENT
Nov 18, 2011
I have 2 Air-Lap1242 that wont save their config after reboot. They are managed by a WLC (4404) and it all seems pretty fine and dandy, but when i reboot them, they dont want to save anything.I am setting them up as bridges (mesh), and it works until i reboot them, then I have to do it all over again.Using CLI to type in "write mem" or "copy running-config startup-config" only results in.
View 1 Replies
View Related
Sep 26, 2012
I have ASA 5505 and I save the configuration in the ASA 5505 using write memory or using copy run start but whe i unplug the power cord and plug it back in the ASA gets its factory default configuration.
View 8 Replies
View Related
Jun 5, 2011
I have Linksys SPS224. I've learnt how to change some parameters through SNMP. But this changes are applying to running-config, and, when switch reboots, all loose.
How can I save this changed running-config to startup-config through SNMP?
View 1 Replies
View Related
Jul 4, 2012
I have a 3750 stack of 4 switches that was installed about 2 years ago. Recently I was doing some work on the switch and realized that I am unable to save the config. I amobviously concerned that if the power fails or the switch reboots I will be reconfiguring it and that is not something I am interested in doing!
[code]...
View 1 Replies
View Related
Dec 21, 2011
I am trying to assign a static ip and default gateway to my LAP through the CLI, but after I reboot it, I lose the config and it reverts back to dhcp. Is there any command to save the config to the AP through the CLI? I've tried all I can think of (i.e. wr mem, copy run start, etc...) and have looked throught the available commands but cannot figure out a way to do it..
View 6 Replies
View Related
Sep 19, 2012
I know there were a few post about users losing their access point config after a power loss to the ap. I wanted to share that I can confirm and reproduce this same issue with a number of access points that I have. I opened a tac case and will update this tread as the case progresses.
Wlc 5508
Ap 1242
7.0.220.0
View 3 Replies
View Related
Oct 26, 2011
I have several AP541 (on different site locations) which I have currently configured for WPA enterprise using windows 2008 as the Radius server. This works fine for staff members who use the wireless when roaming around the offices.
I would also like to setup another VAP for guests to allow them to access our internet but nothing else on the network. I was wondering what approach would be the best one to adopt to achieve this. Would I be best to setup a WPA Personal VAP and allow guests to access the wireless this way. Or is there a better approach? If we did adopt this approach I presume this would mean that we have to log onto each AP in turn and then change the WPA key on each one everytime we decide to change the key? Or is there some clever software I could use to change them all in one go.
View 0 Replies
View Related
Jan 3, 2013
my Cisco ASA 5510 doesn't save the configuration to the disk.
View 1 Replies
View Related
Apr 16, 2013
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies
View Related
Feb 27, 2013
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies
View Related
Apr 20, 2012
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies
View Related
Nov 1, 2012
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies
View Related
Aug 29, 2009
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
View 3 Replies
View Related
Jul 9, 2006
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies
View Related
Jan 17, 2013
I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies
View Related
Dec 14, 2011
Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies
View Related
Jul 3, 2012
I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies
View Related
Apr 25, 2011
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
View 3 Replies
View Related
Aug 25, 2011
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies
View Related
May 10, 2013
I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
View 1 Replies
View Related
May 1, 2012
Is it possible to configure WRT120n as an access point?
View 1 Replies
View Related
Apr 6, 2011
I have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies
View Related
Feb 10, 2012
I have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies
View Related
Feb 4, 2013
We currently have some LAP1242AG AP's meshed together inside our building.The owner (without consulting IT) was able to aquire some LAP1510AG's that he want's to deploy for outdoor use.Can they be meshed into our current network without having to cable one of the 1510's to the network?
View 1 Replies
View Related
Mar 7, 2013
Did you meet this issues that the remote site (US) AP 1242 always connect to our site(ASIA) WLC 5508 (maybe some DHCP configure caused when troubleshooting, right nowDHCP back to normal. only enable vendor and option 43 for 1262 and 3602, no option 43 for 1242), but now we cannot block these AP1242 to join our site 5508 WLC. even I reset the 1242 AP to default configure from WLC GUI and CLI , but it's still there in a mins.
Since in our site Core SW, Router cannot find these AP mac address, and also those AP not the IP address in the WLC GUI and CLI .
View 6 Replies
View Related
Jan 16, 2013
I have some LAP1242 which by mistake were bought for Mesh. I am trying to convert them to LWAPP so what I did first was to convert them to Stand Alone then to LWAPP but I cannot get the AP to join the WLC and sends several error logs.
I attached some logs taken from AP and WLC so that you can figure out what's going on.
I wonder if I have to remove anything from flash either on SA or LWAPP mode (I know that in some cases you have to delete privete-config in order to avoid the AP taken previous configurations). By the way I think I had never seen this c1240-k9w8-mx.124-25e.JA2 on an AP IOS before, I wonder if it has to do with the mesh thing.
View 27 Replies
View Related
Mar 12, 2013
I have a Cisco 4402 WLC running version 4.2.112.0 controlling 20+ AIR-LAP1242AG-E-K9 access points running IOS 12.4 (10b). I'm trying to setup an additional AP as MESH. When I try to change the mode from local to bridge, on what will be the rootAP, I get a message stating that bridging is not support on this unit.
View 4 Replies
View Related
Sep 1, 2012
A refurbisched WS-C3750G-24WS-S50 that we have send to our client should support 50 LAP (the unit says WS-C3750G-24WS-S50 at the back of the unit). Also the "show version" of the 3750 says WS-C3750G-24WS-S50.
He upgraded the WLC software from 4.0 to 5.0 then to 6.0 and finally upgraded to 7.0 now claims the web-interface only shows 25 supported access-points. We never checked the cli from the WLC before the upgrade.
Also he uploaded a old config file from a other S25 intergated WLC controller .
1) What could be the reason for this issue ?
2) How does the upgrading from 25 to 50 LAP work ? Is it like the PIX/ASA with a license key ?
3) When you upgrade the WLC sofware you only use a piece of universel code like the IOS right ?,can it cause a integrated WLC to loose the support for the 50 LAP ?
4) Can you use a config file from a S25 with out issues ?
5) What part-ID do we need to purchase when we want to upgrade a S25 to a S50 ?
View 6 Replies
View Related
Jul 23, 2012
The access point is reply when I ping it from WLC. But until know it can't join, even discovery packet isn't arrive in WLC.
WLC software version = 6.0.199.4
Management interface address = 192.168.120.10 /24
Model = 5508
Access point software = 1240 Software (C1240-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1) AP Model = cisco AIR-LAP1242G-E-K9 Interface address = 192.168.121.151
View 19 Replies
View Related
Apr 17, 2012
If i connected the latop to brand new out of the box ASA 5505 through consloe cable and i have a config file on this laptop from other ASA5505, is there anyway i can upload that config file into startup-config of this new ASA5505 through console cable, without using TFTP or FTP?
View 5 Replies
View Related
Nov 15, 2009
I have a Cisco 2811 router and when I turn of the router the running config is lost. I have to the following to get the router running of the start-up config settings.
router#copy start-up running-config
View 9 Replies
View Related
Oct 6, 2011
Any sample config for a remote access VPN on a Cisco Catalyst 6509 (with VPN mod).? Been searching just cant find one!
View 1 Replies
View Related
