Cisco Wireless :: How To Block LAP1242 AG Connect WLC
Mar 7, 2013
Did you meet this issues that the remote site (US) AP 1242 always connect to our site(ASIA) WLC 5508 (maybe some DHCP configure caused when troubleshooting, right nowDHCP back to normal. only enable vendor and option 43 for 1262 and 3602, no option 43 for 1242), but now we cannot block these AP1242 to join our site 5508 WLC. even I reset the 1242 AP to default configure from WLC GUI and CLI , but it's still there in a mins.
Since in our site Core SW, Router cannot find these AP mac address, and also those AP not the IP address in the WLC GUI and CLI .
View 6 Replies
ADVERTISEMENT
Jan 16, 2013
I have some LAP1242 which by mistake were bought for Mesh. I am trying to convert them to LWAPP so what I did first was to convert them to Stand Alone then to LWAPP but I cannot get the AP to join the WLC and sends several error logs.
I attached some logs taken from AP and WLC so that you can figure out what's going on.
I wonder if I have to remove anything from flash either on SA or LWAPP mode (I know that in some cases you have to delete privete-config in order to avoid the AP taken previous configurations). By the way I think I had never seen this c1240-k9w8-mx.124-25e.JA2 on an AP IOS before, I wonder if it has to do with the mesh thing.
View 27 Replies
View Related
Mar 12, 2013
I have a Cisco 4402 WLC running version 4.2.112.0 controlling 20+ AIR-LAP1242AG-E-K9 access points running IOS 12.4 (10b). I'm trying to setup an additional AP as MESH. When I try to change the mode from local to bridge, on what will be the rootAP, I get a message stating that bridging is not support on this unit.
View 4 Replies
View Related
Sep 1, 2012
A refurbisched WS-C3750G-24WS-S50 that we have send to our client should support 50 LAP (the unit says WS-C3750G-24WS-S50 at the back of the unit). Also the "show version" of the 3750 says WS-C3750G-24WS-S50.
He upgraded the WLC software from 4.0 to 5.0 then to 6.0 and finally upgraded to 7.0 now claims the web-interface only shows 25 supported access-points. We never checked the cli from the WLC before the upgrade.
Also he uploaded a old config file from a other S25 intergated WLC controller .
1) What could be the reason for this issue ?
2) How does the upgrading from 25 to 50 LAP work ? Is it like the PIX/ASA with a license key ?
3) When you upgrade the WLC sofware you only use a piece of universel code like the IOS right ?,can it cause a integrated WLC to loose the support for the 50 LAP ?
4) Can you use a config file from a S25 with out issues ?
5) What part-ID do we need to purchase when we want to upgrade a S25 to a S50 ?
View 6 Replies
View Related
Jul 23, 2012
The access point is reply when I ping it from WLC. But until know it can't join, even discovery packet isn't arrive in WLC.
WLC software version = 6.0.199.4
Management interface address = 192.168.120.10 /24
Model = 5508
Access point software = 1240 Software (C1240-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1) AP Model = cisco AIR-LAP1242G-E-K9 Interface address = 192.168.121.151
View 19 Replies
View Related
Feb 4, 2013
We currently have some LAP1242AG AP's meshed together inside our building.The owner (without consulting IT) was able to aquire some LAP1510AG's that he want's to deploy for outdoor use.Can they be meshed into our current network without having to cable one of the 1510's to the network?
View 1 Replies
View Related
Nov 18, 2011
I have 2 Air-Lap1242 that wont save their config after reboot. They are managed by a WLC (4404) and it all seems pretty fine and dandy, but when i reboot them, they dont want to save anything.I am setting them up as bridges (mesh), and it works until i reboot them, then I have to do it all over again.Using CLI to type in "write mem" or "copy running-config startup-config" only results in.
View 1 Replies
View Related
Jan 6, 2013
I have 2 Air-Lap1242 that wont save their config after reboot. They are managed by a WLC (4404) and it all seems pretty fine and dandy, but when i reboot them, they dont want to save anything.
I am setting them up as bridges (mesh), and it works until i reboot them, then I have to do it all over again.Using CLI to type in "write mem" or "copy running-config startup-config" only results in: "Building configuration... [OK] -> NVRAM Verification Failed".
View 8 Replies
View Related
Jun 20, 2011
I have 2 routers, one is a cisco 800 series router and the other just a plain WRT54G router. I have a block of 5 IPs. I have configured both routers with their own external ip addreses. Both routers can be used to connect to the internet. I can ping the cisco 800 router from the WRT54G router, but I can't ping the external ip of the wrt54G router from the 800 series router. I've checked the firewall, and acls, but I can't seem to find the right setting. I was also thinking that maybe it was something with the routing, but that didn't work either.
View 1 Replies
View Related
Nov 14, 2011
I have a Dlink DIR-615 wireless router. Without re-setting or changing the password I want to block my neighbour from using it as he knows my password
View 19 Replies
View Related
Apr 6, 2013
Currently have a Cisco Linksys EA3500 Smart Wi-Fi wireless router. Is there a possible way to prevent a computer or device to connect to the network, without making it obvious? Like to make it seem like there is an issue with the computer. Do not want to hide SSID, or block internet access. I've tried blocking internet access, but it displays on the computer that the internet has been blocked, which makes it obvious.
View 5 Replies
View Related
Dec 20, 2011
I have the Linksys WRT610N wireless router and would like to know if it is possible to block all domains ending in .XXX? The access restrictions let you type in a 'specific' URL, but using a generic domain name doesn't seem to work. I basically want to block all access to any URL that ends in .XXX.
View 5 Replies
View Related
Feb 13, 2013
Query regarding the Cisco WRVS4400N and Valet M10 routers. How to block the web interface (router login page) from wireless accessibility?
-Our Business is a hotel, so untrusted intruders are our guests.
-Our ISP seeks hotspot methods that we cannot implement.
-Our only solution is routers and an AP to extend internet wirelessly.
the login page or configuration page of the router is always accessible via the gateway address.if the gateway is 192.168.1.1, then a guest can just enter this address and try to guess the password. hacking tools add to the problem.the LAN is working but it is not of certification standards.I seek a way to block wireless access to the gateway login page or physical access only.
View 1 Replies
View Related
Sep 2, 2012
how can i block local server ip address in WAP321?I set captive portal web page and user accounts for guests but I still can map into my local server once the guest account is log in to CP.
View 1 Replies
View Related
Sep 25, 2011
All of my clients are accessing internet through Netgear wireless router. From the router's "Block Sites" option, I've inserted all of the IP address of facebook & this was working fine.
View 9 Replies
View Related
Jan 7, 2008
how to block uTorrent on the WRT54G router??? My roommate is killing my internet speed and he already had his last warning so i need to block torrents on my router
View 9 Replies
View Related
Jul 6, 2011
I want to prevent a wired pc with a static ip from accessing the internet on an e1200 router, but the computer does not show up in the list under "parental controls". I have tried adding it to the dhcp reservation table manually, but it still does not show up. There are, however, several unspecified "network devices" on the list. How can I do this?
View 7 Replies
View Related
Jan 24, 2012
not being able to block websites like facebook and youtube on the router.
View 4 Replies
View Related
Oct 28, 2011
Im using a linksys e 2000
Is there a way to block more than 4 websites, and 4 keywords?
View 4 Replies
View Related
Feb 22, 2011
How is it possible to block facebook (or other sites) on WRT610N router, given that I have already set up Internet Access restrictions based on day/hour ?
View 9 Replies
View Related
May 7, 2012
I am attempting to block Facebook on a WRT160N firmware v3.0.00. I have a successful policy that blocks edit.com for instance and attempted to add url... I don't want to add keyword blocking as multiple news articles are in regards to Facebook. We simply do not want the Facebook website allowed. I tested the other policies on a network-wide setting, applying it to all IPs successfully, added Facebook to them and it goes right around the block. My guess is that Facebook is most likely designed to make it purposely difficult to block.
I went through the recent articles in search, but they primarily dealt with incorrect application of the policy (spec'ing MAC, or IPs), which isn't the case here. Eventually I will apply the policies to specific Macs, but I want them to work first.
View 2 Replies
View Related
Nov 7, 2011
I have a Cisco E3000.My roommate is using our internet connection (in fact mine) to donwload on BitTorrent networks. I could block BitTorrents urls, but she could dowload the torrent file from another connection and do the download with my connection. So I forgot that way.I could also block ports... but she could change the ports of the BitTorrent network...
View 7 Replies
View Related
Nov 8, 2009
I've been keeping an eye on my IPS report tab lately and have been watching a large number of ICMP_SMURF and DOS attacks originating from chinese ip address's. I know I can probably block the offending ip's through the ip based acl tab in the firewall settings, but I'm kind of a newbie how I can block certain ip's from touching my router?
View 3 Replies
View Related
Mar 2, 2011
Admins could you move this over to Linksys Support, just noticed it's in the wrong place
View 5 Replies
View Related
Feb 14, 2012
How can I block certain websites in my E1200 router? I badly need it...
View 3 Replies
View Related
Feb 2, 2010
I use two wlc 4400 (4.2.x version) with a mobility domain and one ssid, both wlc are connected to a cisco l2 switch infrastructure. On the wlc I use the p2p blocking action 'drop' [URL] to isolate the clients from each other. Does only unicast traffic is blocked or also multicast and broadcast traffic like arp requests?Concerning blocking p2p traffic of clients connected to the same ssid but different controllers I found the following statement in the LAP FAQs [URL]
Q. In autonomous APs, Public Secure Packet Forwarding (PSPF) is used to avoid client devices associated to this AP from inadvertently sharing files with other client devices on the wireless network. Is there any equivalent feature in Lightweight APs?
A. The feature or the mode that performs the similar function of PSPF in lightweight architecture is called peer-to-peer blocking mode. Peer-to-peer blocking mode is actually available with the controllers that manage the LAP. If this mode is disabled on the controller (which is the default setting), it allows the wireless clients to communicate with each other through the controller. If the mode is enabled, it blocks the communication between clients through the controller. It only works among the APs that have joined to the same controller. When enabled, this mode does not block wireless clients terminated on one controller from the ability to get to wireless clients terminated on a different controller, even in the same mobility group.
what's the best practise to prevent this inter wlc client traffic? I already read about using acls on the wlc dynamic interfaces, or private vlans on the l2 switch vlans where the dynamic interfaces are connected to. Is it allowed to completely isolate the wlc from each other on these dynamic interfaces with acls or private vlans or do the wlc need to see each other on this interfaces (e.g. heart beat)?
View 19 Replies
View Related
Jan 7, 2012
I'm trying to block two URL's over the entire network via my E4200. I'm having a heck of a time doing this, I loginto my router via the browser (the web setup) (because I think Cisco Connect on the Mac is about the worst software ever written.) And I go to the Access Restrictions page. There I understand I'll have to use the Internet Access Policy pane to make some more advanced settings than the Parental Control.
I enter a name for my rule, so far so good. Enable it. Go to the applied PC page. Open the page to enter MAC adresses and IP's. I go to the IP Address Range field and entere in the box numbered 01; 192.168.2.2 to 192.168.2.51 which in my case is the enitre network. Save the setttings and close that window.
I don't set Access Restriction to deny becasue that seems to block the entire network.
So I go the the Website Blocking by URL Address option and enter the URL I want to block.
I don't do anything wiht the the Blocked Applications since I don't want to block a specific service or application. So I click Save Settings.
And yet when I go to the URL I want to block it doesn't work! [URL]
View 9 Replies
View Related
Feb 2, 2013
i got an E4200 V2 and it is updated to Linksys Smart Wifi firmware.. Is it possible to block a specific public IP address?
View 4 Replies
View Related
Mar 12, 2013
I have an E2500 wireless router and I am trying to block some incoming IP addresses. I'm trying to prevent a certain ISP from throttling my access on certain websites. I can do it on individual computers but we have a bunch of devices on this network
View 1 Replies
View Related
Mar 14, 2012
how to setup WRT54G for blocking all unwanted websites for users. When tried to configure Website under Access Restrictions tba, it accepts. However it doesn't block.
View 1 Replies
View Related
Feb 10, 2011
I'd like to block all websites except a handful. how can i do this?
linksys wrt54g
View 5 Replies
View Related
Feb 24, 2012
Is there a way to block a range of IP addresses in the E2500? Like parental controls but with IP addresses instead of URL..
View 2 Replies
View Related
Apr 28, 2013
Region : Others
Model : TL-WR740N
Hardware Version :
Firmware Version : 120320
ISP : connect communication
HOW CAN I BLOCK USER FROM MY ROUTER WHO USES WIRELESS WITHOUT CHANGING PASS BECAUSE I WANT HIM TO KNOW PASSWORD BUT HE COULD NOT CONNECT
View 1 Replies
View Related
