The access point is reply when I ping it from WLC. But until know it can't join, even discovery packet isn't arrive in WLC.
WLC software version = 6.0.199.4
Management interface address = 192.168.120.10 /24
Model = 5508
Access point software = 1240 Software (C1240-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1) AP Model = cisco AIR-LAP1242G-E-K9 Interface address = 192.168.121.151
I have some LAP1242 which by mistake were bought for Mesh. I am trying to convert them to LWAPP so what I did first was to convert them to Stand Alone then to LWAPP but I cannot get the AP to join the WLC and sends several error logs.
I attached some logs taken from AP and WLC so that you can figure out what's going on.
I wonder if I have to remove anything from flash either on SA or LWAPP mode (I know that in some cases you have to delete privete-config in order to avoid the AP taken previous configurations). By the way I think I had never seen this c1240-k9w8-mx.124-25e.JA2 on an AP IOS before, I wonder if it has to do with the mesh thing.
I get the following errors when a new 2600 series AP tries to join a 5500 series WLC:
*Apr 10 11:44:52.747: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Apr 10 11:44:53.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.0.0.9 peer_port: 5246
[Code].....
10.0.0.9 is the management interface IP of the WLC. The primary-base is set manually due to the fact that we have several WLCs in place but only 1 is s 5500 series. The other ones are 4400 series WLCs. The new 2600 APs only can join a 5500 WLC afaik. The WLC runs 7.4.100.0
are there any AP models which support 5500 series and dont support 4400 series. Actually we are looking to get some new AP with higher bandwidth and External Antenna How to differentiate between AP models with clean air feature supported and not
View 5 Replies View RelatedI have this version Ap "c1200-rcvk9w8-tar.124-21a.JA2" and a WLC 5500. When i connect the ap to the network i can ping from ap to wlc and the wlc to ap, but the proccess of lwapp messages give errors on the Ap when the Ap try to download the image from wlc and could not join the wlc. why this could be? this is the info of the wireless lan controller.
View 6 Replies View RelatedThe Release Notes for 7.0.116.0 of WLC 5500 has a table which title is "Client Type", and it shows wireless adapters. My question is,
what kind of customer means? Wireless clients or clients for an specific application? If it was the first option, does it mean tha just this adapters could connect to my wireless network?
We have the ASA firewalls in our environment - two 5510's and one 5520.Our 5510's are currently used in our production environment and the 5520 is our firewall for pre-production and support personnel. My question is about the AnyConnect VPN licenses we have. Currently we have 100 seats for AnyConnect on our production ASA's, but we'd like to see if we can move half of these to the 5520 ASA?
View 1 Replies View RelatedSince the 5500X series firewalls use a software IPS SSM that is set up differently from the old ones, I am a little confused on the initial setup.
[URL]
we see a proposed setup for L3 management of the IPS
interface GigabitEthernet0/0
nameif outside security-level 0
ip address 203.0.113.1 255.255.0.0
[Code].....
: %DATACORRUPTION-1-DATAINCONSISTENCY: unterminated string in buffer of length 129, counted: 129 -Traceback= 4027CB2C 402B1E88 4052884C 40528A48 40528D08 40529188 40529358 403247E8 403247D4
Cisco Internetwork Operating System Software
IOS (tm) C5RSM Software (C5RSM-ISV-M), Version 12.2(46), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Thu 26-Apr-07 19:41 by pwade
Image text-base: 0x40010948, data-base: 0x410F41D0
[code]....
Our requirement with that appliance is to do URL blocking and filtering.Are there any other options we can consider or is it SaaS only. Would have preferred Trend Micro, but don't this is possible with this appliance.Will content security be offered on the Cisco ASA 5500-X Series?At this time, content security services are not supported on the Cisco ASA 5500-X Series appliances. However, the ASA 5500-X Series Cisco Cloud Web Security ready. Cisco Cloud Web Security provides content security as a cloud-based software as a service (SaaS).
View 1 Replies View RelatedI bought a 5500 series ASA and SecPlus license for example. Suddenly my ASA hardware got broken and changed for a new one. What about my old license? How i could activate this license on new ASA?
View 2 Replies View RelatedI understand that Cisco have at long last provided a facility to separate HTTP web authentication from HTTPS WLC management on WLC code 7.2.x for the new 5500 series WLCs.
My question is does Cisco intend to provide the same much needed functionality on the 4400 series WLCs that are running 7.0.x code? I was looking through the release notes for v7.0.235.3 code and that did not seem to mention this functionality. I know we can get around the problem by purchasing an SSL certificate so that guest users with web authentication do not have to see the same security warning each time they log in but the idea to separate the HTTP web authentication from HTTPS WLC management seems so much simpler.
I tried looking in ASA documentations but unable to find out that how many IPSec Tunnels can be terminated to an ASA cluster. I have 5545 running only two IPSec Tunnels so far but need to terminate 18 sites all up and would like to confirm how many tunnels we could terminate? Is there a limitaion to it?
View 2 Replies View RelatedWe are working with a contractor to upgrade our network, and I heard from them that the 5596/5548 might not need the Layer 3 module for our inter-VLAN routhing. They have yet to give me an answer.
We do have a few static routes on our current layer-3, core switch too.
Did you meet this issues that the remote site (US) AP 1242 always connect to our site(ASIA) WLC 5508 (maybe some DHCP configure caused when troubleshooting, right nowDHCP back to normal. only enable vendor and option 43 for 1262 and 3602, no option 43 for 1242), but now we cannot block these AP1242 to join our site 5508 WLC. even I reset the 1242 AP to default configure from WLC GUI and CLI , but it's still there in a mins.
Since in our site Core SW, Router cannot find these AP mac address, and also those AP not the IP address in the WLC GUI and CLI .
I have a Cisco 4402 WLC running version 4.2.112.0 controlling 20+ AIR-LAP1242AG-E-K9 access points running IOS 12.4 (10b). I'm trying to setup an additional AP as MESH. When I try to change the mode from local to bridge, on what will be the rootAP, I get a message stating that bridging is not support on this unit.
View 4 Replies View RelatedA refurbisched WS-C3750G-24WS-S50 that we have send to our client should support 50 LAP (the unit says WS-C3750G-24WS-S50 at the back of the unit). Also the "show version" of the 3750 says WS-C3750G-24WS-S50.
He upgraded the WLC software from 4.0 to 5.0 then to 6.0 and finally upgraded to 7.0 now claims the web-interface only shows 25 supported access-points. We never checked the cli from the WLC before the upgrade.
Also he uploaded a old config file from a other S25 intergated WLC controller .
1) What could be the reason for this issue ?
2) How does the upgrading from 25 to 50 LAP work ? Is it like the PIX/ASA with a license key ?
3) When you upgrade the WLC sofware you only use a piece of universel code like the IOS right ?,can it cause a integrated WLC to loose the support for the 50 LAP ?
4) Can you use a config file from a S25 with out issues ?
5) What part-ID do we need to purchase when we want to upgrade a S25 to a S50 ?
We currently have some LAP1242AG AP's meshed together inside our building.The owner (without consulting IT) was able to aquire some LAP1510AG's that he want's to deploy for outdoor use.Can they be meshed into our current network without having to cable one of the 1510's to the network?
View 1 Replies View RelatedI have 2 Air-Lap1242 that wont save their config after reboot. They are managed by a WLC (4404) and it all seems pretty fine and dandy, but when i reboot them, they dont want to save anything.I am setting them up as bridges (mesh), and it works until i reboot them, then I have to do it all over again.Using CLI to type in "write mem" or "copy running-config startup-config" only results in.
View 1 Replies View RelatedI have 2 Air-Lap1242 that wont save their config after reboot. They are managed by a WLC (4404) and it all seems pretty fine and dandy, but when i reboot them, they dont want to save anything.
I am setting them up as bridges (mesh), and it works until i reboot them, then I have to do it all over again.Using CLI to type in "write mem" or "copy running-config startup-config" only results in: "Building configuration... [OK] -> NVRAM Verification Failed".
Can Controller 4400 series work with Aironet 3600 series?
View 5 Replies View RelatedWhat's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?
View 10 Replies View Relatedwhy I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies View RelatedMy Draytek 2710 just dies after 2 years so I was looking for something a little more reliable and noticed the spec of the SRP527W-U.I take it with only one antenna and reading a couple of past discussions, the wireless will only manage n-lite as some people call it i.e. 150Mbps, and not the full 300? Oh, and are the ports still only 100M and not Gig?I know the 547 would tick both these boxes but we are talking twice the price. How does the quality and logevity of the SRP500 series compare to the RV series (which would need an adsl modem) or the Linksys boxes?
View 1 Replies View RelatedDoes AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9 Access Point? How can I check this?
View 1 Replies View RelatedI am new to Cisco wireless solution and would like to ask how to add the AP to the WLC properly. All Cisco 1041 and Cisco 2500 WLC are new. I connect those AP and WLC to the switch without any VLAN tag and the AP can gain the IP address from our DHCP correctly. However, the AP 1041 could not join the WLC successfully.
WLC: Cisco 2500
IP Address: 192.168.1.225
version: 7.4.100.0
Our offcie use WLC2100 Series controller with AIR-LAP1031 and successfully join and running. Now i am trying to replace one ap with AIR-LAP1041N and join with WLC, but i can't and below the error message generate:
[code]....
I am trying to set up a Wireless network a WLC hosted on an SRE module in a 2911 router. I think i have most of my bases covered but there is still one problem.
My LAP1131AG AP's won't join the controller, on the AP im am seeing this:
Translating "CISCO-LWAPP-CONTROLLER.test.local"...domain server (192.168.250.10) [OK]
[Code].....
But to my knowledge an LWAP AP schould be able to join a CAPWAP WLC
WLC software 7.2.103.0
1. first problem: AP1252 can´t join on WLC. MAC was add on mac filter properly.
170Mon Apr 9 15:37:32 2012Mesh Node '2c:3f:38:be:53:ef' failed to join controller, MAC address not in MAC filter list.171Mon Apr 9 15:37:32 2012AAA Authentication Failure for UserName:2c3f38be53e0 User Type: WLAN USER172Mon Apr 9 15:37:32 2012Coverage hole pre alarm for client[1] 40:a6:d9:ef:87:68 on 802.11b/g interface of AP 2c:3f:38:bf:0c:80 (AP2c3f.38bf.0c80). Hist: 46 7 5 4 2 1 0 0 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0173Mon Apr 9 15:37:32 2012Coverage hole pre alarm for client[1] 8c:7b:9d:05:a0:67 on 802.11b/g interface of AP 2c:3f:38:bf:0c:80 (AP2c3f.38bf.0c80). Hist: 50 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0174Mon Apr 9 15:37:30
[code]....
Several APs can´t join on WLC and all are added on MAC filter, but they are showing this messages.
2 . Second problem.: Operational Status = UNKNOWN
Some Access Point are in UNKNOWN status. I tried but I can´t do the reboot. I can access Web config the APs using WLC, but when I applied the reset, it wasn´t working properly.
I'm new in installing WIFI, I have WLC 2504 using 7.4.100.0. I have AP 1600 (AIR-CAP1602E-E-K9)
I installed the WLC and AP in a cisco poe switch, wlc and ap are in the same subnet and can ping ap from WLC, but the AP cannot join the wlc. i have this error message
(Cisco Controller) >show ap join stats detailed 00:06:f6:d6:03:f0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
I have converted ap 1131 from autonomous to lwapp successfully by using upgrade utility tool but the AP does not join the WLC 2106. I can see it as a neighbor on the switch with no IP address.
View 19 Replies View RelatedMy WLC running 6.0.182.0 suddenly could not accept more than 47 APs! Ihave a 1240 trying to join but failed with no obvious reason (no special errors in debugging).
I unplugged one of the joined and the first one joined!! I replugged the second one but could not join!! I unplugged the first one and replugged the second one: the second joined the controller but the first could not associate again!
I have a 4400 WLC for 100APs running the 7.0.98.0software version. Now, only 48 APs are joined, and the WLC dont accept new joins. The log below are from my WLC but appear for all others APs:
%LOG-6-Q_IND: spam_lrad.c:1440 Discarding discovery request in LWAPP from AP 00:3a:98:ae:e3:f0 supporting CAPWAP%LWAPP-6-CAPWAP_SUPP_VER: spam_lrad.c:1440 Discarding discovery request in LWAPP from AP 00:3a:98:ae:e3:f0 supporting CAPWAP%CAPWAP-3-TX_ERR: capwap_ac_sm.c:1966 Failed to transmit discovery response to AP 00:3a:98:ae:e3:f0%CAPWAP-3-ENCODE_ERR: capwap_ac_sm.c:2269 Failed to encode Discovery (code)