I have a problem in join my ap1130ag in my wlc 2504 i activate dhcp internel (172.19.1.50 ----> 172.19.1.60) in wlc and this wlc affected address for ap1130ag (172.19.1.51) wlc and ap1130ag is connected with switch 2960 (port 17,18) this port the switche is configured in trunk mod allowed all vlan then my wlc not detected ap1130ag?
I have WLC 2504 with 184.108.40.206 software version , & 2 different LWAP 1262n & 1231G with "c1200-rcvk9w8-mx.124-21a.JA" Image.The 1262n is joined to the to the controller and working fine but the 1231G it can't join the controller , the controller says "Join request received from an unsupported AP" !!i will attaches the logs for this AP.
This is a new setup and has not worked yet. I have multiple 3602 APs and one 2504 Controller. I thought initially I could plug-in an AP into one of two POE Ports on the 2504. During debug mode I see that it has low power, was suprised that the 2504 switch can't fully power the AP? Is this correct?Anyways I have another POE switch that I am using with ample power. The configuration for my wireless is that it will be completely segmented off of my internal network as this is for guest access. So DNS servers are external so I cannot create host entries for the AP to discover the controller. With that being said I believe that is just one way for the discovery process to happen. I have my controller management interface and DHCP scope on the controller on the same subnet plugged into the same POE switch. The AP does seem to get a DHCP address and I can ping the controller from the AP. I cannot get any further then that. I will not join the controller and the radios get disabled. I get messages such as "discovery response from MWAR is rejected. I will post a debug log of the AP and its bootup process. This is new equipment so I would assume the firmware is somewhat up-to-date and the 3602 AP is somewhat the latest model.
If I ping the AP address from a computer in the *same subnet*, I get a perfect 0% packet loss. If I ping the AP address from a computer in ANY *other subnets*, I get about 50% packet loss. If I ping anything else *other than this single AP*, to and from any other subnets, I get a perfect 0% packet loss.
Only packets orginating or sent to the AP from other subnets are getting lost.To me it looks like there is something wrong with the routing table of the AP, as if some packets were not properly returned ?
I have a few AIR-AP1242-E-K9 AP that I have upgraded to LWAPP, after the upgrade the AP's don't join the controller. But some AIR-AP1232AG-E-K9 on the same site joins without any issues.The controller is: AIR-CT2504-K9, SW: 220.127.116.11. [code]
I have an allready configured WLC 2504 running in the network. Every LAP i add to the network joins imidiatly to the Controller. But not the AP1121G AP. It fails the Handshake everytime and the Controller shows me an failmessage at the statistics in the GUI. [code]
I want to join the AIR-AP1121G-E-K9 LAP to an 2504 WLC with software release 7.4.x .In the compatibility matrix i saw that it's just possible if the WLC has the software version of 7.0.x.So my questions are:
1. Why it's needable to upgrade the WLC from 7.0.x to 7.4.x?
2. Is there any possibility to join the AP1121G to an 2504 WLC with 7.4.x version?
3. What's the difference between the releases 7.0.x and 7.4.x
I am new to Cisco wireless solution and would like to ask how to add the AP to the WLC properly. All Cisco 1041 and Cisco 2500 WLC are new. I connect those AP and WLC to the switch without any VLAN tag and the AP can gain the IP address from our DHCP correctly. However, the AP 1041 could not join the WLC successfully.
WLC: Cisco 2500 IP Address: 192.168.1.225 version: 18.104.22.168
Our offcie use WLC2100 Series controller with AIR-LAP1031 and successfully join and running. Now i am trying to replace one ap with AIR-LAP1041N and join with WLC, but i can't and below the error message generate:
My WLC running 22.214.171.124 suddenly could not accept more than 47 APs! Ihave a 1240 trying to join but failed with no obvious reason (no special errors in debugging).
I unplugged one of the joined and the first one joined!! I replugged the second one but could not join!! I unplugged the first one and replugged the second one: the second joined the controller but the first could not associate again!
I have a 4400 WLC for 100APs running the 126.96.36.199software version. Now, only 48 APs are joined, and the WLC dont accept new joins. The log below are from my WLC but appear for all others APs:
%LOG-6-Q_IND: spam_lrad.c:1440 Discarding discovery request in LWAPP from AP 00:3a:98:ae:e3:f0 supporting CAPWAP%LWAPP-6-CAPWAP_SUPP_VER: spam_lrad.c:1440 Discarding discovery request in LWAPP from AP 00:3a:98:ae:e3:f0 supporting CAPWAP%CAPWAP-3-TX_ERR: capwap_ac_sm.c:1966 Failed to transmit discovery response to AP 00:3a:98:ae:e3:f0%CAPWAP-3-ENCODE_ERR: capwap_ac_sm.c:2269 Failed to encode Discovery (code)
We have two cisco 1262 AP and a 4402 WLC, the AP cannot join the WLC. The AP gets the address from dchp
I cannot ping the AP address from the WLC, but i can ping the default gateway and other VLAN addresses.
I already read the info on the this link : [URL] Still our AP cannot join the WLC no matter what i have tried.
- VLAN setup on a Cisco 3560 48 port poe Switch - tunk configured btwn the Gi Interface and the Management physical port - WLC mode is configured for Layer 3 - AP Manager and Management are in the same Subnet - Option 43 is configured for the with the AP Manager's IP address - Opotion 60 is also configured with AP Manager's IP address - the port connected to the APs are in the AP Manager VLAN
i converted the C1310 to LAP using upgrade tool. but the AP is not able to join the controller i was not able to view SHA Key in upgrade tool, so i ran the "debug pm pki enable " on the controler to get it. i'm still not able to view SHA key.
here is the output of debug command
*spamApTask0: May 21 15:07:43.527: 88:43:e1:d1:fc:9e Received LWAPP JOIN REQUEST from AP 88:43:e1:d1:fc:9e to cc:ef:48:b3:23:ef on port '13' *spamApTask0: May 21 15:07:43.549: sshpmGetIssuerHandles: locking ca cert table
I have some LAP1242 which by mistake were bought for Mesh. I am trying to convert them to LWAPP so what I did first was to convert them to Stand Alone then to LWAPP but I cannot get the AP to join the WLC and sends several error logs.
I attached some logs taken from AP and WLC so that you can figure out what's going on.
I wonder if I have to remove anything from flash either on SA or LWAPP mode (I know that in some cases you have to delete privete-config in order to avoid the AP taken previous configurations). By the way I think I had never seen this c1240-k9w8-mx.124-25e.JA2 on an AP IOS before, I wonder if it has to do with the mesh thing.
I have a cisco AIR-LAP1262N-A-K9 and AIR-LAP1142N-A-K9, and i would like to join to Cisco WLC2106 (software version 188.8.131.52)My ap 1262N have 3 antennas externals with 7dbi of ganancy,Is possible to do it?
I have a cisco 5508 WLC and 40 cisco 360021 APs.I configured the WLC and assign the management interface IP and also configured a DHCP pool on my Cisco 4507 core switch wit option 43.But the problem that the APs connot join the WLC.
I'd WLC 2100 series and 9 access point LAP1142N .8 LAP1142N can work fine and join a capwap controller is ok but only one LAP1142 is can not . Part of LAP is AIR-LAP1142N-A-K9
Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found *Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found *Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: Dropping discovery in LWAPP. This AP model is not supported by LWAPP WLC. *Apr 2 10:52:42.284: status of voice_diag_test from WLC is false *Apr 2 10:52:52.284: %CAPWAP-3-ERRORLOG: Go join a capwap controller
I have configured a 1552, that is wired to network, as "Bridge" then "RootAP".
After reboot, I can see a MAP trying to join the network, in the "simple" logs of the controller : "Mon May 6 17:29:43 2013 Mesh Node '04:da:d2:1f:4d:6f' failed to join controller, MAC address not in MAC filter list."
As I have done for the RAP, I enter this MAC address in the MAC Filtering area under Security tab. But this action doesn't solve the problem, I continue to see this message in the controller logs !
If I open a SSH session on the RAP, I can see this block of debug messages repeat all the time : *May 6 15:29:33.163: %MESH-6-ADJ_VIDB_LINK: Mesh neighbor 04da.d21f.4d6f VIDB Virtual-Dot11Radio0 dot1x control *May 6 15:29:33.167: %LINK-6-UPDOWN: Interface Virtual-Dot11Radio0, changed state to up *May 6 15:29:34.167: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Dot11Radio0, changed state to up *May 6 15:29:43.223: %MESH-6-LINK_UPDOWN: Mesh station 04da.d21f.4d6f link Down *May 6 15:29:43.423: %MESH-6-ADJ_VIDB_LINK: Mesh neighbor 04da.d21f.4d6f VIDB Virtual-Dot11Radio0 going
When I take a look into detailled debug messages of the controller I can see this : *spamReceiveTask: May 06 17:30:44.364: #LWAPP-6-RADIUS_AUTHORIZATION: spam_radius.c:242 The system could not send join reply, AP authorization failed; AP:04:da:d2:1f:4d:6f
I don't know why the system talks about dot1x or Radius Authorization, and if this is the source of my problems. On a other hand, I can see in the debug messages that there is a 2 hours lag time between controller (correct time) and RAP (incorrect, I suppose it synchronize with the controller?)
I setup a mini wireless LAN network lab with a not for resale 2106 wireless lan controller and a sales air-lap1242ag access point. I do not have a DHCP and DNS in my lab environment. I have configured the WLC with the basic configuration using the CLI wizard, i also configured the WLC as a DHCP server for clients that will be connecting to the APs associated to the controller.
I powered up the AP and connect the ethernet port directly to the controller, the controller issued an IP address to the AP, the AP downloaded a new operating system from the controller but failed to join the controller.
I check both debug message on the controller console and the trap messages on the controller's GUI and it say the AP could not download a configuration from the controller and it is beacuse of invalid license. Below is the trap message:
Configuration Phase Statistics Requests ReceivedResponses SentUnsuccessful Request ProcessedReason For Last Unsuccessful AttemptLast Successful Attempt TimeLast Unsuccessful Attempt TimeLast Error SummaryLast AP Message Decryption FailureLast AP Connection FailureLast Error Occurred Last Error Occurred ReasonLast Join Error Timestamp
Also, I tried to log into the GUI of the AP using the both the username and password ''Cisco'' but I cannot get into the device. I can only get in through the CLI. In the CLI, almost all the commands I enter gives an error the it is disabled. I don't know what to do any more, I want to know if the access point is faulty or i am not doing the right thing.
A customer runs a 5508 WLC for quit a while. several dozens AP's are spread all over Europe an run just fine. All the AP's have a VPN based connection over an MPLS service provider, so we are using 10.x.x.x addresses only. We have upgraded to release 184.108.40.206 to support OEAP 600 and we have configured NAT in the Firewall as well a policy to support the home office AP. Everything works fine until the switch where the WLC was attached to crushed. From this moment on, all internal AP's ar no longer able to register at the WLC. A log at the console port on an AP shows that it tries to access the external (NAT) IP address. We had to remove the NAT flag to support the internal AP's.
I have a 3502i(AP_1) that will not join a 5508 WLC(WLC_1)(code 7.2.103). The 3502i(AP_1) will join 4402 WLC(WLC_2)(Code 7.0.230). I have another 3502i(AP_2) that will join the WLC_1 & WLC_2. I am using capwap discover through DNS and hard coding the primiary WLC to AP_1 & AP_2. When I debug capwap events and errors, I see the static capwap messages and replies. Both of the WLC are on the same subnet. I have defauted the AP_1 and it joins the CISCO-CAPWAP-CONTROLLER as expected. When I change the Primiary WLC to WLC_1 it goes back to the CISCO-CAPWAP-CONTROLLER. If i change the primiary WLC to WLC_2 it joins. If I change the primiary back to WLC_1 it joins WLC_2 even though it is not a secondary. I know the previous joined WLC are stored in NVRAM, so that might be why it is doing that. I can join other ap to WLC_1 just not this one.
I am trying to get one AP to join the 2106 controller, it did join once then never again!! Now all I get is: *Jan 22 11:16:22.088: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
Trying to get an lightweight AP to register with a controller, never seen this one before where the Discovery request is going out to the controller, the discovery response is coming back, but then nothing. At this point the AP should then send a JOIN request, but it just doesnt.
I am using L3 LWAPP, and have the AP statically configured. its a 1131, connecting to a 220.127.116.11 in a WISM. I have run a wireshark and can see the discovery going out, its response coming back, but then nothing (the debugs below also back this up). I have also jumped on the controller and can see the discovery responces are going out but it says no JOIN's are coming in. I'm aware this is an old version of controller but still..
I've tried many different IOS on the AP, including the one it came with in the box, other previously successful IOS and the IOS that 18.104.22.168 dishes out to its registered AP's, multiple AP hardware resets, controller reboots, tried different controllers. etc... What would cause this? Possibly something in the response? See info below:
AP LWAPP Static IP Configuration IP Address 172.18.240.244 IP netmask 255.255.255.192 Default Gateway 172.18.240.193 [Code]....