Cisco Wireless :: 1231 Doesn't Join 2504 WLC
Oct 1, 2012Converted a Cisco 1231 with the Update Tool to lightweight (used c1200-rcvk9w8-tar.124-21a.JA2.tar). It worked, but now the AP issn't joining the wlc: [code]
View 8 Replies
ADVERTISEMENT
Cisco Wireless :: 1231 AP With WLC 2504 - Compatibilty?
Jul 11, 2012I have four 1200 series AP. Part number of these AP's is AIR-AP1231G-A-K9. I am thinking to buy a new 2504 WLC with 5 AP licenses. Just wondering whether my AP's are compatible with WLC or not. These AP's are in close proxomity and start contending with each other if I configure the stand alone.
View 3 Replies View RelatedCisco Wireless :: Can't Register AP 1231 On 2504 WLC Controller
Apr 28, 2013WLC shows the next error.
AP with MAC 00:1e:13:10:40:59 (AIR-AP1231G-E-K9 ) is unknown.
I updated the AP to lightweighd firmware using upgrade tool. But upgrade tool generate the csv files empty so I had no idea about Hash key, so I resetted the APs to default values.
WLC still doesn't register them.
How Can I register the APs? The version of the WLC is 7.3.101.0
Cisco Wireless :: 2504 - AP Cannot Join WLC
Jun 10, 2013I'm new in installing WIFI, I have WLC 2504 using 7.4.100.0. I have AP 1600 (AIR-CAP1602E-E-K9)
I installed the WLC and AP in a cisco poe switch, wlc and ap are in the same subnet and can ping ap from WLC, but the AP cannot join the wlc. i have this error message
(Cisco Controller) >show ap join stats detailed 00:06:f6:d6:03:f0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
Cisco Wireless :: WLC 2504 Not Join AP1130ag?
Mar 12, 2013I have a problem in join my ap1130ag in my wlc 2504 i activate dhcp internel (172.19.1.50 ----> 172.19.1.60) in wlc and this wlc affected address for ap1130ag (172.19.1.51) wlc and ap1130ag is connected with switch 2960 (port 17,18) this port the switche is configured in trunk mod allowed all vlan then my wlc not detected ap1130ag?
View 4 Replies View RelatedCisco Wireless :: LWAP 1231G Can't Join An WLC 2504
Dec 5, 2012I have WLC 2504 with 7.2.103.0 software version , & 2 different LWAP 1262n & 1231G with "c1200-rcvk9w8-mx.124-21a.JA" Image.The 1262n is joined to the to the controller and working fine but the 1231G it can't join the controller , the controller says "Join request received from an unsupported AP" !!i will attaches the logs for this AP.
View 3 Replies View RelatedCisco Wireless :: 3602 AP Cannot Join 2504 Controller
Oct 16, 2012This is a new setup and has not worked yet. I have multiple 3602 APs and one 2504 Controller. I thought initially I could plug-in an AP into one of two POE Ports on the 2504. During debug mode I see that it has low power, was suprised that the 2504 switch can't fully power the AP? Is this correct?Anyways I have another POE switch that I am using with ample power. The configuration for my wireless is that it will be completely segmented off of my internal network as this is for guest access. So DNS servers are external so I cannot create host entries for the AP to discover the controller. With that being said I believe that is just one way for the discovery process to happen. I have my controller management interface and DHCP scope on the controller on the same subnet plugged into the same POE switch. The AP does seem to get a DHCP address and I can ping the controller from the AP. I cannot get any further then that. I will not join the controller and the radios get disabled. I get messages such as "discovery response from MWAR is rejected. I will post a debug log of the AP and its bootup process. This is new equipment so I would assume the firmware is somewhat up-to-date and the 3602 AP is somewhat the latest model.
View 3 Replies View RelatedCisco Wireless :: AIR-CAP3602I-A-K9 Cannot Join WLC 2504 - Packet Loss On WAN
May 8, 2013I have a WLC 2504 with 10 licences running 7.3.2.112.0. I have 7 AP joined from different remote sites (WAN). The other APs are 3602E.
I got a brand new 3602I that I want to join, from a remote site and I am getting these error messages and cannot join :
*Dec 21 14:35:18.859: %CAPWAP-5-DHCP_OPTION_43: Controller address x.x.x.x obtained through DHCP,
As far as I can tell, the AP seems to be loosing packets that are coming/going away from its own subnet.
AP address : 192.168.1.1 (mask 255.255.255.0)
WLC address : 192.168.2.1 (mask 255.255.255.0)
If I ping the AP address from a computer in the *same subnet*, I get a perfect 0% packet loss.
If I ping the AP address from a computer in ANY *other subnets*, I get about 50% packet loss.
If I ping anything else *other than this single AP*, to and from any other subnets, I get a perfect 0% packet loss.
Only packets orginating or sent to the AP from other subnets are getting lost.To me it looks like there is something wrong with the routing table of the AP, as if some packets were not properly returned ?
Cisco Wireless :: AIR-AP1242AG-E-K9 Unable To Join WLC 2504 After Upgrade To LWAPP
Sep 10, 2012I have a few AIR-AP1242-E-K9 AP that I have upgraded to LWAPP, after the upgrade the AP's don't join the controller. But some AIR-AP1232AG-E-K9 on the same site joins without any issues.The controller is: AIR-CT2504-K9, SW: 7.0.220.0. [code]
View 8 Replies View RelatedCisco :: AP1121 Can't Join WLC 2504
May 22, 2013I have an allready configured WLC 2504 running in the network. Every LAP i add to the network joins imidiatly to the Controller. But not the AP1121G AP. It fails the Handshake everytime and the Controller shows me an failmessage at the statistics in the GUI. [code]
View 3 Replies View RelatedCisco Wireless :: WLC4402 - AP Doesn't Join After Upgrade To 7.0.116.0
Apr 25, 2011today i upgraded our WLC4402 from 7.0.98.0 to 7.0.116.0. After the upgrade (also bootloader upgrade) the Aironet 1142 AP's do not joint the controller anymore. Error in log:*spamReceiveTask: Apr 26 11:30:46.301: %CAPWAP-3-DISC_INTF_ERR2: capwap_ac_sm.c:1468 Ignoring Primary discovery request received on a wrong VLAN (21) on interface (29) from AP ec:c8:82:ab:ed:00 Nothing changed in infrastructure. AP's are in VLAN 21, AP-Manager interface is in VLAN 21. Ap-Manager, Management Interface and Dynamic Interfaces are in PortChannel (LAG) = Interface 29.
View 8 Replies View RelatedCisco Wireless :: AP1142N Doesn't Join WLC (5508)
Dec 27, 2012My APs 1142N don't join their WLC. APs and WLC management interface are in the same vlan (WLC can ping all the APs). It is strange because it doesn't seem like they are trying to contact the WLC. What's strange is that I have other AP 1142N which joined this WLC without any problem.
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
[Code].....
Cisco :: Any Possibility To Join AP1121G To 2504 WLC With 7.4.x Version
May 21, 2013I want to join the AIR-AP1121G-E-K9 LAP to an 2504 WLC with software release 7.4.x .In the compatibility matrix i saw that it's just possible if the WLC has the software version of 7.0.x.So my questions are:
1. Why it's needable to upgrade the WLC from 7.0.x to 7.4.x?
2. Is there any possibility to join the AP1121G to an 2504 WLC with 7.4.x version?
3. What's the difference between the releases 7.0.x and 7.4.x
Cisco Wireless :: LAP1240 - H-REAP Enabled AP Doesn't Join HQ Controller
Oct 14, 2012i have configured cisco LAP1240 in H-Reap Mode for multiple branch offices with Local switching and central authentication. one of the branch's AP does not join the controller in HQ while the others are all ok. i have firewall only in HQ, i did priming first for all APs like let them join the controller and configure controller IP in high availbility, and H-Reap config and assign SSID to map with the branch local vlan. when i faced this issue first time i brought back ap and configure a static IP address for AP than recheck them again but the problem still same. since i have only one firewall in the network and also other branches joined the controller through that firewall and no issues.
View 3 Replies View RelatedHamachi Doesn't Create Or Join Network
Mar 13, 2011I've been trying to get it to work all day.When I open up Hamachi it shows the main screen with two buttons. Create a new network and Join an existing network.I've tried both but when I click create or join it doesn't do anything. Like it actually does nothing at all.Doesn't even close the window.Everything stays open and it doesn't either create or join any networks.
View 1 Replies View RelatedCisco :: WLC 2504 / Wired Equipment Doesn't Obtain DHCP Address
Apr 14, 2013I have two ethernet cards (from same equipment) that arent acquiring IP Address after instalation of WLC 2504.I dont want (yet) to disable DHCP proxy on WLC.
*DHCP Socket Task: Apr 15 18:49:04.219: 00:0a:95:XX DHCP received op BOOTREQUEST (1) (len 556,vlan 0, port 1, encap 0xec00)
*DHCP Socket Task: Apr 15 18:49:04.219: 00:0a:95:XX DHCP dropping packet (no mscb) found - (giaddr 0.0.0.0, pktInfo->srcPort 68, op: 'BOOTREQUEST')
*DHCP Socket Task: Apr 15 18:49:07.218: 00:0a:95:XX DHCP received op BOOTREQUEST (1) (len 556,vlan 0, port 1, encap 0xec00)
*DHCP Socket Task: Apr 15 18:49:07.218: 00:0a:95:XX DHCP dropping packet (no mscb) found - (giaddr 0.0.0.0, pktInfo->srcPort 68, op: 'BOOTREQUEST')
[code].....
Cisco Wireless :: AP 1231 With WLC 7.0 Connection
Aug 7, 2012At work we have some older 1231 AG model access-points and a WLC with version 7.0. I was trying to convert them to lightweight and they will not join the controller without importing a .CSV file into the WLC. I cannot figure out to import that file, I cannot find any documentation on how to add the certificate with version 7.0.
View 2 Replies View RelatedCisco Wireless :: 1231 Fail To Register To Primary WLC
Oct 29, 2011We have found that only Cisco 1231 WAP are exhibiting this behaviour. Their Primary WLAN controller is Cisco1 WLC but they fail to register to Primary WLC and fall back to Cisco2 WLC. After about 200 sec , they attempt to connect to Primary WLC once again and fail. The whole cycle is repeated every 250 seconds.
View 3 Replies View RelatedCisco Wireless :: Aironet 1231 Stand-alone Mode
Sep 12, 2012I have some old 1231 APs in the school in which I work.I would like to create a local network (no LAN, no internet, just a point to point wifi connection) managed by the access point (in DHCP).That's because we have an apple TV connected to a projector and some ipads. My idea was to put the devices locally in the same closed network for share via AIR Mirror the ipads on the apple TV.
View 3 Replies View RelatedCisco Wireless :: Failing To Add Aironet 1231 To WLC 5508
Jul 8, 2012I'm having little success migrating our older Aironet1231 to our new WLC 5508. The 1231 is currently registered as a LAP to a 4400 WLC and I'm in the process of moving away from this controller to the new one. I've pasted the output of the error messages I'm getting below. At this point, I'm stuck and not sure how to get around the "Failed to parse CAPWAP packet" error.
I'm getting these messages when I have:
debug pm pki enable
debug capwap errors enable
I initially got this error, but got passed it when I allowed SSC in the 5508 (Security -> AP Policies)
sshpmGetIssuerHandles: SSC is not allowed by config; bailing...
Now I'm getting these:
*sshpmLscTask: Jul 09 11:13:11.516: sshpmLscTask: LSC Task received a message 4
Cisco Wireless :: 1242G-E-K9 Not Seeing Other 1242s Or 1231 On Network?
Oct 31, 2011I have a problem where clients cannot roam between Cisco 1231g-e-k9 and recently installed cisco 1242g-e-k9 access points.. On looking at the CDP option on the 1231 and 1242 access points they are all aware of each other. However if I use the Network View option I see a different picture. All the 1231 access points can see each other but not see the 1242's. Network View on the1242 shows all the 1231's but none of the 1242's. The 1231 are running ver. 12.3(8)JEB and the 1242's are running ver. 12.4(21a)JA1.
View 2 Replies View RelatedCisco Wireless :: Cannot Connect To Second SSID On Aironet 1231
Apr 22, 2013I have configure my AP with to SSID (11 & 12), but I cannot connect to 12. It authenticates, and while trying to acquire IP address from 12, it fails and connects me to 11 (if I have already saved the SSID connection).
The following is my AP status:Product/Model Number:AIR-AP1231G-A-K9 System Software Filename:c1200-k9w7-tar.123-8.JEE System Software Version:12.3(8)JEE Bootloader Version:12.3(2)JA4
The SSID 12 already have 4 clients connected, And I am tring to connect a 5th one (smart phone), but cannot connect to 12, instead coneected to 11. Also tried with a laptop, but cant get the IP address, and give Limited Connectivity error.
Cisco Wireless :: Reset Aironet 1231 To Factory Default?
Sep 17, 2012I have a (old) 1231 that I would like to reuse, but no one remembers the password. how to recover a password from this model AP or how to reset the device to factory default?
View 1 Replies View RelatedCisco Wireless :: Controller Software That Supports 3600 And 1231 APs?
Dec 4, 2011Customer is interested in deploying the 3600 AP's but will not be able to replace all his 1231's, any chance there is a release between 7.0.220.0 and 7.1.91.0 that will support both AP's?
View 6 Replies View RelatedCisco Wireless :: Disable AP Mode Multicast In 1231 Series Access Point
Jan 23, 2013I have one controller 2504 and some 1200 series access points.I am using 3 SSID .I want to use two ssid in HREAP mode but HREAP mode is not showinh in access point because multicast is enabled on AP mode. see the below picture
I have disabled the multicast globally from CLI. config network multicast global disabled
disabling the multicast so that i can set the access point in HREAP mode.
Cisco :: Changing AP 1230 And 1231 From Lightweight To Autonomous
Jan 22, 2013I cannot TFTP this tar file to both 1230 and 1231 APs. Both are lightweight APs that I've wiped to the rommon mode (ap>) and I issue the command:
tar -xtract c1200/k9w7-mx.123-8.JA 10.0.0.2
And I get a error saying: "permission denied"
Notes:
The AP has defaulted to the 10.0.0.1 IP.
My laptop is set to 10.0.0.2 255.255.255.0 IP
My TFTP-Server is on and the root folder with the .tar file is in there.
ether_init, flash_init, tftp_init (these commands have been executed)
My firewall is disabled.
Cisco :: 1231 / External RADIUS Attributes For MAC Authentication
Jun 21, 2006We have a 1231 AP and a Freeradius Server.Now we are using MAc authentication.The thing is that the AP sends two parameters to the RADIUS:
User-Name = "000ff855df2e"
User-Password = "000ff855df2e"
both are the MAC of the wireless client.I want that the AP send:
User-Name = "00-0f-f8-55-df-2e"
User-Password = "mykey"
Note that the MAC is dash separated and the password is forced to the key that I want.
Cisco :: Autonomous 1231 / 1242 Radius Configuration?
Jan 12, 2011I can't seem to get the SSID RadiusTest to work properly.
Windows PC's show "Windows was unable to find a certificate to log you into the network". Macs don't authenticate either. Radius server isn't seeing any requests at all. Radius server is working because we are authenticating other things to it.
On my test 1231, IOS is 12.3(8) JEB1.
version 12.3
no service pad
service timestamps debug datetime msec
[Code].....
Cisco Switching/Routing :: 3550-24-PWR Can't Ping Aironet 1231
Oct 30, 2012I have two 1231G Aironet's that work correctly when I connect them to my Catalyst 3548XL and my 3550-48-XL switches. When I connect them to the 3550-24-PWR switch I do see them when I issue sh cdp nei det. It shows me the IP of the wireless router. But when I ping the Aironet, I do not get any replies. If I plug the Aironet into my 3548XL and ping the IP, I get 5 replies. Here is the port config on both switches:
switchporrt trunk encapsulation dot1q
switchport native vlan 100
switchport allowed vlan 1,69,100,125,200,1002-1005
switchport mode trunk
spanning-tree portfast
Here is the sh cdp nei det results:
Device ID: North_AP.mtd.home
Entry address(es):
IP address: 192.168.100.104
Platform: cisco AIR-AP1231G-A-K9 , Capabilities: Trans-Bridge
Interface: FastEthernet0/3, Port ID (outgoing port): FastEthernet0
[code]....
I have tried two versions of the IOS on the 3550PWR switch. Right now its: c3550-ipservices-mz.122-44.SE6
Cisco :: Radius Auth Fails For Some Machines After Upgrade From 1231 To 1142
Dec 9, 2012After upgrading from a 1231 autonomous to an 1142 autonomous AP some machines can no longer authenticate. AP logs show authentication failure and access reject coming from the Radius server. Radius server shows authentication failures but no specific reason. Using the same account on another machine works fine. Machine settings have been verified and if we go back to the 1231 all users authenticate fine. Below are the configs:
OLD AP:
!
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec localtime show-timezone
service password-encryption
[code]...
Cisco Wireless :: How To Join The AP To WLC2500
May 16, 2013I am new to Cisco wireless solution and would like to ask how to add the AP to the WLC properly. All Cisco 1041 and Cisco 2500 WLC are new. I connect those AP and WLC to the switch without any VLAN tag and the AP can gain the IP address from our DHCP correctly. However, the AP 1041 could not join the WLC successfully.
WLC: Cisco 2500
IP Address: 192.168.1.225
version: 7.4.100.0
Cisco Wireless :: AIR-LAP Does Not Join With WLC2100
Mar 24, 2013Our offcie use WLC2100 Series controller with AIR-LAP1031 and successfully join and running. Now i am trying to replace one ap with AIR-LAP1041N and join with WLC, but i can't and below the error message generate:
[code]....
Cisco Wireless :: LAP1131AG Won't Join WLC On SRE-ISM
Jul 10, 2012I am trying to set up a Wireless network a WLC hosted on an SRE module in a 2911 router. I think i have most of my bases covered but there is still one problem.
My LAP1131AG AP's won't join the controller, on the AP im am seeing this:
Translating "CISCO-LWAPP-CONTROLLER.test.local"...domain server (192.168.250.10) [OK]
[Code].....
But to my knowledge an LWAP AP schould be able to join a CAPWAP WLC