I have a (old) 1231 that I would like to reuse, but no one remembers the password. how to recover a password from this model AP or how to reset the device to factory default?
View 1 Replies
I have a cisco aironet 1300 series and i need to reset it back to factory default. the directions say push the mode button while the access point is off and then turn it on while the mode button is down.
View 1 Replies View RelatedHow to reset a CAPWAP AP3600 to factory default using the AP's CLI and not the controller.
View 2 Replies View Relatedi have a wrt54gl version1.1 ok so let me start from the beginning.a few months ago i left the contry so a friend of mine asked me to lent him my router. a few day`s ago i got back and got my router back. it was working fine until i got it back. the rest button won`t work. i can`t reset the router to factory default. the user name was blank and the password was admin.now it won`t let my to do that.
View 9 Replies View RelatedDue to password loss, I get to reset the E4200 to factory default in order for router re-config.After pressing the reset buttom for 10sec, the router reset. After then, I could not access the router via browser with 192.168.1.1 at URL entry. My PC IPv4 setup: 192.168.1.11; subnet=255.255.255.0.But, ping 192.168.1.1 from PC was OK without packet loss. So router was restored with 192.168.1.1 and cable connection was OK.
View 2 Replies View RelatedI was trying to do a password recovery on a 1142 AP but enable password did not reset and I am stuck
AP model is AIR-AP1142N-A-K9
Running IOS c1140-k9w7-mx.124-21a.JA1
Its autonomous so there is no controller. I renamed the config.txt file I am unable to rename or delete the private-config file. I get the message that file or directory cannot be found when i try to rename and permission denied when I try to delete it.
We have an AIR-LAP1142N-E-K9 deployed in a H-REAP setup.This AP already got the configuration from the WLC when it was deployed at a remote site.Now we moved it to another site, but it doesn't appear in the WCS and i don't see any CAPWAP debug messages on the WLC.The routing work fine between the AP and the WLC, the AP also gets an IP address from DHCP and also received Option 43 information.
Now my guess was that the AP doesn't associate with the WLC because it has the old config file and it runs in local mode(without trying to connect to the WLC).We want to reset to factory defaults because we want to delete the configuration and force the AP to get a new config from the WCS.I don't know the enable password so i had to use other methods for reseting to factory defaults.
I tried to use the information from here:[URL]I used the "MODE button":I get the following message from the console:
"button pressed for 5 seconds
process_config_recovery: set IP address and config to default 10.0.0.1"
I am trying to reset my 1522 series lightweight access point to factory default.On the box,there is no any mode button.Actually password is not set to Default and need pasword recovery on this device.If you have any experience on this lightweight access point that let me know.How I reset device to fectory default.
View 1 Replies View RelatedI have a 1142 that I purchased that needs to be set to factory defaults so that I can configure it. I do an escape at the boot sequence and I get to the
ap:
prompt, the reset instructions that Cisco provides says that I should rename the old config.txt and reboot and that I will then be able to start my reconfig. The problem is that I can't find a config.txt file in the flash space:
Directory of flash:/
2 -rwx 260 Jan 1 1970 00:04:28 +00:00 env_vars
3 -rwx 112947 Apr 1 2011 15:17:10 +00:00 event.log
5 drwx 128 Mar 1 2002 00:01:54 +00:00 c1140-rcvk9w8-mx
9 drwx 256 Apr 1 2011 14:30:32 +00:00 c1140-k9w8-mx.124-21a.JHB1
8 -rwx 5144 Mar 1 2002 00:00:27 +00:00 private-multiple-fs
I checked in the directories listed above and still found no config.txt.
My team already bought one 1800 Series router. And they setted some passwor.
Right now i am not able to login. I know the cisco password recovery method to reset the password.
Instead of password recovery method i want to try with total factory default setting.
is there is any method to do factory default without login
I have an AIR-AP521G-E-K9 and i want to reset to factory default in CLI.I tried "write erase" but dont work.I have problems with access-list and i want to desactivate access-list that i have created by web GUI.The problems now is that i can not access to my AP, no ping, no web GUI access.Access that i have is only by CLI, but access list is always blockinh all tha traffic trought my AP.How can i desactivate mac filtering, or how can i reset to factiry default
View 1 Replies View RelatedI need to reset my DLink wireless modem all over again, can't get it to recognise the router, so thought that it would need to reset to factory defaut, how can I do this. Tried just hitting reset on the router,but nothing is happening.
View 4 Replies View RelatedI have a WRV210-A V01 (Software: 2.0.1.5) router that when originally purchased I upgraded the firmware to the newest 2.0.1.5. However after the firmware upgrade the router has not worked right since. [I thought maybe the upgrade did not take, and successfully pushed the firmware 3x times]
Everytime you login to the webpage the right-side pane you have to scroll down 3x pages until you can see the settings options. It does that for everypage you visit you have to scroll down 3x pages until you can see the settings.
The wireless is sporadic and dropping connections, and now certain options like changing the "Basic Rate:" from "All' to "Default" does nothing and wont let you change it.
The main issue I have is that certain wireless settings like changing the "AP Isolation:" cause the router to reset back to factory defaults. and even trying to configure the LAN setup also randomly makes the router reset to factory default.
Unable to log in into our new ESW 540 switch because the default User ID and PW was changed. How do i restore the factory default on the switch.Can't get into the switch with CCA or explorer.
View 1 Replies View RelatedIm connecting to my firewall through the console port, and need to know how to reset it to factory defaults. I have looked around online and can not see any reference on how to do this.
View 11 Replies View Relatedi have a new 5505 and i have done a few configurations on it. When i try to reset it to the factory settings via asdm i get an error saying it could not be done. I have used config-factory-default using the cli option available in the asdm. I am using asa 8.2 and asdm 6.2. Will erasing the flash reset to factory defaults.
View 4 Replies View RelatedRecently purchased a RVS4000 Router, which included v1.1.14 firmware. Is it necessary to reset the router to Factory Default settings, after upgrading to v1.2.11, as in most of the other previous upgrades?
View 37 Replies View RelatedWhy when I try to reset Cisco ASA 5505 by pressing the button behind the hardware nothing happen? Just via software I can reset it?
I bought the hardware an year ago and I've never used, the problem that I don't have the blue cable and via software connecting to PC doesn't work.
I have a cisco 2960 that I seemed to have lost the password. Its just a test switch. I would like to know how to reset it to factory default. I have managed to get to a switch: prompt by holding in the small mode button on the front of the switch and pluging in the power but lost from here.
View 1 Replies View RelatedI reset unplug did everything according from cisco.com it didn't work.Can not go to 192.168.1.245. What next I need to do to make it work.
View 3 Replies View RelatedWhen I ran a reset to factory settings of my acer aspire one netbooks which runs windows 7 I no longer have a wireless connection option at all. I have done this before and never lost my ability to connect wirelessly. I tried to look for driver downloads but I'm not even sure what it is I need to do to recover the missing program as it was a original factory program.
View 4 Replies View RelatedI have some old 1231 APs in the school in which I work.I would like to create a local network (no LAN, no internet, just a point to point wifi connection) managed by the access point (in DHCP).That's because we have an apple TV connected to a projector and some ipads. My idea was to put the devices locally in the same closed network for share via AIR Mirror the ipads on the apple TV.
View 3 Replies View RelatedI'm having little success migrating our older Aironet1231 to our new WLC 5508. The 1231 is currently registered as a LAP to a 4400 WLC and I'm in the process of moving away from this controller to the new one. I've pasted the output of the error messages I'm getting below. At this point, I'm stuck and not sure how to get around the "Failed to parse CAPWAP packet" error.
I'm getting these messages when I have:
debug pm pki enable
debug capwap errors enable
I initially got this error, but got passed it when I allowed SSC in the 5508 (Security -> AP Policies)
sshpmGetIssuerHandles: SSC is not allowed by config; bailing...
Now I'm getting these:
*sshpmLscTask: Jul 09 11:13:11.516: sshpmLscTask: LSC Task received a message 4
I have configure my AP with to SSID (11 & 12), but I cannot connect to 12. It authenticates, and while trying to acquire IP address from 12, it fails and connects me to 11 (if I have already saved the SSID connection).
The following is my AP status:Product/Model Number:AIR-AP1231G-A-K9 System Software Filename:c1200-k9w7-tar.123-8.JEE System Software Version:12.3(8)JEE Bootloader Version:12.3(2)JA4
The SSID 12 already have 4 clients connected, And I am tring to connect a 5th one (smart phone), but cannot connect to 12, instead coneected to 11. Also tried with a laptop, but cant get the IP address, and give Limited Connectivity error.
I have two 1231G Aironet's that work correctly when I connect them to my Catalyst 3548XL and my 3550-48-XL switches. When I connect them to the 3550-24-PWR switch I do see them when I issue sh cdp nei det. It shows me the IP of the wireless router. But when I ping the Aironet, I do not get any replies. If I plug the Aironet into my 3548XL and ping the IP, I get 5 replies. Here is the port config on both switches:
switchporrt trunk encapsulation dot1q
switchport native vlan 100
switchport allowed vlan 1,69,100,125,200,1002-1005
switchport mode trunk
spanning-tree portfast
Here is the sh cdp nei det results:
Device ID: North_AP.mtd.home
Entry address(es):
IP address: 192.168.100.104
Platform: cisco AIR-AP1231G-A-K9 , Capabilities: Trans-Bridge
Interface: FastEthernet0/3, Port ID (outgoing port): FastEthernet0
[code]....
I have tried two versions of the IOS on the 3550PWR switch. Right now its: c3550-ipservices-mz.122-44.SE6
I am the owner of an Asus N53SV series laptop running windows 7 home premium. I factory reset my PC in order to have a "fresh" new year, but now I can only connect to the wireless internet in my house using the ethernet cable. When the cable is unplugged, no networks show up for my laptop. I tried going to this link: ASUSTeK Computer Inc. -Support- Drivers and Download N53SV I downloaded the first wireless driver listed...and it gave me an error that just said "error azureware wireless lan driver"....not a very informative error.
View 13 Replies View RelatedIs there any possible way to factory reset an AIR-AP1231G-A-K9 that was once attached to a WLC via SSH? I dont have physical access to it and the old WLC has long been decommissioned. I have tried the clear command but since it is in CAPWAP mode that command has been disabled. I know I can press and hold the mode button and reset it that way but I need to know if its possible through SSH to be reset. I have two that are in need of being reset in order to connect to the new WLC.
View 21 Replies View RelatedI have a used 1252 wireless AP. I can't get into it. How do I reset to factory default?
View 1 Replies View RelatedAny info on successfully resetting an light weight 1130 AP to the factory settings? I tried the method described in the doc for 1130 on how to reset 1130 AP to the default settings, but it was not successful. I tried shutdown the AP, and plug in the power while press and holding the Mode button for about 3 seconds.This AP has lost it association with the WLC, is there anyway i can reset the AP to factory default and put in the correct IP address again?
View 3 Replies View RelatedI currently have 2 cisco aironet 1121G access points. Both of which I believe had an image fail during an upgrade from autonomous mode to lightweight mode. I have tried to reset these access points as directed from Cisco's instructions. I have done a reset (amber light on the middle) and a factory restore (red light in the middle) They go through the steps to restore to factory default, however, after what I believe is an attempt to pull a dhcp address before defaulting into 10.0.0.1 ip address, the access point restarts. This is happening to both of them. After they reset and go through the series of memory tests, I am able to get all three solid green lights, they stay lit for just 15 seconds (rather than 5 minutes so that i can load a new image) I am not sure why they are behaving this way. I have tried as many different possibilities resetting with the mode button. There is no console port on this model of access points so i am unable to manage it otherwise.
View 1 Replies View RelatedI have a 3502 AP that I am attempting to set back to factory default including clearing the username and password. It is going to work off of 4400 controllers. I have read numerous documents no how to clear the config and password but so far nothing has worked. I can get it into ap: mode but not sure what to enter here. When I do a dir there doesnt seem to be any files. It will pull an IP address via the local router but cannot communicate with WLC.
View 28 Replies View RelatedHow to reset my router to factory settings so i can install it on a new computer
View 2 Replies View RelatedIused my installation cd to re-setup my linksys. I moved and used a laptop previously. Now i am at a house that has a desktop. I want to keep the desktop wired and make my laptop wired. So, when i went to re-install it said i had to reset my linksys to factory settings.
View 2 Replies View Related
