Cisco Wireless :: Cannot Connect To Second SSID On Aironet 1231
Apr 22, 2013
I have configure my AP with to SSID (11 & 12), but I cannot connect to 12. It authenticates, and while trying to acquire IP address from 12, it fails and connects me to 11 (if I have already saved the SSID connection).
The following is my AP status:Product/Model Number:AIR-AP1231G-A-K9 System Software Filename:c1200-k9w7-tar.123-8.JEE System Software Version:12.3(8)JEE Bootloader Version:12.3(2)JA4
The SSID 12 already have 4 clients connected, And I am tring to connect a 5th one (smart phone), but cannot connect to 12, instead coneected to 11. Also tried with a laptop, but cant get the IP address, and give Limited Connectivity error.
View 3 Replies
ADVERTISEMENT
Sep 12, 2012
I have some old 1231 APs in the school in which I work.I would like to create a local network (no LAN, no internet, just a point to point wifi connection) managed by the access point (in DHCP).That's because we have an apple TV connected to a projector and some ipads. My idea was to put the devices locally in the same closed network for share via AIR Mirror the ipads on the apple TV.
View 3 Replies
View Related
Jul 8, 2012
I'm having little success migrating our older Aironet1231 to our new WLC 5508. The 1231 is currently registered as a LAP to a 4400 WLC and I'm in the process of moving away from this controller to the new one. I've pasted the output of the error messages I'm getting below. At this point, I'm stuck and not sure how to get around the "Failed to parse CAPWAP packet" error.
I'm getting these messages when I have:
debug pm pki enable
debug capwap errors enable
I initially got this error, but got passed it when I allowed SSC in the 5508 (Security -> AP Policies)
sshpmGetIssuerHandles: SSC is not allowed by config; bailing...
Now I'm getting these:
*sshpmLscTask: Jul 09 11:13:11.516: sshpmLscTask: LSC Task received a message 4
View 3 Replies
View Related
Sep 17, 2012
I have a (old) 1231 that I would like to reuse, but no one remembers the password. how to recover a password from this model AP or how to reset the device to factory default?
View 1 Replies
View Related
Oct 30, 2012
I have two 1231G Aironet's that work correctly when I connect them to my Catalyst 3548XL and my 3550-48-XL switches. When I connect them to the 3550-24-PWR switch I do see them when I issue sh cdp nei det. It shows me the IP of the wireless router. But when I ping the Aironet, I do not get any replies. If I plug the Aironet into my 3548XL and ping the IP, I get 5 replies. Here is the port config on both switches:
switchporrt trunk encapsulation dot1q
switchport native vlan 100
switchport allowed vlan 1,69,100,125,200,1002-1005
switchport mode trunk
spanning-tree portfast
Here is the sh cdp nei det results:
Device ID: North_AP.mtd.home
Entry address(es):
IP address: 192.168.100.104
Platform: cisco AIR-AP1231G-A-K9 , Capabilities: Trans-Bridge
Interface: FastEthernet0/3, Port ID (outgoing port): FastEthernet0
[code]....
I have tried two versions of the IOS on the 3550PWR switch. Right now its: c3550-ipservices-mz.122-44.SE6
View 5 Replies
View Related
Nov 18, 2012
I am using a Aironet 1100 series access point (AIR-AP1142N-N-K9) with IOS version c1140-k9w7-tar.124-21a.JA1. I want to create two seperate SSID's on the access point with WEP encryption. There is no VLAN configured and i want it to be like it. Also I need to broadcast both the SSID's at the same time, so the some of my users need to login with the first SSID and the others to login through the other.
View 2 Replies
View Related
Sep 28, 2012
I configured the device manually, not even using Express Setup or Express Security setup so... it is possible I missed something.Anyway, here's the problem. Although the SSID is configured as "AP1", this SSID does not appear among available networks on the client laptop.
The connection, configured in Group Policy for the client, should actually happen automatically, based on the SSID, but since the SSID is not being broadcast, that connection is failing as well.
The Aironet does appear among the available networks as "Other Network" and if I click on "connect" I am prompted to enter the SSID -> AP1
Although, unexplicably, an error message displays (Windows cannot connect to the network, or something to that effect), the laptop *does* connect once I close that window. Network access is complete and functional - I can ping other hosts, etc..
I'd post screenshots but not knowing what setting is missing or incorrect, I'd have to print dozens. So here's the sh run output of the AP obtained via telnet (just below). This is a test network so all information is "real" (nothing changed for privacy):
Note: I even changed the hostname to "AP1" (it's still LAB1 below) but that did not resolve the problem (did not think it would).
LAB1#sh runBuilding configuration...
Current configuration : 2321 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname LAB1!logging rate-limit console 9enable secret 5 $1$9EWD$kxrbg8KxikRFypOieKiZh/!aaa new-model!!
[Code]....
View 5 Replies
View Related
Jan 25, 2012
I'd like to change the SSID name on Aironet 1200 which is currenty used by my wireless network.
View 3 Replies
View Related
Dec 22, 2009
We have multiple Cisco Aironet 1131AG devices, all wired on one Cisco L2 switch(2560) who is connected to L3 switch (3550). We assigned one VLAN for access point in L3 switch who acts as vtp server (L2 switch is vtp client). All ap's will have static ip address and all will have same SSID and no security and they will be using multiple channels (ex. 1,6,11). They will operate in 3 floor building for roaming wireless client. We won't using any wireless controller.
How to configure APs-all the same with different ip's, can we use L3 switch to create dhcp server for access points VLAN (pool for clients, and the rest for static ip for ap's)?
View 2 Replies
View Related
Apr 3, 2012
Can I configure Multiple SSID (Guest/Corporative) on Cisco Aironet 3600i AP via Cisco 2504 Wireless controller?
View 1 Replies
View Related
Sep 6, 2012
I'm facing a problem on vWLC. I configured the vWLC and Aironet 1252, I created 2 SSID with below settings.
1. WPA2 Auth 802.1X
2. Web-Auth
Inside Wireless, I configured this AP Mode as "Local", but all of the client device such as iPhone, Laptop can't find these SSID.
View 3 Replies
View Related
Jan 31, 2012
I have a "standart" settings of Cisco Aironet 1240AG with ENABLED broadcasting SSID, encryption is WPA2 (AES). I can see the wifi network (ssid) with windows system but with MAC OS 10.5 and MAC OS 10.7 also with iPhone the wifi is acting like hidden. But If I manually enter the wifi ssid and set the proper encryption the connection work normally. Also I have a separete windows partition on one MACbook and this windows 7 have no problem to see the SSID of my network. But If i Boot to the MAC OS the WIFI is "hidden" until the manually connection. (same problem on iphone, manuall connect with manually entered SSID is working well).
View 2 Replies
View Related
Mar 4, 2013
I am working on setting up a new WLAN infrastructure. I have set up different SSIDs connected to different VLANs, in the AP. I also want to use Windows NPS for authenticating users on the different SSIDs, with different authentication methods based on which SSID the user/device is connecting to. To do that, NPS needs to get the SSID, but the Aironet 1240 only sends its MAC address in the Called-Station-Id. I have read a bit about this, and found out that if I have a WLC, it will add the SSID to to the Called-Station-Id. But since we do not have a WLC, I am trying to get this to work anyway. Is it possible to modify the Called-Station-Id to include the SSID on an Aironet 1240? If not, is it possible to send the SSID as a separate attribute that can be read by the NPS?
View 10 Replies
View Related
Sep 19, 2011
I wonder if there is a way to rename an existing SSID on aironet 1142 without destroying/recreating. I tried downloading configuration/ changing name/ re-uploading however that didn't have desired effect. There doesn't seem to be a way via web-GUI.
View 3 Replies
View Related
Mar 28, 2013
We have three Access Points, two Cisco Aironet 1260 and one 1240AG. Originally, the SSID was hidden on all three AP's and users had to go to Other Networks and type in the SSID and password to access the WAN. About a few months ago, the network started broadcasting to the public. I am trying to make the SSID hidden again. I have tried going to the Security tab, choosing the SSID Manager and setting single guest mode to none but it has not worked.
View 4 Replies
View Related
Oct 21, 2012
how i can configure a second ssid for guest access in our environment. this is our network setup prior to this request: Internet----Firewall (not ASA)---ce520---C1131AG and CME router is also connecting to the ce520 switch. we only have two vlans: one for voice and two for data.
Presently, there is no vlan configured on the AP because it on broadcasting ont ssid and wireless users gets IP from a windows DHCP server on the LAN. the configuration on the ce520 switch port for the AP and other switches say access vlan is the DATA vlan which automatically becomes the native vlan for all trunk port connecting the AP and other Stiches to the network.
Now with this new requirement, i have made my research and i have configured the AP to broadcast both the production and the guest Vlans. The two vlans are 20-DATA and 60-Guest. I made the DATA vlan on the AP the native vlan since the poe switch is using the DATA vlan as native on the trunk ports. I configured the firewall to serve as DHCP server for the guest ssid and i have added the ip helper-address on the guest vlan interface on all switches while the windows server remains the dhcp server for the production DATA Vlan. I have confirmed that the AP, switches can ping the default gateway of the guest dhcp server which is another interface on the firewall. I can now see and connect to all broadcasted ssids but the problem is I am not getting IP addresses from both the production dhcp server and guest dhcp server when i connected to the ssid one at a time. My AP config is attached below.
Do i need to redesign the whole network to have a native vlan other nthan the data vlan? Does the access point need to be aware of the voice vlan? Do the native Vlan on the AP need to be in Bridge-group 1 or can i leave it in bridge-group 20?
View 1 Replies
View Related
Feb 2, 2011
i've been looking for a way to isolate clients on a Cisco Aironet 1121 on a certain SSID, and i cant find anything, tried pretty much everything i coudl remember, but since im no expert on Cisco wireless.
Quote:
Cisco IOS Software, C1100 Software (C1100-K9W7-M), Version 12.3(7)JA1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2005 by Cisco Systems, Inc.
[Code].....
View 3 Replies
View Related
Dec 17, 2012
how to change our wireless setup. Currently, we have 2 Cisco AiroNet 1130 WAP's in the office that go directly into the 2 POE ports on our Cisco ASA 5500. These WAP's have 1 SSID and are using WEP for security. After demonstrating the flaws of WEP to my boss, he has agreed that we should use something more secure and I've suggested WPA. We want visitors to our office to be able to hop on our wireless but on a separate guest SSID with WEP.
I'd like the internal SSID to route to the ASA and take the default route to the internet (it will be our new fiber connection once it's installed in a couple weeks). The default route is whichever connection is working since our ASA 5500 will fail over when it detects an outage.
I'd like the guest SSID to route to the ASA and then go over our existing cable connection. This connection will be our backup once the fiber connection is installed. Since we won't be using it very often, but will be paying for it, I advised that we send all guest wireless traffic over this connection since 50/5 is plenty for guests.
The current SSID (which will be the internal SSID) has no VLAN. We do currently have a few VLANS on our network, one for voice (.42) and one for data (.100) and the default (.0). What device to I create the VLAN on (Cisco 5500?) and how to I setup the WAP? I need very basic instructions to start and I'm also trying to do this without causing downtime if possible.
I've attached a diagram of what it should look like. Red indicates our internal network and Blue indicates the guest network. I can send screenshots as well.
View 2 Replies
View Related
Aug 7, 2012
At work we have some older 1231 AG model access-points and a WLC with version 7.0. I was trying to convert them to lightweight and they will not join the controller without importing a .CSV file into the WLC. I cannot figure out to import that file, I cannot find any documentation on how to add the certificate with version 7.0.
View 2 Replies
View Related
Jul 11, 2012
I have four 1200 series AP. Part number of these AP's is AIR-AP1231G-A-K9. I am thinking to buy a new 2504 WLC with 5 AP licenses. Just wondering whether my AP's are compatible with WLC or not. These AP's are in close proxomity and start contending with each other if I configure the stand alone.
View 3 Replies
View Related
Oct 1, 2012
Converted a Cisco 1231 with the Update Tool to lightweight (used c1200-rcvk9w8-tar.124-21a.JA2.tar). It worked, but now the AP issn't joining the wlc: [code]
View 8 Replies
View Related
Oct 29, 2011
We have found that only Cisco 1231 WAP are exhibiting this behaviour. Their Primary WLAN controller is Cisco1 WLC but they fail to register to Primary WLC and fall back to Cisco2 WLC. After about 200 sec , they attempt to connect to Primary WLC once again and fail. The whole cycle is repeated every 250 seconds.
View 3 Replies
View Related
Oct 31, 2011
I have a problem where clients cannot roam between Cisco 1231g-e-k9 and recently installed cisco 1242g-e-k9 access points.. On looking at the CDP option on the 1231 and 1242 access points they are all aware of each other. However if I use the Network View option I see a different picture. All the 1231 access points can see each other but not see the 1242's. Network View on the1242 shows all the 1231's but none of the 1242's. The 1231 are running ver. 12.3(8)JEB and the 1242's are running ver. 12.4(21a)JA1.
View 2 Replies
View Related
Apr 28, 2013
WLC shows the next error.
AP with MAC 00:1e:13:10:40:59 (AIR-AP1231G-E-K9 ) is unknown.
I updated the AP to lightweighd firmware using upgrade tool. But upgrade tool generate the csv files empty so I had no idea about Hash key, so I resetted the APs to default values.
WLC still doesn't register them.
How Can I register the APs? The version of the WLC is 7.3.101.0
View 4 Replies
View Related
Dec 4, 2011
Customer is interested in deploying the 3600 AP's but will not be able to replace all his 1231's, any chance there is a release between 7.0.220.0 and 7.1.91.0 that will support both AP's?
View 6 Replies
View Related
Jun 28, 2012
I'm trying to setup 2 VLAN's 1 for Native Traffic on my Corp network and another VLAN for Guest Wireless traffic. I have attached the Config from my Cisco AP1231 and my Cisco 3750. I have the AP plugged into port 24 on my switch. I seem to have the VLAN's working fine. I can get the AP1231 to broadcast both SSID's and the very first time i can connect everything seems to work fine. after i power down my switch and AP i cannot connect to either SSID. I get the message Not Connected.
View 2 Replies
View Related
Apr 22, 2012
I have my all my computers, printers setup with a wireless network with dsl modem connected to linksys wireless router. I just signed up with comcast with another wireless router. I do not want to reconfigure all the laptops and printers with the new comcast wireless SSID. Is there a way I can connect the linksys router with existing SSID with the comcast router and using the internet speed of comcast. (note. will disconnect service with dsl)
View 3 Replies
View Related
Jan 23, 2013
I have one controller 2504 and some 1200 series access points.I am using 3 SSID .I want to use two ssid in HREAP mode but HREAP mode is not showinh in access point because multicast is enabled on AP mode. see the below picture
I have disabled the multicast globally from CLI. config network multicast global disabled
disabling the multicast so that i can set the access point in HREAP mode.
View 3 Replies
View Related
Nov 15, 2011
I have a WAP4410n which has been configured with a single SSID since implementation several weeks ago with no issues. I am now trying to add a second SSID and not having any success. Originally the second SSID was not being assigned a MAC address and thus not being broadcasted. After upgrading firmware to 2.0.4.2 I now see a MAC address associated with second SSID and it is being seen by clients, but they still cannot connect. I reset the AP to default settings and reconfigured from scratch but still no luck. I have two of these APs, the other one is still at FW rev 2.0.1.0 and has same issue (it does have MAC address associated with second SSID so I didn't bother upgrading firmware yet).
I have tried a few different authetication options, including disabling authentication, to no avail. Question - I do not see an IP address associated with the second SSID - is that the problem and if so, how do I fix that?
View 1 Replies
View Related
May 21, 2012
I would like to connect the AP541N to the RV220W and use the same SSID assigned to both throughout the office, for seemless client movement. I would like to keep the AP541N connected via the internet cable, as it will be on a switch which is on the same segment. The access point has many different configuration methods available, but the router appears to only have WDS as an option to connect the two devices. I would rather not use the WDS feature on the AP, as I want to utilize as much bandwidth available as possible, and I assume using that method I would need to remove the ethernet cable from the switch.
Is it as simple as configuring both devices with identical VLAN settings? I am preconfiguring the devices before installing them, as to minimize downtime, so would like to make sure the configuration is correct.
View 1 Replies
View Related
Jul 13, 2012
Where I live there is no DLS or cable to probide me with Interent access so I use my Verizon 3G/4G smart phone (Android) as a hotspot. Right now I am using an old Vista PC and ICS (Internet Connection Sharing) to provide Interent connectivity to my home network and Cisco lab. This works fine but I must have my smart phone near the PC for it to work. When I go to other rooms, I end up missing calls and texts since I have t oleave the phone if it is providing Inerent access at that time. If I can get the Airnet's to connect to the hot spot AND provide Internet access, that will provide me additional mobility. This would also be good for small businesses as a backup Internet Connection.
Is there any way that I could elimanate the Vista PC and have my Aironet 1231G Wireless router(s) automatically connect to my phone's 3G hotspot to provide Internet access to my lan?
I have 2 Airnoet 1231G's running the c1200-k9w7-mx.123-7.ja IOS and a C3550XL layer 3 switch.
View 5 Replies
View Related
Dec 5, 2012
Can I connect various Aironet 1242 to Wireless controller 2500?
View 4 Replies
View Related
Sep 9, 2012
I am tryign to set up an Aironet 1142, I have created a reserrvation in DHCP using the MAC address, and the reservation shows as active, but I cannot connect to the device with my browser.
View 1 Replies
View Related
