At work we have some older 1231 AG model access-points and a WLC with version 7.0. I was trying to convert them to lightweight and they will not join the controller without importing a .CSV file into the WLC. I cannot figure out to import that file, I cannot find any documentation on how to add the certificate with version 7.0.
View 2 RepliesI have four 1200 series AP. Part number of these AP's is AIR-AP1231G-A-K9. I am thinking to buy a new 2504 WLC with 5 AP licenses. Just wondering whether my AP's are compatible with WLC or not. These AP's are in close proxomity and start contending with each other if I configure the stand alone.
View 3 Replies View RelatedConverted a Cisco 1231 with the Update Tool to lightweight (used c1200-rcvk9w8-tar.124-21a.JA2.tar). It worked, but now the AP issn't joining the wlc: [code]
View 8 Replies View RelatedWe have found that only Cisco 1231 WAP are exhibiting this behaviour. Their Primary WLAN controller is Cisco1 WLC but they fail to register to Primary WLC and fall back to Cisco2 WLC. After about 200 sec , they attempt to connect to Primary WLC once again and fail. The whole cycle is repeated every 250 seconds.
View 3 Replies View RelatedI have some old 1231 APs in the school in which I work.I would like to create a local network (no LAN, no internet, just a point to point wifi connection) managed by the access point (in DHCP).That's because we have an apple TV connected to a projector and some ipads. My idea was to put the devices locally in the same closed network for share via AIR Mirror the ipads on the apple TV.
View 3 Replies View RelatedI'm having little success migrating our older Aironet1231 to our new WLC 5508. The 1231 is currently registered as a LAP to a 4400 WLC and I'm in the process of moving away from this controller to the new one. I've pasted the output of the error messages I'm getting below. At this point, I'm stuck and not sure how to get around the "Failed to parse CAPWAP packet" error.
I'm getting these messages when I have:
debug pm pki enable
debug capwap errors enable
I initially got this error, but got passed it when I allowed SSC in the 5508 (Security -> AP Policies)
sshpmGetIssuerHandles: SSC is not allowed by config; bailing...
Now I'm getting these:
*sshpmLscTask: Jul 09 11:13:11.516: sshpmLscTask: LSC Task received a message 4
I have a problem where clients cannot roam between Cisco 1231g-e-k9 and recently installed cisco 1242g-e-k9 access points.. On looking at the CDP option on the 1231 and 1242 access points they are all aware of each other. However if I use the Network View option I see a different picture. All the 1231 access points can see each other but not see the 1242's. Network View on the1242 shows all the 1231's but none of the 1242's. The 1231 are running ver. 12.3(8)JEB and the 1242's are running ver. 12.4(21a)JA1.
View 2 Replies View RelatedI have configure my AP with to SSID (11 & 12), but I cannot connect to 12. It authenticates, and while trying to acquire IP address from 12, it fails and connects me to 11 (if I have already saved the SSID connection).
The following is my AP status:Product/Model Number:AIR-AP1231G-A-K9 System Software Filename:c1200-k9w7-tar.123-8.JEE System Software Version:12.3(8)JEE Bootloader Version:12.3(2)JA4
The SSID 12 already have 4 clients connected, And I am tring to connect a 5th one (smart phone), but cannot connect to 12, instead coneected to 11. Also tried with a laptop, but cant get the IP address, and give Limited Connectivity error.
WLC shows the next error.
AP with MAC 00:1e:13:10:40:59 (AIR-AP1231G-E-K9 ) is unknown.
I updated the AP to lightweighd firmware using upgrade tool. But upgrade tool generate the csv files empty so I had no idea about Hash key, so I resetted the APs to default values.
WLC still doesn't register them.
How Can I register the APs? The version of the WLC is 7.3.101.0
I have a (old) 1231 that I would like to reuse, but no one remembers the password. how to recover a password from this model AP or how to reset the device to factory default?
View 1 Replies View RelatedCustomer is interested in deploying the 3600 AP's but will not be able to replace all his 1231's, any chance there is a release between 7.0.220.0 and 7.1.91.0 that will support both AP's?
View 6 Replies View RelatedI have one controller 2504 and some 1200 series access points.I am using 3 SSID .I want to use two ssid in HREAP mode but HREAP mode is not showinh in access point because multicast is enabled on AP mode. see the below picture
I have disabled the multicast globally from CLI. config network multicast global disabled
disabling the multicast so that i can set the access point in HREAP mode.
I cannot TFTP this tar file to both 1230 and 1231 APs. Both are lightweight APs that I've wiped to the rommon mode (ap>) and I issue the command:
tar -xtract c1200/k9w7-mx.123-8.JA 10.0.0.2
And I get a error saying: "permission denied"
Notes:
The AP has defaulted to the 10.0.0.1 IP.
My laptop is set to 10.0.0.2 255.255.255.0 IP
My TFTP-Server is on and the root folder with the .tar file is in there.
ether_init, flash_init, tftp_init (these commands have been executed)
My firewall is disabled.
We have a 1231 AP and a Freeradius Server.Now we are using MAc authentication.The thing is that the AP sends two parameters to the RADIUS:
User-Name = "000ff855df2e"
User-Password = "000ff855df2e"
both are the MAC of the wireless client.I want that the AP send:
User-Name = "00-0f-f8-55-df-2e"
User-Password = "mykey"
Note that the MAC is dash separated and the password is forced to the key that I want.
I can't seem to get the SSID RadiusTest to work properly.
Windows PC's show "Windows was unable to find a certificate to log you into the network". Macs don't authenticate either. Radius server isn't seeing any requests at all. Radius server is working because we are authenticating other things to it.
On my test 1231, IOS is 12.3(8) JEB1.
version 12.3
no service pad
service timestamps debug datetime msec
[Code].....
I have two 1231G Aironet's that work correctly when I connect them to my Catalyst 3548XL and my 3550-48-XL switches. When I connect them to the 3550-24-PWR switch I do see them when I issue sh cdp nei det. It shows me the IP of the wireless router. But when I ping the Aironet, I do not get any replies. If I plug the Aironet into my 3548XL and ping the IP, I get 5 replies. Here is the port config on both switches:
switchporrt trunk encapsulation dot1q
switchport native vlan 100
switchport allowed vlan 1,69,100,125,200,1002-1005
switchport mode trunk
spanning-tree portfast
Here is the sh cdp nei det results:
Device ID: North_AP.mtd.home
Entry address(es):
IP address: 192.168.100.104
Platform: cisco AIR-AP1231G-A-K9 , Capabilities: Trans-Bridge
Interface: FastEthernet0/3, Port ID (outgoing port): FastEthernet0
[code]....
I have tried two versions of the IOS on the 3550PWR switch. Right now its: c3550-ipservices-mz.122-44.SE6
After upgrading from a 1231 autonomous to an 1142 autonomous AP some machines can no longer authenticate. AP logs show authentication failure and access reject coming from the Radius server. Radius server shows authentication failures but no specific reason. Using the same account on another machine works fine. Machine settings have been verified and if we go back to the 1231 all users authenticate fine. Below are the configs:
OLD AP:
!
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec localtime show-timezone
service password-encryption
[code]...
I have an Acer 7750G, running Windows 7,connected to our home network using a Dynex router. At the moment this is the only laptop in the house that is having problems with connectivity. Starting yesterday, it only connects intermittently. When I run diagnostics, it says the following problems have been fixed but it either solves the problem for a few minutes only or not at all: "Problem with wireless adapter or access point" or "Default gateway is not available".
IPV6 connectivity also shows 'no internet access' and sometimes IPV4 reports no internet. I've unplugged and rebooted the modem and router a few times but that hasn't solved the problem.
Edit: I ran troubleshoot again, and it says the following issue is not fixed: "Wireless Network Connection 2 does not have a valid IP configuration".
I just bought a "DLink Xtreme N Gigabit Router DIR-655" I configured it correctly. It works well for the wireless connection but my Lan connection (wired connection) does not work. The Lan computer connects to the router but cannot access the internet. All of my machines work OK with a Netgear G router, including the Lan computer.
View 9 Replies View RelatedAfter connecting to the internet on my laptop, the internet connection will work great for 10 minutes or less than it slows down drastically or essentially not working at all. If I disconnect and reconnect it will work again but just for a short amount of time. The wireless connection works great on iPod, IPhone, and tablet. Downloaded Kaspersky Antivirus which said it fixed some viruses but internet got worse after that. Tried restoring the computer to factory settings and the internet stays connected for what seem a few minutes longer.
View 3 Replies View RelatedI have a Cisco 3725 running IOS 12.3. I have three WAN connections (2 x 100Mb and 1 x 2Mb serial) and I need to replace the 2Mb serial connection with a further 100Mb connection. However, I have not got any spare 100Mb sockets.My plan is to use a switch that supports VLANs, connect the three WAN connections to the switch, each in their own VLAN, then connect the switch to one port on the router, configuring the switch port as a trunk (so that it passes all three VLANs across the link) and configuring the router so that for that single Ethernet interface, it has three subinterfaces each configured for a VLAN that matches the VLAN used for the corresponding WAN connection.
I am a bit rusty on my IOS so I wanted to run this all past the community for feedback. [code] Any thoughts on whether or not that will work? Are there any commands from the original interface configurations that I CANNOT use when moving them to a subinterface? I'm thinking that the speed & duplex commands need to be removed?
We're getting "Connaction Timeout / Connection Failure" error messages several time per day. Here is our setup:
Verizon FiOS Internet (ONT Box) --> Cisco ASA 5505 --> EdgeMarc 4500 Router --> Cisco 300-24G Switch --> Dell PE1950 Servers
From past few months, we keep getting Connection Timeout and Connection Failure error messages in our vendor application which connects to SQL Server 2005. Also Terminal Server 2003 keep disconnecting for every few hours.After several days of troubleshooting, we come to know that this Cisco ASA 5500 is not working properly. When I access the ASDM, it shows several warning messages.I know there is a setting option to configure TimeOut, but is there anyway to test and track the ASA 5500 regarding this Timeout issues?
I am running 5508 controller with version 7.0 and 1142N access points.. I am facing a problem on user connectivity.
Wireless Users are getting frequent connection and disconnection. These users are not getting connected to the access point nearby although this access point is up and running. I have tried reducing the power level, configured the AP after resetting it.
I have a problem with my computer connections.When I plug in a network cable to access LAN, a wireless Internet connection gets disconnected.When I unplug the cable internet connection through wireless comes up.Some computers can support both connections cable for LAN and wireless for Internet.Other computers do not support both connections.
View 7 Replies View RelatedI am trying to confgure a VPN connection on a Cisco ASA 5505, and I am supposed to translate the inside network from 10.200 76.0 to host 10.1.4.204, and then from that scheme establish a VPN with the host 66.179.80.108 on network 192.168.50.0/24. I was told that this Cisco ASA appliace would be able to translate the network address as a mask in order to make the necessary connection with the other site connection.
View 6 Replies View Relatedso I would like to know if I have a cisco 800 series lets say with interface fa0/0 being my public interface.can I have on this interface an easyvpn connection to a hub and a crypto map xyz connection to another hub?all the tests I've done using gns3 indicate no. when I have both on the same interface only eazyvpn works. when I remove the eazyvpn from the interface then site to site works.I know with a crypto map I can have different tunnels but my question is a crypto map and an eazyvpn on the same outside interface can it work.if yes, do you have a configuration example of the 2 hubs and the spoke?
View 1 Replies View RelatedI have a Packard Bell Laptop using Windows XP OS and doesn't have Wireless Connection. So long ago i bought a Linksys by Cisco Wireless-G Notebook Adapter WPC54G v.1.2 but didn't have time to set it up or use it for travelling conditions. A couple years later when i came back to check on the laptop, i noticed that i lost the setup CD. So i went on the Linksys website and looked for the driver the download. On the back of the Adapter(card) it says it is version 1.2. But this version is unavailable on the Linksys Website. I could only find v.1, 2,3,3.1 and 7. v.1 gives a driver of v3.1 etc... AND NOT VICE-VERSA.So first when i inserted the card into the slot , the PC didnt detect it. It only detected it rarely if i insert another driver (eg: USB..). And so a window would pop up to install but i didnt know what to do there. When i downloaded the v.1 driver from the website and installed it, it seemed not the detect the card either, it would just say searching for wireless, but that's it. It would keep searching for hours even when im next to the router.finally, only the Power led light on the card is lit up but not the "Link" led.
View 1 Replies View RelatedI just connected a WRT190N v2 Wireless Router to my XPS 400. When my wife tried to connect our other desktop to the wireless network, everything seemed fine. I noticed that, when she wasn't actively browsing or using the network, her computer would lose connectivity, but regain it when a browser was opened. When I tried to use the XPS, I found that it had no connection. I regained connectivity after using the Windows Network Diagnostic tool, but neither computer seems to keep connectivity when left alone, at least for very long.
View 1 Replies View RelatedI get frequest Airport Express wireless connection drop and reconnect with my replacement e4200v2 running the latest firmware. I have it connected the 5Ghz band and set to channel 161.
View 9 Replies View RelatedFor the last 4 years I’ve been using the Linksys Router, model WRT150N V. 1.1 and never had any problems—until now.Yesterday I noticed that my wireless devices (i.e., two computers, tablet and Internet radio) either don’t work at all (the Internet radio) or the pages load extremely slowly—for example, the tablet has become, for all intents and purposes, unusable. Since my ‘main’ computer is connected directly to my cable internet, I know that there is nothing wrong with the Internet connection itself, only with wireless connection.I disconnected the Linksys Router for 2 minutes and reconnected it, but to no avail. I know that I have not made any changes to any software/hardware that might affect the speed.Since I also happen to have access to another wireless Internet connection (a different provider), I connected to that network and all my wireless devices were working perfectly. Therefore, I think the problem must be with the router. I am using Windows XP (on the main computer, where the router and Internet cable are attached).
View 5 Replies View RelatedI have a Linksys WUSB54G version 4 adapter.My computer is running Windows XP, Service Pack 3, which is automatically updated at all times. I've been using the adapter for a year with no problems.
Suddenly, it's started loosing the connection to the Linksys router and locking up my computer so only a hard re-boot power-down will work.When it comes back up, some or all of my cookies are lost.
I've run several different security packages but no virus or other issues have been found.I've uninstalled the adapter and reinstalled it.Last time, following something I read on this site, I installed it without the Linksys software, just the drivers.
I have a Netgear CGD24G Wireless Gateway and a Gateway MA8 laptop with after-market Windows 7 (Vista got a virus, went ahead and upgraded.)Now, when I download 100 MB files on my Xbox 360 (Which is wired to the modem) it will be downloaded in a couple minutes, or less. The other computers in my house (There are plenty, and even more that come and go.) get a blazing internet connection, and most of them are wireless.Now this computer, which had an extremely quick connection as well all of a sudden dropped off, while the rest of the computers remain fast.I've gone to Speedtest.net before and after this occurred and my speed before was around 12 mb/s, and one time around 4 AM was even upward of 25 mb/s, all of these tests were performed multiple times on different server locations. I JUST did the speedtest, and it came back with .4 mb/s, and the UL speed was 2.0. I honestly can't remember what I averaged with it prior to the problem, but it was definitely higher as well
View 5 Replies View RelatedI am currently having problem Enabling my wireless network connection by using AE1000
My system info are as follow
p4p800-e deluxe (mainboard) intel pentium 4 1gb Ram Window 7 32 Bit Marvell Yukon 88E8001/8003/8010 PCI Gigabit Ethernet Controller Intel 82801EB USB2 Enhanced Host controller - 24DD (USB 2.0) ZoneAlarm(firewall)
After intalling AE1000 Driver, I was unable to connect to internet and Wireless network connection appeared disabled in my Network Connections folder. However it is shown to be Enabled in my Device manager screen. no matter what I do, I am unable to enable the connection and connect to internet (when tryiing to enable the connection, a enabling screen pops up, and times out. device still shown to be disabled/grey).
I made the following attempt trying to get this fixed.
uninstalling the deivce and reinstalling it. (doesnt work) uninstalling the device, restart and have the windows update install the device (the deviced was installed. however I am still not able to enable it) Disable & Enable TCP/IPv4 & TCP/IPv6 (doesnt work) uninstalling local Area connection and use wireless to connect (doesnt work) download driver from websit, and install it manually. (does not work) connecting thou CD. I was given a msg telling me to disable my 'other' wireless manager and use the windows wireless manager to connect (i have no idea i had 'Other' Wireless manager >.>) testing whither or not the same adapter works on another PC (it works...) Testing wither or not my router is not working... (well.. im typing right now... so it works...)