Cisco Wireless :: 1242G-E-K9 Not Seeing Other 1242s Or 1231 On Network?
Oct 31, 2011
I have a problem where clients cannot roam between Cisco 1231g-e-k9 and recently installed cisco 1242g-e-k9 access points.. On looking at the CDP option on the 1231 and 1242 access points they are all aware of each other. However if I use the Network View option I see a different picture. All the 1231 access points can see each other but not see the 1242's. Network View on the1242 shows all the 1231's but none of the 1242's. The 1231 are running ver. 12.3(8)JEB and the 1242's are running ver. 12.4(21a)JA1.
View 2 Replies
ADVERTISEMENT
Jul 26, 2012
1. Does the Aironet 1242G have an internal antenna?
2. When connecting an AIR-ANT1728 omnidirectional to the primary connector on the ap, does this have to be enable or is it enable by default?
3. My laptops can connect and travel between access point just fine, but smartphones cannot even see the network.
View 4 Replies
View Related
Aug 7, 2012
Is there a way to set up these ap's to bridge. Ie two buildings 100 yards apart Both buildings have wired clients into a Cisco poe switch. Want to plug the ap's into each switch and have them bridge the data and even better if they could trunk vlans. No wireless clients at all. Strictly a point to point bridge. Also will they need to be lwaps or standalone APs. If they are lwaps can I flash to standalone ?
View 3 Replies
View Related
Feb 26, 2013
This is just a tip that we used on our controllers that I wanted to pass along. We were having issues with unwanted access points associating to our controllers. We had a stack of older 1242s that came up missing and hit our network. On way we came up with to prevent this was to number all of our wlans above I'd # 16 on the controller. By default the default ap group allows all wlans from 1 to 16. By starting with 17 we are not allowing any SSIDs in the default group. All if our production access points are in their own ap groups. Any access point that hits our controllers that has not been configured with the correct ap group name will be in the default ap group and will not be servicing any SSIDs.I know there are other ways to set this up but this was a tricky way for us to set it up and see who calls about there wireless not working.
View 3 Replies
View Related
Feb 8, 2011
I've got a network of several AIR-LAP-1242G LWAPP access points controlled by a 2112 WLC. I assign static IP addresses to each LWAPP, but every few weeks, a couple of them (at random) revert back to grabbing a DHCP-assigned dynamic address for themselves, despite the fact that they're supposedly solidy configured to have static IPs. What's going on here? Is this a bug in their firmware or the WLC's firmware? If I reboot the APs, then they come up with their static IPs, but after running some random number of days/weeks, will spontaneously change their own management IP addresses and grab a DHCP address for themselves.
The 1242G APs version numbers reported by the WLC's web GUI are:
"Software version" 5.2.193.0
"Boot version" 12.4.13.0
"IOS version" 12.4(18a)JA2
"Mini IOS version" 3.0.51.0
The 2112 WLC is running software version 5.2.193.0
View 2 Replies
View Related
Aug 7, 2012
At work we have some older 1231 AG model access-points and a WLC with version 7.0. I was trying to convert them to lightweight and they will not join the controller without importing a .CSV file into the WLC. I cannot figure out to import that file, I cannot find any documentation on how to add the certificate with version 7.0.
View 2 Replies
View Related
Jul 11, 2012
I have four 1200 series AP. Part number of these AP's is AIR-AP1231G-A-K9. I am thinking to buy a new 2504 WLC with 5 AP licenses. Just wondering whether my AP's are compatible with WLC or not. These AP's are in close proxomity and start contending with each other if I configure the stand alone.
View 3 Replies
View Related
Oct 1, 2012
Converted a Cisco 1231 with the Update Tool to lightweight (used c1200-rcvk9w8-tar.124-21a.JA2.tar). It worked, but now the AP issn't joining the wlc: [code]
View 8 Replies
View Related
Oct 29, 2011
We have found that only Cisco 1231 WAP are exhibiting this behaviour. Their Primary WLAN controller is Cisco1 WLC but they fail to register to Primary WLC and fall back to Cisco2 WLC. After about 200 sec , they attempt to connect to Primary WLC once again and fail. The whole cycle is repeated every 250 seconds.
View 3 Replies
View Related
Sep 12, 2012
I have some old 1231 APs in the school in which I work.I would like to create a local network (no LAN, no internet, just a point to point wifi connection) managed by the access point (in DHCP).That's because we have an apple TV connected to a projector and some ipads. My idea was to put the devices locally in the same closed network for share via AIR Mirror the ipads on the apple TV.
View 3 Replies
View Related
Jul 8, 2012
I'm having little success migrating our older Aironet1231 to our new WLC 5508. The 1231 is currently registered as a LAP to a 4400 WLC and I'm in the process of moving away from this controller to the new one. I've pasted the output of the error messages I'm getting below. At this point, I'm stuck and not sure how to get around the "Failed to parse CAPWAP packet" error.
I'm getting these messages when I have:
debug pm pki enable
debug capwap errors enable
I initially got this error, but got passed it when I allowed SSC in the 5508 (Security -> AP Policies)
sshpmGetIssuerHandles: SSC is not allowed by config; bailing...
Now I'm getting these:
*sshpmLscTask: Jul 09 11:13:11.516: sshpmLscTask: LSC Task received a message 4
View 3 Replies
View Related
Apr 22, 2013
I have configure my AP with to SSID (11 & 12), but I cannot connect to 12. It authenticates, and while trying to acquire IP address from 12, it fails and connects me to 11 (if I have already saved the SSID connection).
The following is my AP status:Product/Model Number:AIR-AP1231G-A-K9 System Software Filename:c1200-k9w7-tar.123-8.JEE System Software Version:12.3(8)JEE Bootloader Version:12.3(2)JA4
The SSID 12 already have 4 clients connected, And I am tring to connect a 5th one (smart phone), but cannot connect to 12, instead coneected to 11. Also tried with a laptop, but cant get the IP address, and give Limited Connectivity error.
View 3 Replies
View Related
Apr 28, 2013
WLC shows the next error.
AP with MAC 00:1e:13:10:40:59 (AIR-AP1231G-E-K9 ) is unknown.
I updated the AP to lightweighd firmware using upgrade tool. But upgrade tool generate the csv files empty so I had no idea about Hash key, so I resetted the APs to default values.
WLC still doesn't register them.
How Can I register the APs? The version of the WLC is 7.3.101.0
View 4 Replies
View Related
Sep 17, 2012
I have a (old) 1231 that I would like to reuse, but no one remembers the password. how to recover a password from this model AP or how to reset the device to factory default?
View 1 Replies
View Related
Dec 4, 2011
Customer is interested in deploying the 3600 AP's but will not be able to replace all his 1231's, any chance there is a release between 7.0.220.0 and 7.1.91.0 that will support both AP's?
View 6 Replies
View Related
Jan 23, 2013
I have one controller 2504 and some 1200 series access points.I am using 3 SSID .I want to use two ssid in HREAP mode but HREAP mode is not showinh in access point because multicast is enabled on AP mode. see the below picture
I have disabled the multicast globally from CLI. config network multicast global disabled
disabling the multicast so that i can set the access point in HREAP mode.
View 3 Replies
View Related
Jan 22, 2013
I cannot TFTP this tar file to both 1230 and 1231 APs. Both are lightweight APs that I've wiped to the rommon mode (ap>) and I issue the command:
tar -xtract c1200/k9w7-mx.123-8.JA 10.0.0.2
And I get a error saying: "permission denied"
Notes:
The AP has defaulted to the 10.0.0.1 IP.
My laptop is set to 10.0.0.2 255.255.255.0 IP
My TFTP-Server is on and the root folder with the .tar file is in there.
ether_init, flash_init, tftp_init (these commands have been executed)
My firewall is disabled.
View 18 Replies
View Related
Jun 21, 2006
We have a 1231 AP and a Freeradius Server.Now we are using MAc authentication.The thing is that the AP sends two parameters to the RADIUS:
User-Name = "000ff855df2e"
User-Password = "000ff855df2e"
both are the MAC of the wireless client.I want that the AP send:
User-Name = "00-0f-f8-55-df-2e"
User-Password = "mykey"
Note that the MAC is dash separated and the password is forced to the key that I want.
View 2 Replies
View Related
Jan 12, 2011
I can't seem to get the SSID RadiusTest to work properly.
Windows PC's show "Windows was unable to find a certificate to log you into the network". Macs don't authenticate either. Radius server isn't seeing any requests at all. Radius server is working because we are authenticating other things to it.
On my test 1231, IOS is 12.3(8) JEB1.
version 12.3
no service pad
service timestamps debug datetime msec
[Code].....
View 2 Replies
View Related
Oct 30, 2012
I have two 1231G Aironet's that work correctly when I connect them to my Catalyst 3548XL and my 3550-48-XL switches. When I connect them to the 3550-24-PWR switch I do see them when I issue sh cdp nei det. It shows me the IP of the wireless router. But when I ping the Aironet, I do not get any replies. If I plug the Aironet into my 3548XL and ping the IP, I get 5 replies. Here is the port config on both switches:
switchporrt trunk encapsulation dot1q
switchport native vlan 100
switchport allowed vlan 1,69,100,125,200,1002-1005
switchport mode trunk
spanning-tree portfast
Here is the sh cdp nei det results:
Device ID: North_AP.mtd.home
Entry address(es):
IP address: 192.168.100.104
Platform: cisco AIR-AP1231G-A-K9 , Capabilities: Trans-Bridge
Interface: FastEthernet0/3, Port ID (outgoing port): FastEthernet0
[code]....
I have tried two versions of the IOS on the 3550PWR switch. Right now its: c3550-ipservices-mz.122-44.SE6
View 5 Replies
View Related
Dec 9, 2012
After upgrading from a 1231 autonomous to an 1142 autonomous AP some machines can no longer authenticate. AP logs show authentication failure and access reject coming from the Radius server. Radius server shows authentication failures but no specific reason. Using the same account on another machine works fine. Machine settings have been verified and if we go back to the 1231 all users authenticate fine. Below are the configs:
OLD AP:
!
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec localtime show-timezone
service password-encryption
[code]...
View 3 Replies
View Related
Oct 29, 2012
Having an issue with a Cisco Linksys E1500 on a home network. The device has a feature to provide a guest wireless network but the guest network can't get to the internet. A wired connection is fine, as is the normal wireless network but not the guest. The cheesy thing is, that it doesn't list an option for what type of wireless security protocol you want on the guest network. I'm assuming that it uses the same security protocol that the normal wireless network uses, but who knowsEspecially weird is that it asks you what password you want on the guest network but then the guest network show to be insecure when you try to connectthought maybe it was something funky with some of my configurations so I went ahead and factory defaulted it and just set it up with an insecure network for both the normal and guest networks. This didn't solve it. The guest network still couldn't get to the internet. In fact, the guest network can't even ping the router.
View 1 Replies
View Related
Apr 4, 2012
I have 4 computers (3 laptops, 1 desktop) in a shared office. We get internet access using their wireless network. All works fine. However, I need to share a printer amongst all of the computers. The printer is LAN enabled and I would normally just put all the PCs on a hub, together with the printer and share it that way. BUT my question is can we access the internet using the wireless network and the printer using a separate wired network at the same time?
View 7 Replies
View Related
Aug 21, 2012
This past weekend I went out of town and took my Windows 7 laptop with me -- since I returned home, it has been unable to connect to my wireless network. Other devices in my home connect to the network just fine, and the problem laptop has always been fine until now. My network card is an Atheros AR9285, and I'm attempting to connect to a Medialink router with WPA password protection and AES encryption.My wireless network icon in the task bar has a yellow sign with an exclamation point in it. It says "No Internet access."
View 1 Replies
View Related
Mar 3, 2012
I have a home network running all Mac computers (though can run Windows VM if necessary) and a pair of USB printers. The wireless router and cable modem are in one room, but the printers are in another. I'd like to find the most practical way to add the printers to the local wireless network without sharing them from a computer. I've tried that for a while, but don't want to leave a laptop connected 24/7 just to enable wireless printing (rather defeats the purpose of a portable computer). I don't have any wired network lines in the home, and am not excited by the idea of running any cables.
View 5 Replies
View Related
Jul 5, 2011
A few days ago the internet on my desktop was working fine. now it has the 'limited or no connectivity' sign on it and i have done a few things to try and fix this. I started by trying a simple repair. it comes up with 'the following action can not be completed: Renewing your IP address' This lead me to try and restart my PC and router with no luck.
I then decided to look a bit further into it and went ito CMD and flushed the DNS. i then did 'ipconfig /release' which generated the response 'IP address for adapter wireless connection 9 has allready been released'. I then did 'ipconfig /renew' to which it generated an interestin response:
'An error occurred while renewing interface wireless network connection 9 : The RPC server is unavailable'
I have made sure my DNS client is on automatic, alont with my RPC (this was uneditable). Its not a router problem as i have had multiple devices connected before and my laptop is working just fine connecting wirelessly.
View 14 Replies
View Related
Oct 10, 2011
I have been involved in the Networking of a museum with a set of "Show" computers which display video, and for this reason cannot have anti virus installed becuase of the performace hit, and also the risk of pop-ups on the videos. They do however need to be connected to the internet as some are interactive and allow people to send simple emails, and they all need to allow remote support when things go wrong.It seems the networking was not thought out very well initially, and there is a single wireless router which serves the staff and public on a secured wireless network, but also serves the "Show" machines via a wired connection from one of its ports, which then connects to a master switch which serves the show machines.Now the wired and wireless is on the same network, and everything shares the same IP subnet (192.168.1.xxx), and this is not a good situation in terms of the securuty of the show machines on the wired network. So I need to work out a way to totally separate the wireless network (which will be very prone to people opening viruses in their emails etc), from the wired network (which will be the show machines which wont be touched by anyone).
I want to achieve this in the simplest and easiest way, and have been reading about the possibility of setting up a second wired router behind the current wireless one, with a different subnet IP address, to which the "Show" machines could be connected. The WAN port on this second router would connect to a LAN port on the wireless router, and thus the show machines could get their internet, but separated from the dangerous wireless network.Does this sound like a sensible start? Will the fact that the wired router (and show machines) are on a completely different subnet to the wireless router (and wireless devices), mean that the wired network will be protected? Or do I need to do more? And is this likely to work?
View 3 Replies
View Related
Feb 25, 2012
I have just re-installed Windows Vista on my Toshiba Laptop and it connects fine to my virgin media router using a LAN line but when I try connecting wirelessly, no networks are found. I've tried up-dating the driver files form the C: drive(Window) and also from the net but with no joy.. Network adapter is a Realtek RTL 8187B. I hate admitting defeat as Im sure the solution is probably something simple..
View 3 Replies
View Related
Jan 22, 2011
I can find and connect to the wireless network in our house, but it has the yellow triangle with an exclamation mark. My housemates are on the internet fine on their laptops and my xbox live is working, so it's clearly an issue with my laptop. My laptop's internet evidently works with an ethernet cable too, but I can't just go through an ethernet cable all the time since the router is in a housemate's bedroom.
View 14 Replies
View Related
Jan 30, 2012
My computer is a 32 bit, Win7 SP1 with Pentium Dual Core 2.6 Ghz and 2Gb of Ram on a wired network. My wife has a similar system using a wireless network. She can ping my IP Address, but I cannot ping hers. We both have full access to the Internet. We are using the same workgroup, and both computers have file and printer sharing enabled and IPv6 addresses and DNS server addresses selected automatically.The problem appears to be with my computer?
Here are my system stats:
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 7 Home Premium, Service Pack 1, 32 bit
Processor: Pentium(R) Dual-Core CPU E5300 @ 2.60GHz, x64 Family 6 Model 23 Stepping 10
Processor Count: 2
RAM: 2013 Mb
Graphics Card: Intel(R) G41 Express Chipset, 782 Mb
Hard Drives: C: Total - 76308 MB, Free - 49226 MB; D: Total - 286167 MB, Free - 52893 MB; M: Total - 38154 MB, Free - 7 MB;
Motherboard: ASUSTeK Computer INC., P5G41-M LE
Antivirus: Microsoft Security Essentials, Updated and Enabled
View 5 Replies
View Related
Nov 1, 2011
I have a rather complex situation that requires (I think) a complex solution that I have not yet worked out! I have the following:
- ADSL internet connection
- TP-Link TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router
- Brand new Airport extreme (n)
- Four brand airport expresses (n)
- 24 port 3com switch.
My requirements are:
- A contained, protected, office network with wi-fi with access, and also access for wired clients via the 24 port switch.
- A "guest" network with only internet access which needs to be spread throughout a large, old building (thick stone walls!), but cabling is not possible.
My inital thought was to use the TP-Link as only a modem and run the network via the extreme. Plug the switch into the extreme which would also run the office wi-fi and then extend the guest network (nice extra option in the extreme!) thoughout the building with the expresses. Problem is that you cannot extend the guest network with either n or g. I cannot just reverse these two networks because I need wired access to the office network.The current system has the extreme running only the office network (wi-fi + wired) as a "double NAT" inside the "mother network" which is DHCPed by the TP-LINK with its wireless on (pretty good range). I set the expresses to extend the TP-Link's wireless by old fashioned WDS which I got working but it was incredibly slow just because that is what g WDS is like. I am not using the n capacity of the expresses.
I thought about using the TP-Link DHCP and wi-fi to run the office network and then I can use the extreme and the "extend my network" n option for better speeds around the building, but then the office network would be open to the guest network.
View 1 Replies
View Related
Nov 19, 2011
how to find the network security key,wireless network
View 1 Replies
View Related
Nov 26, 2011
we already have an existing network tru a switch hub and other two pc access internet through a wireless router and this wireless router is connected to the switch hub together with the other pc our problem is we cant share files and folders to the other two pc using wireless..How can we share files to other two pc.
View 3 Replies
View Related
