Cisco :: Changing AP 1230 And 1231 From Lightweight To Autonomous
Jan 22, 2013
I cannot TFTP this tar file to both 1230 and 1231 APs. Both are lightweight APs that I've wiped to the rommon mode (ap>) and I issue the command:
tar -xtract c1200/k9w7-mx.123-8.JA 10.0.0.2
And I get a error saying: "permission denied"
Notes:
The AP has defaulted to the 10.0.0.1 IP.
My laptop is set to 10.0.0.2 255.255.255.0 IP
My TFTP-Server is on and the root folder with the .tar file is in there.
ether_init, flash_init, tftp_init (these commands have been executed)
My firewall is disabled.
View 18 Replies
ADVERTISEMENT
Jan 12, 2011
I can't seem to get the SSID RadiusTest to work properly.
Windows PC's show "Windows was unable to find a certificate to log you into the network". Macs don't authenticate either. Radius server isn't seeing any requests at all. Radius server is working because we are authenticating other things to it.
On my test 1231, IOS is 12.3(8) JEB1.
version 12.3
no service pad
service timestamps debug datetime msec
[Code].....
View 2 Replies
View Related
Jan 17, 2011
I have some 1242s and I can't get a straight answer on whether they can do both autonomous and lightweight or just lightweight.
Model number: AIR-LAP1242AG-A-K9.
I'm assuming that the 'L' in the model numbers means it's just lightweight, but searching Cisco's site and the Internet in general it's just not clear.
I know it works as a lightweight AP, can I run it in autonomous mode?
View 3 Replies
View Related
Mar 4, 2012
I have a air-lap1042-n-e-k9, how to put this wi-fi mode autonomous ?
View 5 Replies
View Related
Apr 28, 2013
how to convert a 3502 access point from Autonomous to Lightweight ? 3502 has a new IOS released back in Dec 2012 to work as staandalone mode. I need to convert this back to Lightweight mode.
I have been searching on web but have had no luck so far with anything. Tried converting it to lightweight in the same way as putting it on Autonomous IOS but errored out.
View 4 Replies
View Related
Feb 28, 2013
how to convert a 1602i AP from lightweight mode to autonomous?
View 3 Replies
View Related
Feb 19, 2013
I have a problem converting 2602 from lightweight to autonomous. It will not boot to the autonomous IOS. The procedure below is waht I did.
ap: set IP_ADDR 10.0.0.1
ap: set NETMASK 255.255.255.0
ap: tftp_init
[Code].....
View 28 Replies
View Related
Jan 30, 2011
I keep getting the following error "Could not execute JDBC batch update" when trying to add AP to WCS ... other 1240 APs added without any problems.
View 4 Replies
View Related
Nov 10, 2012
Is it possible to convert an Autonomous AP 2602i to Lightweight just changing firmware as the first generation Aironet APs?
View 2 Replies
View Related
Apr 15, 2012
Apparently converting autonomous 1142N to lightweight is not supported by ether WCS 7.0 or the Upgrade tool. The option is to do it manually with CLI, but there is about 200+ AP's that need converting. We can't do them all at the same time. We have to do it building per building.
View 4 Replies
View Related
Apr 30, 2012
Doing the firmware upgrade on a 1041n AP from Autonomous to Lightweight. Downloaded from Cisco, checked MD5 and got a match so went and upgraded. Upgrade went find etc.. and rebooted. When I reboot I get the following error and then rubbish text
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0xc0000000
RQDC, RFDC : 0x80000037, 0x0000018a
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
[code]...
I rolled back to the autonomous OS and all ok and AP operates as normal. When on the lightweight IOS I can get a telnet response but cannot access as it states Password require but not set.
Followed this process to upgrade [URL] and followed this process to restore to Autonomous: [URL] why it's not working.
Update: Just tried another AP same result. Downloaded Lightweight again and same result
Here is the CLI upgrade process
examining image...
Loading c1140-rcvk9w8-tar.124-21a.JA2.tar .from 172.16.4.114 (via BVI1): !
extracting info (273 bytes)
Image info:
Version Suffix: rcvk9w8-
Image Name: c1140-rcvk9w8-mx
[code]....
View 1 Replies
View Related
May 21, 2012
is there any issue in buying air-ap1142n-ek9 802.11A/G/N FIXED AUTO AP INT ANT and later on converting it into lightweight under the control of air-ct2504-15k9 2504 WIRELESS CONTROLLER WITH 15 AP LICENSES ?Are there any requirements on the SW of the WLC and the IOS of the AP? The reason of the choice is budget.
View 1 Replies
View Related
Jul 12, 2012
This is one of our first site where we are implementing Cisco wireless, and we bought some external Autonomous AP1262, when we should have bought Lightweight LAP1262 . We can get those replaced, but I am looking into migrating them in order to get them to register with our 5508 controllers.
There do not seem to be a migration tool to download for 1262. Must it be done via the WCS ?So far I have not managed to add these autonomous AP to the controllers. How to know if a migration toll exists for those !
View 4 Replies
View Related
Aug 22, 2011
I have a Cisco WLC 5508 managing several 1252s in lightweight mode. There is a portable across campus that has a standalone network but no cabling to tie in to the corporate network. I have another 1252 that is in autonomous mode. Could I essentially configure that as a bridge with the same security and SSID in order to bridge the corporate WLAN? If not, what are my options?
View 4 Replies
View Related
Apr 20, 2012
Is it possible to convert a 1041 in Autonomous AP mode to Lightweight? Since on the cco page there is no upgrade tool under the 1040 series AP,and also i didnt find any document with the procedure.
View 1 Replies
View Related
Feb 4, 2013
What 113X AP model will work in Autonomous and LightWeight Mode? I want to buy some 113X AP's for my lab and want to make sure I don't get stuck with the ones that only run in one mode. I am looking at buying this one AIR-AP1131AG-N-K9 802.11a/b/g. Will this model work in both modes?
View 1 Replies
View Related
Jun 6, 2013
I have AP AIR-AP1231G-E-K9 with iOS c1200-k9w7-tar.123-7.JA2 and I want to convert it to Lightweight Mode with iOS image c1200-rcvk9w8 tar.124-21a.JA2. First of all, is it possible? Because I tried to convert from tftp server command (archive download-sw /overwrite /reload tftp://ipaddress/image.tar) and I cannot see in the controller. (controller and aps are in the same network)
View 11 Replies
View Related
Mar 4, 2012
We have recently converted 1 Cisco Lightweight AP 1041 to Autonomous mode for site-survey purposes. We now want to convert it back to lightweight mode.
View 1 Replies
View Related
May 7, 2012
my access point 1230 fail to join the controller. The image is C1200-k9w7-mx.123-8.JA2. I tried to reboot it but it does not join to controller. How do I initiate the discovery process again to make this AP to join? Should I convert it back to autonomous AP and then LWAPP process again? I can ping the AP from the controller and the AP is in the same VLAN with controller.
View 3 Replies
View Related
Mar 6, 2011
I just started a project to make a guest wireless network available at every site in my enterprise. Guest wireless networks are currently available at some sites. Two key goals of this project is to enable WPA/WPA2 encryption and to develop a web based registration/autentication solution. All of the sites have a mixture of 1230, 1240, and 1250 autonomous access points. What do I need to do/get in order to make this happen?
View 3 Replies
View Related
Aug 7, 2012
At work we have some older 1231 AG model access-points and a WLC with version 7.0. I was trying to convert them to lightweight and they will not join the controller without importing a .CSV file into the WLC. I cannot figure out to import that file, I cannot find any documentation on how to add the certificate with version 7.0.
View 2 Replies
View Related
Jul 11, 2012
I have four 1200 series AP. Part number of these AP's is AIR-AP1231G-A-K9. I am thinking to buy a new 2504 WLC with 5 AP licenses. Just wondering whether my AP's are compatible with WLC or not. These AP's are in close proxomity and start contending with each other if I configure the stand alone.
View 3 Replies
View Related
Oct 1, 2012
Converted a Cisco 1231 with the Update Tool to lightweight (used c1200-rcvk9w8-tar.124-21a.JA2.tar). It worked, but now the AP issn't joining the wlc: [code]
View 8 Replies
View Related
Oct 29, 2011
We have found that only Cisco 1231 WAP are exhibiting this behaviour. Their Primary WLAN controller is Cisco1 WLC but they fail to register to Primary WLC and fall back to Cisco2 WLC. After about 200 sec , they attempt to connect to Primary WLC once again and fail. The whole cycle is repeated every 250 seconds.
View 3 Replies
View Related
Sep 12, 2012
I have some old 1231 APs in the school in which I work.I would like to create a local network (no LAN, no internet, just a point to point wifi connection) managed by the access point (in DHCP).That's because we have an apple TV connected to a projector and some ipads. My idea was to put the devices locally in the same closed network for share via AIR Mirror the ipads on the apple TV.
View 3 Replies
View Related
Jul 8, 2012
I'm having little success migrating our older Aironet1231 to our new WLC 5508. The 1231 is currently registered as a LAP to a 4400 WLC and I'm in the process of moving away from this controller to the new one. I've pasted the output of the error messages I'm getting below. At this point, I'm stuck and not sure how to get around the "Failed to parse CAPWAP packet" error.
I'm getting these messages when I have:
debug pm pki enable
debug capwap errors enable
I initially got this error, but got passed it when I allowed SSC in the 5508 (Security -> AP Policies)
sshpmGetIssuerHandles: SSC is not allowed by config; bailing...
Now I'm getting these:
*sshpmLscTask: Jul 09 11:13:11.516: sshpmLscTask: LSC Task received a message 4
View 3 Replies
View Related
Oct 31, 2011
I have a problem where clients cannot roam between Cisco 1231g-e-k9 and recently installed cisco 1242g-e-k9 access points.. On looking at the CDP option on the 1231 and 1242 access points they are all aware of each other. However if I use the Network View option I see a different picture. All the 1231 access points can see each other but not see the 1242's. Network View on the1242 shows all the 1231's but none of the 1242's. The 1231 are running ver. 12.3(8)JEB and the 1242's are running ver. 12.4(21a)JA1.
View 2 Replies
View Related
Apr 22, 2013
I have configure my AP with to SSID (11 & 12), but I cannot connect to 12. It authenticates, and while trying to acquire IP address from 12, it fails and connects me to 11 (if I have already saved the SSID connection).
The following is my AP status:Product/Model Number:AIR-AP1231G-A-K9 System Software Filename:c1200-k9w7-tar.123-8.JEE System Software Version:12.3(8)JEE Bootloader Version:12.3(2)JA4
The SSID 12 already have 4 clients connected, And I am tring to connect a 5th one (smart phone), but cannot connect to 12, instead coneected to 11. Also tried with a laptop, but cant get the IP address, and give Limited Connectivity error.
View 3 Replies
View Related
Jun 21, 2006
We have a 1231 AP and a Freeradius Server.Now we are using MAc authentication.The thing is that the AP sends two parameters to the RADIUS:
User-Name = "000ff855df2e"
User-Password = "000ff855df2e"
both are the MAC of the wireless client.I want that the AP send:
User-Name = "00-0f-f8-55-df-2e"
User-Password = "mykey"
Note that the MAC is dash separated and the password is forced to the key that I want.
View 2 Replies
View Related
Apr 28, 2013
WLC shows the next error.
AP with MAC 00:1e:13:10:40:59 (AIR-AP1231G-E-K9 ) is unknown.
I updated the AP to lightweighd firmware using upgrade tool. But upgrade tool generate the csv files empty so I had no idea about Hash key, so I resetted the APs to default values.
WLC still doesn't register them.
How Can I register the APs? The version of the WLC is 7.3.101.0
View 4 Replies
View Related
Sep 17, 2012
I have a (old) 1231 that I would like to reuse, but no one remembers the password. how to recover a password from this model AP or how to reset the device to factory default?
View 1 Replies
View Related
Oct 30, 2012
I have two 1231G Aironet's that work correctly when I connect them to my Catalyst 3548XL and my 3550-48-XL switches. When I connect them to the 3550-24-PWR switch I do see them when I issue sh cdp nei det. It shows me the IP of the wireless router. But when I ping the Aironet, I do not get any replies. If I plug the Aironet into my 3548XL and ping the IP, I get 5 replies. Here is the port config on both switches:
switchporrt trunk encapsulation dot1q
switchport native vlan 100
switchport allowed vlan 1,69,100,125,200,1002-1005
switchport mode trunk
spanning-tree portfast
Here is the sh cdp nei det results:
Device ID: North_AP.mtd.home
Entry address(es):
IP address: 192.168.100.104
Platform: cisco AIR-AP1231G-A-K9 , Capabilities: Trans-Bridge
Interface: FastEthernet0/3, Port ID (outgoing port): FastEthernet0
[code]....
I have tried two versions of the IOS on the 3550PWR switch. Right now its: c3550-ipservices-mz.122-44.SE6
View 5 Replies
View Related
Dec 4, 2011
Customer is interested in deploying the 3600 AP's but will not be able to replace all his 1231's, any chance there is a release between 7.0.220.0 and 7.1.91.0 that will support both AP's?
View 6 Replies
View Related
