Cisco Wireless :: Convert A 1602i From Lightweight To Autonomous?
Feb 28, 2013how to convert a 1602i AP from lightweight mode to autonomous?
View 3 Replies
ADVERTISEMENT
Cisco Wireless :: AP 2602i - Convert Autonomous AP To Lightweight?
Nov 10, 2012Is it possible to convert an Autonomous AP 2602i to Lightweight just changing firmware as the first generation Aironet APs?
View 2 Replies View RelatedCisco Wireless :: Convert Autonomous 1142N To Lightweight?
Apr 15, 2012Apparently converting autonomous 1142N to lightweight is not supported by ether WCS 7.0 or the Upgrade tool. The option is to do it manually with CLI, but there is about 200+ AP's that need converting. We can't do them all at the same time. We have to do it building per building.
View 4 Replies View RelatedCisco Wireless :: Convert 1041 In Autonomous AP Mode To Lightweight?
Apr 20, 2012Is it possible to convert a 1041 in Autonomous AP mode to Lightweight? Since on the cco page there is no upgrade tool under the 1040 series AP,and also i didnt find any document with the procedure.
View 1 Replies View RelatedCisco Wireless :: 1811W Router - Convert To Lightweight?
Nov 11, 2012We have a couple of smaller remote locations running cisco 1811W routers (built in switch ports & wireless).Now I have been tasked with determining if the wireless portion can be converted to Lightweight or not; if so what is required.
I am running
WCS 7.0.230.0
WLC 5508 (same code)
Cisco Wireless :: Getting Air-lap1042N-E-K9 Lightweight To Autonomous?
Mar 4, 2012I have a air-lap1042-n-e-k9, how to put this wi-fi mode autonomous ?
View 5 Replies View RelatedCisco Wireless :: 3502i Autonomous To Lightweight?
Apr 28, 2013how to convert a 3502 access point from Autonomous to Lightweight ? 3502 has a new IOS released back in Dec 2012 to work as staandalone mode. I need to convert this back to Lightweight mode.
I have been searching on web but have had no luck so far with anything. Tried converting it to lightweight in the same way as putting it on Autonomous IOS but errored out.
Cisco Wireless :: Converting 2602 From Lightweight To Autonomous?
Feb 19, 2013I have a problem converting 2602 from lightweight to autonomous. It will not boot to the autonomous IOS. The procedure below is waht I did.
ap: set IP_ADDR 10.0.0.1
ap: set NETMASK 255.255.255.0
ap: tftp_init
[Code].....
Cisco Wireless :: 1041n From Autonomous To Lightweight - Error
Apr 30, 2012Doing the firmware upgrade on a 1041n AP from Autonomous to Lightweight. Downloaded from Cisco, checked MD5 and got a match so went and upgraded. Upgrade went find etc.. and rebooted. When I reboot I get the following error and then rubbish text
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0xc0000000
RQDC, RFDC : 0x80000037, 0x0000018a
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
[code]...
I rolled back to the autonomous OS and all ok and AP operates as normal. When on the lightweight IOS I can get a telnet response but cannot access as it states Password require but not set.
Followed this process to upgrade [URL] and followed this process to restore to Autonomous: [URL] why it's not working.
Update: Just tried another AP same result. Downloaded Lightweight again and same result
Here is the CLI upgrade process
examining image...
Loading c1140-rcvk9w8-tar.124-21a.JA2.tar .from 172.16.4.114 (via BVI1): !
extracting info (273 bytes)
Image info:
Version Suffix: rcvk9w8-
Image Name: c1140-rcvk9w8-mx
[code]....
Cisco Wireless :: Air-ap1142n-ek9 / Requirements For Autonomous To Lightweight AP Conversion?
May 21, 2012is there any issue in buying air-ap1142n-ek9 802.11A/G/N FIXED AUTO AP INT ANT and later on converting it into lightweight under the control of air-ct2504-15k9 2504 WIRELESS CONTROLLER WITH 15 AP LICENSES ?Are there any requirements on the SW of the WLC and the IOS of the AP? The reason of the choice is budget.
View 1 Replies View RelatedCisco Wireless :: Upgrade AP1262N To LAP1262 Autonomous To Lightweight?
Jul 12, 2012This is one of our first site where we are implementing Cisco wireless, and we bought some external Autonomous AP1262, when we should have bought Lightweight LAP1262 . We can get those replaced, but I am looking into migrating them in order to get them to register with our 5508 controllers.
There do not seem to be a migration tool to download for 1262. Must it be done via the WCS ?So far I have not managed to add these autonomous AP to the controllers. How to know if a migration toll exists for those !
Cisco Wireless :: Bridge Autonomous 1252 AP To Lightweight WLAN
Aug 22, 2011I have a Cisco WLC 5508 managing several 1252s in lightweight mode. There is a portable across campus that has a standalone network but no cabling to tie in to the corporate network. I have another 1252 that is in autonomous mode. Could I essentially configure that as a bridge with the same security and SSID in order to bridge the corporate WLAN? If not, what are my options?
View 4 Replies View RelatedCisco Wireless :: What 113X AP Model Will Work In Autonomous And Lightweight Mode
Feb 4, 2013What 113X AP model will work in Autonomous and LightWeight Mode? I want to buy some 113X AP's for my lab and want to make sure I don't get stuck with the ones that only run in one mode. I am looking at buying this one AIR-AP1131AG-N-K9 802.11a/b/g. Will this model work in both modes?
View 1 Replies View RelatedCisco Wireless :: AIR-AP1231G-E-K9 - Upgrading Autonomous Access Points To Lightweight Mode
Jun 6, 2013I have AP AIR-AP1231G-E-K9 with iOS c1200-k9w7-tar.123-7.JA2 and I want to convert it to Lightweight Mode with iOS image c1200-rcvk9w8 tar.124-21a.JA2. First of all, is it possible? Because I tried to convert from tftp server command (archive download-sw /overwrite /reload tftp://ipaddress/image.tar) and I cannot see in the controller. (controller and aps are in the same network)
View 11 Replies View RelatedCisco Wireless :: Convert Capwap 1142 To Autonomous
Mar 28, 2012I have an 1142 running capwap c1140-k9w8-tar.124-23c.JA4 that I am wanting to convert to an Autonomous AP.However, the AP does not seem to have an archive exec command to tftp downoad an new IOS.Is there another procedure that should be used ?
View 7 Replies View RelatedCisco Wireless :: Convert Aironet 1310 Autonomous To LAP?
Apr 22, 2012Is it possible to also upgrade the 1310 series cisco ap's from autonomous to lwap without using the upgrade tool, if so what procedure do I follow? The upgrade tool required to have telnet enable on the controller which I can't break the policy
View 1 Replies View RelatedCisco Wireless :: Air-lap-1131-ag-e-k9 - How To Convert To Autonomous Mode
May 7, 2013i have a air-lap01131-ag-e-k9 that was originally in lightweight mode and configured with a controller, but i am in the process of wanting to convert to autonomous mode, i am having issues with connectivity to the AP from my laptop.
i have followed numerous guides on this forum, i have successfully
downloaded correct firmware
renamed the firmware to .default
placed this in root of tftp server folder
connected laptop via console to view output
connected laptop via Ethernet to Ethernet port of AP
changed static ip on laptop to 10.0.0.2 set subnet mask to 255.255.255.0, default gateway to 10.0.0.1
held reset button on AP when applying power and waiting for radio light to flash red
AP gets a IP address then of 10.0.0.1
But even though both laptop and AP are in the same subnet, i am unable to ping the AP from my laptop and it doesn't start the tftp process
I have disabled firewall etc, and tried with both crossover and straight through cable, it seems there is something missing at this last stage, i even tried on a second laptop but that would not ping either, am i missing something.
Cisco Wireless :: AP1141 Convert From Autonomous To Lightway
Mar 26, 2012I have an AP 1141N-A-K9, from autonomous system, with this IOS ( c1140-k9w7-mx.124-21a.JA1), and a WLC 5508 with Version 7.X
I want to convert this AP to lightway to use with this controller.
I download de Version of IOS (c1140-rcvk9w8-tar.124-21a.JA2.tar) from cisco and the upgrade tool. but when I start the process in the upgrade tool the result is "this version is not supported by the upgrade tool", it pass all the requested information but show this error at the end.
Cisco :: 1242 Autonomous And / Or Lightweight
Jan 17, 2011I have some 1242s and I can't get a straight answer on whether they can do both autonomous and lightweight or just lightweight.
Model number: AIR-LAP1242AG-A-K9.
I'm assuming that the 'L' in the model numbers means it's just lightweight, but searching Cisco's site and the Internet in general it's just not clear.
I know it works as a lightweight AP, can I run it in autonomous mode?
Cisco Wireless :: How To Convert AIR-AP1041N (autonomous) To AIR-LAP1041N (lwapp)
Sep 11, 2011some days ago I succesfully converted AIR-LAP1041N (lwapp) to AIR-AP1041N (autonomus).I used c1140-k9w7-tar.124-25d.JA1.tar which is available to download in Download Software Section for this AP.But there are any autonomus to lightweigt firmware for this AP.I tried to use c1140-rcvk9w8-tar. 124- 21a.JA2.tar for 1140 but AP hungs after that. How can i back to LWAPP version in 1041?
View 7 Replies View RelatedCisco Wireless :: 1042 - Convert Light Weight AP To Autonomous Mode?
Mar 19, 2012I have 1042 Light weight AP and i want to convert it to Autonomous mode . i dont find any particular image for this conversion ..when i try to find autonomous image for 1040 its showing "c1140-k9w7-tar.124-25d.JA1.tar"........can i use this image ?...
View 1 Replies View RelatedCisco :: Changing AP 1230 And 1231 From Lightweight To Autonomous
Jan 22, 2013I cannot TFTP this tar file to both 1230 and 1231 APs. Both are lightweight APs that I've wiped to the rommon mode (ap>) and I issue the command:
tar -xtract c1200/k9w7-mx.123-8.JA 10.0.0.2
And I get a error saying: "permission denied"
Notes:
The AP has defaulted to the 10.0.0.1 IP.
My laptop is set to 10.0.0.2 255.255.255.0 IP
My TFTP-Server is on and the root folder with the .tar file is in there.
ether_init, flash_init, tftp_init (these commands have been executed)
My firewall is disabled.
Cisco :: Adding 1310 Autonomous AP To WCS Before Upgrade To Lightweight
Jan 30, 2011I keep getting the following error "Could not execute JDBC batch update" when trying to add AP to WCS ... other 1240 APs added without any problems.
View 4 Replies View RelatedCisco Wireless :: AP 1041 Conversion From Autonomous Mode To Lightweight Mode
Mar 4, 2012We have recently converted 1 Cisco Lightweight AP 1041 to Autonomous mode for site-survey purposes. We now want to convert it back to lightweight mode.
View 1 Replies View RelatedCisco WAN :: Convert LAP AIR-AP1121G-E-K9 To Autonomous AP
Feb 27, 2011I want to convert LAP AIR-AP1121G-E-K9 to autonomous AP.
View 1 Replies View RelatedCisco Wireless :: AIR-SAP-1602i-k9 Aironet Standalone Configuration?
Jun 11, 2013I have a AIR-SAP-1602i-k9 Aironet. I cannot find any information on the Cisco site on how to configure the Aironet without a controller. I assumed a standalone meant I could just login.
I tried seeing if it would pull a DHCP address on my network but it didnt.
Cisco Wireless :: 1602i APs - Power Injector Or Adapter?
Jan 28, 2013We are planning a wireless network using the 1602i APs. Some of our APs might or might not be within the 100m limit from the switches, so we'll be running them as repeaters instead. Right now, we are planning on buying power injectors for everything, but I can't seem to find an answer to this question:
If I'm running an AP as a repeater (no ethernet running back to a switch), can it still receive power from a power injector and a short ethernet run between the injector and the AP? Or will I need to use a power adapter?
Cisco Wireless :: 2504 Controller And 1602i APs / Getting Different Error Messages From WLC
Feb 18, 2013i have currently a 2504 WLC and some 1602i AP's.Basically so far i have configured the WLC as per the guidelines on the startup and now i want to join the AP's (which i haven't managed to do yet) and the setup the wireless network.I can get the AP to join and pickup an ip address and that is it. It comes up with different error messages from the WLC, and through hyper terminal, none of which i understand but the main jist is the following:
*spamApTask4: Feb 19 15:05:56.171: #CAPWAP-3-DECODE_ERR: capwap_ac_sm.c:3844 Error decoding Join request from AP 6c:20:56:0e:23:e0
AND
0Tue Feb 19 15:06:19 2013AP with MAC 6c:20:56:0e:23:e0 (AIR-CAP1602I-E-K9 ) is unknown.
AND
Cisco Aironet 1602i - Connect AP To LAN Port On PC To Provide WLAN
Feb 26, 2013I have a PC running my server application and several iPad Clients, and therefore need a WLAN to connect them.
Can I simply plug an access point such as a Cisco Aironet 1602i into the LAN port of the PC to accomplish this?
Cisco Wireless :: 5500 - How Does Lightweight AP Gets Configuration From WLC
Jul 15, 2012Our client have cisco 5500 Wireless lan controllers. They connect to core switch and other ports conenct to various switches on each floor. Then we have cisco AP 1300 series mounted on celing. I was reading that lightweight AP gets config from WLC as soon as they plug in. Need to know how the AP gets config from WLC switches?
View 8 Replies View RelatedCisco Wireless :: Status Led AP 1250 Lightweight?
Sep 16, 2012a few day l have 3 AP Ligthweight 1250, today l was checking my infrastructure and l saw that these 3 AP can´t join to the controller, l reset the AP to the, and its can not join, l checked physicly the AP, and the Ethernet Led is in Amber permanent and the Radio Led is in Green permanet , i am searching the status led to find the fix but l have not found these convination led. and l can not access to the consolo port.
View 2 Replies View RelatedCisco Wireless :: AP 1041N Upgrade To Lightweight Firmware?
Mar 24, 2013How can I upgrade my 1041N AP to lightweight firmware? I found an upgrade tool which works in only XP and 2000 machines. I do not have these outdated OS so is there another way to upgrade it to lightweight?
View 2 Replies View RelatedCisco Wireless :: 1042n Configured As WGB In Lightweight Environment
Nov 8, 2012Here is what I am attempting to do.
1. I have a 1042N AP configured as a Workgroup-Bridge attaching to a Lightweight Access Point.
2. LWAPP AP is on a 5508 series Controller.
3. I have MAC Authentication configured through an Ciso ACS box running 5.2 code. And that portion is working.
4. I want to lock this WGB down even further with a second layer of security. I am thinking WPA2 -AES.