How can I upgrade my 1041N AP to lightweight firmware? I found an upgrade tool which works in only XP and 2000 machines. I do not have these outdated OS so is there another way to upgrade it to lightweight?
View 2 RepliesDoing the firmware upgrade on a 1041n AP from Autonomous to Lightweight. Downloaded from Cisco, checked MD5 and got a match so went and upgraded. Upgrade went find etc.. and rebooted. When I reboot I get the following error and then rubbish text
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0xc0000000
RQDC, RFDC : 0x80000037, 0x0000018a
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
[code]...
I rolled back to the autonomous OS and all ok and AP operates as normal. When on the lightweight IOS I can get a telnet response but cannot access as it states Password require but not set.
Followed this process to upgrade [URL] and followed this process to restore to Autonomous: [URL] why it's not working.
Update: Just tried another AP same result. Downloaded Lightweight again and same result
Here is the CLI upgrade process
examining image...
Loading c1140-rcvk9w8-tar.124-21a.JA2.tar .from 172.16.4.114 (via BVI1): !
extracting info (273 bytes)
Image info:
Version Suffix: rcvk9w8-
Image Name: c1140-rcvk9w8-mx
[code]....
How to upgrade C3502i to Lightweight? I failed to upgrade using Upgrade tool v3.4. The error message is "AP model is not supported" . how can I upgrade it?
View 9 Replies View RelatedThis is one of our first site where we are implementing Cisco wireless, and we bought some external Autonomous AP1262, when we should have bought Lightweight LAP1262 . We can get those replaced, but I am looking into migrating them in order to get them to register with our 5508 controllers.
There do not seem to be a migration tool to download for 1262. Must it be done via the WCS ?So far I have not managed to add these autonomous AP to the controllers. How to know if a migration toll exists for those !
I have a 5508 controller, just upgraded from 6.0.182 to 7.0.98.0. Also LAG was switched off directly after upgrade.
Since the upgrade none of the 1142 LAPs are associating with the controller. I can see they are being issued IPs by the internal DHCP but putting a console cable and watching I am getting:
Not in Bound state.
*May 4 11:41:17.759: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*May 4 11:41:17.759: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
One Ap prior to the upgrade was on a static IP and that connected through without any problem, (it was an 1131 though, but I dont think that is the issue...)
I keep getting the following error "Could not execute JDBC batch update" when trying to add AP to WCS ... other 1240 APs added without any problems.
View 4 Replies View RelatedWe have a pretty good sized church and gym and we're thinking about getting three 1041n to cover the whole area. If we setup all three exactly the same, with the same ssid and password, but just put them on different channels, will our devices automatically hop from ap to ap as we walk around? Is there anything special we should do to make them work better together?
View 1 Replies View RelatedAfter much investigation I finally found what I thought was the firmware upgrade for my WAP4400N access point, I downloaded the file which is a .img file which seems a bit off I think. Anyway when I go to the admin page it decides its an unknown file format. Could someone explain what I am supposed to do with it!
I have to say I am very dissapointed with the whole support function of this site it is very hard to navigate and when you do think you have the correct link, its not. How very helpful!!! I suppose there are networking gurus who look after multi 1000 user systems who understand how the site works and think its fantastic. I support 5 PC's and 7 laptops on top of my normal job, it should be easier.
We have a few AIR-LAP1041N-E-K9 and 2106 controller. One of the 1041N began rebooting in a loop. All over AP work fine. This morning, AP normally loaded at once. Two hours later, after AP reboot, situation repeated itself. Output from console:
using eeprom values
WRDTR,CLKTR: 0x85000800 0xc0000000
RQDC ,RFDC : 0x80000037 0x0000018c
[Code].....
how to enable wireless N speeds on this access point? It's operating in mixed mode via PoE. If I go into network interfaces -> Radio0-802.11N --> Settings, the highest data rate is only 54 mbps. Can N speeds be acheived in mix mode? Also, I thought this access point is dual-band, but I'm only seeing the one radio, is that normal? (see attached image)
View 9 Replies View RelatedI recently purchased a new Cisco 881w router (last Friday).I have configured the 'wired' part of the router with little trouble, but the wireless side is proving a little challenging.I have read a number of posts complaining about the firmware version installed on my device being very buggy.The version of the firmware on the wired part is: Version 15.0(1)M8, however, the firmware on the wireless side seems to be: Version 12.4(21a)JA1 - the version reported as buggy. The former has a version date of 2012, with the latter being 2009.I have tried to download a newer version, but the site is asking me to provide a support contract.I wouldn't mind buying a support contract if the thing worked in the first place and I was trying to add some feature after it had been working for a while.
View 1 Replies View RelatedI get the message "Firmware upgrade has failed. Please ensure that valid entries were specified in the required fields." when I try upgrade the firmware rootfs.bin.
View 4 Replies View RelatedI am in the midst of trying to update the controller firmware of a cisco wireless lan contoller 4402, and having some issues getting the file to transfer to the controller. i am currently running verison 5.0.148 on the controller and attempting to upgrade to the latest version of 7.0.230 and for whatever reason it continues to not transfer. I have tried all 3 methods of cli, gui and using wcs software. all the no avail , I have tried tftp32 and 3cdaemon with the same results.
The error that i am getting from 3cdaemon is got socket timeout aborting code 10054, failing at 66MB transfered. I increased the timeouts both on the wlc and the tftp client to no avail
the error i get on the wlc is Code file transfer failed - Error while writing output file
We have some Cisco Aironet 1142N Autonomous access points installed, currently running 12.4(21a)JA1 IOS system software:
System Software Filename: c1140-k9w7-tar.124-21a.JA1
System Software Version: 12.4(21a)JA1
Bootloader Version: 12.4(23c)JA3
We tried to install the following Autonomous AP IOS software update:
Release 15.2.2-JA ED (c1140-k9w7-tar.152-2.JA.tar) 30-AUG-2012
But the 15.2.2-JA system software release does not install via TFTP Web-GUI (from a accessible PumpKIN TFTP-Server poining on that software update).
What's the problem with that?Is that system software release 15.2.2-JA ED (c1140-k9w7-tar.152-2.JA.tar) not compatible to the Cisco Aironet 1142N Autonomous access points
Hardware configuration:
KurzenPartner_1#show hardware
Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 16-Sep-09 18:09 by prod_rel_team
[code]....
I would like to upgrade the firmware for my WRT54GS V2.1 router however, I only see versions 1.0, 1.1, 2.0, 3.0, etc.. There is no 2.1 listed, so does this mean I can use the v2.0 firmware?
View 3 Replies View RelatedI just purchased a new E1200 router with firmware version 2.0.01 and downloaded the latest version 2.0.03 and tried to install it through the router. When I choose the downloaded file and try to start upgrade I immediately get an error "The Image File is Incorrect". I redownloaded it and tried again with the same error. how to get past this and upgrade the firmware?
View 9 Replies View RelatedThe file uploads fine, but I get an error message saying the router can't be updated atthe moment. I want to do the update because as of now, the router can't see my drive connected on usb (one ntfs partition and another one called wbfs, maybe that one is causing the issue about the drive).
View 2 Replies View RelatedI tried to upgrade my router firmware to the latest 2.1.39.145204 (downloaded from cisco website) but seems like the upgrade didn't go well. I am unable to open the admin webpage. I can get to the login page on 192.168.1.1, after i enter the admin password the next page doesn't load. It keeps showing 'Waiting' at the center of the page forever.. I have tried to do the 30/30/30 reset to no avail, i tried to do tftp downgrade to older firmware version but the tftp boot doesn't even start. Is there any other way i can either fix the current firmware upgrade or downgrade it to the previous version?
View 9 Replies View Related[code]...
This is new EA6500 and The firsttime Setup My EA6500，Download New Ver Linksys Smart Wi-Fi Router Setup,he say Your router was not successfully set up.
I currently have Model name: Linksys E4200 Firmware version: 1.0.04 build 11 Software version: 1.4.12100.0
I'm trying to upgrade to the second and most up to date version. (Version: 2.0) firmware. Any links or way to do this? I tried doing it through my router settings under administration -> firmware upgrade but it won't update automatically. I have to find the actual update file and update the firmware through that.
Region : Romania
Model : TL-WR740N
Hardware Version : V3
Firmware Version : 3.8.2 Build 080628 Rel.37228n
ISP :
I have a problem with my tplink router. In first of all I can't find my model in this forum. I have TL-WR641G [108M] and I cant upgrade my firmware.
My current firmware is:
Firmware version: 3.8.2 Build 080628 Rel.37228n
Hardware Version: WR641G/642G v3 081520C2
I tried to download the latest firmware from this page (V4) [URL] I press browse button from web interface, I select wr641gv4-en-up.bin and I press Upgrade but nothings happened. I read on other forums this router have 1MB internal memory and wr641gv4-en-up.bin have 1.07MB.
I have a WRT110 wireless router which disconnects suddenly and continuously. In addition, its performance is really poor. The current firmware installed is 1.0.03. I found a new firmware for this model (1.0.04.10) but when I try to install it, I choose the .bin file downloaded from Linksys TechSupp website, click on the "Start Upgrade" button, but I always get the following message "Please designate the path to the firmware".
View 9 Replies View RelatedI had issues with my router incorrectly resolving URLs. For example, going to facebook.com would gtive me a "wiki does not exist" message. Pinging facebook.com would give me an IP that belongs to wikipedia. The answer was SUPPOSED to be upgrading to v3.0.03.I upgraded and now my router WILL NOT connect to my DSL modem. Oh, it says it's connected and shows the correct IP address for my DSL modem but the gateway is showing 0.0.0.0. Direct connection to my PC works just fine.I have cycled the power on both the router and the DSL modem several times. The DSL modem is working just fine. I have done several IP release/renew on the router. I have reset the router. To no avail. This firmware update (which completed successfully) seems to have killed my routers ability to communitcate with the internet.
View 4 Replies View RelatedWhen I attempt to upgrade the firmware, I receive error code 0x82BF010E. It wont allow me to complete the firmware upgrade on my Mac OS X (10.7.5)
View 3 Replies View RelatedPS Linksis Online Support said they do not have old firmware andgives me some phones to call .. Others have written about the same problem, saying that prior toupgrade with new firmware to be flash with 2.0.14.I need firmware - version: 2.0.14, where to find it?
View 9 Replies View RelatedModel : TD-W8961ND
Hardware Version : V1
Firmware Version : 100722
ISP : Talk Talk
I've downloaded the firmware update 111125 and followed the instructions. The progress bar reaches 100% but the router doesn't seem to restart (judging by the status lights on the front). It does ask me to log back in but when I check the firmware version, it still reads 100722. I also tried factory default settings after the update. Still it reads 100722. I've tried the update 3 times now.
My Linksys WRT54G router has been dropping out lately and I've been recommended to update its firmware as it is very out-of-date. Well, everytime I try to upgrade the firmware to it, I get an error message that says "the connection to the server was reset while the page was loading." I'm trying to upgrade the firmware through the router's site 192.168.1.1 under the adminstration tab
View 2 Replies View RelatedI am trying to upgrade the firmware, your web site requires the version number, my version is V8, your site offers up to 7.2 ?
View 2 Replies View RelatedI have a wrt54g (8.1) that was acting a little funny so did some googling and followed the instructions to install new firmware. First the installation failed, double checked to make sure I downloaded the correct file (FW_WRT54G_8.1.09.02_US_20071227.bin), did a reset and power cycle. Checked the information again and everything on the router setup completely disappeared.
View 8 Replies View RelatedThere is no “firmware” number after the model and I believe this router has never had a firmware upgrade. However, if I try to download any of the 3 upgrades from the Linksys support site I get the message “firmware not available, sorry for the inconvenience.” Since the suggested solutions to so many problems posted in the forum is to first upgrade the firmware, I find this response with no explanation quite annoying. I am having problems replacing my current hardwired Linksys two port router with the WRK54G wireless 4-port router. Questions regarding that problem I will post under a different topic. For now, how I can get the firmware upgrade for the WRK54G?
View 5 Replies View RelatedMy WAP4410N AP is running version 2.0.2.1 firmware which is quite old. There are newer firmware releases available which I'd like to upgrade to (fix the known bugs, etc.).
So I upgrade my firmware from version 2.0.2.1 to any of the following versions:
- 2.0.3.3
- 2.0.4.2
- 2.0.5.3
The AP reboots and my settings are all still there.
I go to change any of the settings I have - DNS, Time Zone, PSK, any field which can be edited and click Save.
The Save takes place and the screen refreshes to the old settings - the new settings don't stay in place after the Save.
I've also factory defaulted the AP prior to the upgrade, upgraded and then been in the same place unable to save any changed settings.
System details:
Information PID VID: WAP4410N-E V02
Device: WAP4410N Wireless-N Access Point with Power Over Ethernet Software Version: 2.0.2.1
where can I download firmware upgrade for siemens SE572 wireless router
View 2 Replies View RelatedI have tried to upgrade the firmware to the latest greatest but keep getting the "Incorrect image file" error. I bought two of the V1 units and had no trouble with one of them but the other is frustrating me. I have reset it and even tried a tftp upgrade of the firmware but still get "Incorrect image file" even in tftp.
View 1 Replies View Related