I get the message "Firmware upgrade has failed. Please ensure that valid entries were specified in the required fields." when I try upgrade the firmware rootfs.bin.
View 4 RepliesWhen upgrading with .bin file (v1.05.8) via Administration - Firmware Upgrade, it fails when status showing 76% completion.
View 4 Replies View Relatedjust troed to update FIRMWARE re our WRT54G_v2
current FIRMWAREFirmware Version: v3.37.7
downloaded and tried to run 130228dl_LINKSYS_FW_WRT54Gv4_4.21.5.000_20120220.bin
BUT got msg' Upgrade are failed!;
I'm attempting to upgrade to firmware 5.00.38 for my WRT54G-TM router, but it keeps telling me "upgrade failed" after like 3-4 seconds of trying. It says I currently have firmware: DD-WRT v24-sp2 (06/13/09) mega - build 12288. I've tried restetting to factory defaults before upgrading
View 3 Replies View RelatedThe label on my router says "WRT54GS" and the current firmware is 4.71.4.
View 1 Replies View RelatedRegion : UnitedKingdom
Model : TL-WR1042ND
Hardware Version : V1
Firmware Version : 3-14-4 to 3-15-4
ISP : Primus Saver
I had it all working fine, then I wanted to upgrade the firmware. The original firmware was 3-14-4. I downloaded and applied the 3-15-4 firmware. Now when it powers on the power light is on all the time. Immediately the sys, 4, 3, 2, 1, Internet, usb and wps lights flash once. Then about 5 seconds later the 4, 3, 2, 1 & Internet lights flash once, then a second later the cycle starts again. When I connect it to the PC it starts to make a connection on the NIC, but then the router resets. Model: TL-WR1042ND, Ver 1.3 . Is there a way to reset the firmware or get it working again?
I tried to upgrade firmware (I entered my model number WRT54G and hardware version 2 into Cisco menu and downloded the upgrade file they provided. My version was v2.02.7, downloded file FW_WRT54Gv4_4.21.5.000_20120220.bin . After I run the upgrade it said upgrade failed. After that I can't connect to internet and can't access the router. I tried to reset it and unplug it- no luck. From my PC control panel I see local area connections status connected, but as I said, it does not connect to Internet.
View 7 Replies View RelatedI just bought a Cisco E4200 (from someone on Ebay, so returning is probably not an option). I was in the process of setting it up when it wanted to do a Router Update. Unfortunately, it did not specifically say to not do it WIRELESS. We had a disconnection in the upgrade process. Now the Power light just blinks. I can ping it from a hard-wired PC, but cannot get to the Administration Web page to retry the firmware update (I did download it from the site). Also Cisco Connect cannot connect to the router.
Oh Yes, I have tried holding reset button for 30 seconds, unplugging for 30 seconds, and replugging in the router. I do not get any different results.
My router: WRT160Nv3
My Firmware Version: v3.0.02
Upgrade version: Ver.3.0.03 Build 3
I can not upgrade, always gives the same error message: Firmware upgrade failed!
I bought belkin N150 recently. I tried to configure with my ISP. They are surprised how I don't have DHCP option in the wifi configuration and asked me to upgrade my firmware. When I tried to upgrade. I downloaded the firmware from [URL] tried to upgrade. It is showing file format error.
View 2 Replies View RelatedI upgraded the firmware on my wap121 and the URL redirect option is now gone. The docs all talk about using Captive portal but that is only on a wap321. How can I get the redirect back so customers who connect to my network see the site for our bar before they go on the internet?
I upgraded from the 1.0.0.3 to the latest (1.0.2.3)
I just upload firmware1.0.1.10 on 2 WAP121. After the update and reboot, I was able to confirm the firmware version in the System Summary menu. The update is uneventful.However, the functions WDS Bridge and WorkGroup Bridge no longer works on two WAP121:
- For WDS Bridge, when I configure a Remote MAC Address with WPA Encryption and then I click on the Save button, nothing happens there. But it works well when I choose without Encryption.
- For WorkGroup Bridge, when I click on the Save button (even without changing the configuration), I have a message "Certificate file uploaded successfully" and another error message in the background: "error occured for query you send path . device.sync ... "
1.0.0.3 firmware is not available on your site, it is imposible for me to go back.
with TFTP upgrade SRW2xxG4_FW_1.2.3.0.ros and WEB interface after the restart, the switch will not start, display HyperTerminal link. You can also restore the switches do not?
View 1 Replies View RelatedI've tried to upgrade firmware through chrome, but chrome abruptly shut down during upgrade.Since that, I have not even loggin set-up menu which should be shown up putting 192.168.0.1 to make it back. Amber light is just blinking on Power lamp.
View 2 Replies View Relatedfirst one had to get rid of because just wouldn't work with a 3CX server, anyway, I have a DIR-655 A4 factory shipped with 1.32NA I am trying to update the firmware to 1.34NA but it will not let me. It keeps saying Code:
View 6 Replies View RelatedI have a RV220W running 1.0.1.0. When trying to upgrade to 1.0.4.17 I receive an error: "Upgrade failed due to invalid/corrupted firmware".
I found this article: [URL]
I assume I have to do a factory reset then an upgrade in order to upgrade properly.
If I do a backup running 1.0.1.0, then upgrade to 1.0.4.17, then do a restore, would that put me back to 1.0.1.0? I'm trying to avoid configuring the router manually all over again.
I'm attempting to upgrade to firmware 5.00.38 for my WRT54G-TM router, but it keeps telling me "upgrade failed" after like 3-4 seconds of trying. It says I currently have firmware: DD-WRT v24-sp2 (06/13/09) mega - build 12288. I've tried restetting to factory defaults before upgrading, but doesn't work.
View 1 Replies View RelatedI have Firmware Version: v4.21.1 and whenever I try to upgrade it to the latest one it says "Upgrade are failed!"
View 8 Replies View RelatedI've had my WRT54G for a year few now andhave the occasional problem, were I end up powering off the Modem and the WiFibox to get a connection.So having a week of I thought I should tryand update the firmware and see if this solves the problem.I have a WRT54G Ver 2.0 and am running Win7on my main machine with IE9.I Downloaded the firmware update(FW_WRT54G_4.21.4.000_20110712), and while the update was loading I got a errormessage about Update not taken, this was while the Progress bar was about 3/4through, I click OK and waited a while to see if the progress bar moved anymore, butafter 10 min nothing appear to have happen. So I powered the box offand on again.I appear to be able to see my other PC andmy NAS drive but the WiFi and the broadband connect was gone.I reconnected my PC to the Broadband andlooked for a connection, but none that I’ve found seam to work. I found a referenceto a TFTP utility, but all the links on your site appear to be dead, so I haven’tdownload it from anywhere else in case its different to your.
View 9 Replies View RelatedAfter much investigation I finally found what I thought was the firmware upgrade for my WAP4400N access point, I downloaded the file which is a .img file which seems a bit off I think. Anyway when I go to the admin page it decides its an unknown file format. Could someone explain what I am supposed to do with it!
I have to say I am very dissapointed with the whole support function of this site it is very hard to navigate and when you do think you have the correct link, its not. How very helpful!!! I suppose there are networking gurus who look after multi 1000 user systems who understand how the site works and think its fantastic. I support 5 PC's and 7 laptops on top of my normal job, it should be easier.
How can I upgrade my 1041N AP to lightweight firmware? I found an upgrade tool which works in only XP and 2000 machines. I do not have these outdated OS so is there another way to upgrade it to lightweight?
View 2 Replies View RelatedI recently purchased a new Cisco 881w router (last Friday).I have configured the 'wired' part of the router with little trouble, but the wireless side is proving a little challenging.I have read a number of posts complaining about the firmware version installed on my device being very buggy.The version of the firmware on the wired part is: Version 15.0(1)M8, however, the firmware on the wireless side seems to be: Version 12.4(21a)JA1 - the version reported as buggy. The former has a version date of 2012, with the latter being 2009.I have tried to download a newer version, but the site is asking me to provide a support contract.I wouldn't mind buying a support contract if the thing worked in the first place and I was trying to add some feature after it had been working for a while.
View 1 Replies View RelatedI am in the midst of trying to update the controller firmware of a cisco wireless lan contoller 4402, and having some issues getting the file to transfer to the controller. i am currently running verison 5.0.148 on the controller and attempting to upgrade to the latest version of 7.0.230 and for whatever reason it continues to not transfer. I have tried all 3 methods of cli, gui and using wcs software. all the no avail , I have tried tftp32 and 3cdaemon with the same results.
The error that i am getting from 3cdaemon is got socket timeout aborting code 10054, failing at 66MB transfered. I increased the timeouts both on the wlc and the tftp client to no avail
the error i get on the wlc is Code file transfer failed - Error while writing output file
We have some Cisco Aironet 1142N Autonomous access points installed, currently running 12.4(21a)JA1 IOS system software:
System Software Filename: c1140-k9w7-tar.124-21a.JA1
System Software Version: 12.4(21a)JA1
Bootloader Version: 12.4(23c)JA3
We tried to install the following Autonomous AP IOS software update:
Release 15.2.2-JA ED (c1140-k9w7-tar.152-2.JA.tar) 30-AUG-2012
But the 15.2.2-JA system software release does not install via TFTP Web-GUI (from a accessible PumpKIN TFTP-Server poining on that software update).
What's the problem with that?Is that system software release 15.2.2-JA ED (c1140-k9w7-tar.152-2.JA.tar) not compatible to the Cisco Aironet 1142N Autonomous access points
Hardware configuration:
KurzenPartner_1#show hardware
Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 16-Sep-09 18:09 by prod_rel_team
[code]....
i tryed to update my rv120w from 1.0.2.6 to 1.0.4.10 after about 15 minutes i power cycled the router.it now has alternating green power and wireless lignts flashing and router is unresponsive.
it does not give out ip address and not reachable when seeting static ip on cpui have tried the reset button.Can this unit be recoverd somehow?
I just bought an RV220w. My first act was updating th firmware to 1.0.2.4. Unfortunately I was not able to configure the router for vlan purpose 'cause the "Port VLAN" point was missing in the webinterface. I performed several factory reset but it didnt work for me - so I got back to firmware 1.0.1.0.
View 9 Replies View RelatedI would like to upgrade the firmware for my WRT54GS V2.1 router however, I only see versions 1.0, 1.1, 2.0, 3.0, etc.. There is no 2.1 listed, so does this mean I can use the v2.0 firmware?
View 3 Replies View RelatedI just purchased a new E1200 router with firmware version 2.0.01 and downloaded the latest version 2.0.03 and tried to install it through the router. When I choose the downloaded file and try to start upgrade I immediately get an error "The Image File is Incorrect". I redownloaded it and tried again with the same error. how to get past this and upgrade the firmware?
View 9 Replies View RelatedThe file uploads fine, but I get an error message saying the router can't be updated atthe moment. I want to do the update because as of now, the router can't see my drive connected on usb (one ntfs partition and another one called wbfs, maybe that one is causing the issue about the drive).
View 2 Replies View RelatedI tried to upgrade my router firmware to the latest 2.1.39.145204 (downloaded from cisco website) but seems like the upgrade didn't go well. I am unable to open the admin webpage. I can get to the login page on 192.168.1.1, after i enter the admin password the next page doesn't load. It keeps showing 'Waiting' at the center of the page forever.. I have tried to do the 30/30/30 reset to no avail, i tried to do tftp downgrade to older firmware version but the tftp boot doesn't even start. Is there any other way i can either fix the current firmware upgrade or downgrade it to the previous version?
View 9 Replies View Related[code]...
This is new EA6500 and The firsttime Setup My EA6500，Download New Ver Linksys Smart Wi-Fi Router Setup,he say Your router was not successfully set up.
I currently have Model name: Linksys E4200 Firmware version: 1.0.04 build 11 Software version: 1.4.12100.0
I'm trying to upgrade to the second and most up to date version. (Version: 2.0) firmware. Any links or way to do this? I tried doing it through my router settings under administration -> firmware upgrade but it won't update automatically. I have to find the actual update file and update the firmware through that.
Region : Romania
Model : TL-WR740N
Hardware Version : V3
Firmware Version : 3.8.2 Build 080628 Rel.37228n
ISP :
I have a problem with my tplink router. In first of all I can't find my model in this forum. I have TL-WR641G [108M] and I cant upgrade my firmware.
My current firmware is:
Firmware version: 3.8.2 Build 080628 Rel.37228n
Hardware Version: WR641G/642G v3 081520C2
I tried to download the latest firmware from this page (V4) [URL] I press browse button from web interface, I select wr641gv4-en-up.bin and I press Upgrade but nothings happened. I read on other forums this router have 1MB internal memory and wr641gv4-en-up.bin have 1.07MB.