Cisco Wireless :: 1041n From Autonomous To Lightweight - Error
Apr 30, 2012
Doing the firmware upgrade on a 1041n AP from Autonomous to Lightweight. Downloaded from Cisco, checked MD5 and got a match so went and upgraded. Upgrade went find etc.. and rebooted. When I reboot I get the following error and then rubbish text
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0xc0000000
RQDC, RFDC : 0x80000037, 0x0000018a
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
[code]...
I rolled back to the autonomous OS and all ok and AP operates as normal. When on the lightweight IOS I can get a telnet response but cannot access as it states Password require but not set.
Followed this process to upgrade [URL] and followed this process to restore to Autonomous: [URL] why it's not working.
Update: Just tried another AP same result. Downloaded Lightweight again and same result
Here is the CLI upgrade process
examining image...
Loading c1140-rcvk9w8-tar.124-21a.JA2.tar .from 172.16.4.114 (via BVI1): !
extracting info (273 bytes)
Image info:
Version Suffix: rcvk9w8-
Image Name: c1140-rcvk9w8-mx
[code]....
View 1 Replies
ADVERTISEMENT
Mar 24, 2013
How can I upgrade my 1041N AP to lightweight firmware? I found an upgrade tool which works in only XP and 2000 machines. I do not have these outdated OS so is there another way to upgrade it to lightweight?
View 2 Replies
View Related
Mar 4, 2012
I have a air-lap1042-n-e-k9, how to put this wi-fi mode autonomous ?
View 5 Replies
View Related
Apr 28, 2013
how to convert a 3502 access point from Autonomous to Lightweight ? 3502 has a new IOS released back in Dec 2012 to work as staandalone mode. I need to convert this back to Lightweight mode.
I have been searching on web but have had no luck so far with anything. Tried converting it to lightweight in the same way as putting it on Autonomous IOS but errored out.
View 4 Replies
View Related
Feb 28, 2013
how to convert a 1602i AP from lightweight mode to autonomous?
View 3 Replies
View Related
Feb 19, 2013
I have a problem converting 2602 from lightweight to autonomous. It will not boot to the autonomous IOS. The procedure below is waht I did.
ap: set IP_ADDR 10.0.0.1
ap: set NETMASK 255.255.255.0
ap: tftp_init
[Code].....
View 28 Replies
View Related
Nov 10, 2012
Is it possible to convert an Autonomous AP 2602i to Lightweight just changing firmware as the first generation Aironet APs?
View 2 Replies
View Related
Apr 15, 2012
Apparently converting autonomous 1142N to lightweight is not supported by ether WCS 7.0 or the Upgrade tool. The option is to do it manually with CLI, but there is about 200+ AP's that need converting. We can't do them all at the same time. We have to do it building per building.
View 4 Replies
View Related
May 21, 2012
is there any issue in buying air-ap1142n-ek9 802.11A/G/N FIXED AUTO AP INT ANT and later on converting it into lightweight under the control of air-ct2504-15k9 2504 WIRELESS CONTROLLER WITH 15 AP LICENSES ?Are there any requirements on the SW of the WLC and the IOS of the AP? The reason of the choice is budget.
View 1 Replies
View Related
Jul 12, 2012
This is one of our first site where we are implementing Cisco wireless, and we bought some external Autonomous AP1262, when we should have bought Lightweight LAP1262 . We can get those replaced, but I am looking into migrating them in order to get them to register with our 5508 controllers.
There do not seem to be a migration tool to download for 1262. Must it be done via the WCS ?So far I have not managed to add these autonomous AP to the controllers. How to know if a migration toll exists for those !
View 4 Replies
View Related
Aug 22, 2011
I have a Cisco WLC 5508 managing several 1252s in lightweight mode. There is a portable across campus that has a standalone network but no cabling to tie in to the corporate network. I have another 1252 that is in autonomous mode. Could I essentially configure that as a bridge with the same security and SSID in order to bridge the corporate WLAN? If not, what are my options?
View 4 Replies
View Related
Apr 20, 2012
Is it possible to convert a 1041 in Autonomous AP mode to Lightweight? Since on the cco page there is no upgrade tool under the 1040 series AP,and also i didnt find any document with the procedure.
View 1 Replies
View Related
Feb 4, 2013
What 113X AP model will work in Autonomous and LightWeight Mode? I want to buy some 113X AP's for my lab and want to make sure I don't get stuck with the ones that only run in one mode. I am looking at buying this one AIR-AP1131AG-N-K9 802.11a/b/g. Will this model work in both modes?
View 1 Replies
View Related
Jun 6, 2013
I have AP AIR-AP1231G-E-K9 with iOS c1200-k9w7-tar.123-7.JA2 and I want to convert it to Lightweight Mode with iOS image c1200-rcvk9w8 tar.124-21a.JA2. First of all, is it possible? Because I tried to convert from tftp server command (archive download-sw /overwrite /reload tftp://ipaddress/image.tar) and I cannot see in the controller. (controller and aps are in the same network)
View 11 Replies
View Related
Jan 17, 2011
I have some 1242s and I can't get a straight answer on whether they can do both autonomous and lightweight or just lightweight.
Model number: AIR-LAP1242AG-A-K9.
I'm assuming that the 'L' in the model numbers means it's just lightweight, but searching Cisco's site and the Internet in general it's just not clear.
I know it works as a lightweight AP, can I run it in autonomous mode?
View 3 Replies
View Related
Jan 22, 2013
I cannot TFTP this tar file to both 1230 and 1231 APs. Both are lightweight APs that I've wiped to the rommon mode (ap>) and I issue the command:
tar -xtract c1200/k9w7-mx.123-8.JA 10.0.0.2
And I get a error saying: "permission denied"
Notes:
The AP has defaulted to the 10.0.0.1 IP.
My laptop is set to 10.0.0.2 255.255.255.0 IP
My TFTP-Server is on and the root folder with the .tar file is in there.
ether_init, flash_init, tftp_init (these commands have been executed)
My firewall is disabled.
View 18 Replies
View Related
Jan 30, 2011
I keep getting the following error "Could not execute JDBC batch update" when trying to add AP to WCS ... other 1240 APs added without any problems.
View 4 Replies
View Related
Mar 4, 2012
We have recently converted 1 Cisco Lightweight AP 1041 to Autonomous mode for site-survey purposes. We now want to convert it back to lightweight mode.
View 1 Replies
View Related
Jul 9, 2012
I created a LAP Template in NCS to configure some new 1142 LAPs that were installed in a remote office. These LAPs need to be in Flex Connect mode with V LAN support. The template is being applied with partial success on every access point. Details of the partial success say the Flex Connect Parameters fail with the following error.
Provision Failure: { URL}.Object Not Found Exception cannot be cast to [URL]
Am I doing something wrong? The Flex Connect portion of the template has V LAN Support enabled, Native V LAN ID, and the Profile Name- V LAN Mappings configured.
Prime NCS version 1.1.1.24 Access Points are AIR-LAP1142N-A-K9s running 7.2.110.0
View 3 Replies
View Related
Feb 4, 2013
We have a pretty good sized church and gym and we're thinking about getting three 1041n to cover the whole area. If we setup all three exactly the same, with the same ssid and password, but just put them on different channels, will our devices automatically hop from ap to ap as we walk around? Is there anything special we should do to make them work better together?
View 1 Replies
View Related
Jan 24, 2012
We have a few AIR-LAP1041N-E-K9 and 2106 controller. One of the 1041N began rebooting in a loop. All over AP work fine. This morning, AP normally loaded at once. Two hours later, after AP reboot, situation repeated itself. Output from console:
using eeprom values
WRDTR,CLKTR: 0x85000800 0xc0000000
RQDC ,RFDC : 0x80000037 0x0000018c
[Code].....
View 4 Replies
View Related
Apr 4, 2012
how to enable wireless N speeds on this access point? It's operating in mixed mode via PoE. If I go into network interfaces -> Radio0-802.11N --> Settings, the highest data rate is only 54 mbps. Can N speeds be acheived in mix mode? Also, I thought this access point is dual-band, but I'm only seeing the one radio, is that normal? (see attached image)
View 9 Replies
View Related
Jul 19, 2012
I recently bought 6 airo net 1041N standalone access points for a customer of mine. It's an academy of barely 200 students. I'll be installing an access point in every room, to ensure better signal, since they use video for there classes. The reason why i decided to install an access point in every room is because the walls are armed concrete and they had a terrible experience with a past company in which they spend a lot of money for a antenna system that didn't work.These access points will be connected to a switch, which I have to buy also.Every student is going to bring there own laptops in order to connect to the network.
The reason why I'm writing is because I have a few questions to clarify.
1) What is the best position for better signal, top side wall or corner ceiling?
2) How many client mac address filtering can i do per access point?
3)I plan on doing ESSID but can I mac filter clients to a particular access point or should I mac address filter all permitted devices in all access points. The problem is that students come with iPods and phones and as you know on windows they will be able to see the wpa2 key and enter it on the particular UN-authorized device.
4) Any graphic user interface for configuring these access points or do i have to use Cisco IOS(kind of familiar with it)? (I'm used to GUI)
5)How can I configure these access points, through Ethernet browser or do I have to use console port cable?
6)Do I have to use POE injector or can I connect the access points directly to the switch with PoE and QoS?
7)I was planning on buying a small business switch sg100 d-8 but they recommended me that I should use the catalyst 2960 series, which would be best for handling video data? don't have to be much features, just QoS.
8) Can CCp software be used in these access points?
View 9 Replies
View Related
Jul 15, 2012
We are in need to perform a site survey with the Aironet 1041N Access Point.
Upon reviewing the site survey software, it seems you need to use an Aironet adapter. However from what i can tell, all the Aironet adapters are PCMICA cards, which most modern laptops do not have, and the PCMICA cards that do exist don't have drivers for windows 7.
Are there USB adapters w/ Windows 7 drivers that can be used to perform a site survey?
View 2 Replies
View Related
Jan 17, 2013
I have recently purchase Aironet Access Point. I'm pretty new to Cisco systems and what i'm try to do is have the access point broadcast multiple SSIDs lets call them Guest and Admin. My problems is when i config router to have a DHCP address it works perfectly fine but when i assign a static IP it shows all the any connected device as unkown with IP 0.0.0.0. So i'm guessing i will need to setup a dhcp server. Is there a way access point can have its own DHCP server and IP address ( i don't want to use any from my STATIC ip subnet as i dont know alot of empty ones left) like home wifi router where they assign each device an IP like 192.168.0.1. Is this possible?
View 1 Replies
View Related
Feb 9, 2013
I am using AIR-LAP 1041N-A-K9 wireless Accesspoint it was controlled by using the Air-CT2504-k9 Wireless controller. When I tried to connect the access point using Windows 8 machine it was not able to connect
View 8 Replies
View Related
Aug 24, 2012
I purchased a new ap1041n access point. It's the first Cisco I've tried to configure in a long time. I'm trying to get the 802.11n working but it seems to be stuck in 802.11G since I can only get it to go up to 36mb. The radio says its running in mixed mode and I can't figure out if that means b/g or b/g/n. I ran the Express Setup and it didn't seem to work.
View 5 Replies
View Related
Jul 15, 2012
Our client have cisco 5500 Wireless lan controllers. They connect to core switch and other ports conenct to various switches on each floor. Then we have cisco AP 1300 series mounted on celing. I was reading that lightweight AP gets config from WLC as soon as they plug in. Need to know how the AP gets config from WLC switches?
View 8 Replies
View Related
Sep 16, 2012
a few day l have 3 AP Ligthweight 1250, today l was checking my infrastructure and l saw that these 3 AP can´t join to the controller, l reset the AP to the, and its can not join, l checked physicly the AP, and the Ethernet Led is in Amber permanent and the Radio Led is in Green permanet , i am searching the status led to find the fix but l have not found these convination led. and l can not access to the consolo port.
View 2 Replies
View Related
Nov 8, 2012
Here is what I am attempting to do.
1. I have a 1042N AP configured as a Workgroup-Bridge attaching to a Lightweight Access Point.
2. LWAPP AP is on a 5508 series Controller.
3. I have MAC Authentication configured through an Ciso ACS box running 5.2 code. And that portion is working.
4. I want to lock this WGB down even further with a second layer of security. I am thinking WPA2 -AES.
View 2 Replies
View Related
Nov 11, 2012
We have a couple of smaller remote locations running cisco 1811W routers (built in switch ports & wireless).Now I have been tasked with determining if the wireless portion can be converted to Lightweight or not; if so what is required.
I am running
WCS 7.0.230.0
WLC 5508 (same code)
View 3 Replies
View Related
Nov 15, 2011
How to upgrade C3502i to Lightweight? I failed to upgrade using Upgrade tool v3.4. The error message is "AP model is not supported" . how can I upgrade it?
View 9 Replies
View Related
Jan 30, 2013
Is there any difference between AIR-SAP2602-x-K9 with lightweight IOS and AIR-CAP2602-x-K9?
View 3 Replies
View Related
