Cisco Wireless :: 1142 - Lightweight AP Template / Flex Connect Parameters Error
Jul 9, 2012
I created a LAP Template in NCS to configure some new 1142 LAPs that were installed in a remote office. These LAPs need to be in Flex Connect mode with V LAN support. The template is being applied with partial success on every access point. Details of the partial success say the Flex Connect Parameters fail with the following error.
Provision Failure: { URL}.Object Not Found Exception cannot be cast to [URL]
Am I doing something wrong? The Flex Connect portion of the template has V LAN Support enabled, Native V LAN ID, and the Profile Name- V LAN Mappings configured.
Prime NCS version 1.1.1.24 Access Points are AIR-LAP1142N-A-K9s running 7.2.110.0
View 3 Replies
ADVERTISEMENT
Aug 8, 2012
I am trying to apply WLAN template from NCS to two WLCs 5508 and I receive this message."Another WLAN with same SSID and either WPA1/ WPA2/ WPA1+WPA2 is enabled. Please change the Layer 2 security policy."The template has layer 2 security with WPA+WPA2 enable and 802.1x.I have other WLAN template with other name and other SSID with the same security policies with no problem to apply.
View 2 Replies
View Related
Apr 30, 2012
Doing the firmware upgrade on a 1041n AP from Autonomous to Lightweight. Downloaded from Cisco, checked MD5 and got a match so went and upgraded. Upgrade went find etc.. and rebooted. When I reboot I get the following error and then rubbish text
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0xc0000000
RQDC, RFDC : 0x80000037, 0x0000018a
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
[code]...
I rolled back to the autonomous OS and all ok and AP operates as normal. When on the lightweight IOS I can get a telnet response but cannot access as it states Password require but not set.
Followed this process to upgrade [URL] and followed this process to restore to Autonomous: [URL] why it's not working.
Update: Just tried another AP same result. Downloaded Lightweight again and same result
Here is the CLI upgrade process
examining image...
Loading c1140-rcvk9w8-tar.124-21a.JA2.tar .from 172.16.4.114 (via BVI1): !
extracting info (273 bytes)
Image info:
Version Suffix: rcvk9w8-
Image Name: c1140-rcvk9w8-mx
[code]....
View 1 Replies
View Related
Sep 29, 2012
I have a wireless 5508 with license base to 50 aps, i use a deployment flex connect. I already registered all my access points, I use web authentication to authenticate users guest, and the service dhcp is in the central site.
My issue is the users in each remote site, can not get an ip address by dhcp from the central site, they can authenticate in the guest ssid, but any users can not get an ip. The request is passing by the wan in this way
Central Site DHCP - Router WAN - Remote Site - Users with notebooks. I use flex connect central deployment (all the traffic consulting to the wlc) .
perhaps i should use local deploy? The wireless is in the central site.
View 17 Replies
View Related
Feb 15, 2013
We are planning to implement Cisco wireless in our central office and branch office using Cisco 2504 WLC and Cisco 1602i Ap. Our branch office is connected via ip vpn and a separate broadband connection for urgent requirements. Usually all users are allowed to browse through central proxy server.I have been trying to find any possibility of giving guest access (web authentication) for branch office guests utilizing only the broadband connection which is connected to the branch office. Is there a possibility that Central WLC is reached using NAT from the BranchOffice AP and allowing guests to authenticate and surf the web at times IP VPN is unreachable.
View 4 Replies
View Related
May 22, 2013
I have one cisco wlc 2112 with ios 7.0.230.0 with license to support 12 access points. My access points are nine (9) lap1231ag and one (1) lap1310.I just have one wlan (ssid). My scenario of deployment is in layer 3. I have one interface management and ap manager in the WLC. All my Access Points have differents ip address that WLC. I need to configure a unique ssid to associate my six (6) dynamics interfaces (each dymanic interface with different vlan subnet).Each wlan profile (ssid) should have the same security in phase 2 (wpa2/psk). My cisco access points don't support hreap. My wlc support only (4) interface into an interface group, and i need six (6) dynamics interfaces.
View 6 Replies
View Related
Mar 18, 2013
I had configured one access point CAP3602E in flex connect mode through a WLC 5508 after deploying the access point in flex control mode the local mac-filering is not working. before it was working when ap was in local mode. any body have to know is the mac-filtering working in flex-control mode ?
View 2 Replies
View Related
Aug 22, 2012
As per my understanding, Cisco Nexus 2232 can only connect to HP c7000 Chassis if we are using a Pass Through Switch in the HP c7000. Cisco Nexus 2232 can only connect to End Hosts and not to a switch. Is there a New Feature added in Nexus 2232, which enables it to connect to a Switch like HP Flex Fabric ?
View 1 Replies
View Related
Aug 26, 2012
i have a problem using my usb to serial cable connection, i can connect to one router on my work, but i can't connect to AP 1142, (i have tested also con AP 1231).i have a laptop running windows 7 64 bits, before i use a win xp 32 bits, and i didn't have problems.i am using putty, and have installed tera term 4.74 but the same.connection details, 9600, 8, 1, N, N.
View 5 Replies
View Related
Dec 10, 2012
What's wrong with this config ? Clients can see the wireless ssid's but cant connect.
View 1 Replies
View Related
Feb 29, 2012
I have looked through some posts on here of other people having the same trouble, I tried doing the different things suggested and it still is not working.Laptops/desktops can connect to the open SSID perfect, but anything portable such as iPads, Kindles, Phones etc.do not ever get an IP.I'm remotely troubleshooting this issue for a customer and have SSH ability.
View 9 Replies
View Related
Sep 9, 2012
I am tryign to set up an Aironet 1142, I have created a reserrvation in DHCP using the MAC address, and the reservation shows as active, but I cannot connect to the device with my browser.
View 1 Replies
View Related
Jun 17, 2012
Flex 7500
Software Version: 7.2.103.0
I have a Flex 7500 with 200 1142AP's working fine in remote office and local setup. We have since purchased 3 OEAP 602's and looking to distribute to teleworkers.
I have configured the OEAP to point to the NAT'd IP of the WLC, the OEAP does connect and is listed briefly in the WLC wireless listing but I am not able to make any configuration changes, it will then dissassociate and try the join process all over again. I have attached below the OEAP 600 event log. I see that the WLC does not support data DTLS encryption and looking to make this work.
I have tried to install the DTLS license file from the Cisco website, but says license failed to install, with no other errors.
*Jun 18 15:18:43.938: Build version 7.0.112.72 (compiled Feb 3 2012 at 01:56:39, [L]).
*Jun 18 15:18:47.859: CAPWAP State: Init.
*Jun 18 15:18:47.860: CAPWAP State: Discovery.
[Code]....
View 2 Replies
View Related
Dec 3, 2011
I am planning an HREAP deployment; a data centre with multiple remote sites. HREAP has been evaluated and meets our requirements. We are now looking at buying some equipment for this deployment. For controllers, we are considering either the 5508 or the new 7500. Other than cost, scalability and different hardware what are the differences between the platforms? So far I have found:AP's in local mode not supported on 7500, the 5508 supports AP's in local mode.The 7500 cannot be used as a guest anchor controller, the 5508 can.
View 3 Replies
View Related
Feb 5, 2012
Just want to know if it is possible to have a 7500 Flex Controller Cluster in different Locations, like Germany an Australia?
This should be deployed as a redundant system, in case of a failure in one location the remaining Cluster can take over. Also the main maintenance/management should be done in the Headquarter (Germany). Is it possible to configure Guest Access via Web Interface.
Last question: how many AP`s can be managed, example: with one Controller 500 AP can I then manage 1000 with two controller?
View 4 Replies
View Related
Oct 24, 2012
a customer has bought a new AP 3500 with external antennas and he would like use his old antenna AIR-ANT2485P-R.
We have the option to configure the antenna parameter in WLC under Wireless > Access Points > Radios > 802.11a/n or 802.11b/g/n for external antenna and and using only port A.
But if we enable only one port (Example: port A) we will get a warning message: Need to have at least both dual mode antennas (antennas A and B) enabled
Is it not possible to use an antenna like ANT2485P-N together with an Access Point like 3502E?
View 6 Replies
View Related
May 11, 2011
I just bought a DIR 615 (firmware 4.0) which I am using as an access point linked to a Netopia router. The Netopia has QoS enabled and needs to keep it, however I was hoping to use the DIR615 without QoS. I am using a ReadyNas Duo as storage for music, videos etc.Now, here are my issues which I think are all linked.
1) I have a very slow connection wireless, between 1'500 and 2'000kbits/sec download. This was not the case with my very old Linksys router
2) When I try to rip a CD from iTunes to the NAS, it brings up error messages of lost connection and impossibility to rip in the middle of the songs. I did not have that problem with the Linksys router neither.
3) I would like to change the QoS parameters to see how it affects this connection issue, as well as change other Wifi parameters, but they show up as greyed out and I can't change them. (I feel that the DIR 615 might inherit some parameters from the main router, since it is used as an Access Point).
View 4 Replies
View Related
Jan 8, 2013
I have a 2500 and I have successfully joined a 1600 AP to it; however I have noticed that I cannot enable CleanAir in the Global Parameters with just the 1602 AP joined. This feature was enable when I had my 2602 AP connected.So, is the problem that the 1602 doesn't fully support CleanAir? If that is the case, how do I enable CleanAir Express or is that something you can even enable thru the GUI?
View 9 Replies
View Related
Jun 11, 2013
I attempted to assign a User Roles template to a## 2504 controller and if failed with message stating controller version not supported. My current WCS version is 7.0172, if I upgrade to the lastest version will that resolve the template issue?
View 4 Replies
View Related
Apr 12, 2012
We are trying to get the waep template (default no changes) from the Cisco WebAuth bundle to work on a 5508 controller.
We've setup the controller to use the custom login.tar that comes with the waep template folder in the bundle. We setup the WLAN to work off the global template and we used the config network web-auth secureweb disable command to allow only http rather than https (which is supposed to work in 7.2 code)
When we test with the custom bundle, we get no answer from the controller, just a url of [URL]
If we turn custom off, and use internal everything works...
Just to be clear.. we aren't looking for authentication (user and pass) we are trying to do the enter your email and click accept to the aup method.
View 5 Replies
View Related
Apr 16, 2013
I have an iPad 4 (6.1.3) that won't connect to our Cisco 1142 APs. Full Cisco network; 3560 POE switches on edge and Cisco 6509 at the core.At first we looked at it as a wireless issue. No settings changes on the APs would allow the iPad connect. About 125 other iPads of various models worked fine. Took the offending iPad to McDonalds and it connects fine. Took the offending iPad to another school in our District and it connected and worked fine. Went back to the home school, still won't connect. Contacted Apple since iPad was under warranty, sent it to them and they ran diagnostics and it is fine.Is there anyway that the core switch is blocking the iPad client?
View 1 Replies
View Related
Jul 15, 2012
I have to setup my first flex stack and wanted to make sure I do it right. I have the physical aspect of the stack down. From what I gathered I have to setup the master switch as the highest priority and then provision the other two switches. But I have configs on the other two switches, do I have to delete them? And do I have to setup individual ips for the two slave switches, because from what I saw the master switch is the only one with an ip address? The master switch is a poe 2960S-48LPS and the two other switches are 2960G-48TD
View 5 Replies
View Related
Mar 29, 2012
What is the maximum number of supported RADIUS servers on the Flex 7500 Cloud Controller?
View 2 Replies
View Related
Apr 24, 2013
One of my customer has an Apple IPAD 2.The IPAD is getting registerd through Cisco WLC 7.2.The APs that are being used is AP 1252 & AP 1242. The AP are configured in flex mode. The issue that we are facing is all the laptops and IPADs other then Apple IPAD are working but the Apple IPAD are not working through AES WPA2.It gives him a dismiss message and at time it gets connected but take a long time to get connected. Incase when the IPAD gets connected the following happens.
While connecting to the SSID it will ask for the preshared keyAfetr entering the preshared key it takes time to acquire an IP addressAfter the IP address is assigned it gives a dismiss message. If we do not click on the dismiss message then it will take anothere 30 seconds or so and get connected.
View 1 Replies
View Related
Jul 15, 2012
Our client have cisco 5500 Wireless lan controllers. They connect to core switch and other ports conenct to various switches on each floor. Then we have cisco AP 1300 series mounted on celing. I was reading that lightweight AP gets config from WLC as soon as they plug in. Need to know how the AP gets config from WLC switches?
View 8 Replies
View Related
Mar 4, 2012
I have a air-lap1042-n-e-k9, how to put this wi-fi mode autonomous ?
View 5 Replies
View Related
Sep 16, 2012
a few day l have 3 AP Ligthweight 1250, today l was checking my infrastructure and l saw that these 3 AP can´t join to the controller, l reset the AP to the, and its can not join, l checked physicly the AP, and the Ethernet Led is in Amber permanent and the Radio Led is in Green permanet , i am searching the status led to find the fix but l have not found these convination led. and l can not access to the consolo port.
View 2 Replies
View Related
Apr 28, 2013
how to convert a 3502 access point from Autonomous to Lightweight ? 3502 has a new IOS released back in Dec 2012 to work as staandalone mode. I need to convert this back to Lightweight mode.
I have been searching on web but have had no luck so far with anything. Tried converting it to lightweight in the same way as putting it on Autonomous IOS but errored out.
View 4 Replies
View Related
Mar 17, 2013
I have configured SSL offloading and redirection on a 4710 appliance. Everything works fine. The issue I am facing is that some parameters in url are getting lost.
I have https://%h/%p configured as a redirect server which works fine as far as hostname and path is concerned. i.e. full hostname and path are preserved, but that there are some parameters after the full path in encrypted format which are getting lost. I think 307 redirect can resolve this issue but ACE does not support that.
View 4 Replies
View Related
Oct 16, 2011
I configure two WIC-1DSU-T1-v2 interfaces with a T1 crossover cable. What are the mimimum configurations to do to communicate from LAN1 (int fa0/0 of one 1841 router) to LAN2 (int fa0/0 of the second 1841 router) ?
Do I need a routage protocole ? And if yes wich one ? Interne or externe (RIP or BGP) Or static route is enough ? Also, is that I should put a encapsulation, like ppp ? Is it neccessary on a point to point line ?
Finally what about the following commands, do I need it ?
service-module t1 clock source internal
service-module t1 timeslots 1-24 speed 64
service-module t1 framing esf
service-module t1 linecode b8zs
View 4 Replies
View Related
Feb 28, 2013
how to convert a 1602i AP from lightweight mode to autonomous?
View 3 Replies
View Related
Feb 19, 2013
I have a problem converting 2602 from lightweight to autonomous. It will not boot to the autonomous IOS. The procedure below is waht I did.
ap: set IP_ADDR 10.0.0.1
ap: set NETMASK 255.255.255.0
ap: tftp_init
[Code].....
View 28 Replies
View Related
Mar 24, 2013
How can I upgrade my 1041N AP to lightweight firmware? I found an upgrade tool which works in only XP and 2000 machines. I do not have these outdated OS so is there another way to upgrade it to lightweight?
View 2 Replies
View Related