I am trying to apply WLAN template from NCS to two WLCs 5508 and I receive this message."Another WLAN with same SSID and either WPA1/ WPA2/ WPA1+WPA2 is enabled. Please change the Layer 2 security policy."The template has layer 2 security with WPA+WPA2 enable and 802.1x.I have other WLAN template with other name and other SSID with the same security policies with no problem to apply.
View 2 RepliesWe are trying to get the waep template (default no changes) from the Cisco WebAuth bundle to work on a 5508 controller.
We've setup the controller to use the custom login.tar that comes with the waep template folder in the bundle. We setup the WLAN to work off the global template and we used the config network web-auth secureweb disable command to allow only http rather than https (which is supposed to work in 7.2 code)
When we test with the custom bundle, we get no answer from the controller, just a url of [URL]
If we turn custom off, and use internal everything works...
Just to be clear.. we aren't looking for authentication (user and pass) we are trying to do the enter your email and click accept to the aup method.
I created a LAP Template in NCS to configure some new 1142 LAPs that were installed in a remote office. These LAPs need to be in Flex Connect mode with V LAN support. The template is being applied with partial success on every access point. Details of the partial success say the Flex Connect Parameters fail with the following error.
Provision Failure: { URL}.Object Not Found Exception cannot be cast to [URL]
Am I doing something wrong? The Flex Connect portion of the template has V LAN Support enabled, Native V LAN ID, and the Profile Name- V LAN Mappings configured.
Prime NCS version 1.1.1.24 Access Points are AIR-LAP1142N-A-K9s running 7.2.110.0
I have a WLC 5508 with half a dozen LAPs (AIR-CAP3502I-E-K9).They have been working but sometimes clients detect conectivity problems with the wlan.Here is the message log I can obtain from the controller:
View 1 Replies View RelatedIs there any way to determine how much bandwith users on a particular WLAN (Guest) are using on the 5508 or by any other means?
View 9 Replies View RelatedWe’ve recently installed a 5508 w LAN controller for my organization wireless network and each time devices connect to this wireless network they receive an ip conflict error. All devices conflict with the ip address of IP address 0.0.0.0 with mac address 00-00-00-00-00-00.
All devices event viewer has this TCP error: “The system detected an address conflict for IP address 0.0.0.0 with the system having network hardware address 00-00-00-00-00-00. Network operations on this system may be disrupted as a result.” We previously experienced the same ip conflict with 12000 w LAN network that he had used as proof of concept.
On a wlc 5508-7.0.116, can I set up 2 ssids that map to one wlan/vlan/subnet. I thought you could but I don't have the means to test without breaking production.
My goal is this:
Ssid red open
Ssid blue wpa 2
But all clients on the same ip subnet
I have Cisco 5508 Wlan Controller Software version 7.2.103.0 and I have Cisco AIR-CAP3602I-E-K9 Lightweight Access Points network and its working fine now I want to configure the Repeater in this network. Because there is one area we cannot layout the cable. How to add the repeater and how to configure the repeater in wlan controller network.
Do i need the change the software of Wlan Controller to support Mesh Network or this version 7.2.103.0 can support the repeater because for 1 access point i dont want to upgrade the version.
I have 350 WAP (1142n) running of two WLC 5508 (IOS version 7). WLCs are not located on the same subnets/locations and are not configured as mobility groups. The vlan ids on both wlcs are not identical.
[Code].....
I've got a couple new 5508 controllers to replace my 4404's. Im wondering though if I throw them on the network to setup, will there be any conflict with the current access points? Will they try and join the new controllers for any reason automatically? Is there a better way, or a best practice to provision these new controllers?
View 3 Replies View RelatedI have Cisco 5508 WLAN controller v7.4 and i have lap 1310 and it is not joining to this lan controller. What to do? How to join this lap to this lan controller? or how to convert it to autonomous because i dont find mode button on this access point?
View 6 Replies View RelatedI have Cisco 5508 Wlan Controller and its having 6 Fiber Ports and I have AIR-LAP1131AG-E-K9 Access Point. Can this Access Point will work with this Lan Controller? Can i connect 3 switches to this wlan controller?
View 1 Replies View RelatedI have a wlc 5508 and I'd like to setup a network for visitors. They will connect to the WLAN, enter a password and then automatically get redirected to an external website. I understand the wlc 5508 supports this but I'm struggling to find out how to set this up I assume this can be done without having to customise webauth bundles?
View 2 Replies View RelatedI've seen a discussion about importing mac addresses into the mac filter db on a cisco controller but is there a way to export the mac filter db? I have a Cisco 5508.
View 2 Replies View RelatedI would like to set a time limit for how long a client can be continously connected to the WLAN that provides my guest internet access. The user name/password is hosted on my ACS and authentication is provided by my Cisco NAC. I am using 5508 controllers (7.02) and WCS.
Somewhere in this combination of stuff, there has to be a way to set a two hour time limit.
We have 5508 controller (redundant) & would like to configure Staff vlan to get authenticate with active directory.i am new to the controller device & want to configure controller with active directory (windows 2012).
5508 controller (Active & Standby) with 48 Access Point.(configuration Done) Guest Vlan (only for internet Access) controller based web authentication configured.
Staff Vlan ( inside & outside ). Need to configure with LDAP authentication?
What is the latest IOS version for the WLan Controller 5508 ?
Actually I am using, Software Version7.3.102.0
I see the following at Cisco website:
Latest Releases
7.2.115.1(ED)7.3.112.0(ED)
7.0.240.0(ED)
7.4.100.0(ED)
We had our wireless mesh network running with 4400 Controller and 1510 A.Ps. Now that we have bought new 5508 Controller (with SW: 7.2) and 3600 Indoor APs, we are unable to add legacy APs on our new controller. After a wild googling I have found that for 1510 APs i need to be on SW ver: 4.0. But that will lead into another situation i-e I wont be able to have my 3600 APs on WLAN Controller.
View 1 Replies View RelatedWe have some older Honeywell Dolphin 7900 Series Handhelds that have issues with wireless communication. Very unreliable communication. One recommendation from Honeywell is to disable the G standard and only allow B. Basically have a WLAN that is solely b radio enabled. I see that their are options to go B/G only or A only, but no options in the radio policy to go B only.
We are using WCS 7.0.240 and the controller is a WLC 5508 running the same code revision.
Is this doable on a single WLAN while leaving G available on other WLAN's?
We use WLC 5508 with 7.4. We tried to set max allowed clients per AP radio to 30 through GUI. We have APs with 80 clients associeted though.
When entering config wlan max-associated-clients max-clients wlan-id we got
"WLAN/Guest-Lan/remote-lan is enabled. disable to configure max associated clients."
GUI doesn't show that message, should it? In GUI, Is it necesary to disable WLAN before too?
I've been asked to create 2 wireless networks for guest access. They are to be used by clients of 2 different companies and they have asked for the website of each company to automatically open as a landing page. e.g.
-WLAN1 - password is companyname1 - landing page = www.companyname1.com
-WLAN2 - password is companyname2 - landing page = www.companyname2.com
Is this possible with our 5508 WLC? I have googled it and can see that you can set a web auth page but I need different landing pages depending on which WLAN is connected to.
Is it possible to use Cisco Band Select on a Cisco 5508 WLAN controller and still disable the 802.11b data rates?
View 2 Replies View RelatedSince I moved our WLC Controller ( 5508 ) from Version 7.0 to Version 7.2.111.3 I got above failure messages. Until now I changed the radius timeout from 2 to 10 seconds and also I disabled the aggressive failover without success. What else it could be ?
View 3 Replies View RelatedWe're looking at deploying both office extend and also a guest wlan. Both would require a WLC in the DMZ.My question is can one 5508 WLC be both a guest anchor and have office extend APs on it at the same time?
View 2 Replies View RelatedLooking to add time of day restrictions to our Guest WLAN that is currently in its pilot phase.
Is there a way to config time of day access to a WLAN ?
I have cisco 5508 wlan controller with 8 ports can i connect 8 switches on these port. If i connect what will be configuration to work all these ports because only port 1 is working if i connect to switch remaining ports when i connect status showing is enable but not working.
View 2 Replies View RelatedWe are planning a WLAN upgrade and the security policy is to forward wireless Guest user traffic to the DMZ controllers. We are now considering the Virtual WLAN Controller and all AP's will register with the virtual controllers and we will use Flexconnect for Staff and internal traffic that will switch their traffic onto the local switch.
We wish to forward the guest traffic to the DMZ Guest Anchor controller which will be a 5508 controller. This will also offer Office Extend AP service.I have looked at teh virtual controller docs and not very clear if this deployment model is supported. Below is a diagram of what we wish to deploy and is this a supported deployment model.
I wanto delete the Evalution License and i want to activate the permanent license. find the attached snapshot of License.
View 7 Replies View RelatedI want to setup a webpage for my guest network (no authentication) users. When the client connects to the open guest network and upon opening a browser they would be directed to a survey that I would like them to take, if they don't want to take it they can begin browsing to other sites without issue. How do I do this on a my 5508 WLC?
View 12 Replies View RelatedI have Cisco AIR-LAP1310G-E-K9 access point and 5508 wlan controller with version 7.0.220 and it is joining to the WLAN controller. I have enabled dhcp in the lan controller and i dont have external dns server. How to fix this issue? Can this LAN controller version will support this access point? My Lan Controller Management IP Address is 10.10.10.5 find the below configuration of 1300 access point.
AP001d.4513.dd68#reloadProceed with reload? [confirm]
%SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload Command.%LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file system is available.flashfs[0]: 4 files, 2 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 7741440flashfs[0]: Bytes used: 2052608flashfs[0]: Bytes available: 5688832flashfs[0]: flashfs fsck took 14 seconds.Base ethernet MAC Address: 00:1d:45:13:dd:68Initializing ethernet port 0...Reset ethernet port 0...Reset done!ethernet link up, 100 mbps,
[code].....
When a guest user first trys to access the "guest" WLAN, they are presented with a "certificate page" before the web athentication page / login is presented. The WLC forces an internal redirect to https://1.1.1.1 causing the certificate page to appear. Can this be bypassed? I am runiing 5508 with 7.0.220.0.
View 12 Replies View RelatedSince the SW upgrade to version 7.3.101.0 (wlc 5508) i have the following issue. We have a W LAN with 802.1x (WPA2/AES) secured. Before the update the users need to enter user/ PW every time when they reconnect (W LAN switch off/ on again) to the W LAN. Now the users don`t need to enter user/ PW when they reconnect to the WLAN.
I could not find any setting on wlc to clear this issue.
I am tryign to join my first AP to the 5508 and am gettign this error int he logs.
*Dec 07 10:42:31.067: %DTL-3-NPUARP_ADD_FAILED: dtl_arp.c:2280 Unable to add an ARP entry for 0:0.0.0 to the network processor. entry does not exist
The management Interface is on the the same vlan as the AP , both untagged ports. the AP gets an ip address from my dhcp server.