We have a couple of smaller remote locations running cisco 1811W routers (built in switch ports & wireless).Now I have been tasked with determining if the wireless portion can be converted to Lightweight or not; if so what is required.
I am running
WCS 7.0.230.0
WLC 5508 (same code)
how to convert a 1602i AP from lightweight mode to autonomous?
View 3 Replies View RelatedIs it possible to convert an Autonomous AP 2602i to Lightweight just changing firmware as the first generation Aironet APs?
View 2 Replies View RelatedApparently converting autonomous 1142N to lightweight is not supported by ether WCS 7.0 or the Upgrade tool. The option is to do it manually with CLI, but there is about 200+ AP's that need converting. We can't do them all at the same time. We have to do it building per building.
View 4 Replies View RelatedIs it possible to convert a 1041 in Autonomous AP mode to Lightweight? Since on the cco page there is no upgrade tool under the 1040 series AP,and also i didnt find any document with the procedure.
View 1 Replies View RelatedNeed basic wireless configuration for a SOHO Cisco 1811W router? I just need the wireless to connect to the base wired LAN - with both WEP and MAC authentication. And - can the MAC auth. parameters be configured via CLI and not have to use either SDM or CP? I can access the router via SDM - but the Wirless Application will not fire up - and CP doesn't work at all.
View 18 Replies View RelatedI am setting up 1811w router for accessing internet.DHCP is configured on it but it is not providing IP to laptop connected on port fa6. [code]
View 3 Replies View RelatedNeed to confirm purpose of command below
dot11 ssid TEST
vlan 4
authentication open
authentication key-management wpa
guest-mode ?????
Why we need guest-mode command in above config?
I have an 1811w router and can not figure out how to access the settings of the router. I do not have a console port that I can use to access the settings that way so I want to know how to do it using the SDM. I thought I was following the directions but for some reason when I connect my computer to one of the routers LAN ports no connection is recognized on either the router or the computer. How do I go about connecting to the router and accessing the settings?
View 1 Replies View RelatedOn 1811W Router i have OSPF running and i do not need this static route.ip route 192.168.20.0 255.255.255.0 192.168.20.3,when i try to delete i get error ,1811w#,config t,Enter configuration commands, one per line. End with CNTL/Z.,1811w(config)#no ip route 192.168.20.0 255.255.255.0 192.168.20.3,%No matching route to delete,1811w(config)#.
View 7 Replies View RelatedWireless is working ok on 1811W.Need to know from command output below what values are considered good for power and signal strenghts
1811w#sh dot11 associations all-client
Address : 40fc.894e.c48c Name : NONE
IP Address : 192.168.98.2 Interface : Dot11Radio0
Device : unknown Software Version : NONE
[code].....
Also what is Association ID mean in above output?
I have an ADSL router like the one showed below & internet from the provider via a RJ45 cable.
I need to share the incoming internet from the RJ45 cable to the remaining three RJ45s & over the wireless. How to configure the router to get this working?
Also the internet provider needs me to authenticate via their default webpage before I can access the internet & I can say it doesn't have any MAC binding.
How do I convert my wireless router to a wireless AP (Access Point)?While connected to the main router go Start then Run in XP - (Windows key plus R in Vista and Windows 7), then type in the following, including all the spaces:- cmd /k ipconfig /all -- then press Enter and from the black form that shows up, take a note of the numeric code beside the word "gateway" -- usually something like 192.168.0.1. Type exit to close the black form.Now connect the router to be converted only to a computer via network cable and log in Setup the wireless security Disable the DHCP and change the LAN IP to match the gateway IP but ending in something like .253 Finally connect one of the four LAN ports of the AP to the main router, do NOT use the WAN port.
View 4 Replies View RelatedI have a Cisco 1811W that after several years in service suddenly stopped allowing any wireless connection to laptops on the domain. It allows hard wired connections and devices that are just using the wireless hot spot like iPads and Iphones but not devices on the domain. These same laptops connect wirelessly without issue at our other facilities which use the same hardware.
Here is the config file of the router in question...
router#show run
Building configuration...
Current configuration : 11776 bytes
[Code].....
I have a Belkin f5d7234-4 lying around at home. I also have a Panasonic TV which requires a proprietary wifi donge to get a wireless signal, so my question is, can I use the router to recieve my house Wifi (broadcast by my new NetGear Router) and send it out through its Ethernet port to the TV?
I checked, the router doesn't have ddwrt support, I'm new to hacking around with routers and networks, so I don't know how to do this, I see how it is logically possible
I just switched over from AT&T Uverse to time Warner cable for Internet. I bought a Motorola Surfboard sbg6580. I have the surfboard hooked up and all is well. Now I would like to do in put the old 2wire from AT&T in a room upstairs and use it as place I can plug in the Ethernet cords and also transmit another signal. I have what's a called plug link that is plugged in down stairs and then another upstairs and it allows the Internet signal to run through the power lines. So it just about the equivalent of running a cord for down stairs to upstairs. So basically I just need to plug more then 1 thing upstairs that isn't wireless and I would also like to transmit a 2.4ghz signal upstairs and use my Motorola to transmit a 5ghz.How would I set up the 2wire to do this.
View 3 Replies View RelatedOur client have cisco 5500 Wireless lan controllers. They connect to core switch and other ports conenct to various switches on each floor. Then we have cisco AP 1300 series mounted on celing. I was reading that lightweight AP gets config from WLC as soon as they plug in. Need to know how the AP gets config from WLC switches?
View 8 Replies View RelatedI have a air-lap1042-n-e-k9, how to put this wi-fi mode autonomous ?
View 5 Replies View Relateda few day l have 3 AP Ligthweight 1250, today l was checking my infrastructure and l saw that these 3 AP can´t join to the controller, l reset the AP to the, and its can not join, l checked physicly the AP, and the Ethernet Led is in Amber permanent and the Radio Led is in Green permanet , i am searching the status led to find the fix but l have not found these convination led. and l can not access to the consolo port.
View 2 Replies View Relatedhow to convert a 3502 access point from Autonomous to Lightweight ? 3502 has a new IOS released back in Dec 2012 to work as staandalone mode. I need to convert this back to Lightweight mode.
I have been searching on web but have had no luck so far with anything. Tried converting it to lightweight in the same way as putting it on Autonomous IOS but errored out.
Cisco 1811 device. Working great with connection from TWTELCOM, trying to add 2nd connection from BRTHOUSE set SLA's and metrics but config still isn't working. The connection won't come up and when I do show ip route ip address it doesn't show a metric so neither connection has a priority and the connection fails. I want brighthouse to have priority as shown with SLA's but if brighthouse fails I want it to go back to twtelcom. [code]
View 1 Replies View RelatedI have a problem converting 2602 from lightweight to autonomous. It will not boot to the autonomous IOS. The procedure below is waht I did.
ap: set IP_ADDR 10.0.0.1
ap: set NETMASK 255.255.255.0
ap: tftp_init
[Code].....
How can I upgrade my 1041N AP to lightweight firmware? I found an upgrade tool which works in only XP and 2000 machines. I do not have these outdated OS so is there another way to upgrade it to lightweight?
View 2 Replies View RelatedHere is what I am attempting to do.
1. I have a 1042N AP configured as a Workgroup-Bridge attaching to a Lightweight Access Point.
2. LWAPP AP is on a 5508 series Controller.
3. I have MAC Authentication configured through an Ciso ACS box running 5.2 code. And that portion is working.
4. I want to lock this WGB down even further with a second layer of security. I am thinking WPA2 -AES.
How to upgrade C3502i to Lightweight? I failed to upgrade using Upgrade tool v3.4. The error message is "AP model is not supported" . how can I upgrade it?
View 9 Replies View RelatedIs there any difference between AIR-SAP2602-x-K9 with lightweight IOS and AIR-CAP2602-x-K9?
View 3 Replies View RelatedDoing the firmware upgrade on a 1041n AP from Autonomous to Lightweight. Downloaded from Cisco, checked MD5 and got a match so went and upgraded. Upgrade went find etc.. and rebooted. When I reboot I get the following error and then rubbish text
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0xc0000000
RQDC, RFDC : 0x80000037, 0x0000018a
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
[code]...
I rolled back to the autonomous OS and all ok and AP operates as normal. When on the lightweight IOS I can get a telnet response but cannot access as it states Password require but not set.
Followed this process to upgrade [URL] and followed this process to restore to Autonomous: [URL] why it's not working.
Update: Just tried another AP same result. Downloaded Lightweight again and same result
Here is the CLI upgrade process
examining image...
Loading c1140-rcvk9w8-tar.124-21a.JA2.tar .from 172.16.4.114 (via BVI1): !
extracting info (273 bytes)
Image info:
Version Suffix: rcvk9w8-
Image Name: c1140-rcvk9w8-mx
[code]....
Is AP 1220B (b-only radio) supported for registration to WLC (7.0.x) with Lightweight software? I've managed to convert the AP to Lightweight mode, but I could not get it to register with WLC 2504 (software version 7.0). Is it possible that this AP is only supported if changing the in-built radio module?
In the compatibility matrix [URL] there is an information that this AP is supported on WLC up to version 7.0.x. On the other hand it is not supported by Autonomous to Lightweight Mode Upgrade Tool [URL] Since these APs does not have pre-installed MIC, it is mandatory for them to create Self-Signed Certificate (SSC). Upgrade tool could do this job (along with adding the created SSC hash to the authorized list on WLC), but it does not support this particular AP/radio. If I do the conversion manually (archive download-sw ...), the AP does not have the SSC needed for communication with WLC. I've tried making the SSC manually (instructions found on this site [URL] while AP is autonomous mode, and then converting it to Lightweight, but the AP still could not register to WLC.
In the debugs (on WLC/AP), I am receiving an error that is described in some Cisco troubleshooting documents as something related to WLC not having an SSC hash in the auth list. Problem is that the AP is not even sending standard CAPWAP messages and there is nothing to be seen in "debug pm pki enable" on WLC...
I have several Lightweight APs (AIR-LAP1242G-A-K9) runing of a single WLC. We keep getting devices, sometimes all devices, losing network signal. The WLC is running a global power setup so all APs have their power set automatically. The setting for power parameters are default. I have noticed when I run a client test the APs run at 11Mbps while the client devices run at 50-54Mbps. The protocol used by both devices is 802.1G. These network drop offs are frequent and I should say may well be an issue with the client devices although there are several different types of devices experiencing this issue. My question is should the TX and RX rates be the same? Is it ok to have this disparity in the TX/Rx values?
View 7 Replies View Relatedis there any issue in buying air-ap1142n-ek9 802.11A/G/N FIXED AUTO AP INT ANT and later on converting it into lightweight under the control of air-ct2504-15k9 2504 WIRELESS CONTROLLER WITH 15 AP LICENSES ?Are there any requirements on the SW of the WLC and the IOS of the AP? The reason of the choice is budget.
View 1 Replies View RelatedThis is one of our first site where we are implementing Cisco wireless, and we bought some external Autonomous AP1262, when we should have bought Lightweight LAP1262 . We can get those replaced, but I am looking into migrating them in order to get them to register with our 5508 controllers.
There do not seem to be a migration tool to download for 1262. Must it be done via the WCS ?So far I have not managed to add these autonomous AP to the controllers. How to know if a migration toll exists for those !
I have a Cisco WLC 5508 managing several 1252s in lightweight mode. There is a portable across campus that has a standalone network but no cabling to tie in to the corporate network. I have another 1252 that is in autonomous mode. Could I essentially configure that as a bridge with the same security and SSID in order to bridge the corporate WLAN? If not, what are my options?
View 4 Replies View RelatedTrying to convert a spare router (Linksys E3200) into a wireless access point to extend my wireless coverage. I thought knew how to do this but having a problem.The problem I am having is that after I finish step 2 the router reboots with the browser trying to access it at the new ip address. But the browser will not connect.I am doing this on a laptop that is disconnected from my network while I am working on the E3200. It is connected by an ethernet cable. I also tried it wireless with the same result.
View 3 Replies View Related