Need basic wireless configuration for a SOHO Cisco 1811W router? I just need the wireless to connect to the base wired LAN - with both WEP and MAC authentication. And - can the MAC auth. parameters be configured via CLI and not have to use either SDM or CP? I can access the router via SDM - but the Wirless Application will not fire up - and CP doesn't work at all.
View 18 RepliesI am attempting to configure DDNS on an 1811W, but my configuration fails. Apparently,it is not connecting to the TZO server, because when I run <show ip ddns update> in telnet, the message "update destination not available, although rh.tzo.com can be pinged. I am attaching a copy of the config file. the ip name-server entries are my IP DNS, and the url/user name/ key entry was provided by TZO support.
View 3 Replies View RelatedWe have a couple of smaller remote locations running cisco 1811W routers (built in switch ports & wireless).Now I have been tasked with determining if the wireless portion can be converted to Lightweight or not; if so what is required.
I am running
WCS 7.0.230.0
WLC 5508 (same code)
I am setting up 1811w router for accessing internet.DHCP is configured on it but it is not providing IP to laptop connected on port fa6. [code]
View 3 Replies View RelatedNeed to confirm purpose of command below
dot11 ssid TEST
vlan 4
authentication open
authentication key-management wpa
guest-mode ?????
Why we need guest-mode command in above config?
I'm having a problem when configuring this cisco router 1921 with an ip base software. Accordingly with the Cisco software adviser this software allows to configure the l2tp Client Initiated Tunneling. But configuring the router the commands are not recognized:
Router(config)#pseudo wire-class L2TP_PSEUDO
^
% Invalid input detected at '^' marker.
Router(config)#interface Virtual-PPP1.
I am working up a configuration template for an install I am doing in a couple weeks and wanted to take a look at the base config of an ASR1002.
View 1 Replies View RelatedMy ASA 5505 base license allows for three VLANs, the third one can only initiate traffic to one other VLAN (as specified by no forward interface vlan <number> on the third VLAN). This doesn't mean it can't "access" the other VLAN, it just can't initiate traffic to it. A lot of people get that wrong.Let's say you've got three VLANs, one is OUTSIDE, two is DMZ, and three is INSIDE. On the second VLAN would I enter the no forward interface as vlan 3, then set the name via the nameif command and everything will work just fine. The DMZ will not be able to initiate traffic to the INSIDE, but will to the outside, and assuming you have your ACLs and NAT set up properly, it will be able to respond to traffic from the INSIDE.
Would that be best practice or would I enter the "no forward" interface as in VLAN 1, thus is being able to respond to traffic from the outside as opposed to the inside.
I had a DMZ set up but since there was an intrusion into my network, I am building it again.
configure the Firewall ASA 5510 in context based configuration in HA Mode with two different subnet....
IP Details are below.....:
interface Ethernet0/0
nameif outside
security-level 0
[Code].....
During high throughput times (nightly, when backup runs) we see packet drops on the network. We think it's the ACE module that drops. We use 2 ACE 20-MOD-K9 with base licenses in a FT configuration in Layer2 Mode.Now I found an interesting statistic on the ACE: [code] How to reset this counter?
View 4 Replies View Related1)For 3650X I found some contradiction in the Q&A about feature set LAN Base vs IP Base:
LAN Base: Can I do static IP routing ?
LAN Base: SVI => is this for intervlan routing ?
2)For 2960, there are 2 flavors (LAN lite and LAN BASE) Q: Can I do static routing on one of these flavors ?
I have a WS-C3750X-12S-S (IP Services) that I THINK I'd like to downgrade to LAN Base so I can stack it with a WS-C3750X-48T-L that is already LAN Base..
View 4 Replies View Relatedcan we upgrade 2960 switch from Lanbase IOS to IPbase
View 4 Replies View RelatedI have an 1811w router and can not figure out how to access the settings of the router. I do not have a console port that I can use to access the settings that way so I want to know how to do it using the SDM. I thought I was following the directions but for some reason when I connect my computer to one of the routers LAN ports no connection is recognized on either the router or the computer. How do I go about connecting to the router and accessing the settings?
View 1 Replies View RelatedOn 1811W Router i have OSPF running and i do not need this static route.ip route 192.168.20.0 255.255.255.0 192.168.20.3,when i try to delete i get error ,1811w#,config t,Enter configuration commands, one per line. End with CNTL/Z.,1811w(config)#no ip route 192.168.20.0 255.255.255.0 192.168.20.3,%No matching route to delete,1811w(config)#.
View 7 Replies View RelatedWireless is working ok on 1811W.Need to know from command output below what values are considered good for power and signal strenghts
1811w#sh dot11 associations all-client
Address : 40fc.894e.c48c Name : NONE
IP Address : 192.168.98.2 Interface : Dot11Radio0
Device : unknown Software Version : NONE
[code].....
Also what is Association ID mean in above output?
I have a Cisco 1811W that after several years in service suddenly stopped allowing any wireless connection to laptops on the domain. It allows hard wired connections and devices that are just using the wireless hot spot like iPads and Iphones but not devices on the domain. These same laptops connect wirelessly without issue at our other facilities which use the same hardware.
Here is the config file of the router in question...
router#show run
Building configuration...
Current configuration : 11776 bytes
[Code].....
I was wondering if it is at all possible to set up a DIR-655 as a wireless base station for any router (specifically a netgear wrg614 v10). I've read that the DIR-655 can be set up as an access point, but with my current situation it's not currently possible.If this is not compatible with this specific netgear router, is there any other solution besides having to purchase a dedicated access point?
View 3 Replies View Relatedi have router WRT45G ver 7 it work but when i want to access in web base utility the router reboot
info:
led power is on stable
led lan is on
led wlan on and the access point work
1.http:\192.168.1.1
2.enter user name and password (admin,admin)
3.hir the page begin to get after a few second the router reboot Page cannot be displayed completelty
i try :
- simple reset
-(30/30/30) reset and i enter in managment mode firmware upgrade
i don't try hardware reset
I would like to use my new EA6500 as the base station and another wireless router with Wireless Repeating Function as a repeater. Is the EA6500 capable of that?? I have not found any documentation on that subject.
View 6 Replies View Relatedi have router WRT45G ver 7 it work but when i want to access in web base utility the router reboot
View 4 Replies View RelatedCisco 1811 device. Working great with connection from TWTELCOM, trying to add 2nd connection from BRTHOUSE set SLA's and metrics but config still isn't working. The connection won't come up and when I do show ip route ip address it doesn't show a metric so neither connection has a priority and the connection fails. I want brighthouse to have priority as shown with SLA's but if brighthouse fails I want it to go back to twtelcom. [code]
View 1 Replies View RelatedI am having a hard time connecting my router into a internet modem since my modem is giving its own private ip address in short the modem is a router in itself. in addition, I cant change the modem's dchp pool its fix with 192.168.1.0 network.
View 3 Replies View RelatedI have some problem to get working ACLs. The main purpose of this ACLs is to control what is going out from vlan to internet. (For example, i want that only my proxy can access to the web.) So, i use Cisco Packet Tracer and test new rules in lab without any problem.
interface Vlan1
ip address x.x.x.x x.x.x.x
ip flow ingress
ip flow egress
ip nat inside
[Code]...
But it doesn't work on my Cisco 1811w and i dont uderstand why and i'm not sure to have sufficient knowledge to aolve my problem by my own.
I am using a 1811W and CCP for configuration. I am trying to assign client names to devices on the LAN so that when a network scanner is used, the client name is displayed. I have attached part of the running config after a binding has been done. My assumption is that the scanner should now show 192.168.1.109 as name <Supermicro>, but the name is blank. Is this configured correctly for what I am trying to acheive?
View 3 Replies View RelatedCisco 1811W router, IOS 15.1(4)M6, DHCP server not working on internal VLAN but configuration looks OK to me. [code]
View 1 Replies View RelatedI am setting up 1811w router for accessing internet. DHCP is configured on it but it is not providing IP to laptop connected on port fa6.
Here is config of router
dot11 ssid internet
vlan 98
authentication open
[Code].....
I have Cisco 2651XM and currently running old IOS c2600-is-mz.123-26.bin (IP PLUS) which I used the NAT protocol. I was wondering can I use IP-BASE on this router and I am not sure if this feature set has NAT protocol.
View 1 Replies View RelatedTrying to configure 1811w for wi fi . Need to use authentication shared keys but current IOS seems does not support ir
Router(config)#int dot11Radio 0
Router(config-if)#ssid manvee1
Router(config-if-ssid)#a?
% Unrecognized command
Router(config-if-ssid)#
(C181X-ADVIPSERVICESK9-M), Version 12.4(24)T8.
Need to know which IOS will support wi fi and authentication command under dot11 radio 0?
Using Cisco 1811W with IOS 15.1(4)M5. FE0 and FE1 are connected to the internet via Billion ADSL2+ modems operating in bridged mode. Both lines are similar so I'll only discuss FE0 from this point on.Local subnet is 192.168.128.0/24 with router on 192.168.128.1 as default gateway. Modem on FE0 has static LAN IP of 192.168.128.2 and when plugged into the switch on the LAN side, the web interface can be accessed at that IP address. Unplug the modem from the switch and plug it into FE0 and it now works as desired providing access from the router to the internet but the web interface is no longer accessable at 192.168.128.2
I tried adding a static route "ip route 192.168.128.2 255.255.255.255 FastEthernet 0" and also "ip route 192.168.128.2 255.255.255.255 Dialer 1" Neither worked and presumably it isn't that straight forward. Possibly NAT or other routing configuration required.Although there isn't much to configure when in bridged mode, I mostly want this setup so I can look at the ADSL connection status and for the modem to write messages to syslog (works when plugged into switch on LAN side), or SNMP access.
I have 2691 Router conencted to Internet and it is doing Nat. This connects to 3550A Switch which has connection to 1811W Router.
I setup VPN between 1811W and 3550A. 3550A has connection to 2691 via ospf.
OSPF is running between 1811w and 3550A.
1811
1811w# sh crypto isakmp sa
IPv4 Crypto ISAKMP SA
[Code].....
First I'm sharing a network via bridging from my dads house. Everything works perfect. I'm using a router at my house with no problems. At his house he as a modem hooked to net gear router and the acer will not connect to internet via wifi. So I bring the thing up to my house and it connects fine via wifi. The acer will connect using a eithernet cable at his house but not wifi.
I was wondering if the acer is getting confused cause his router is hooked to a modem?I've tested and tryed everything under the sun and nothing seems to work.I know theres nothing wrong with the wifi software or hard ware in the acer cause it connects fine And surfs the web via wifi at my house but not at my dads.
If Cisco Router 2921 base load supports NAtting? I am looking to order a Router and want to make sure the new 2900 routers support Natting.
View 2 Replies View Related