D-Link DIR-655 :: Possible To Set Up As Wireless Base Station For Any Router
May 20, 2011
I was wondering if it is at all possible to set up a DIR-655 as a wireless base station for any router (specifically a netgear wrg614 v10). I've read that the DIR-655 can be set up as an access point, but with my current situation it's not currently possible.If this is not compatible with this specific netgear router, is there any other solution besides having to purchase a dedicated access point?
View 3 Replies
ADVERTISEMENT
Oct 20, 2012
I would like to use my new EA6500 as the base station and another wireless router with Wireless Repeating Function as a repeater. Is the EA6500 capable of that?? I have not found any documentation on that subject.
View 6 Replies
View Related
Aug 23, 2012
Can I connect 2 or more wireless repeaters to the same wireless base station signal to extend wireless coverage? I.e. The base station is located in the centre of the building and the signal covers the middle but not the extreme end of the building. I would like to add a repeater on each opposite sides of the signal's reach so it covers the complete building. I can't use LAN cable and the building has different electricity supply to the 3 different part of the building so can't use the mains to carry the signal. Is this possible using wirless repeaters or do I have to use wireless bridge units to connect to the base station and then output with wireless access points attached to the bridge unit to extend the wirless signal?
View 6 Replies
View Related
Dec 6, 2012
I have two computers, one is a Dell Dimension 8300 while the other is a Compaq Presario Desktop. Both use Microsoft Windows XP OS 32 bit and are networked using a Microsoft Wireless G-Base Station MN-700 on the Dell and a Wireless G-Adapter on the Compaq. This arrangement worked quite well for some time and recently they stopped communicating with each other. I reset the base station as described in the manual. When I did the same for the Adapter I could not enter the correct Wireless Security Key. I tried copying the key from the Base to the adapter but to no avail. Do I have to uninstall both units from their respective computers and reinstall from the CD provided?
View 7 Replies
View Related
Mar 19, 2013
-Region : Spain
-Model : TD-VG3631
-Hardware Version : V1
-Firmware Version : 0.6.0 1.0 v0001.0 Build 130108 Rel.54595n
I have a problem with the VoIP feature of this router:I configure the router as a sip station of a asterisk local PBX (192.168.1.254),To this point everything is fine, I can call with a asterisk sip station to a analog phone (sip station 100) that is conected to the FXE port of the TPLINK,The problem occurs when I want to call with the analog phone to a sip station. I have a dial plan with a 0 prefix to call stations using the sip acount:Profile Name Registrar Address Phone Number Status Remove Edit Prueba192.168.1.254100up.And when I call, I can see in the log the INVITE action.
View 1 Replies
View Related
Mar 19, 2013
Region : Spain
Model : TD-VG3631
Hardware Version : V1
Firmware Version : 0.6.0 1.0 v0001.0 Build 130108 Rel.54595n
ISP :
I have a problem with the VoIP feature of this router:I configure the router as a sip station of a asterisk local PBX (192.168.1.254),To this point everything is fine, I can call with a asterisk sip station to a analog phone (sip station 100) that is conected to the FXE port of the TPLINK,The problem occurs when I want to call with the analog phone to a sip station. I have a dial plan with a 0 prefix to call stations using the sip acount:Profile Name Registrar Address Phone Number Status Remove Edit Prueba192.168.1.254100up And when I call, I can see in the log the INVITE action :
32013-03-19 10:16:33OTHERDebugport 1 cx 0x3, evt/reason 3/0 buf (nil)
42013-03-19 10:16:01OTHERDebugport -1 cx 0x3, evt/reason 1/4 buf 0x4761a8
52013-03-19 10:16:01OTHERDebugthe initial INVITE request for [accIndex(0),callIndex(3) dest(<sip:103@192.168.1.254>)] is sen
But I�am sniffing traffic in the PBX and not received the invitation... Obviously the 103 station never recive the call...I think that maybe the INVITE is going out behind the WAN interface.... bug version?
View 1 Replies
View Related
Feb 12, 2013
My buffalo link station 3t was giving me problems due to avg firewall blocking access to my drive. so switched it off to work . now that the drive is working but now when i click to access the drive the back ground on the desktop goes black on windows 7 its a acer laptop and the graphics are blurey.
View 1 Replies
View Related
May 5, 2012
I had a W120N wireless router which received all internet radio stations with no problemsI have just acquired an E3000 and it appears to not pass through 2 particular internet stations that worked fine on the 120N What configuration parameters affect internet radio?Currently, I'm using all the same parameters from the 120N where possible.
View 4 Replies
View Related
Mar 28, 2012
1)For 3650X I found some contradiction in the Q&A about feature set LAN Base vs IP Base:
LAN Base: Can I do static IP routing ?
LAN Base: SVI => is this for intervlan routing ?
2)For 2960, there are 2 flavors (LAN lite and LAN BASE) Q: Can I do static routing on one of these flavors ?
View 2 Replies
View Related
May 6, 2012
I have a WS-C3750X-12S-S (IP Services) that I THINK I'd like to downgrade to LAN Base so I can stack it with a WS-C3750X-48T-L that is already LAN Base..
View 4 Replies
View Related
Nov 14, 2011
can we upgrade 2960 switch from Lanbase IOS to IPbase
View 4 Replies
View Related
Mar 2, 2009
Need basic wireless configuration for a SOHO Cisco 1811W router? I just need the wireless to connect to the base wired LAN - with both WEP and MAC authentication. And - can the MAC auth. parameters be configured via CLI and not have to use either SDM or CP? I can access the router via SDM - but the Wirless Application will not fire up - and CP doesn't work at all.
View 18 Replies
View Related
May 1, 2012
We would like to install a wireless network throughout the station. Currently we have a wired network with 15 PC's and are looking at obtaining tablets for our squads and apparatus. The station is quite large and is divided by the vehicle bays.I'm thinking that we will need multiple access points throughout the station. I am familiar with setting up one wireless router but not with multiple access points.
View 2 Replies
View Related
Sep 22, 2011
i have router WRT45G ver 7 it work but when i want to access in web base utility the router reboot
info:
led power is on stable
led lan is on
led wlan on and the access point work
1.http:\192.168.1.1
2.enter user name and password (admin,admin)
3.hir the page begin to get after a few second the router reboot Page cannot be displayed completelty
i try :
- simple reset
-(30/30/30) reset and i enter in managment mode firmware upgrade
i don't try hardware reset
View 6 Replies
View Related
Sep 22, 2011
i have router WRT45G ver 7 it work but when i want to access in web base utility the router reboot
View 4 Replies
View Related
Nov 10, 2012
Samsung CY-WDCA7UT/ZA USB Central Station Dongle driver?
View 1 Replies
View Related
Oct 29, 2012
We have been having issues with random packet drops and or some sort of radio lockup which happens a few times a day. I have a test AP setup with a few clients only a few feet away and I see this combination of messages. Should I be seeing these clients drop off and then reconnect immediately? Granted these test clients are not passing much data but my assumption is that they would not become deauthenticated because of lack of activity? This setup is using a radius server for authentication. I tested it before with just WPA2 PSK and only had a few disconnected over a number of days, compared with many a day with the Radius.
View 1 Replies
View Related
Oct 9, 2012
We have 5 Cisco Aironet 1100 wireless access points and we are having huge problems in the last few days with them disconnecting some mobile barcode scanners that we have.
We have two Aironet's in the top of the factory which work fine and 3 down the bottom which keep kicking the barcode scanners off. If we use the barcode scanners at the top of the factory they work fine, as soon as we come down to the other 3 WAPs it they keep connecting and disconnecting.
We get the following error in the Event log on the access points.Disassociated because sending station is leaving (or has left) BSS On the barcode scanners. [code]
View 1 Replies
View Related
Mar 9, 2012
I am using a wireless connection via router to access internet at home. When my Dell Latitude E6510 Laptop is not on the Dell Docking Station and I'm using as just standalone I can access my wireless connection easily, no problem at all.However, when I attached my laptop to my Dell Docking Station, I can not access my wireless connection. The wireless connection is found, but when I click connect to network, I get "Windows cannot found network". When I remove the laptop from the docking station, I find the wireless connection and connect perfectly and it works normal.I am using Windows 7. I can connect to internet with straight wire going to docking station easily, but no wireless connection found when laptop is on the docking station. I work from home and use the docking station for two monitors for doing my job. I have struggle with this problem for two weeks now. I don't see anything on the docking station that's preventing me from access my wireless connection.
View 1 Replies
View Related
Apr 13, 2012
First I'm sharing a network via bridging from my dads house. Everything works perfect. I'm using a router at my house with no problems. At his house he as a modem hooked to net gear router and the acer will not connect to internet via wifi. So I bring the thing up to my house and it connects fine via wifi. The acer will connect using a eithernet cable at his house but not wifi.
I was wondering if the acer is getting confused cause his router is hooked to a modem?I've tested and tryed everything under the sun and nothing seems to work.I know theres nothing wrong with the wifi software or hard ware in the acer cause it connects fine And surfs the web via wifi at my house but not at my dads.
View 14 Replies
View Related
Apr 17, 2012
I have Cisco 2651XM and currently running old IOS c2600-is-mz.123-26.bin (IP PLUS) which I used the NAT protocol. I was wondering can I use IP-BASE on this router and I am not sure if this feature set has NAT protocol.
View 1 Replies
View Related
Aug 19, 2012
I'm using an HP Elitebook 6930p with Windows XP and an HP EN488UT docking station. When I use the computer by itself the Network Connections shows "Local Area Connection 3 Connected Intel 83567LM Gigabit Network Connection" and I can connect to the internet. When I am in the docking station, I can also see this connection, as long as my notebok is open when I start up. However, if i start the computer with the lid closed (I just want to use the external monitor, not the notebook monitor) that network connection does not appear and I cannot connect to the intenet.
[code]....
View 5 Replies
View Related
Nov 13, 2012
If Cisco Router 2921 base load supports NAtting? I am looking to order a Router and want to make sure the new 2900 routers support Natting.
View 2 Replies
View Related
Jun 7, 2011
I have a LAN with multiple VLANs connected through Catalyst 3750 with IP Base image. In IP Base the router only supports PIM stub multicast (no PIM multicast routing),But I have an ASA connected to the internal router and to the internet router.Asa supports PIM multicast routing and can act as PIM RP. With this configuration, is there a way to configure an internal multicast network? That is a multicast server in one internal vlan (VLAN 1) and multicast clients in VLAN 2. Both VLANs connected to the C3750 router.
View 3 Replies
View Related
Feb 12, 2013
We have purchased a number of 2911 routers.We got Base & security license as we wanted to enable encryption. However we probably wont use the security.We are replacing 2811 routers.Unfortunately the 2811 routers have FXS ports with 2 - 4 POTS handsets - I completely forgot about these ports when I was ordering.Now I have VIC3-FXS cards which are ok in the 2911 but unfortunately I cant get them to work.I am missing PVDMs (well adapters anyway), and even if I got them the router wont take any commands relating to voice due to the license.Is is possible to 'rehost' the security and turn it into a UC ?I am new to these 2911 and Licensing.
View 1 Replies
View Related
Mar 10, 2011
what is a diskless station in networking
View 1 Replies
View Related
Oct 16, 2012
if the network i'm planning on will even work so i drew a picture on my project (attached). All cables will be gigabit compatible as will be the switches. The reason i will have 2 switches is because they won't be in the same building. The uppermost switch will be physically next to the router to enable me to have gigabit connection between the DiskStation and the PCs/HTPC without having to change my router (in fact can't change it due to special firmware for my internet TV).
View 4 Replies
View Related
Feb 28, 2012
I have the Air Station WHR-G300N. I just moved here from CA, I was on Verizon and now trying to use it on my girlfriend Cox system I can't get it to operate correctly.
Her PC system stopped having internet connection after about 2 weeks(running on the router) and going with Cox's reboot procedure of eliminating the router it can back up and seems to work fine as soon as I hook it back to the modem it stops.
I have unplugged all cables waited 30 seconds on both systems a couple of times. The lights are on the modem and the router.
View 1 Replies
View Related
May 18, 2012
I am trying to install ACS 5.0 on workstation, however once the install finsihes it reboots and I enter the Linux bash command line rather than the Cisco CLI.
Note - this is now fixed. I followed the steps here to install ACS 5.0 on VMware Workstation 7: url...
View 2 Replies
View Related
Mar 28, 2013
I am blocked with the below doubt for my issue resolution. When a ethernet frame for eg:ARP Packet of minimum length (64 bytes) is received at the end station, will the L2 layer remove both FCS and extra padding bytes(18 padding bytes for ARP)? Or removal of the padding bytes is dependent on the implementation?
View 2 Replies
View Related
Dec 7, 2012
i have 10 stations, and i think one of them generated allot of traffic.maybe a virus sending spam.is there a command that can show my which station consume bandwidth?
View 3 Replies
View Related
Jun 24, 2012
In ACS 5.3 radius authentication report I want to show the called-station-id attribute. (this was appearning on failed and passed auth in ACS 4.2). The value of called-station-id appears in the details. However, I want it to appear as a column with the report.
View 2 Replies
View Related
Oct 26, 2011
I have a Latitude D820, Windows XP, SP3. At my office I have a regular docking station but at home I have a D/Dock docking station. When I dock the 820 at home the Broadcomm network card works flawlessly. When I dock it in the office, it will occasionally work but most of the time the link light and data light on the docking station are on solidly and XP reports that the cable is unplugged. I have tried two different docking stations with identical results and also tested the cable by plugging it into the docking station that holds a D810. With the D810 it worked normally.
View 1 Replies
View Related
