I had a W120N wireless router which received all internet radio stations with no problemsI have just acquired an E3000 and it appears to not pass through 2 particular internet stations that worked fine on the 120N What configuration parameters affect internet radio?Currently, I'm using all the same parameters from the 120N where possible.
View 4 RepliesI have recently discovered that I can stream audio from my WRT54G V2 via a wireless extender.I can not play internet radio, or stram Rhapsody via the extender.The extender will not stream audio.This is actually quite normal behavior of a Range Extender. Range Extenders work off of the idea of pulling a signal from the Base Station and then repeating the signal frequently, this generally causes rebuffering issues with most wireless devices within a network.I believe I need a wireless extender that does not repeat the signal, more of a wireless access point.
View 2 Replies View Relatedjust bought an e3000 and want to use it with wireless internet- usb modem. when setting up it wouldnt go any further than the 'searching for connection' page as it couldnt detect a connection in the 'internet' lan (wan?) port.can i set it up to accept the wireless usb modem?
View 6 Replies View Relatedshows connection to cable modem, shows IP lease, able to renew and release lease. shows all DCHP clients, but does not allow internet to get through. tried cloning old routers MAC, no dice.
View 6 Replies View RelatedThe Internet LED does not light up when I have access to the Internet like now. I think I remember this lighting up in the past and find it strange that an LED light would burn out so early
View 5 Replies View RelatedI just purchased an E3000 to replace my WRT54G.I set up the E3000 through a wired connection from my Comcast modem to my desktop (running Windows 7).Through Cisco Connect, I was unable to connect to the internet. The desktop connects to the E3000 but the E3000 does not connect to the modem. I've tried to reset the E3000 and power down both the E3000 and the modem yet I still cannot connect.I swapped my WRT54G back into place and my connection is fine while I figure this out.
View 4 Replies View RelatedI have been running some test to see what I can do for speed to the interenet and NAS drive.I have a NIC card (1394) and the max connection I get is 400 Mbps. The card is suppose to be 10/100/1000 card and E3000 is the same... so why can't I connect at 1000?Max transfer I get to my NAS is 64-80 Mbps. Is there any way I can get this to be faster? I have a 1TB western digital drive attached.If I went with a NAS system like a Synology BYOD system could I get faster speeds for transfers if the NIC on the system was a 10/100/1000?`
View 5 Replies View Relatedi was having issues with one of my devices after a power outage. all my other devices worked (laptops, xbox, iphones, etc)i thought doing a reset on the router would get the odd device working again but all it did was mess up my internet. i don't have the key or cd any longer from when i set it up.
View 9 Replies View RelatedI have a cable modem with an E3000 router, wired to my desktop. Internet connection is fine for my desktop, wired to Xbox, wifi for Iphone, Ipod, but no connectivity to my laptop wirelessly. I have run the repair automatically on my laptop (Windows 7) and get 2 different messages when trying over and over to use this tool. 1. Network Configuration Problem 2. Problem with wireless adapter or access point. I get a "fail" when trying this:
1. If your client device has a Wi-Fi Protected Setup™ button,click or press that button and then click the button on the right. or when putting in the router's pin number.
I just got optical fiber installed in my place which gives me great download speeds. Now my ISP has a monthly download limit of 120GB, after that I gotta pay overages.Now my setup is like this: Fiber modem (1 port) -> Linksys E3000 router (4 ports + wifi).All my gear is hooked up to the Linksys router (xbox, ps3, media center, office pc & 2 laptops).I would like to keep track of the total "internet" bandwidth use of all devices, but exclude the normal network traffic, as that of course I don't pay for.Is there something that I can install on the Linksys router that can keep track of that kinda of information? router (4 ports + wifi).
View 6 Replies View RelatedI have a E3000 router and I want to slow the upload and download speed to my Xbox is there any way to do this thru the router settings. I have internet that is about 20-30mbps down and 2-3mbps up I want to slow it to about 5-6mbps down and 1-2 mbps up.
View 2 Replies View RelatedI came home yesterday and my Internet was really slow. I later found out that it was due to my Linksys E3000 because if I bypass my E3000 and go directly to my cable modem, it work just fine.I tried reconfigure, update firmware, factory reset and none of these has worked.
View 8 Replies View RelatedInternet policy access on my Linksys E3000. I am trying to block facebook.com to a particular ip address in my office. This what I did. Logged in to control panel clicked on access restriction. Clicked on add. Gave it a name. Clicked the applies to drop down box and selected by ip address. Unchecked the block all internet access. Typed facebook down in the window below. Saved.Not blocking access.
View 9 Replies View RelatedI can now access my router config pages when connected to my ATT router. However, I cannot seem to access the Internet when connected to my e3000; I just time out. I also have difficulties just connecting to my e300 for some reason. I have been connected a couple of times where i could access the Internet but it was only for a few minutes and it was very slow.I can't seem to put the router in the DMZ because the ATT router will only DMZ a DHCP-enabled device and the e3000 has a static IP (192.168.1.253). I have tried running the PING and Traceroute diagnostics and both just come back with Unknown Host no matter what URL i enter. The status page also appears as if the e3000 is not properly talking to the ATT router. Under the Internet Connection area it shows Connection Type: Automatic Configuration - DHCP then 0s for IP address, subnet, and gateway. the DNS entries are empty and the MTU shows 1500 and the DHCP Lease Time is also empty. i am all ears and willing to try whatever. But i just want to be able to connect to my e3000 so i can utilize the wireless n internally and connect a 2TB external drive to share. But I also want to be able to get out to the Internet when i am connected to the device.
View 6 Replies View RelatedI purchased a refurbed? router on the internet, not supported any longer by Cisco Chat. I have a wireless internet: WiMax thru Clear wireless. I have a Linksys voip box coming off it for my phones. I installed the disk that came with the router, followed the directions, and got a message that Internet could not be found. Went to the live chat and followed some advice that did not work, conflict with voip? bypassed the voip and ran a cable from the wireless modem to my E3000.
View 3 Replies View RelatedI just bought a new E3000 router less than 2 weeks ago. I spent hours with my tech guy setting up the router so that I was getting excellent internet speed and the connection between my computer and my nas was maximized. In the process of setting up the router my laptop (Windows 7) and the basement laptop (Vista) were set up to access the router. Both work perfectly.These are now the only two devices in the house that can get internet access.The other devices that should connect are:
-2 Laptops (both Vista)
-1 iPhone 4
-2 iPhone 3gs
-1 Printer
I can't get them to connect. I spent an hour with a guy at Cisco tonight who just couldn't seem to get past the idea that it was not the laptop that was the problem.
I have had numerous issues with my E3000 since I got about two months ago and they have all been resolved with the exception of this new one that popped up today.
My Samsung Blu-ray player is connected firectly via ethernet cable to the router. When it's on, I lose all conenctivity to the router with my wireless devices including three PC's, a PS3, two iPhones, one iPad, one Samsung Smart TV, one XBOX 360 and an Onkyo Receiver. When I say that I lose connectivity, I don't mean that I lose access to the Internet. My PC's see the network but cannot connect to it, the same goes for the Apple devices. The moment I shut off the Samsung BD player it kicks right back on and works normally. Until today, this never occurred.
I contacted Tech Support and they had never heard of this happening before. They suggested that I change the ethernet cable which I did while the unit was on and it worked until I turned the BD player off and turned it back on again. I also tried switching ports to no avail. Alos all of the software is up to date on both the router and the BD player.
I would like to use my new EA6500 as the base station and another wireless router with Wireless Repeating Function as a repeater. Is the EA6500 capable of that?? I have not found any documentation on that subject.
View 6 Replies View RelatedMy Cisco E3000 has slowed it's Ethernet speed so slow that it times out when going to Facebook, YouTube or any site that is complex. It worked fine until one day it just gave up. It's connected to DSL Modem with Ethernet To a Apple Mac G5 power PC There are two other older macs connected via Ethernet, same problem. When I took the router out of the chain, and connected G5 directly to modem, normal internet speed. My firmware is up to date. Both wireless bands work great. When I look at Cisco Connect, everything looks normal. factory settings.
View 7 Replies View RelatedWoke up this morning to the friendly 'No Internet access' message in the system tray. Thought it was the laptop but it wound up being the router (I guess).I can connect directly to internet via the cable modem (Comcast) but can't get a connection through the router.There are no IP addresses listed on the router admin page.Renew IP doesn't work.Everything was ok last night. I've had the router for a year or so and except for having to reset it every week or 2 for WiFi connection issues,it's worked pretty well.I soft-reset the router but then couldn't connect to 192.168.1.1.Hard-reset and still can't connect to 192.168.1.1.I do see connection lights. Just can't get to it.
View 9 Replies View RelatedMy E3000 has been working fine with 1.0.04 build 6 FW. Recently some devices (kindle, iPad) can't connect to internet while connected to E3000 via WiFi network. Had a look my E3000 router IP is 192.168.0.1 but those problematic devices has IP 192.168.1.XXX allocated by DHCP not sure why. Currently I manually set up static IP 192.168.0.XXX for those devices.
View 1 Replies View RelatedWe have the E3000 Router and the guest internet access DOES NOT work. We occasionally repair other people's PC's and I seriously do not want to allow access to our home network. Recently, we are trying to access through guest, on a Win 7 Dell Notebook. It takes the passcode but no internet connection.
View 1 Replies View RelatedConnecting The Internet by Ethernet Lan-cable (without a router), ping to Yandex.ru is 4 ms. If we connect by router ping is 27 ms. If we ping by web-interface it is 4 ms. Connecting by Wi-Fi it is 27 ms.I' ve substituted the cable connected router and computer. So my questions are: why ping is rising when I connect to the Internet by router?
View 1 Replies View RelatedMy main Internet connection is a frontier modem /router It is on the main level of the house. In the basement I am trying to set up the cisco E3000 through an Ethernet cable.
View 4 Replies View RelatedI have had no problems with my WRt610N fo 2 years. Yesterday a problem occured and today again. Namely, I opened my laptop (the lid) and suddenly it could not see my network (SSID) among the rest of the neighbouring ones. The WiFi indicator in the tray showed the yellow "!". Since I have another (secondary) router wired to the primary (WRT610N) I tried and succeeded to connect to it (same SSID, but type "g").
Today the same situation. This is the straneg thing - if I 1st connect to the "g" router after a while the WIn7 reports my SSID being of type "gn" meaning it now sees the primary WRT610N. If I switch off the secondary the netowork is maintained by the primary router showing "n". It seems like my laptop cannot see my router (but can see all other networks) until it 1sr connects to the secondary, and afterwards it sees the primary router and can stay with it.
What Radio Channels are available for selection when operating the EA4500 in Wireless-N (5 GHz) mode only? I need to find a router that can be specifically set on channel 120 in the UK
View 8 Replies View RelatedI've tried every combination with two different Squeezebox Radios to connect via WiFi to my E4200 with no luck. I have other Squeezebox devices that work fine, but the Radio just won't go.
View 4 Replies View RelatedThere is no "blinking light" indication on my E3000 at the Internet (Yellow label) and Ethernet port no 4. I tried plugging in 2 cables at all of the ports. I got the blinking indication at Port 1 through 3. The same cable's have no response at Port 4 and Internet port. As a result my I am not able to connect to the internet.
View 2 Replies View RelatedI previously asked if I should be concerned that the Internet light on my Linksys E3000 router doesn't light up when I have Internet access. Well recently I had to do a reset and I noticed that during the reset it does in fact light up, but it doesn't come on when the router is done with the reset!
View 1 Replies View RelatedI am using a wireless connection via router to access internet at home. When my Dell Latitude E6510 Laptop is not on the Dell Docking Station and I'm using as just standalone I can access my wireless connection easily, no problem at all.However, when I attached my laptop to my Dell Docking Station, I can not access my wireless connection. The wireless connection is found, but when I click connect to network, I get "Windows cannot found network". When I remove the laptop from the docking station, I find the wireless connection and connect perfectly and it works normal.I am using Windows 7. I can connect to internet with straight wire going to docking station easily, but no wireless connection found when laptop is on the docking station. I work from home and use the docking station for two monitors for doing my job. I have struggle with this problem for two weeks now. I don't see anything on the docking station that's preventing me from access my wireless connection.
View 1 Replies View Relatedbest wireless internet network adapter was? I have a Cisco/Linksys e3000 Wireless simultaneous Dual band router, so 2.4 GHz and 5 GHz are up for debate. My MoBo is the ASUS P8Z68-V PRO/GEN3, so it has built in bluetooth, which tends to affect my internet speed when used on the 2.4GHz bandwidth
View 1 Replies View RelatedI was wondering if it is at all possible to set up a DIR-655 as a wireless base station for any router (specifically a netgear wrg614 v10). I've read that the DIR-655 can be set up as an access point, but with my current situation it's not currently possible.If this is not compatible with this specific netgear router, is there any other solution besides having to purchase a dedicated access point?
View 3 Replies View Relatedinternet works fine with Belkin router replaced with Linksys E3000 and neither wired or wireless internet will connect to any web addressModem is ATT U Verse 2Wire with wireless feature disabled
View 1 Replies View Related