The Internet LED does not light up when I have access to the Internet like now. I think I remember this lighting up in the past and find it strange that an LED light would burn out so early
View 5 RepliesI previously asked if I should be concerned that the Internet light on my Linksys E3000 router doesn't light up when I have Internet access. Well recently I had to do a reset and I noticed that during the reset it does in fact light up, but it doesn't come on when the router is done with the reset!
View 1 Replies View RelatedI recently switched my router from an older Linksys WRT 54GS to an E3000. The WRT 54GS was working perfectly fine, but I needed to upgrade to a 802.11n router to use with some of my devices at home. I unplugged all the cables from the WRT54GS, and connected all the cables into the E3000 - in the exact same sockets and order they were on the old router. When powering on, all the lights eventually turned on (Power, Internet and Ports 1 to 4), except the wifi is still off. I tried running the installation CD, but it says it cannot find the network. I tried a reset (back button) as well as 30-30-30 reset, but no matter what I do, the wifi indicator still doesn't turn on. When switching back to the old router, it has no problem broadcasting a wifi signal again. Is there anything else I should try, either on my PC settings or the E3000 router itself?
View 5 Replies View RelatedMy house was in the middle of a lightning storm today while I was out and I came back to no internet. Figgured it was just the phone lines down, but connectiong directly to the modem I found I had connectivity. The WRT54GL (flashed with DD-WRT) doesn't pick up the WAN IP, I've checked with multiple ethernet cables, 2 different modems (all of which work fine with our computers, providing connectivity) and am currently using the router that the WRT54GL displaced ~8 years ago. I'm assuming it's just dead, but wanted a second opinion... kinda odd that a surge would have come through the phone line, through a DSL modem and killed the WAN port of the router instead of taking out the modem?
View 2 Replies View RelatedI just bought linksys EA2700 to replace my U.S Robotics .. but when i try to connect it like the old router , the internet lights won't turn on, is it because i have to use a modem then use ethernet cable ? can't i just use ADSL cable directly to the router like robotics router ? when i try to configure it manually , i change the internet type to PPoE protocol but i can't find VCI/VPI so where are they ?
View 1 Replies View RelatedI have a Linksys WRT54GS vers 7.2 Router on an iMac OS X Leopard. The other day I was in the middle of downloading an upgrade for the router when Firefox gave me this message: "Firefox can't find the server". I was no longer able to access the internet, and the router's green power light was left flashing. It flashed for over 24 hours. I tried unplugging the router and shutting down the computer, then plugging in the router and turning on the computer. (I don't have a modem.) The light was still flashing. I tried pressing the logo button for 5 seconds. Still flashing. Tried pressing the reset button in the back. Still flashing. 'I can't get on the internet or into the router. Linksys live chat gave me a link to "Upgrading the router’s firmware using the TFTP utility", which involves a download, but I can't download anything because I can't access the internet.
View 8 Replies View RelatedWRT400N worked great for 18 months.
Last week the Verizon-supplied DSL modem went bad (wasn't receiving data) and was replaced.
Now I can get Internet direct out of modem, and when I connect it to router the router's Internet light is on, but it seems to stop there. Devices connected to router via Ethernet or wifi don't get Internet.
I'm able to get to the router's admin console via Ethernet and wifi, but no Internet.
So I just got this new WRT160Nv2 router. I have (1) wired computer and then my laptop running wireless to it. For the first couple days I had some issues getting consistant internet but after reading some stuff on here I downgraded to the version 8 hardware and it worked GREAT for about 3 days. Now my power light won't stop flashing and I have NO internet connection at all through the router. I have tried to reset the router by holding down the button and also unpluging it but still nothing.
View 9 Replies View Relatedjust bought an e3000 and want to use it with wireless internet- usb modem. when setting up it wouldnt go any further than the 'searching for connection' page as it couldnt detect a connection in the 'internet' lan (wan?) port.can i set it up to accept the wireless usb modem?
View 6 Replies View Relatedshows connection to cable modem, shows IP lease, able to renew and release lease. shows all DCHP clients, but does not allow internet to get through. tried cloning old routers MAC, no dice.
View 6 Replies View RelatedI just purchased an E3000 to replace my WRT54G.I set up the E3000 through a wired connection from my Comcast modem to my desktop (running Windows 7).Through Cisco Connect, I was unable to connect to the internet. The desktop connects to the E3000 but the E3000 does not connect to the modem. I've tried to reset the E3000 and power down both the E3000 and the modem yet I still cannot connect.I swapped my WRT54G back into place and my connection is fine while I figure this out.
View 4 Replies View RelatedI have been running some test to see what I can do for speed to the interenet and NAS drive.I have a NIC card (1394) and the max connection I get is 400 Mbps. The card is suppose to be 10/100/1000 card and E3000 is the same... so why can't I connect at 1000?Max transfer I get to my NAS is 64-80 Mbps. Is there any way I can get this to be faster? I have a 1TB western digital drive attached.If I went with a NAS system like a Synology BYOD system could I get faster speeds for transfers if the NIC on the system was a 10/100/1000?`
View 5 Replies View Relatedi was having issues with one of my devices after a power outage. all my other devices worked (laptops, xbox, iphones, etc)i thought doing a reset on the router would get the odd device working again but all it did was mess up my internet. i don't have the key or cd any longer from when i set it up.
View 9 Replies View RelatedI have a cable modem with an E3000 router, wired to my desktop. Internet connection is fine for my desktop, wired to Xbox, wifi for Iphone, Ipod, but no connectivity to my laptop wirelessly. I have run the repair automatically on my laptop (Windows 7) and get 2 different messages when trying over and over to use this tool. 1. Network Configuration Problem 2. Problem with wireless adapter or access point. I get a "fail" when trying this:
1. If your client device has a Wi-Fi Protected Setup™ button,click or press that button and then click the button on the right. or when putting in the router's pin number.
I just got optical fiber installed in my place which gives me great download speeds. Now my ISP has a monthly download limit of 120GB, after that I gotta pay overages.Now my setup is like this: Fiber modem (1 port) -> Linksys E3000 router (4 ports + wifi).All my gear is hooked up to the Linksys router (xbox, ps3, media center, office pc & 2 laptops).I would like to keep track of the total "internet" bandwidth use of all devices, but exclude the normal network traffic, as that of course I don't pay for.Is there something that I can install on the Linksys router that can keep track of that kinda of information? router (4 ports + wifi).
View 6 Replies View RelatedI have a E3000 router and I want to slow the upload and download speed to my Xbox is there any way to do this thru the router settings. I have internet that is about 20-30mbps down and 2-3mbps up I want to slow it to about 5-6mbps down and 1-2 mbps up.
View 2 Replies View RelatedI came home yesterday and my Internet was really slow. I later found out that it was due to my Linksys E3000 because if I bypass my E3000 and go directly to my cable modem, it work just fine.I tried reconfigure, update firmware, factory reset and none of these has worked.
View 8 Replies View RelatedInternet policy access on my Linksys E3000. I am trying to block facebook.com to a particular ip address in my office. This what I did. Logged in to control panel clicked on access restriction. Clicked on add. Gave it a name. Clicked the applies to drop down box and selected by ip address. Unchecked the block all internet access. Typed facebook down in the window below. Saved.Not blocking access.
View 9 Replies View RelatedI had a W120N wireless router which received all internet radio stations with no problemsI have just acquired an E3000 and it appears to not pass through 2 particular internet stations that worked fine on the 120N What configuration parameters affect internet radio?Currently, I'm using all the same parameters from the 120N where possible.
View 4 Replies View RelatedI can now access my router config pages when connected to my ATT router. However, I cannot seem to access the Internet when connected to my e3000; I just time out. I also have difficulties just connecting to my e300 for some reason. I have been connected a couple of times where i could access the Internet but it was only for a few minutes and it was very slow.I can't seem to put the router in the DMZ because the ATT router will only DMZ a DHCP-enabled device and the e3000 has a static IP (192.168.1.253). I have tried running the PING and Traceroute diagnostics and both just come back with Unknown Host no matter what URL i enter. The status page also appears as if the e3000 is not properly talking to the ATT router. Under the Internet Connection area it shows Connection Type: Automatic Configuration - DHCP then 0s for IP address, subnet, and gateway. the DNS entries are empty and the MTU shows 1500 and the DHCP Lease Time is also empty. i am all ears and willing to try whatever. But i just want to be able to connect to my e3000 so i can utilize the wireless n internally and connect a 2TB external drive to share. But I also want to be able to get out to the Internet when i am connected to the device.
View 6 Replies View RelatedI purchased a refurbed? router on the internet, not supported any longer by Cisco Chat. I have a wireless internet: WiMax thru Clear wireless. I have a Linksys voip box coming off it for my phones. I installed the disk that came with the router, followed the directions, and got a message that Internet could not be found. Went to the live chat and followed some advice that did not work, conflict with voip? bypassed the voip and ran a cable from the wireless modem to my E3000.
View 3 Replies View RelatedI just bought a new E3000 router less than 2 weeks ago. I spent hours with my tech guy setting up the router so that I was getting excellent internet speed and the connection between my computer and my nas was maximized. In the process of setting up the router my laptop (Windows 7) and the basement laptop (Vista) were set up to access the router. Both work perfectly.These are now the only two devices in the house that can get internet access.The other devices that should connect are:
-2 Laptops (both Vista)
-1 iPhone 4
-2 iPhone 3gs
-1 Printer
I can't get them to connect. I spent an hour with a guy at Cisco tonight who just couldn't seem to get past the idea that it was not the laptop that was the problem.
I have had numerous issues with my E3000 since I got about two months ago and they have all been resolved with the exception of this new one that popped up today.
My Samsung Blu-ray player is connected firectly via ethernet cable to the router. When it's on, I lose all conenctivity to the router with my wireless devices including three PC's, a PS3, two iPhones, one iPad, one Samsung Smart TV, one XBOX 360 and an Onkyo Receiver. When I say that I lose connectivity, I don't mean that I lose access to the Internet. My PC's see the network but cannot connect to it, the same goes for the Apple devices. The moment I shut off the Samsung BD player it kicks right back on and works normally. Until today, this never occurred.
I contacted Tech Support and they had never heard of this happening before. They suggested that I change the ethernet cable which I did while the unit was on and it worked until I turned the BD player off and turned it back on again. I also tried switching ports to no avail. Alos all of the software is up to date on both the router and the BD player.
My Cisco E3000 has slowed it's Ethernet speed so slow that it times out when going to Facebook, YouTube or any site that is complex. It worked fine until one day it just gave up. It's connected to DSL Modem with Ethernet To a Apple Mac G5 power PC There are two other older macs connected via Ethernet, same problem. When I took the router out of the chain, and connected G5 directly to modem, normal internet speed. My firmware is up to date. Both wireless bands work great. When I look at Cisco Connect, everything looks normal. factory settings.
View 7 Replies View RelatedWoke up this morning to the friendly 'No Internet access' message in the system tray. Thought it was the laptop but it wound up being the router (I guess).I can connect directly to internet via the cable modem (Comcast) but can't get a connection through the router.There are no IP addresses listed on the router admin page.Renew IP doesn't work.Everything was ok last night. I've had the router for a year or so and except for having to reset it every week or 2 for WiFi connection issues,it's worked pretty well.I soft-reset the router but then couldn't connect to 192.168.1.1.Hard-reset and still can't connect to 192.168.1.1.I do see connection lights. Just can't get to it.
View 9 Replies View RelatedMy E3000 has been working fine with 1.0.04 build 6 FW. Recently some devices (kindle, iPad) can't connect to internet while connected to E3000 via WiFi network. Had a look my E3000 router IP is 192.168.0.1 but those problematic devices has IP 192.168.1.XXX allocated by DHCP not sure why. Currently I manually set up static IP 192.168.0.XXX for those devices.
View 1 Replies View RelatedWe have the E3000 Router and the guest internet access DOES NOT work. We occasionally repair other people's PC's and I seriously do not want to allow access to our home network. Recently, we are trying to access through guest, on a Win 7 Dell Notebook. It takes the passcode but no internet connection.
View 1 Replies View RelatedConnecting The Internet by Ethernet Lan-cable (without a router), ping to Yandex.ru is 4 ms. If we connect by router ping is 27 ms. If we ping by web-interface it is 4 ms. Connecting by Wi-Fi it is 27 ms.I' ve substituted the cable connected router and computer. So my questions are: why ping is rising when I connect to the Internet by router?
View 1 Replies View RelatedMy main Internet connection is a frontier modem /router It is on the main level of the house. In the basement I am trying to set up the cisco E3000 through an Ethernet cable.
View 4 Replies View RelatedThere is no "blinking light" indication on my E3000 at the Internet (Yellow label) and Ethernet port no 4. I tried plugging in 2 cables at all of the ports. I got the blinking indication at Port 1 through 3. The same cable's have no response at Port 4 and Internet port. As a result my I am not able to connect to the internet.
View 2 Replies View RelatedI have a netgear MR814 router that is not connecting to the internet. A few days ago my wireless was SO slow that I disconnected and did a powercycle (which usually works when wireless drops off now and then) but then it did not connect to the modem anymore. The ports 1, 4, wireless, and power lights are on but the internet light is off. I know it's not a modem problem because I can hardwire the modem to my laptop and get on internet. I've tried a few things suggested on this forum and elsewhere (maybe I shouldn't have messed with it?) but nothing has worked to resolve the problem. When I am connected to the router I cannot access the routerlogin and the ipconfig/release/renew shows that wireless lan media is disconnected.
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 7 Home Premium, Service Pack 1, 64 bit
Processor: Intel(R) Core(TM) i3 CPU M 370 @ 2.40GHz, Intel64 Family 6 Model 37 Stepping 5
Processor Count: 4
RAM: 3893 Mb
Graphics Card: Intel(R) HD Graphics, 1722 Mb
Hard Drives: C: Total - 458067 MB, Free - 369650 MB; D: Total - 14607 MB, Free - 1626 MB; E: Total - 4055 MB, Free - 1103 MB;
Motherboard: Hewlett-Packard, 1693
Antivirus: avast! Antivirus, Updated and Enabled
best wireless internet network adapter was? I have a Cisco/Linksys e3000 Wireless simultaneous Dual band router, so 2.4 GHz and 5 GHz are up for debate. My MoBo is the ASUS P8Z68-V PRO/GEN3, so it has built in bluetooth, which tends to affect my internet speed when used on the 2.4GHz bandwidth
View 1 Replies View RelatedAfter a recent lighting strick close by I can not connect to the internet through my router. Stright from the modem works fine. The port light on the router does not come on. I rebooted modem, router and computer with no luck. It's like I've lost my network adapters and I don't know how to get them back. I tryed another E2000 and it's the same way.
View 1 Replies View Related