My E3000 has been working fine with 1.0.04 build 6 FW. Recently some devices (kindle, iPad) can't connect to internet while connected to E3000 via WiFi network. Had a look my E3000 router IP is 192.168.0.1 but those problematic devices has IP 192.168.1.XXX allocated by DHCP not sure why. Currently I manually set up static IP 192.168.0.XXX for those devices.
View 1 RepliesI've got the E3000 set up and working. What I'd like to do now is monitor all the devices' connectivity to it. The bandwidth it consumes and stuff. Is there a way to do that on my router?
View 6 Replies View RelatedI have Comcast cable internet routed through a linksys E3000 router. My desktop is connected to my router via ethernet and my various other devices including my laptop are wifi connected. It seems almost at random that my desktop will lose its connection.Windows will show me as still being connected and my network connection will show a normal status until I atttempt to repair it then it will change to limited or no connectivity. Through all of this, my other devices all still have a wifi signal (I don't use more than 1 or 2 at the same time). I can reconnect to the internet by unplugging my ethernet cable then reuplugging it back in and my connection will start working again. I've also had several blue screens, and when I checked the dmp files it revealed my network card driver as the culprit, yet I have reinstalled and even clean installed the microsoft signed driver. I have also attempted to reboot both my modem and router to no avail.
Microsoft XP
Marvell Yukon ethernet adapter on a biostar mobo
C:Documents and SettingsMain>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : sn1
Primary Dns Suffix . . . . . . . :
[code]...
How can I get a E3000 or E4200 to manage more than 5 devices? Come on Cisco, lets get real. EVERYONE has more than 5 devices to manage. The average family of 4 has 3 or 4 computers, 4 smart phones and at least a couple of tablets and maybe some TV or game consoles. Setting access control policies is a must for anyone who is a parent.
Any good router that has a reasonable set of access control features? I've always loved Cisco up to this point, but I'm frustrated by this significant limitation.
I have 3 computers in total: 2 desktops and 1 laptop.
1. My primary PC is connected physically to my router.
2. My (downstairs) laptop is connected to the wireless.
3. My other PC connects to the wireless network via USB wireless adapter.
I was having issues getting #3 connected to the wireless network. I used the Wi-Fi Protected Setup™ PIN number provided to me by the Linksys Wireless Manager to no avail. The E3000 router and #3 could never find each other.After calling support, it turns out that more often than not, "other" wirless management software (in my case Linksys Wireless Manager that came with the USB device) was interfering with my Windows XP Wireless Manager.Rule of thumb: Always let your native operating system manage the wirless networks that are available to it. It does a far better job and is 10x more reliable than software provided by 3rd party vendors.Specific to my case: Windows XP, I had to enable the Windows Wireless Manager and uninstall the Linksys Wireless Manager Software. Here it is...Enabling Windows Wireless Manager These directions are for Windows XP:
1) From the Windows Start menu, click Control Panel.
2) Click Network and Internet Connections.
3) Click Network Connections.
4) Right-click the icon for your "wireless network connection", then click Properties.
5) At the top of the window, click the Wireless Networks tab.
If the "Wireless Networks" tab does not appear between the "General" and "Advanced" tabs, you are not on/in the wireless network connection settings:a) click cancelb) Right-click the icon for your wireless connection and choose "Enable". c) return to step 4 6) Check the checkbox next to "Use Windows to configure my wireless network settings".
These directions are for Windows Vista:
1) Go to the Windows start menu and then the control panel.
2) Open Network and Sharing Center.
3) Click Manage Network Connections (from the left side menu).
4) Right click on the network adapter 'Wireless Network Connection' and choose "Properties" and click "Continue".
5) At the top of the window, click the "Wireless Networks" tab.
If the "Wireless Networks" tab does not appear between the "General" and "Advanced" tabs: a) click cancel b) Right-click the icon for your wireless connection and choose "Enable". c) Return to step 4
6) Check the checkbox next to "Use Windows to configure my wireless network settings".
I have been using the E3000 for quite a while. A problem that I could not find a solution to is that the devices connected through Ethernet can't be viewed on Wireless, and vice versa. This is especially annoying because I want to get access to my media servers over wireless, for obvious reasons, but even those are not viewable (and using IP addresses on portables is a pain in the back)
View 4 Replies View Related I am running an E3000 with Firmware - 1.0.04.
I would like to schedule my boys ipods to be on the network from 2:00pm to 4:00pm each day.
Running the Cisco connect software it would appear I can schedule from 2pm until the next morning but not a 2 hour window in the same afternoon.
Looking through other posts I see earlier software where this can maintained through the Router firmware but with 1.0.04 I seem to have to use Cisco Connect.
So how can this be done with my current configuration ?
I am running the e3000 as an access point.. My iphone and ipad connect to it seamlessly. After a few hours to days, they are no longer recognized by the router. Nothing I reset on the phone or ipad makes any difference. The only solution I have found is to re-boot the router. They then re-connect on their own.
View 4 Replies View RelatedI I use a Linksys E3000 router. Sometimes when I look at the network map I see a device called "Unknown." It appears as though the two notebooks sometime are going through this device to access the Linksys E3000. (I've checked when both notebooks are on and I can determine what devices are connecting directly to the router and what devices are going through this unknown device.) Is there any way to determine what this unknown device is?
View 5 Replies View RelatedWhat's happened is that after transferring my old PC's data onto my new one, and putting that one in place of my old one, therefore hooking up my modem to it, my wireless devices have been having trouble connecting to the router. Everything's hooked up fine, and it was working perfectly before, but now my devices such as my laptop and Droid Pro can SEE the router (As in connect to it and say that they are getting excellent signal strength), but when I try to open my browser, it asks as if I'm not connected to anything at all. The PC that's wired to the modem through the router works fine, however.
View 14 Replies View RelatedI have experienced some strange behavior of WiFi connection using WRT320N router. ISP provides me the internet in 2 modes (day and night). During day mode max speed is 24 Mb/s and during night 60 MB/s. Modem ADSL (Cisco EPC3010) is connected to Linksys WRT320N and on router is configured WiFi.Now issue. In the day mode everything is perfect. Cable connection gives me 24 MB/s and WiFi connection around 22 MB/s so not so bad. However when my internet speeds up to 60 Mb/s (cable connection via router gives exactly 60), WiFi connection instead speed up as well, just drop to max 17 Mb/s. I have tied several different settings on the router including changes in WiFi band, channel width, different channels (now channel is setup to 1 which is maybe not totally free but no so occupied) and others but unfortunately without significant improvement (in many cases connection just slowed down more).
And some details:
Wireless configuration (now)
Band: 2.4GHz
Mode: Wireless-N only
Channel Width: Auto (20MHz or 40 MHz)
Channel: 1
Wireless adaptor: Intel Centrino Advanced-N 6230 (I know that this doesn’t mean anything but Win7 shows that connection is established with speed 144MB/s)Router firmware and WiFi card updated to the newest version.
I have a E3000 with a USB hard drive plugged into it. It works perfectly as a shared storage drive from all my computers. But as a Media Server it is not working. I purchased a Sony SMP-N200 Steaming Media Server that found all the PCs in the house and can stream music and photos fine. It does not see the shared USB drive connected to the E3000. Sony's web site says it uses DLNA to find and stream music and photos. It says Windows 7 is one example of DLNA When I go to DLNA.org and check to see what routers are DLNA compliant, it says the Cisco E4200 and E4200v2 is. Is Cisco going to make a firmeware upgrade to include DLNA for the E3000?
View 6 Replies View RelatedI've used Netgear & other routers for years; I was able to see the devices connected over ethernet & wifi through the router configuration utility. Cisco's interface looks poor; there is no way to see the connected devices.Many of the devices I have have a 5 Ghz radio and some don't so i need to see at what speeds they are connecting at.Or does Cisco not provide this utility? I am surprised that a high-end product from Cisco does not have this function.
View 9 Replies View RelatedHow can I tell what devices are connected to my WRT54G?
View 4 Replies View RelatedSo i just set up the Linksys E2500 and it shoes 8 devices connected to my router. How I can see what devices are connected?
View 1 Replies View RelatedI upgraded to firmware version 1.0.03 I started to have this weird issue: I have four PCs connected to this wireless router via wireless G. They all run Windows 7 Home Premium. After a few hours I started to notice that the DHCP client table is empty even if all four PCs are connected to the internet. This causes a networking problem because one of the PC serves as a file server and it grants access by IP addresses. Not being able to "see" those computers, my access is denied.
View 2 Replies View RelatedHow can I tell the names of the devices that are connected to my E2000 router? Cisco connect says I have 4 devices connected but I only have 3. I am trying to figure out where the 4th device is coming from.
View 9 Replies View RelatedI have an EA 4500. Tonight I was trying to see what devices were connected. The window shows 0 devices connected, although about 20 devices are connected and working. When I click on "Devices Connected", I get the spinning wheel, and after multiple attempts by the application to list devices, I receive a message that the application does not work. I have the latest firmware installed. This is a recent issue. I have not made any changes to network configuration, nor to any of the devices that all have internet access. I will note that I did not set up a separate SSID for each band. But that did not seem to be an issue in previous months. I also cannot access the router ui from my windows 7 desktop. I can access the abbreviated ui through my Android phone. I tried connecting through smart wi-fi and by ip of the router. I just get the endless spinning circle of dots. I am running Windows 7 all up to date. All drivers are up to date.
View 7 Replies View RelatedMy EA6500 are not displaying all the connected network devices on in the GUI. How do i force this? Is it a bug? How can I make sure all my devices are showing in the GUI?
View 5 Replies View RelatedI am trying to find out what devices are connected to my router. I have had some illegal downloading from my IP address but it has not been done from my computer. It is showing in Cisco Connect that I have 15 devices connected, I should have no more than 6 devices connected so trying to figure out who is connected on my computer.
View 9 Replies View RelatedI've been searching how to make my E3000 use the DHCP and IP address on my primary router so I can share printers and computers on same gateway IP. I tried turning off DHCP on E3000, but not sure how to tell it to use the DHCP from the source "INTERNET"
View 1 Replies View RelatedHow can i turn off/on the wireless in Linksys E3000.
View 1 Replies View RelatedMy EA4500 with the latest firmware will only display nine connected devices at a time. It also seems to randomly shuffle which devices to show as connected, even though several more than nine are connected and online. Does anyone else's device list limit itself to displaying only nine devices? The Linksys phone apps also display a maximum of nine devices. I like the routers new user interface and understand that it has received a lot of praise, however this is the second bug I've experienced in as many months (the first being a failure of the device list to update once devices are upgraded to Windows 8, requiring a reset to default settings in order to fix).
View 5 Replies View RelatedFor a while now, my wireless network at home has been very unreliable. I posted on these forums before, asking for assistance to fix crashes that seemed to be random. I was largely unsuccessful, and the problem continued. However, as I continued to experiment with different methods to keep my network up and running, I noticed that as long as I had at least one device connected to the network around-the-clock it never crashed. This was easy enough, as I own an iPod touch and a dock (I would leave it sitting it the dock unlocked all the time). But it's annoying to never be able to leave the house with it, and I'm ready to finally get a solution to the problem once and for all. I would prefer not getting a new router, but if worse comes to worse I will.
To sum it up:
-Works perfectly (when up) at full speed, never crashes unless there are no devices connected to it.
-When it does crash, it is very difficult to 'coax' it back into working again; it's been down for weeks at a time before.
-For some strange reason (and maybe this is a clue), newer game systems such as a Nintendo DSi or PS3 can make it start working again. I, of course, own neither of these.
-I'm using a WRT160N V3, latest firmware as far as i know.
I cant see in my network the devices connected to SE2500 just the SE2500 itself. The internet access of the devices connected to SE2500 is working correctly. Is this a problem?
View 3 Replies View RelatedI'm thinking of upgrading from my Linksys WRT54G router to the E4200 and though I've goggled. Also, are there no LEDs on this unit to tell you the status of what's connected?
E3000WRT-54GWVC-80N
I have Att internet services and the modem I received from them has WiFi with it. The signal that it produces is very weak. I was curious if there is any way to use my E3000 to boost or repeat the signal so WiFi will extend through out the house.
View 4 Replies View RelatedI recently switched my router from an older Linksys WRT 54GS to an E3000. The WRT 54GS was working perfectly fine, but I needed to upgrade to a 802.11n router to use with some of my devices at home. I unplugged all the cables from the WRT54GS, and connected all the cables into the E3000 - in the exact same sockets and order they were on the old router. When powering on, all the lights eventually turned on (Power, Internet and Ports 1 to 4), except the wifi is still off. I tried running the installation CD, but it says it cannot find the network. I tried a reset (back button) as well as 30-30-30 reset, but no matter what I do, the wifi indicator still doesn't turn on. When switching back to the old router, it has no problem broadcasting a wifi signal again. Is there anything else I should try, either on my PC settings or the E3000 router itself?
View 5 Replies View RelatedI've made an observation that the newer routers above my E3000 don't have LED icons to indicate the port is connected/active and also to show Wi-Fi is active? I find this good at a glance without having to go look in the back of the unit to see which ports are open etc.
View 1 Replies View Relatedlost wireless to all wireless devices (laptop, iPhone and iPad). Still have hard wired ethernet internet access from desktop. Tried resetting router, powering off router, resetting and powering off cable modem. Nothing works. Lights on router all on.
View 1 Replies View RelatedSet channel manually - i've tried all the channels no luck
Different SSIDs for 5g and 2.4g
Beacon Interval 50
Fragmentation threshold 2306
RTS Threshold 2304
I'm running firmware 1.0.04 build 6 <script type="text/javascript"></script> Dec 6, 2010?I've had the router for 4 months now and this has been happening for the last 3.
I have the E3000 router. I set it up about a month ago and had my laptop and iphones and ipads all hooked up and working great. About two weeks ago, all of my devices are having problems connecting to the network and if they do connect, it is unstable (slow speeds or constantly dropping from the network). I know it is not the internet due to the fact that my LAN connection (hardwired) runs great. I am pulling my hair out trying to figure out why. I have restored to factory defauls and started over setting it up with no change in performance. I have the latest drivers on the router and the laptop. I thought maybe it was vista and my laptop or network card, but the fact that I cannot get my phones or ipads to connect with good performance I am starting to think it is something to do with the router. Also, just for more info, I am using Chater cable internet. I am running vista 64x on the laptop.
View 1 Replies View RelatedI have a E1200 router and it's pretty good however I've noticed that there are 12 devices connected to my router when infact there should only be 4 devices connected. I would like to see all the devices that are connected and disconnect the ones that don't belong
View 1 Replies View Related