Linksys Wireless Router :: Turn Off / On Wifi In E3000
Jul 3, 2011How can i turn off/on the wireless in Linksys E3000.
View 1 RepliesHow can i turn off/on the wireless in Linksys E3000.
View 1 RepliesI recently switched my router from an older Linksys WRT 54GS to an E3000. The WRT 54GS was working perfectly fine, but I needed to upgrade to a 802.11n router to use with some of my devices at home. I unplugged all the cables from the WRT54GS, and connected all the cables into the E3000 - in the exact same sockets and order they were on the old router. When powering on, all the lights eventually turned on (Power, Internet and Ports 1 to 4), except the wifi is still off. I tried running the installation CD, but it says it cannot find the network. I tried a reset (back button) as well as 30-30-30 reset, but no matter what I do, the wifi indicator still doesn't turn on. When switching back to the old router, it has no problem broadcasting a wifi signal again. Is there anything else I should try, either on my PC settings or the E3000 router itself?
View 5 Replies View RelatedI got a problem with my setup main computer, It work wery god wireless, with very fine speed about 82 mbit in and 24 mbit out. The problem is that it almost dont work at all with cable, even if i turn off the wireless network, the speed is about 2-3 mbit in and about 6-7 mbit outAll other computers, tv. printer wireless work very fine.
View 1 Replies View RelatedI've been having trouble with my wrt54gs2 and 4 360's. I tried a link someone posted for me to a cisco tutorial, it worked, but only for one 360. I have a Netgear wndr3400, I HATE the wireless on that router. Its unreliable but I like the features, the guest network and transfer meter, plus its worked with 4 360's out of the box. So would it be possible to turn off my wifi on the Netgear and plug the wrt54gs2 in and use its wireless?
View 7 Replies View RelatedI have a Linksys WRT120N wireless router. I am currently only using wired connections to the router. I recently bought a Nexus 7 tablet computer and would like to connect to the Internet wirelessly. How do I turn on the wirelss capability of my router securely?
View 3 Replies View RelatedI've been searching how to make my E3000 use the DHCP and IP address on my primary router so I can share printers and computers on same gateway IP. I tried turning off DHCP on E3000, but not sure how to tell it to use the DHCP from the source "INTERNET"
View 1 Replies View RelatedI have Att internet services and the modem I received from them has WiFi with it. The signal that it produces is very weak. I was curious if there is any way to use my E3000 to boost or repeat the signal so WiFi will extend through out the house.
View 4 Replies View RelatedI've made an observation that the newer routers above my E3000 don't have LED icons to indicate the port is connected/active and also to show Wi-Fi is active? I find this good at a glance without having to go look in the back of the unit to see which ports are open etc.
View 1 Replies View Relatedlost wireless to all wireless devices (laptop, iPhone and iPad). Still have hard wired ethernet internet access from desktop. Tried resetting router, powering off router, resetting and powering off cable modem. Nothing works. Lights on router all on.
View 1 Replies View RelatedSet channel manually - i've tried all the channels no luck
Different SSIDs for 5g and 2.4g
Beacon Interval 50
Fragmentation threshold 2306
RTS Threshold 2304
I'm running firmware 1.0.04 build 6 <script type="text/javascript"></script> Dec 6, 2010?I've had the router for 4 months now and this has been happening for the last 3.
I have the E3000 router. I set it up about a month ago and had my laptop and iphones and ipads all hooked up and working great. About two weeks ago, all of my devices are having problems connecting to the network and if they do connect, it is unstable (slow speeds or constantly dropping from the network). I know it is not the internet due to the fact that my LAN connection (hardwired) runs great. I am pulling my hair out trying to figure out why. I have restored to factory defauls and started over setting it up with no change in performance. I have the latest drivers on the router and the laptop. I thought maybe it was vista and my laptop or network card, but the fact that I cannot get my phones or ipads to connect with good performance I am starting to think it is something to do with the router. Also, just for more info, I am using Chater cable internet. I am running vista 64x on the laptop.
View 1 Replies View RelatedMy E3000 has been working fine with 1.0.04 build 6 FW. Recently some devices (kindle, iPad) can't connect to internet while connected to E3000 via WiFi network. Had a look my E3000 router IP is 192.168.0.1 but those problematic devices has IP 192.168.1.XXX allocated by DHCP not sure why. Currently I manually set up static IP 192.168.0.XXX for those devices.
View 1 Replies View RelatedThis is another E3000 "connection drops" thread. Some background: I have two E3000's that are cascaded. The main router is in my basement connected to my cable modem and is my DHCP server. The second one is on the main floor and provides my wireless signal (no DHCP, and is hard connected to the main router).I have lots of connection drops with the wireless router on the main floor. Lately I have noticed a trend, though. My connection drops mostly when I browse my network (usually browsing pictures on another computer) or when large files or videos are being transferred. If I connect a cable, I have no problems. When wireless, I have signal drops.I have tried every trick and tip that I've seen on this forum or been provided in the Linksys FAQ. I've changed the beacon interval, fragmentation threshold to 2306 and CTS to 2307, I've tried changing channels, I've checked and unchecked boxes for NAT, Filters, etc. I've tried different combinations of WPA2 passwords. I've tried dynamic routing, static routing, blah blah blah...
When I set the 5Ghz channel to Auto(DFS) it defaults to channel 36 and 144Mbps. When I use other channels, I get 300Mbps. Either way, my connections still drops.
I have the latest firmware 1.0.04 Build 6.I even have the router sitting on top of a laptop cooling pad to keep it cool.No matter what I do, as soon as I start browsing my network the wireless connection drops.I am so frustrated! I upgraded my WRT-160N to this E-300 router to get the faster speed and dual band but have had nothing but trouble. I never had a connection drop with my 160N.
EDIT: I notice that when my signal drops, I can see the power LED blinking on the router, like it's going through a reboot cycle.
I've recently upgraded my home network and now my wdtv can't connect to my shared hdd's on my pc for streaming purposes. Previously I had some piece of **bleep** G router/modem combo from Verizon and I didn't have any problems accessing my network shares, I did have a streaming problem with some .mkv's because the signal was so poor. I Finally dropped some cash on a d-link modem and an linksys E3000 router. Here's the messed up part, if my wdtv is plugged, physically, into my router I can access my shares just fine. I can stream movies with out any lag what so ever. If I go wireless (as I have previously been with the old westell router/modem combo) I can no longer see my network shares. I can connect to the internet and do netflix, pandora, ect. But when I go under network shares all that shows up is my router..
View 1 Replies View RelatedI've got a 2 month old e3000 with the latest firmware. (1.04 i believe) I have run speedtests from wired and wireless machines on my network. All of the wired connections show a speed of around 15Mps (which is consistent with my providers guaranteed speed) but when I test any of the wireless connections I get somewhere between 3 and 7 Mps. I get the same degradation in speed when I stand directly next to the e3000.
Other then SSID and Passphrases I have everything set to the default settings. I have rebooted multiple times with no change. The e3000 is mounted on a 2x4 with several feet of clearance all around and is also located in the coolest part of the house. I am using Speedtest.Net for all the tests.
I am trying to connect my DishNetwork DVR up via a wireless link to the E3000.My home network consists of a Linux Server acting as a router/gateway for a DSL link, with several pc's (XP/MAC/Linux) connected on a local 10/100 lan.The existing lan addressing scheme uses static IP's and the DVR requires a DHCP link.I thought the E3000 would solve that issue by using it's DHCP server capability to host the DVR wirelessly and integrate it into the rest of the lan.I set up the DHCP and reserved an IP address, which the DVR pick's up just fine, but although I can ping the gateway and DVR in both directions, I am unable to access the internet.I've tried to set up a static route, but I think I'm not doing it correctly. [code]
View 9 Replies View RelatedI am running an E3000 router with 1.0.04 build 6 Dec 6, 2010 firmware. I have two computers on a wired Gigabit LAN and others on WiFi (802.11g). At first, all works well and I get normal throughput via the WiFi computers.However, after about a week, WiFi speeds crawl to a fraction of what I normally get (from 12-13 Mbps down to 1-2 Mbps and from 4.8 Mbps up to less than 1 Mbps). My cable modem service is 40 Mbps down and 5 Mbps up (I get 38.9 down and 4.9 up via the LAN based computers)
How I resolve this? I need to reboot the router! Once it comes back on-line, my throughput on WiFi is restored UNTIL the following week where speeds are back to a crawl. While WiFi crawls, the LAN based computers still enjoy maximum throughput.
I have Comcast cable internet routed through a linksys E3000 router. My desktop is connected to my router via ethernet and my various other devices including my laptop are wifi connected. It seems almost at random that my desktop will lose its connection.Windows will show me as still being connected and my network connection will show a normal status until I atttempt to repair it then it will change to limited or no connectivity. Through all of this, my other devices all still have a wifi signal (I don't use more than 1 or 2 at the same time). I can reconnect to the internet by unplugging my ethernet cable then reuplugging it back in and my connection will start working again. I've also had several blue screens, and when I checked the dmp files it revealed my network card driver as the culprit, yet I have reinstalled and even clean installed the microsoft signed driver. I have also attempted to reboot both my modem and router to no avail.
Microsoft XP
Marvell Yukon ethernet adapter on a biostar mobo
C:Documents and SettingsMain>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : sn1
Primary Dns Suffix . . . . . . . :
[code]...
How can I turn off the wi-fi on WAG160Nv2?Upon entering it I find no option that says Disable Wireless.
View 5 Replies View Relatedhow can you turn my wifi router into a simple wired one
View 3 Replies View RelatedI wish to turn my TP-Link wireless router into an access point but can't figure out how to do it. I have tried several times but without any success. Below are my information about my main router and the router I want to turn into an access point:
1- Main Router: TP-LINK 3G/4G Wireless N Router 300Mbps - Model No. TL-MR3420. url..
2- Router I wish to turn into an access point:TP-LINK Wireless N Router 150Mbps - Model No. TL-WR740N. url...
turning my wireless back on. Some how in attempting to create a shared file between my pc and my wife's Mac the wireless has been disabled. I have tried resetting the device several times following the instructions on line however I still can not get the wireless to re activate. I tried reverse directions from the posts on how to turn off the wireless but still no luck. I tried restoring the computer to a later date?
View 2 Replies View RelatedHow do I turn off the SIP ALG?
View 1 Replies View RelatedFirmware 1.0.00 on my E4200 Hardware v1.0 provided a functioning 6to4 tunnel through Comcast's 6to4 facility. Windows and Linux clients on my local network discovered IPv6 addresses and were able to use them successfully.Unfortunately, after the upgrade to 1.0.03 this functionality was gone. I missed reading the ChangeLog, which said that the automatic tunneling feature was removed in 1.0.01. The now provided IPv6 functionality works much less well. First, automatic configuration (discovery of the 6to4 via IPv4 anycast) no longer works with Comcast's gateway. If I configure the tunnel manually, by specifying a 2002/16 prefix, I regain IPv6 connectivity, but only for Linux clients on my local network.
Windows 7 clients suffer from the problem that because the E4200 hands out ULA addresses, they end up preferring those ULA addresses when making global IPv6 connections in the IP 'source' field, which of course does not work. It's like putting your company mailbox code as the return address on a letter you send via US Mail. Other home routers, such as the AVM Fritz! (url,...) suffer from the same problem. However, they provide an option to turn off ULA at the router.Is it possible to turn off ULA for the E4200?
If the wifi can be turned off on the E1500. I got this unit from a family member and do not need the wifi part, as I have two computers, but are in the same room. I have the cisco connect on my computer and do not see a disable wifi in the program anywhere.
View 1 Replies View RelatedI have a WRT54G router, and when I am in the security area, where you choose WPA, WEP, etc... I keep clicking the dropdown menu, and when I choose anything BUT disable, the security auto-sets back to disable. I have rebooted the router. I have rebooted the modem. I have changed my router's password.How do I turn my WEP back on without it just saying. Also, for additional notation, my US light on my modem is no longer green, it is orange since this issue has occured. Is there any connection that might be related to this?
View 8 Replies View RelatedMy WRT610n went out today for no apparent reason.All of my other peripherals are still running, but the router won't turn on. I've tried different transformers, outlets and powerstrips, with no luck -- no power. I've also tried a hard reset on it, with no luck.
View 3 Replies View RelatedI just got a Linksys 1200 wireless router and wanted to know how (and the best way) I can turn it off (besides unplugging it) when I am out of town?
View 3 Replies View RelatedI can't turn WI-FI on in my Toshiba A 665, Win 7. At the biginning worked good ,than vanished. Checking Fn > F8 below main icon (with an antena ) do not show up other four icons below, like they suppose to do. So I'm not even able to try to turn it on. Restarting doesn't do at all. Pushing Wi-fi switch, above the keybord, doesn't even show On/of icon.
View 7 Replies View RelatedHow do I turn on jumbo frames on the e3200? I am using 1.0.01 firmware.
View 3 Replies View RelatedEA3500, I'm using the Smart Wi-Fi interface through a browser. How do I make my router broadcast the SSID? I think it was when I was setting up using the old interface, before updating the firmware, that I set it to *not* broadcast the network name. Now I feel like I've been all through the menus twice on the Smart Wi-Fi interface, and can't find the on/off toggle.
View 9 Replies View RelatedI just set up my new Linksys 3200 router and wanted to know if i should turn SSID boradcasting feature off?
View 2 Replies View Relatedwhen i bought the router, the function worked fine, even before my first firmware upgrade. Can CISCO fix this? I tried everything...power off, reboot, etc...that stupid button is not working....
if something as simple doesn't work, what's next on this router to break?