I've been searching how to make my E3000 use the DHCP and IP address on my primary router so I can share printers and computers on same gateway IP. I tried turning off DHCP on E3000, but not sure how to tell it to use the DHCP from the source "INTERNET"
View 1 Replies
When I click on "DHCP Reservation" button in the web interface of the E3000 I don't see any information about the current devices and the reservation list.This problem occurs when my sattelite reciever tries to get an IP address from the DHCP.the name of the receiver is "dream box" (no special characters).I didn't have any problem in the past with my previous router (3COM)Since there are error messages in the page (screenshot is attached), I've tried to use different browsers but the result was the same (Firefox, Safari, IE 8)
View 9 Replies View RelatedI have Linksys E3000 Router and it is connected to 7 Devices at this moment via DHCP. I have got New NAS Enclousre (8th Device) which has got Lan port . I have connected Box to One free Port on E3000 Router. I see DHCP Reservation from 192.168.0.1 assging one IP to My NAS Enclosure Box i.e 192.168.0.13 But when i ping that box . It's not pingable. When i try to browse that NAS Enclosure's setup web page - it's not opening. I can access that box setup page if i connect direct 1:1 Lan cable over private network (169.254.XXX). It means web server is runing on box. I am clueless. E3000 is assigning IP to NAS Enclosure but can't Browse or Ping. I tried to Assign Manual IP address to NAS enclusure and reconnect to router. Still I can't ping or browse.
#arp -a show that box has IP. (Output from MAC os) .
? (192.168.0.13) at (incomplete) on en0 ifscope [ethernet]
Ping test from Router Page.
PING 192.162.0.13 (192.162.0.13): 32 data bytes
40 bytes from 192.162.0.13: icmp_seq=0 ttl=46 time=286.6 ms
40 bytes from 192.162.0.13: icmp_seq=1 ttl=46 time=290.2 ms
[code]....
I upgraded to firmware version 1.0.03 I started to have this weird issue: I have four PCs connected to this wireless router via wireless G. They all run Windows 7 Home Premium. After a few hours I started to notice that the DHCP client table is empty even if all four PCs are connected to the internet. This causes a networking problem because one of the PC serves as a file server and it grants access by IP addresses. Not being able to "see" those computers, my access is denied.
View 2 Replies View RelatedHow can i turn off/on the wireless in Linksys E3000.
View 1 Replies View RelatedI have Att internet services and the modem I received from them has WiFi with it. The signal that it produces is very weak. I was curious if there is any way to use my E3000 to boost or repeat the signal so WiFi will extend through out the house.
View 4 Replies View RelatedI recently switched my router from an older Linksys WRT 54GS to an E3000. The WRT 54GS was working perfectly fine, but I needed to upgrade to a 802.11n router to use with some of my devices at home. I unplugged all the cables from the WRT54GS, and connected all the cables into the E3000 - in the exact same sockets and order they were on the old router. When powering on, all the lights eventually turned on (Power, Internet and Ports 1 to 4), except the wifi is still off. I tried running the installation CD, but it says it cannot find the network. I tried a reset (back button) as well as 30-30-30 reset, but no matter what I do, the wifi indicator still doesn't turn on. When switching back to the old router, it has no problem broadcasting a wifi signal again. Is there anything else I should try, either on my PC settings or the E3000 router itself?
View 5 Replies View RelatedI've made an observation that the newer routers above my E3000 don't have LED icons to indicate the port is connected/active and also to show Wi-Fi is active? I find this good at a glance without having to go look in the back of the unit to see which ports are open etc.
View 1 Replies View Relatedlost wireless to all wireless devices (laptop, iPhone and iPad). Still have hard wired ethernet internet access from desktop. Tried resetting router, powering off router, resetting and powering off cable modem. Nothing works. Lights on router all on.
View 1 Replies View RelatedSet channel manually - i've tried all the channels no luck
Different SSIDs for 5g and 2.4g
Beacon Interval 50
Fragmentation threshold 2306
RTS Threshold 2304
I'm running firmware 1.0.04 build 6 <script type="text/javascript"></script> Dec 6, 2010?I've had the router for 4 months now and this has been happening for the last 3.
I have the E3000 router. I set it up about a month ago and had my laptop and iphones and ipads all hooked up and working great. About two weeks ago, all of my devices are having problems connecting to the network and if they do connect, it is unstable (slow speeds or constantly dropping from the network). I know it is not the internet due to the fact that my LAN connection (hardwired) runs great. I am pulling my hair out trying to figure out why. I have restored to factory defauls and started over setting it up with no change in performance. I have the latest drivers on the router and the laptop. I thought maybe it was vista and my laptop or network card, but the fact that I cannot get my phones or ipads to connect with good performance I am starting to think it is something to do with the router. Also, just for more info, I am using Chater cable internet. I am running vista 64x on the laptop.
View 1 Replies View RelatedMy E3000 has been working fine with 1.0.04 build 6 FW. Recently some devices (kindle, iPad) can't connect to internet while connected to E3000 via WiFi network. Had a look my E3000 router IP is 192.168.0.1 but those problematic devices has IP 192.168.1.XXX allocated by DHCP not sure why. Currently I manually set up static IP 192.168.0.XXX for those devices.
View 1 Replies View RelatedThis is another E3000 "connection drops" thread. Some background: I have two E3000's that are cascaded. The main router is in my basement connected to my cable modem and is my DHCP server. The second one is on the main floor and provides my wireless signal (no DHCP, and is hard connected to the main router).I have lots of connection drops with the wireless router on the main floor. Lately I have noticed a trend, though. My connection drops mostly when I browse my network (usually browsing pictures on another computer) or when large files or videos are being transferred. If I connect a cable, I have no problems. When wireless, I have signal drops.I have tried every trick and tip that I've seen on this forum or been provided in the Linksys FAQ. I've changed the beacon interval, fragmentation threshold to 2306 and CTS to 2307, I've tried changing channels, I've checked and unchecked boxes for NAT, Filters, etc. I've tried different combinations of WPA2 passwords. I've tried dynamic routing, static routing, blah blah blah...
When I set the 5Ghz channel to Auto(DFS) it defaults to channel 36 and 144Mbps. When I use other channels, I get 300Mbps. Either way, my connections still drops.
I have the latest firmware 1.0.04 Build 6.I even have the router sitting on top of a laptop cooling pad to keep it cool.No matter what I do, as soon as I start browsing my network the wireless connection drops.I am so frustrated! I upgraded my WRT-160N to this E-300 router to get the faster speed and dual band but have had nothing but trouble. I never had a connection drop with my 160N.
EDIT: I notice that when my signal drops, I can see the power LED blinking on the router, like it's going through a reboot cycle.
I've recently upgraded my home network and now my wdtv can't connect to my shared hdd's on my pc for streaming purposes. Previously I had some piece of **bleep** G router/modem combo from Verizon and I didn't have any problems accessing my network shares, I did have a streaming problem with some .mkv's because the signal was so poor. I Finally dropped some cash on a d-link modem and an linksys E3000 router. Here's the messed up part, if my wdtv is plugged, physically, into my router I can access my shares just fine. I can stream movies with out any lag what so ever. If I go wireless (as I have previously been with the old westell router/modem combo) I can no longer see my network shares. I can connect to the internet and do netflix, pandora, ect. But when I go under network shares all that shows up is my router..
View 1 Replies View RelatedI've got a 2 month old e3000 with the latest firmware. (1.04 i believe) I have run speedtests from wired and wireless machines on my network. All of the wired connections show a speed of around 15Mps (which is consistent with my providers guaranteed speed) but when I test any of the wireless connections I get somewhere between 3 and 7 Mps. I get the same degradation in speed when I stand directly next to the e3000.
Other then SSID and Passphrases I have everything set to the default settings. I have rebooted multiple times with no change. The e3000 is mounted on a 2x4 with several feet of clearance all around and is also located in the coolest part of the house. I am using Speedtest.Net for all the tests.
I am trying to connect my DishNetwork DVR up via a wireless link to the E3000.My home network consists of a Linux Server acting as a router/gateway for a DSL link, with several pc's (XP/MAC/Linux) connected on a local 10/100 lan.The existing lan addressing scheme uses static IP's and the DVR requires a DHCP link.I thought the E3000 would solve that issue by using it's DHCP server capability to host the DVR wirelessly and integrate it into the rest of the lan.I set up the DHCP and reserved an IP address, which the DVR pick's up just fine, but although I can ping the gateway and DVR in both directions, I am unable to access the internet.I've tried to set up a static route, but I think I'm not doing it correctly. [code]
View 9 Replies View RelatedI am running an E3000 router with 1.0.04 build 6 Dec 6, 2010 firmware. I have two computers on a wired Gigabit LAN and others on WiFi (802.11g). At first, all works well and I get normal throughput via the WiFi computers.However, after about a week, WiFi speeds crawl to a fraction of what I normally get (from 12-13 Mbps down to 1-2 Mbps and from 4.8 Mbps up to less than 1 Mbps). My cable modem service is 40 Mbps down and 5 Mbps up (I get 38.9 down and 4.9 up via the LAN based computers)
How I resolve this? I need to reboot the router! Once it comes back on-line, my throughput on WiFi is restored UNTIL the following week where speeds are back to a crawl. While WiFi crawls, the LAN based computers still enjoy maximum throughput.
My router a E4200. the thing is i want to disable the dhcp services from the router, because there are allready a dhcp server in my network. but if i disable the dhcp will the Guest wifi functions still work?
View 3 Replies View RelatedCould I use DHCP for wireless connection and assign private IP for PC for wire connection ?Will it conflict to each other ?
View 3 Replies View RelatedI have Comcast cable internet routed through a linksys E3000 router. My desktop is connected to my router via ethernet and my various other devices including my laptop are wifi connected. It seems almost at random that my desktop will lose its connection.Windows will show me as still being connected and my network connection will show a normal status until I atttempt to repair it then it will change to limited or no connectivity. Through all of this, my other devices all still have a wifi signal (I don't use more than 1 or 2 at the same time). I can reconnect to the internet by unplugging my ethernet cable then reuplugging it back in and my connection will start working again. I've also had several blue screens, and when I checked the dmp files it revealed my network card driver as the culprit, yet I have reinstalled and even clean installed the microsoft signed driver. I have also attempted to reboot both my modem and router to no avail.
Microsoft XP
Marvell Yukon ethernet adapter on a biostar mobo
C:Documents and SettingsMain>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : sn1
Primary Dns Suffix . . . . . . . :
[code]...
I have a Linksys E3000 router set as Lan-Lan 192.168.0.2 hosting my internal LAN connected to a motorola Surfboard (Brighthouse) internet Wireless/Wired access point 192.168.0.1.I have a Web server hosting a site connected direct to the surfboard (works fine) . The FTP "site" on the E3000 can be seen by all pcs on the internal LAN. However, it can NOT be seen from the internet (Android with FTP client being used for test device)
Primary Access point 192.168.0.1
DCHP server with reserved IP addresses for server and PC's and smartphones
Port Forwarding Set for Server at 0.004 : 80
Port Forwarding Set for E3000 at 0.002 :21
Secondary (E3000) router 192.168.0.2
DCHP server is disabled
Port Forwarding is Not being used
connected to primary router LAN port 1 by LAN port 1 on E3000
All pc's can access the Internet when connected to the E3000 via cable or wireless?All pc's can access the FTP server on E3000 via cable or wireless as a LAN location (connected to either router)?How can I get the FTP to be seen from the internet ?
I recently bought a Cisco e3000 router. I updated the firmware but I am still only getting 1.33 Mbps at most. The only things plugged into it is my PC and my xbox. I bought the router so i could get a better connection on my xbox so netflix wont stop playback.
View 9 Replies View RelatedI have an e3000 that cannot obtain an address from the ISP. I can get an address on the computer and an old router by directly connecting the cable to the computer or the router. I can also daisy-chain the e3000 to the old router, and I can get an address on the e3000 from the old router. I have hard reset the e3000, changed firmware from the Linksys to TomatoUSB and back to Linksys, and I still can't get it to work. It worked fine on Saturday until a bolt of lightning hit close to the house. Since then, I cannot get the e3000 to connect to the ISP.
View 9 Replies View RelatedHow do you set up the E3000 for ATT u-verse?
View 2 Replies View Relatedinstall linksys e3000.
View 1 Replies View RelatedI had a failed Tomato upgrade and now Connect Setup can't see router to revert back to original. I get message 82BD0101 or computer not connected to router. Also the http://192.168.1.1 trick won't work. Is there any way to restore besides 30/30/30?
View 2 Replies View RelatedI would like to override the DNS servers provided by DHCP via my ISP. The other settings I would like to preserve (like my assigned IP).How to achieve this with E3000 ?
View 3 Replies View RelatedIt seems like after a certain amount of time, maybe a few days... my E3000 gets slowww.. I'm talking dog slow. And it's not just the internet, I have a media server connected to it, and usually when I put something on it, the transfer rate is about 3.5MB/s (not bits, bytes). But everything is slow, I top out at speed of maybe 1/6 normal on the internet as well.
View 8 Replies View RelatedWe have a wireless internet service. Not satellite. We basically have an antenna on our house that picks up the signal from a tower a mile or two away. I used the e3000 router when we lived in town with broadband internet and it worked fine. I can't get it to keep a hold of a signal. I can connect to the router from the computers but the router drops the signal from the tower. I have an old router that the wireless company was kind enough to lend me that works , but the signal is weak and it could die at any moment... I"m at my wits end.. I have an expensive piece of equipment that wont hold the signal. I have updated the firmware and the Cisco connect software..
View 5 Replies View RelatedHas anyone tested QoS on the new E3000? Whenever I add an application (e.g. Voice Device) and set priority to Medium or High, my upstream bandwidth for everything else is immediately cut significantly, even when I'm not using the priority application.
For example, with QoS disabled, I can consistently get 10Mb upstream (speedtest.comcast.net). As soon as I enable QoS, upstream is capped to exactly 2Mb! On my old router, there was an option to set the total upstream bandwidth -- but on the E3000 there is no such option that I can find.
just bought an e3000 and want to use it with wireless internet- usb modem. when setting up it wouldnt go any further than the 'searching for connection' page as it couldnt detect a connection in the 'internet' lan (wan?) port.can i set it up to accept the wireless usb modem?
View 6 Replies View RelatedI lost my cd for my router e3000 any way still to use it?
View 1 Replies View RelatedI just bought an E3000 about 30 hours ago and just unrealistically my router now doesn't want to give me any WiFi at all. I tried reset button, tried re plugin all of my system as well as pressing for short and long period the middle button that indicates WiFi is accessible. I already bought 3 linksys routers.
View 2 Replies View Related
