Linksys Wireless Router :: E3000 DHCP Client Table Not Showing Connected Device
Jan 10, 2011
I upgraded to firmware version 1.0.03 I started to have this weird issue: I have four PCs connected to this wireless router via wireless G. They all run Windows 7 Home Premium. After a few hours I started to notice that the DHCP client table is empty even if all four PCs are connected to the internet. This causes a networking problem because one of the PC serves as a file server and it grants access by IP addresses. Not being able to "see" those computers, my access is denied.
View 2 Replies
ADVERTISEMENT
Oct 29, 2011
I just purchased an E4200 router. I have four clients on my network and they are all set up for DHCP. I renewed their IPs and they all are connected. "Cisco Connect" reports that I have four clients connected. When I access the router and bring up the DHCP Client Table, there are no entries. There should be four entries. Aftern I enable the logging function, none of the logs have any data in them even after I wait for 45 minutes and use the internet and renew IPs. I am using Firmware Version: 1.0.03. I have the same results for both Chrome and Firefox. I want to be able to set Static IPs but I am hampered by the not having any clients in the DHCP client table.
View 9 Replies
View Related
Nov 30, 2011
My BEFSR81 is my primary router and has DHCP turned on. The router's DHCP range is set to accommodate 12 devices. I have three computers wired to it and their Host names (as specified in the set-up of each computer) show up in the router's DHCP device table. I also have two printers (one old Brother HL5250DN laser printer and one new HP Photosmart Premier C410a inkjet printer) connected and there are blanks where the Host name should go. I would like to be able to tell which printer is which when I am looking at the DHCP device table. How can I get a names associated with each printer's IP address in the router's DHCP device table? (The real problem is that the router seems to have both printers at the same IP address (192.168.1.100) and if I can get one of them to change I'd like to know which one it was!)
View 1 Replies
View Related
Jun 2, 2012
I just got an EA3500 and I guess I don't understand what "Refresh" does when viewing the DHCP client table under the "Status", "Local Network" tab of the web interface, either that or it's not working. If I have active wired and wireless clients and I power off the EA3500, wait a few minutes, then power it back on, the table is blank. If I hit "Refresh" I would expect it to re-populate the table with the connected clients. For whatever reason, it doesn't. I have to physically disconnect and reconnect the E-net cable, or power cycle the wireless client to get them to reappear in the table. Is something wrong with the router or its s/w
View 9 Replies
View Related
Aug 22, 2012
My EA4500 will periodically clear out the DHCP Client Table and I will lose internet access.This happens once almost every day, normally in the morning. If I can't access the internet I will check the DHCP client table under Status -> Local Network -> DHCP Client Table and it is always empty.After I select Setup -> Reboot it will work again - when I look at the DHCP client table it is now populated with all my devices. I am on firmware version 2.0.37.
View 3 Replies
View Related
May 20, 2012
I'd like to add a name to a few ip addresses in the DHCP client table currently there is an asterix for a couple client names. the router is an ea3500.
View 2 Replies
View Related
Jun 5, 2012
I have DHCP enabled, but I have assigned a static IP to most of my network devices.When I click on the DHCP Client Table, most of the devices are NOT shown even though I know they are connected and working.One device (a Brother printer) that I have assigned a static IP to actually shows up as having an IP from the DHCP range. A Panasonic TV does not show up at all even though it is connected and woking. I have not been able to assign a static IP to it because it does not show up.
View 3 Replies
View Related
Aug 7, 2006
I recently installed a WRT54G wireless router however I has this same question about my BEFSX41 Wired router.
View 9 Replies
View Related
May 2, 2013
I have the WRT400N router with the latest firmware. Recently I have noticed a device in my DHCP that I do not recognize. It is not device I own (believe me, I have racked my brain and confirmed) as it shows as an Acer pc. I cannot ping the IP address however. I have rebooted my router several times thinking maybe it's a former connected device but saved in memory but it keeps coming back. I am thinking possibly it is someone hi-jacking my Internet, but not sure. I am using WEP security but it shows a LAN connection which is strange for a wireless device. The only hard wired pc is my HP.
View 3 Replies
View Related
Aug 25, 2011
I have purchased E2500 and i am having following problems:
1. DHCP client list not showing - only shows when i reboot the router. After some time, the list never shows even when i press refresh button
2. I can only reserve IP when i reboot the router - after some time i cannot do this action also
I have upgraded to latest firmware and also peformed reset as directed by support.
View 1 Replies
View Related
Jan 31, 2011
Most devices pass a client name to DHCP when requesting an IP, but some like my smartphone, do not. When a device does not pass a client name garbage is entered as the name of the client name.The first is that when you use the Web Admin pages, and select Status/Local Network/DHCP Clients, the table will not display any clients because there is an error on the page. If you right click and View Source from the browser, you will see all the client entries are there and one of them will have garbage (unprintable characters) for the client name.The second and more serious issue is that the internal DHCP table once corrupt is unstable. I've had my BEFSR41 reboot because of the corruption and then I get IP conflicts on my LAN because the DHCP starts handing out in-use IPs.I'm on hardware version 4.3 and the latest firmware Ver.2.00.4 Build 8 (which is very difficult to install without bricking the router). BTW, when I use a WRT54GL router with the smartphone, it is properly handled by the DHCP and shows a blank client name, not garbage.
View 3 Replies
View Related
Apr 21, 2013
Do the problem caused by the modems itself or it just sign of faulty Ethernet switch (using 20 port Allied Telesis ethernet switch).
Sometimes I cannot connect to internet due to "unidentified network" buy i can resolve this problem by restarting my modem + switch.
View 4 Replies
View Related
Jun 21, 2011
how I can get to the DHCP client table on a Cisco 891 Router ? We just upgraded our router from a WRVS4400N to the Cisco 891. THe WRVS4400N has the feature DHCP client table that I can see the Client host Name and IP address,Mac Address I have CCP and CCP express installed on my system?
View 1 Replies
View Related
Jan 28, 2012
I have a WAP54g set up as a repeater. It even shows in the WRT54g device list (Tomato firmware) as a WDS interface but nothing can connect to it. I have the repeater's MAC address in the AP and it's set to "Access Point + WDS" mode. I don't know what I could be doing wrong. Is it a conflict of DHCP on the AP vs static on the repeater?
View 1 Replies
View Related
May 12, 2013
I tried to enter a name that included an illegal character (in this case, a single quote), and it gave me the popup box that said I had done so. When the popup closed, my DHCP reservation table was emptied out (I had maybe 5-6 reserved clients). In fact, I can't add new reservations anymore at all from this screen as it lists nothing in the DHCP clients table at the top. (Note, there are plenty of things in the DHCP Clients table over on the Status->Local Network tab). At this point, I think that my pre-existing reservations are still being held, but I'm not sure as it's only been about an hour so nothing has renewed.
I had firmware 1.0.05 when I encountered this problem. I upgraded to 1.0.07 as a means of trying to kick it into action, but the problem still exists.
View 1 Replies
View Related
Sep 24, 2011
my researvation table is incomplete. Below I show ipconfig that shows wired & wireless NICs assigned ip addresses by the E3200 router but the DHCP table only shows one.
I need to reserve the ip address of the wired address but can't get at it.
View 2 Replies
View Related
Jan 29, 2012
My E3200 has been clearing it's DHCP table at random times. When it's been cleared the router starts handing out duplicate addresses. It's running the latest (1.0.02 build 9 Sep 1, 2011) firmware and otherwise seems to be working fine.
View 9 Replies
View Related
Jan 11, 2012
I have 2 Media Bridges, a Trendnet TEW-640MB and TrendNet TEW-680MB. Both are set as a Static IP on the devices 192.168.1.150 and 192.168.1.151. In the DHCP table for my E4200 I don't see those. I have no problem accessing them typing in those IP addresses but wondering why they don't show up in the table.Actually looking at it more closely, the devices hooked up that are active seem to show up.So I see the following below. And where is list LAN but no name those seem to be devices connected to the media bridges.
LAN192.168.1.128 LAN192.168.1.129 iPhoneWireless192.168.1.130 1 Wireless192.168.1.131 LAN192.168.1.135
View 2 Replies
View Related
Oct 14, 2012
On my old Linksys WRT54GL router (with its latest stock firmware)'s http://192.168.1.1/DHCPTable.asp for DHCP Active IP Table, it only shows wireless connections. How come it doesn't show wired ones?
View 5 Replies
View Related
Jul 15, 2011
One of the many things that I liked about the e4200 over my olg 54GL was the fact that I could reboot it remotely. However, I've recently had a few problems that only a full power down would fix. In addition, I've noticed that the DCHP client table doesn't reset when I do a soft reboot. Is this intentional? Is the soft reboot not really a full reboot? Can it be made a real reboot?
View 7 Replies
View Related
Nov 27, 2012
I have an EA4500 and am using Cisco Connect Cloud software. Its working mostly fine except that I have one device on the network that will not show up in the device list. This is not an issue in itself and normally I would ignore (although it used to show up when I forst got the router) however..
The device is a WDTVLive media unit and required access to windows shares on a media server. Now the WDTVLive device is server an ip address by the router and is available from everywhere on my network but every couple of days it loses the capacity to search windows shares.
I know what you are thinking and I initially thought the same, this is an issue with the WDTVLive box. However one day I spent a few hours trying to resolve (Am an IT Consultant and know a little about networks) and found that I could not fix the issue. I then rebooted the router and it started working. I have since confirmed that every time it breaks I have to reboot the router.
View 7 Replies
View Related
Sep 26, 2012
Experienced problems with guest network not showing up as an available network on a device (laptop, iPad, etc)?I double checked if guest network is enabled on a EA3500 router. What other steps can I take?
View 5 Replies
View Related
Aug 22, 2011
I've been searching how to make my E3000 use the DHCP and IP address on my primary router so I can share printers and computers on same gateway IP. I tried turning off DHCP on E3000, but not sure how to tell it to use the DHCP from the source "INTERNET"
View 1 Replies
View Related
Jan 29, 2011
When I click on "DHCP Reservation" button in the web interface of the E3000 I don't see any information about the current devices and the reservation list.This problem occurs when my sattelite reciever tries to get an IP address from the DHCP.the name of the receiver is "dream box" (no special characters).I didn't have any problem in the past with my previous router (3COM)Since there are error messages in the page (screenshot is attached), I've tried to use different browsers but the result was the same (Firefox, Safari, IE 8)
View 9 Replies
View Related
Feb 17, 2012
I updated to Firmware Version: 1.0.04. And now I can't logon to the router when my storage device is turned on. However, I can logon to the router when the device is off. If I turn the power on the storage device and try to navigate the router it says ".....Can't establish a connection to the server at 192.168.1.1." Then I have to reboot the router to be able to log back on.
View 3 Replies
View Related
Dec 31, 2012
Within the Internet Access Policy section of the browser based utility, is it possible to limit access for a specific device (PC) to LAN only (not allow any traffic to external internet)? I see that you can block internet access for a specific machine, however I didn't know if this was inclusive of LAN as well.If not, is there another way to achieve this via the E3000 or should I be looking for a solution on the specific PC itself?
View 4 Replies
View Related
Sep 7, 2010
Issue with Linksys E3000 router (firmware 1.0.02). I'm experiencing issues with the following wireless connections:
-iPhone 4G (wife's)
-iPod Touch 2G
-PC with wireless connection (non Linksys brand adapter)
-Acer NetBook (non Linksys brand adapter)
The issue is the connection gets interrupted and dropped, but the devices and the router DHCP clients table show the connections are still present. By interruption, I mean no data traffic is being transmitted.My wife's iPhone 4G and my son's iPod Touch wifi both show they are connected to the home network, complete with wifi bars being displayed, and the checkmark is present next to the home network connection in the the device settings for both. When I check the E3000 DHCP clients table, both Apple devices are listed as holding a connection. Yet both devices display network errors when trying to use any app that connects to the internet. By restarting the wifi connection on each, the connection is restored to the point where traffic now transmits. My wife and son estimate it is after about 10 minutes that they encounter the interruptions.
On the PC and NetBook, the connections have to be terminated and reconnected. I have not timed these to see how long before the connection becomes problematic.Interestingly, my ASUS laptop and my iPhone 4G do not have the issue, nor does my work laptop (Dell).There are no timeout parameters in the router config. Closest thing to it is the Beacon Interval, but I don't know which way to adjust it (up or down) to manage the devices that are experiencing interruptions. I have not made any interval adjustments...at this time, everything is set to default settings.This E3000 replaced an aging WRT54 (hardware v2) router so that I could have an N router in the house.
View 9 Replies
View Related
Feb 9, 2011
I just started having this problem yesterday. I was experiencing weird downloading/internet browsing issues and couldn't figure out what the problem was. I started looking around my router settings and noticed that in my DHCP Client list, my computer isn't in it. The router is hooked up to the computer, so it's not wireless. My phone and my girlfriend's laptop are listed, but the main computer isn't. It's especially causing problems with port forwarding. Downloads will stop because the port isn't showing as open. I'm running 64 bit Windows 7 and a Belkin N+ Wireless Router, model F5D8235-4.Firmware is up to date.
View 6 Replies
View Related
Jun 9, 2011
When I'm in Setup -> Basic Setup -> click on DHCP Reservation, I don't see all entries I've created earlier but computers that connect still have the correct IP address on the network; I don't know if I can create additional entries if nothing appears
When I go to Status -> Local Network -> DHCP Client Table the list is blank but some computers are connected to the networkI'm using firmware 1.0.01 build 10 Feb 21, 2011, language = English, Firefox 4.0.1.Rebooting the router doesn't change anything, I can't see connected LAN equipment and DHCP Reservation is empty despite the fact I've created entries.Together with the "Access Restriction" which doesn't allow to block a computer from 10pm => 8am unless you create 2 rules + various issues with attached USB + 2.4Ghz signal that is far from optimal (never able to achieve more than 144-N-Mbps) and I ask myself if I will not contact the store where I purchased this unit and ask a refund (and buy something else from another brand...)
View 9 Replies
View Related
Dec 19, 2011
I have replaced my main router WRT300N running dd-wrt with the a stock E4200 and an old WRT54G aslo running dd-wrt configured for wireless client bridge. Now that I'm learning more about 802.11N, I was wondering what client can I use to achieve 5ghz simultaneously radio transmission since my current setup cannot do this in the 5ghz band. Can the E3000 be ran in wireless client bridge mode, if not what product can provide this? On the other thought am I understanding MIMO?
Old setup: 802.11G 2.4ghz
WRT54G ))) ((( WRT300N ->ISP
Current Setup: 802.11N 2.4ghz MIMO?
WRT300N ))) ((( E4200 ->ISP
Wanted Setup: 802.11N 5ghz MIMO
( E4200 ->ISP)
View 3 Replies
View Related
Nov 16, 2011
I've got the E3000 set up and working. What I'd like to do now is monitor all the devices' connectivity to it. The bandwidth it consumes and stuff. Is there a way to do that on my router?
View 6 Replies
View Related
Jan 19, 2013
I have Linksys E3000 Router and it is connected to 7 Devices at this moment via DHCP. I have got New NAS Enclousre (8th Device) which has got Lan port . I have connected Box to One free Port on E3000 Router. I see DHCP Reservation from 192.168.0.1 assging one IP to My NAS Enclosure Box i.e 192.168.0.13 But when i ping that box . It's not pingable. When i try to browse that NAS Enclosure's setup web page - it's not opening. I can access that box setup page if i connect direct 1:1 Lan cable over private network (169.254.XXX). It means web server is runing on box. I am clueless. E3000 is assigning IP to NAS Enclosure but can't Browse or Ping. I tried to Assign Manual IP address to NAS enclusure and reconnect to router. Still I can't ping or browse.
#arp -a show that box has IP. (Output from MAC os) .
? (192.168.0.13) at (incomplete) on en0 ifscope [ethernet]
Ping test from Router Page.
PING 192.162.0.13 (192.162.0.13): 32 data bytes
40 bytes from 192.162.0.13: icmp_seq=0 ttl=46 time=286.6 ms
40 bytes from 192.162.0.13: icmp_seq=1 ttl=46 time=290.2 ms
[code]....
View 9 Replies
View Related
Apr 26, 2011
I just got a DIR-655 and set it all up pretty easily. I have 6 wired and 3 wireless. All work fine and all are set to use DHCP. But if I go (in the router) to the Lan Computers list under Device Info, three devices (2 wired, 1 wireless) do not appear. I do have a switch added to the system, but of the three devices connected to it, 1 shows in th Lan Computers list and the other 2 do not.Since everything works, I'm mostly just curious why this is. Every previous router I've had showed everything correctly.
View 3 Replies
View Related
