Linksys Wireless Router :: EA4500 DHCP Client Table Erased?

Aug 22, 2012

My EA4500 will periodically clear out the DHCP Client Table and I will lose internet access.This happens once almost every day, normally in the morning. If I can't access the internet I will check the DHCP client table under Status -> Local Network -> DHCP Client Table and it is always empty.After I select Setup -> Reboot it will work again - when I look at the DHCP client table it is now populated with all my devices. I am on firmware version 2.0.37.

View 3 Replies


ADVERTISEMENT

Linksys Wireless Router :: DHCP Client Table Not Accurate (EA4500)

Jun 5, 2012

I have DHCP enabled, but I have assigned a static IP to most of my network devices.When I click on the DHCP Client Table, most of the devices are NOT shown even though I know they are connected and working.One device (a Brother printer) that I have assigned a static IP to actually shows up as having an IP from the DHCP range. A Panasonic TV does not show up at all even though it is connected and woking.  I have not been able to assign a static IP to it because it does not show up.

View 3 Replies View Related

Linksys Wireless Router :: EA3500 - Refresh DHCP Client Table?

Jun 2, 2012

I just got an EA3500 and I guess I don't understand what "Refresh" does when viewing the DHCP client table under the "Status", "Local Network" tab of the web interface, either that or it's not working.  If I have active wired and wireless clients and I power off the EA3500, wait a few minutes, then power it back on, the table is blank.  If I hit "Refresh" I would expect it to re-populate the table with the connected clients.  For whatever reason, it doesn't.  I have to physically disconnect and reconnect the E-net cable, or power cycle the wireless client to get them to reappear in the table.  Is something wrong with the router or its s/w

View 9 Replies View Related

Linksys Wireless Router :: No DHCP Client Table Showing In E4200?

Oct 29, 2011

I just purchased an E4200 router.  I have four clients on my network and they are all set up for DHCP.  I renewed their IPs and they all are connected.  "Cisco Connect" reports that I have four clients connected.  When I access the router and bring up the DHCP Client Table, there are no entries.  There should be four entries.  Aftern I enable the logging function, none of the logs have any data in them even after I wait for 45 minutes and use the internet and renew IPs.   I am using Firmware Version: 1.0.03.  I have the same results for both Chrome and Firefox. I want to be able to set Static IPs but I am hampered by the not having any clients in the DHCP client table.

View 9 Replies View Related

Linksys Wireless Router :: Ea3500 - Add Name To Few Ip Addresses In DHCP Client Table?

May 20, 2012

I'd like to add a name to a few ip addresses in the DHCP client table currently there is an asterix for a couple client names. the router is an ea3500. 

View 2 Replies View Related

Linksys Wireless Router :: BEFSX41 - Devices Missing In DHCP Client Table

Aug 7, 2006

I recently installed a WRT54G wireless router however I has this same question about my BEFSX41 Wired router.

View 9 Replies View Related

Linksys Wireless Router :: E3000 DHCP Client Table Not Showing Connected Device

Jan 10, 2011

I upgraded to firmware version 1.0.03 I started to have this weird issue: I have four PCs connected to this wireless router via wireless G. They all run Windows 7 Home Premium. After a few hours I started to notice that the DHCP client table is empty even if all four PCs are connected to the internet. This causes a networking problem because one of the PC serves as a file server and it grants access by IP addresses. Not being able to "see" those computers, my access is denied.

View 2 Replies View Related

Linksys Wired Router :: BEFSR41 DHCP Client Table Corruption?

Jan 31, 2011

Most devices pass a client name to DHCP when requesting an IP, but some like my smartphone, do not. When a device does not pass a client name garbage is entered as the name of the client name.The first is that when you use the Web Admin pages, and select Status/Local Network/DHCP Clients, the table will not display any clients because there is an error on the page. If you right click and View Source from the browser, you will see all the client entries are there and one of them will have garbage (unprintable characters) for the client name.The second and more serious issue is that the internal DHCP table once corrupt is unstable. I've had my BEFSR41 reboot because of the corruption and then I get IP conflicts on my LAN because the DHCP starts handing out in-use IPs.I'm on hardware version 4.3 and the latest firmware Ver.2.00.4 Build 8 (which is very difficult to install without bricking the router). BTW, when I use a WRT54GL router with the smartphone, it is properly handled by the DHCP and shows a blank client name, not garbage.

View 3 Replies View Related

Linksys Cable / DSL :: X2000 DHCP Client Table Failed To Show Client List

Apr 21, 2013

Do the problem caused by the modems itself or it just sign of faulty Ethernet switch (using 20 port Allied Telesis ethernet switch).
Sometimes I cannot connect to internet due to "unidentified network" buy i can resolve this problem by restarting my modem + switch.

View 4 Replies View Related

Cisco WAN :: Does 891 Router Have DHCP Client Table GUI?

Jun 21, 2011

how I can get to  the DHCP client table on a Cisco 891 Router ? We just upgraded our router from a WRVS4400N to the Cisco 891. THe WRVS4400N has the feature DHCP client table that I can see the Client host Name and IP address,Mac Address I have CCP and CCP express installed on my system?

View 1 Replies View Related

Linksys Wireless Router :: EA4500 From About 5 To 10 Minutes Later Internet Freezes On Table

May 2, 2012

I was using the Sony Tablet with an earlier version of a linksys modem and everything worked fine. Since changing to the 4500 I have access to the network have full internet service and the anywhere from about 5 to 10 minutes later the internet freezes on the table and I have to reboot connection and the its fine for about another 5 to 10 minutes before it freezes again.

View 6 Replies View Related

Linksys Wireless Router :: E2500v2 DHCP Reservation Table Bug

May 12, 2013

I tried to enter a name that included an illegal character (in this case, a single quote), and it gave me the popup box that said I had done so. When the popup closed, my DHCP reservation table was emptied out (I had maybe 5-6 reserved clients). In fact, I can't add new reservations anymore at all from this screen as it lists nothing in the DHCP clients table at the top. (Note, there are plenty of things in the DHCP Clients table over on the Status->Local Network tab). At this point, I think that my pre-existing reservations are still being held, but I'm not sure as it's only been about an hour so nothing has renewed.
 
I had firmware 1.0.05 when I encountered this problem. I upgraded to 1.0.07 as a means of trying to kick it into action, but the problem still exists. 

View 1 Replies View Related

Linksys Wireless Router :: E3200 - DHCP Reservation Table Is Incomplete?

Sep 24, 2011

my researvation table is incomplete. Below I show ipconfig that shows wired & wireless NICs assigned ip addresses by the E3200 router but the DHCP table only shows one.
 
I need to reserve the ip address of the wired address but can't get at it.

View 2 Replies View Related

Linksys Wireless Router :: E3200 Clears DHCP Table Randomly

Jan 29, 2012

My E3200 has been clearing it's DHCP table at random times. When it's been cleared the router starts handing out duplicate addresses. It's running the latest (1.0.02 build 9 Sep 1, 2011) firmware and otherwise seems to be working fine.

View 9 Replies View Related

Linksys Wireless Router :: E4200 - Media Bridges Can't Show Up In DHCP Table

Jan 11, 2012

I have 2 Media Bridges, a Trendnet  TEW-640MB and TrendNet TEW-680MB.  Both are set as a Static IP on the devices 192.168.1.150 and 192.168.1.151.   In the DHCP table for my E4200 I don't see those.  I have no problem accessing them typing in those IP addresses but wondering why they don't show up in the table.Actually looking at it more closely, the devices hooked up that are active seem to show up.So I see the following below.  And where is list LAN but no name those seem to be devices connected to the media bridges.
 
 LAN192.168.1.128    LAN192.168.1.129   iPhoneWireless192.168.1.130 1  Wireless192.168.1.131    LAN192.168.1.135   

View 2 Replies View Related

Linksys Wireless Router :: WRT54GL - DHCP Active IP Table Don't Show Wired One?

Oct 14, 2012

On my old Linksys WRT54GL router (with its latest stock firmware)'s http://192.168.1.1/DHCPTable.asp for DHCP Active IP Table, it only shows wireless connections. How come it doesn't show wired ones?

View 5 Replies View Related

Linksys Wireless Router :: E4200 DCHP Client Table Doesn't Reset After Soft Reboot

Jul 15, 2011

One of the many things that I liked about the e4200 over my olg 54GL was the fact that I could reboot it remotely.   However, I've recently had a few problems that only a full power down would fix.   In addition, I've noticed that the DCHP client table doesn't reset when I do a soft reboot.   Is this intentional?   Is the soft reboot not really a full reboot? Can it be made a real reboot?

View 7 Replies View Related

Linksys Wired Router :: BEFVP41 / DHCP - Set Static Table IPs For Security Camera DVR?

Jun 22, 2011

I have enabled DHCP but want to set static table IP's for my security camera DVR and one computer, the others can remain dynamic. I know in other routers I can attach a LAN IP to a mac address to keep it static but I can't see where I can do that with this router.

View 4 Replies View Related

Linksys Wireless Router :: DHCP Client In E4200 Becoming Unreliable

Mar 20, 2013

I have ten E4200 routers deployed in five library branches.  In recent months, the E4200's in two branches have occasionally gone into a state where they are not always providing an IP address to both wired and wireless devices.  Some devices will get an IP fine and others will not,  The problem seems to move and the next day the same device will connect fine and others will not.  A reset of the router usually clears the problem but it is becoming more frequent and bothersome.  For some reason only two locations are effected.
 
Some notes:
 
- Firmware version is 1.0.02 build 13

- When I set devices up with static IP's they work fine, so the problem seems to be related to the DHCP service

- The WAN side of the network tests fine with no issues

- I've had these routers deployed for over a year and this problem just started in the past two months

- Routers and AP's are on different channels to prevent interference

- No nearby WiFi signals appear to be casuing any interference

View 3 Replies View Related

Linksys Wireless Router :: E2500 DHCP Client List Not Showing

Aug 25, 2011

I have purchased E2500 and i am having following problems:
 
1. DHCP client list not showing - only shows when i reboot the router. After some time, the list never shows even when i press refresh button
2. I can only reserve IP when i reboot the router - after some time i cannot do this action also
 
I have upgraded to latest firmware and also peformed reset as directed by support.

View 1 Replies View Related

Linksys Wireless Router :: WRT310N V1 DHCP Client Fails To Renew Lease

Apr 28, 2013

I have a Linksys WRT310N v1 with firmware v1.0.10 build 002Jul 19, 2010 My router fails to renew it's DHCP lease from my cable provider, causing internet access to drop. I can still access my cable modem at 192.168.100.1, but I must do a "IP Address Release" then "IP Address Renew" to get back internet access. The router works fine otherwise.

View 6 Replies View Related

Linksys Wireless Router :: E4200 IPv6 Causes Win7 DHCP Client Crash?

Jun 9, 2012

When I enable IPv6 on my E4200, the Windows 7 DHCP client crashes. It also seems to crash the audio service, the event logger and a few other windows services.

View 9 Replies View Related

Linksys Wired Router :: BEFSR81 / Add Device Names To DHCP Device Table?

Nov 30, 2011

My BEFSR81 is my primary router and has DHCP turned on.  The router's DHCP range is set to accommodate 12 devices.  I have three computers wired to it and their Host names (as specified in the set-up of each computer) show up in the router's DHCP device table.  I also have two printers (one old Brother HL5250DN laser printer and one new HP Photosmart Premier C410a inkjet printer) connected and there are blanks where the Host name should go.  I would like to be able to tell which printer is which when I am looking at the DHCP device table.  How can I get a names associated with each printer's IP address in the router's DHCP device table?  (The real problem is that the router seems to have both printers at the same IP address (192.168.1.100) and if I can get one of them to change I'd like to know which one it was!)

View 1 Replies View Related

Linksys Wireless Router :: EA6500 - Change DHCP Client Lease Time From 1440 To 480 Minutes

Apr 2, 2013

I'm trying to change the DHCP Client Lease Time from 1440 minutes to 480 minutes.  When I try to apply the new settings, I'm getting a message that says "Invalid Characters" and it won't stick. I've tried this in three different up-to-date browsers (ie10, Chrome and Firefox).  Also, I'm connecting locally through LAN and I have the latest EA6500 Firmware: 2.1.39.145204

View 2 Replies View Related

Linksys Wired Router :: WRT54G Maximum Value For DHCP Client Lease Time?

Jun 26, 2011

On the BEFSR41 v1 series and WRT54G series, what is the maximum value for the DHCP "Client Lease Time (in minutes)?"  It seems that 2^16 -1 (65535) minutes is the max.  This is about 45 days.  has the max value changed with newer versions  of these devices?

View 1 Replies View Related

Cisco WAN :: Save DHCP Table Inside Of External Flash In 2801 Router

Dec 3, 2012

how to storage the DHCP IP table in a external flash of a router. This is because the router is switched off and switched on everyday but I want that it remembers which MAC is associated with which IP when it starts again and avoid IP duplicate problems. The command "lease" doesn't seem useful here.

View 4 Replies View Related

TP-Link ADSL2+ Wireless :: W8961ND - DHCP Table Is Full

Nov 15, 2012

Region : Thailand
Model : TD-W8961ND
Hardware Version : V1
Firmware Version : 2.0.0 Build 111111 Rel.1111
ISP : 3bb

I have a problem when I am trying to add another static ip address to the list

the message above in title pop up, how can I fix it?

DHCP Table is Full!

View 1 Replies View Related

Linksys Wireless Router :: WRTP54G Restarting / MAC Filter Table?

Mar 14, 2012

Two issues with WRTP54G
 
1.)  when making changes and restarting the router I am unable to get web pages (wired port or wireless) or web response from the router, despite re-entering the URL (192.xxx.x.x).  I *DO* get a dialtone (VoIP).  To get router restarted I have to get my lazy arse up and cycle power to the router.  Like I said, a nuisance.Configured for WPA2 Personal security with MAC Wireless Filtering (9 MACs)
 
2.)  Adding a 10th wireless device to the filter table and the MAC 10: becomes duplicated in MAC 09: while the existing MAC 09: disappears.  Finally got it to accept my new device but now I have 2 devices repeated in the MAC Filter Table.  Not a clean setup.

View 1 Replies View Related

Linksys Wireless Router :: WRTP54G Route Table - Broken Internet Access

May 2, 2011

I know that WRTP54G is a voip device, but it is router as well and my problem is related to routing part.I cannot access public internet servers with IP in subnet 2.0.0.0 / 8 and 1.0.0.0 / 8. In the 2.0.0.0 / 8 subnet are some akamai cdn servers (yes, the fbcdn .After some time I've found, that routing table in wrtp54g contains also entries:
 
1.0.0.0                 0.0.0.0                 255.0.0.0                 LAN&Wireless2.0.0.0                 0.0.0.0                 255.0.0.0                 LAN&Wireless

which cannot be deleted. It looks like someone wanted to filter dark space when the router was developed.Is there any way, to get rid of it? I've restored to factory defaults, no change. Firmware version is 3.1.27.ETSI

View 9 Replies View Related

How To Retrieve Accidentally Erased Emails

Mar 27, 2011

Yesterday on 26 march all of a sudden my 2250 emails from hotmail@live.com was erased.I donot know why or how.I have always have problem.So many times my emails have been erased.

View 2 Replies View Related

Cisco Switching/Routing :: Nexus 7000 - Ip Dhcp Snooping Binding Table Is Empty?

Sep 14, 2010

I've configured ip dhcp snooping on several vlans I want to monitor and the binding table doesn't seem to be building.eature DHCP is on, global ip dhcp snooping is enabled, VLAN snooping is enabled on the vlan's I want to monitor and my trusted interfaces are also configured. Alas no binding entries in the table! 7K is running 4.2(6).

View 1 Replies View Related

Linksys Wireless Router :: Set Up EA4500 Without A Computer?

Sep 2, 2012

I've looked all over the internet for this and can't find a definate answer. Waited for live chat and got kicked before I got to talk to someone... Just sold my computer and the plan was to buy a newer mac but we've been getting along fine without a computer with just using our iphones. So my question, I see that Cisco has the Connect Express app for the iphone, and I've read about all the features it has like changing settings, router features, etc. But I can't find anything on using the app for the initial set up of the router. I'm currently on an older linksys router (set up before we sold the computer) but it's time for a needed upgrade.

View 3 Replies View Related

Linksys Wireless Router :: Using An External HDD For EA4500?

Apr 30, 2012

I got my ea4500 all set up. never had a media servor or anything like that, figured this would be an easier way. when i hook up my exteral i can find it but i can only view the files in windows media player. how can i just browse the folders manually? WMP doesnt let me browse the folders as they actually are on the HDD which is such a pain in the **bleep**. 
 
shows a device in "network infrastructure" but it says problem sending command to the program when i click that. i dont want to have to view the HDD in WMP as a media device...

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved