Linksys Wireless Router :: No DHCP Client Table Showing In E4200?
Oct 29, 2011
I just purchased an E4200 router. I have four clients on my network and they are all set up for DHCP. I renewed their IPs and they all are connected. "Cisco Connect" reports that I have four clients connected. When I access the router and bring up the DHCP Client Table, there are no entries. There should be four entries. Aftern I enable the logging function, none of the logs have any data in them even after I wait for 45 minutes and use the internet and renew IPs. I am using Firmware Version: 1.0.03. I have the same results for both Chrome and Firefox. I want to be able to set Static IPs but I am hampered by the not having any clients in the DHCP client table.
View 9 Replies
ADVERTISEMENT
Jan 10, 2011
I upgraded to firmware version 1.0.03 I started to have this weird issue: I have four PCs connected to this wireless router via wireless G. They all run Windows 7 Home Premium. After a few hours I started to notice that the DHCP client table is empty even if all four PCs are connected to the internet. This causes a networking problem because one of the PC serves as a file server and it grants access by IP addresses. Not being able to "see" those computers, my access is denied.
View 2 Replies
View Related
Jun 2, 2012
I just got an EA3500 and I guess I don't understand what "Refresh" does when viewing the DHCP client table under the "Status", "Local Network" tab of the web interface, either that or it's not working. If I have active wired and wireless clients and I power off the EA3500, wait a few minutes, then power it back on, the table is blank. If I hit "Refresh" I would expect it to re-populate the table with the connected clients. For whatever reason, it doesn't. I have to physically disconnect and reconnect the E-net cable, or power cycle the wireless client to get them to reappear in the table. Is something wrong with the router or its s/w
View 9 Replies
View Related
Aug 22, 2012
My EA4500 will periodically clear out the DHCP Client Table and I will lose internet access.This happens once almost every day, normally in the morning. If I can't access the internet I will check the DHCP client table under Status -> Local Network -> DHCP Client Table and it is always empty.After I select Setup -> Reboot it will work again - when I look at the DHCP client table it is now populated with all my devices. I am on firmware version 2.0.37.
View 3 Replies
View Related
May 20, 2012
I'd like to add a name to a few ip addresses in the DHCP client table currently there is an asterix for a couple client names. the router is an ea3500.
View 2 Replies
View Related
Jun 5, 2012
I have DHCP enabled, but I have assigned a static IP to most of my network devices.When I click on the DHCP Client Table, most of the devices are NOT shown even though I know they are connected and working.One device (a Brother printer) that I have assigned a static IP to actually shows up as having an IP from the DHCP range. A Panasonic TV does not show up at all even though it is connected and woking. I have not been able to assign a static IP to it because it does not show up.
View 3 Replies
View Related
Jan 11, 2012
I have 2 Media Bridges, a Trendnet TEW-640MB and TrendNet TEW-680MB. Both are set as a Static IP on the devices 192.168.1.150 and 192.168.1.151. In the DHCP table for my E4200 I don't see those. I have no problem accessing them typing in those IP addresses but wondering why they don't show up in the table.Actually looking at it more closely, the devices hooked up that are active seem to show up.So I see the following below. And where is list LAN but no name those seem to be devices connected to the media bridges.
LAN192.168.1.128 LAN192.168.1.129 iPhoneWireless192.168.1.130 1 Wireless192.168.1.131 LAN192.168.1.135
View 2 Replies
View Related
Aug 7, 2006
I recently installed a WRT54G wireless router however I has this same question about my BEFSX41 Wired router.
View 9 Replies
View Related
Jul 15, 2011
One of the many things that I liked about the e4200 over my olg 54GL was the fact that I could reboot it remotely. However, I've recently had a few problems that only a full power down would fix. In addition, I've noticed that the DCHP client table doesn't reset when I do a soft reboot. Is this intentional? Is the soft reboot not really a full reboot? Can it be made a real reboot?
View 7 Replies
View Related
Jun 9, 2011
When I'm in Setup -> Basic Setup -> click on DHCP Reservation, I don't see all entries I've created earlier but computers that connect still have the correct IP address on the network; I don't know if I can create additional entries if nothing appears
When I go to Status -> Local Network -> DHCP Client Table the list is blank but some computers are connected to the networkI'm using firmware 1.0.01 build 10 Feb 21, 2011, language = English, Firefox 4.0.1.Rebooting the router doesn't change anything, I can't see connected LAN equipment and DHCP Reservation is empty despite the fact I've created entries.Together with the "Access Restriction" which doesn't allow to block a computer from 10pm => 8am unless you create 2 rules + various issues with attached USB + 2.4Ghz signal that is far from optimal (never able to achieve more than 144-N-Mbps) and I ask myself if I will not contact the store where I purchased this unit and ask a refund (and buy something else from another brand...)
View 9 Replies
View Related
Aug 25, 2011
I have purchased E2500 and i am having following problems:
1. DHCP client list not showing - only shows when i reboot the router. After some time, the list never shows even when i press refresh button
2. I can only reserve IP when i reboot the router - after some time i cannot do this action also
I have upgraded to latest firmware and also peformed reset as directed by support.
View 1 Replies
View Related
Jan 31, 2011
Most devices pass a client name to DHCP when requesting an IP, but some like my smartphone, do not. When a device does not pass a client name garbage is entered as the name of the client name.The first is that when you use the Web Admin pages, and select Status/Local Network/DHCP Clients, the table will not display any clients because there is an error on the page. If you right click and View Source from the browser, you will see all the client entries are there and one of them will have garbage (unprintable characters) for the client name.The second and more serious issue is that the internal DHCP table once corrupt is unstable. I've had my BEFSR41 reboot because of the corruption and then I get IP conflicts on my LAN because the DHCP starts handing out in-use IPs.I'm on hardware version 4.3 and the latest firmware Ver.2.00.4 Build 8 (which is very difficult to install without bricking the router). BTW, when I use a WRT54GL router with the smartphone, it is properly handled by the DHCP and shows a blank client name, not garbage.
View 3 Replies
View Related
Apr 21, 2013
Do the problem caused by the modems itself or it just sign of faulty Ethernet switch (using 20 port Allied Telesis ethernet switch).
Sometimes I cannot connect to internet due to "unidentified network" buy i can resolve this problem by restarting my modem + switch.
View 4 Replies
View Related
Mar 20, 2013
I have ten E4200 routers deployed in five library branches. In recent months, the E4200's in two branches have occasionally gone into a state where they are not always providing an IP address to both wired and wireless devices. Some devices will get an IP fine and others will not, The problem seems to move and the next day the same device will connect fine and others will not. A reset of the router usually clears the problem but it is becoming more frequent and bothersome. For some reason only two locations are effected.
Some notes:
- Firmware version is 1.0.02 build 13
- When I set devices up with static IP's they work fine, so the problem seems to be related to the DHCP service
- The WAN side of the network tests fine with no issues
- I've had these routers deployed for over a year and this problem just started in the past two months
- Routers and AP's are on different channels to prevent interference
- No nearby WiFi signals appear to be casuing any interference
View 3 Replies
View Related
Jun 9, 2012
When I enable IPv6 on my E4200, the Windows 7 DHCP client crashes. It also seems to crash the audio service, the event logger and a few other windows services.
View 9 Replies
View Related
Jun 21, 2011
how I can get to the DHCP client table on a Cisco 891 Router ? We just upgraded our router from a WRVS4400N to the Cisco 891. THe WRVS4400N has the feature DHCP client table that I can see the Client host Name and IP address,Mac Address I have CCP and CCP express installed on my system?
View 1 Replies
View Related
May 12, 2013
I tried to enter a name that included an illegal character (in this case, a single quote), and it gave me the popup box that said I had done so. When the popup closed, my DHCP reservation table was emptied out (I had maybe 5-6 reserved clients). In fact, I can't add new reservations anymore at all from this screen as it lists nothing in the DHCP clients table at the top. (Note, there are plenty of things in the DHCP Clients table over on the Status->Local Network tab). At this point, I think that my pre-existing reservations are still being held, but I'm not sure as it's only been about an hour so nothing has renewed.
I had firmware 1.0.05 when I encountered this problem. I upgraded to 1.0.07 as a means of trying to kick it into action, but the problem still exists.
View 1 Replies
View Related
Sep 24, 2011
my researvation table is incomplete. Below I show ipconfig that shows wired & wireless NICs assigned ip addresses by the E3200 router but the DHCP table only shows one.
I need to reserve the ip address of the wired address but can't get at it.
View 2 Replies
View Related
Jan 29, 2012
My E3200 has been clearing it's DHCP table at random times. When it's been cleared the router starts handing out duplicate addresses. It's running the latest (1.0.02 build 9 Sep 1, 2011) firmware and otherwise seems to be working fine.
View 9 Replies
View Related
Oct 14, 2012
On my old Linksys WRT54GL router (with its latest stock firmware)'s http://192.168.1.1/DHCPTable.asp for DHCP Active IP Table, it only shows wireless connections. How come it doesn't show wired ones?
View 5 Replies
View Related
Mar 13, 2012
My router usb storege was working fine with my old videos and streaming fine too but now im putting some new videos on the usb storage my router its not showing the new videos on the usb storage.
View 2 Replies
View Related
Oct 19, 2011
Just got my E4200, setup and working with my laptop, But its only showing a speed of 65Mbps, How to get it up to the advertised 300Mbps?
View 6 Replies
View Related
Feb 9, 2011
I just started having this problem yesterday. I was experiencing weird downloading/internet browsing issues and couldn't figure out what the problem was. I started looking around my router settings and noticed that in my DHCP Client list, my computer isn't in it. The router is hooked up to the computer, so it's not wireless. My phone and my girlfriend's laptop are listed, but the main computer isn't. It's especially causing problems with port forwarding. Downloads will stop because the port isn't showing as open. I'm running 64 bit Windows 7 and a Belkin N+ Wireless Router, model F5D8235-4.Firmware is up to date.
View 6 Replies
View Related
May 2, 2013
I have the WRT400N router with the latest firmware. Recently I have noticed a device in my DHCP that I do not recognize. It is not device I own (believe me, I have racked my brain and confirmed) as it shows as an Acer pc. I cannot ping the IP address however. I have rebooted my router several times thinking maybe it's a former connected device but saved in memory but it keeps coming back. I am thinking possibly it is someone hi-jacking my Internet, but not sure. I am using WEP security but it shows a LAN connection which is strange for a wireless device. The only hard wired pc is my HP.
View 3 Replies
View Related
Apr 8, 2012
I am experiencing connectivity issues with the wireless part for several weeks. The laptop connects to it, but it shows me that it does not have internet access.I also have a belkin router that I also use. So, when I have the connectivity issues, I connect to the other router. When I use the Cisco Connect application, it goes on for a couple of minutes and then gives the message "If you are not connected to my router SSID name you can't update your router settings".
View 1 Replies
View Related
Feb 23, 2013
I have a Wireless N router model F5D8236-4 v2 (01) with firmware 2.00.04 (Nov 12 2008 10:51:08) and it's not showing all issued wireless or Wired IP addresses in DHCP Client List.
They all have IP addresses and connect to the internet through the router, but in the router administration page, they're not listing. The Windows devices all show but most of the Mac devices are not, nor is my XBox 360.
My reason for investigating this is because the router seems to keep losing the Mac devices and a router reboot fixes it, but it shouldn't have this problem because all the Windows devices just seem to work.
According to the support page I have the latest available (dated November 12, 2008 which really seems kinda old to me for a Wireless N router). Are there any plans for a new firmware offering for this modem or have you already deprecated it as "legacy equipment"?
View 1 Replies
View Related
Jun 22, 2011
I have enabled DHCP but want to set static table IP's for my security camera DVR and one computer, the others can remain dynamic. I know in other routers I can attach a LAN IP to a mac address to keep it static but I can't see where I can do that with this router.
View 4 Replies
View Related
Mar 19, 2012
I have an e4200 set up and working on fios as a pppoe router properly with a dozen devices connected to it via dhcp. The dhcp range i configured in the e4200 is 192.168.1 100 to start with, and a mask of 255.255.255.0.
All the dhcp devices connected to the router start with 192.168.1.1xx. My Dell Inspirion with Windows 7 has an ipv4 address of 192.168.15.2. I cannot figure out how it gets this address, even after I release and renew the address on the Dell.
Everything is working fine so I guess there is something I just do not understand.
View 3 Replies
View Related
Mar 10, 2012
I've assigned an ip address to my htpc using dhcp reservation. On my old router I could use the client name, for instance: ssh name@clientName Instead of: ssh name@ipAddress Currently I cannot do this with the stock cisco firmware (unless I'm mistaken). Is there something I have to do to get it working? Or do I have to resort to tomatoUSB/WRT.
View 1 Replies
View Related
Dec 4, 2011
The e4200 1.0.03 DHCP server appears to be quite buggy. After configuring a static IP / reservation for a client which already had a dynamic IP from the pool, the e4200 continued to offer this client its pool IP. However, the DHCP client listing in the e4200 showed the client having the static IP even though it was still being offered that pool address.This may sound like user error, but I can assure you, it is not. I have had a very frustrating experience with this product, and rather than fool with tech support again, I ran `tcpdump -e -s1600 -n -vvvv -i eth0 port bootpc or port bootps` to absolutely rule out a mistake on my part, bug in the DHCP client, etc. I found that the client was always offered that old IP, even thought the e4200 status display showed the "new" static one, after doing a DHCPDISCOVER without requesting a specific IP. This condition persists across e4200 reboots even after having the client release its lease!I finally was able to resolve this by forcing the client to request the static IP from the e4200.This is unquestionably a bug in the DHCP server, and additionally, the user interface does not show the real state of the underlying DHCP leases held by clients which have static addresses / reservations. Troubleshooting this condition is well beyond the abilities of the average user.
View 9 Replies
View Related
Dec 27, 2012
Is there a way to get the E4200 to NOT provide itself as a dns server to the DHCP clients? I have the unit set up to provide two dns servers to the clients, but the 4200 always provides itself as a third and it uses my cable providers dns servers. I am using a dns based filtering service to prevent certain material from being accessed within my network as the first two resolvers. So long as both or one of the provided servers is working it doesn't fall back to the unfiltered third, but I would prefer to remove it entirely.
View 8 Replies
View Related
Jan 4, 2012
I just bought a Linksys E4200v2 router and updated the firmware to 2.0.26.124551. The DHCP server is turned on however, it won't issue any IP addresses. I have to set IP reservations for all of my devices in order for the router to give them an IP address. This includes my printer, xbox360 and 2 computers. I'm also having this problem with the wired and wireless lan.
View 4 Replies
View Related
Jul 8, 2011
I just bought an e4200. I was using a LinkSys WRT54GS running DD-WRT alternative firmware.
One feature that I really liked in DD-WRT was the ability to assign static IP leases from the DHCP server. I liked having all of my devices running with a predictable, known IP address on my network. I have a Home Theater PC, and various controller applications that run on iPhones, etc. - some pretty homebrewed. Configuring the firewalls, etc. was much easier with IP address based controls.
Is there a way to achieve the same within the e4200's stock firmware?
View 1 Replies
View Related
