Computer Not Showing Up In DHCP Client List?
Feb 9, 2011
I just started having this problem yesterday. I was experiencing weird downloading/internet browsing issues and couldn't figure out what the problem was. I started looking around my router settings and noticed that in my DHCP Client list, my computer isn't in it. The router is hooked up to the computer, so it's not wireless. My phone and my girlfriend's laptop are listed, but the main computer isn't. It's especially causing problems with port forwarding. Downloads will stop because the port isn't showing as open. I'm running 64 bit Windows 7 and a Belkin N+ Wireless Router, model F5D8235-4.Firmware is up to date.
View 6 Replies
ADVERTISEMENT
Aug 25, 2011
I have purchased E2500 and i am having following problems:
1. DHCP client list not showing - only shows when i reboot the router. After some time, the list never shows even when i press refresh button
2. I can only reserve IP when i reboot the router - after some time i cannot do this action also
I have upgraded to latest firmware and also peformed reset as directed by support.
View 1 Replies
View Related
Feb 23, 2013
I have a Wireless N router model F5D8236-4 v2 (01) with firmware 2.00.04 (Nov 12 2008 10:51:08) and it's not showing all issued wireless or Wired IP addresses in DHCP Client List.
They all have IP addresses and connect to the internet through the router, but in the router administration page, they're not listing. The Windows devices all show but most of the Mac devices are not, nor is my XBox 360.
My reason for investigating this is because the router seems to keep losing the Mac devices and a router reboot fixes it, but it shouldn't have this problem because all the Windows devices just seem to work.
According to the support page I have the latest available (dated November 12, 2008 which really seems kinda old to me for a Wireless N router). Are there any plans for a new firmware offering for this modem or have you already deprecated it as "legacy equipment"?
View 1 Replies
View Related
Apr 21, 2013
Do the problem caused by the modems itself or it just sign of faulty Ethernet switch (using 20 port Allied Telesis ethernet switch).
Sometimes I cannot connect to internet due to "unidentified network" buy i can resolve this problem by restarting my modem + switch.
View 4 Replies
View Related
Nov 19, 2011
I keep getting some additional IP addresses logging onto my home network that have an address outside what should be allowed by the router. The server is running at 192.168.2.1 and is set to only allow clients from 192.168.2.2 - 192.168.2.10 so a total of 9 clients should be allowed on.The problem is that something keeps logging in with an address of 192.168.169.2 or 3 etc. Sometimes more than one device at a time.I have assumed that it is some automated or virtual client as I'm pretty certain my network has not been breached. I have a 9 character password with a relatively random alphanumeric combination, although I haven't tried changing the password (I live in a share house with with a bunch of devices using wireless, so I haven't yet bothered). What I don't understand is how it has connected with the xx.xx.169.xx range at all. I have a Belkin 'Share' Wireless N Modem Router and at some stage there was a 'guest' network but that has since been disabled and I still am seeing the extra address. I have attached a screen shot of the DHCP client list on the router.The following is a list of devices that may be on the network at times, I'm thinking one of these may be responsible for the problem:
Windows Vista Desktop - Only LAN device
PS3
Macbook
Epson wireless printer
Android HTC Desire Mobile Phone
Laptops running various Windows versions (XP, Vista and 7)
A few thoughts I had:
- the android phone is capable of running a wireless hotspot, may have to look into it to see if if has been operating as an access point into the Belkin router, but assumed this wouldn't bring up clients connected to the phone on the home router.
- The desktop has PS3 Media server installed to stream video to the PS3 over the network (not that I have ever managed to get it to work), however this is not ever open on the desktop.
View 10 Replies
View Related
Apr 19, 2011
i had the dir-655 with desktops and laptops running with xp and win 7, also some other devices such as ipod, iphone, ps3, xbox, problem occura with conflict of network ip address, i think xp and win 7 both login with the same network ip address. So I start to disconnect every device and try to connect each desktop and laptops, one by one, enabled the DHCP and reserve the network ip to avoid conflict. But here's the problem, when I connect the first computer with wired to the dir-655, can't find the computer in the DHCP list so I cannot do the reserve, I'm able to surf internet even I can see info with ipconfig. So I connected 1 wired and 2 wifi to the network, only 1 wifi network ip showing on the list, so I reserve that one, but after I refresh, the DHCP list is empty.
View 1 Replies
View Related
Dec 3, 2012
Region : France
Model : TD-W8968
Hardware Version : V1
Firmware Version : TD-W8968_V1_120926
ISP : SFR
Device in question: siemans C610 IP voip phone
Configuration:
* The C610 is directly connected to TD W8968 via the ethernet port number 3 >> ethernet port number 1 is connected to the devolo homeplug 200AVPLUS . The PC is at the other end of the homeplug network
* The DHCP address starts at 192.168.1.100 - 192.168.1.199.
Symptom:
1. It takes a long time (about 2-3 minutes) for the C610IP to obtain the IP address of 192.168.1.100 after the synchronisation of the ADSL line is finished 2. In the DHCP client list, I could only see the IP address of the PC (192.168.1.101) but not the C610 IP. However, if I type 192.168.1.100, I could access to the configuration page of the C610 IP. - I only managed to see the C610IP once in the DHCP client list.
I tried to unplug -> replug the router but to no avail.
View 2 Replies
View Related
Dec 6, 2012
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
ISP : Comcast
So I've been checking my router DHCP list and I usually use the WPS feature to add devices. I know how many devices I have and which ones are wireless etc. I've made address reservations on all the devices that I have and know of. One feature that really frustrates me (which is missing) is no way to rename a device. My iPhone is named: Reggie's iPhone yet the 4300 picks it up as Unknown... I dont understand why. I've renamed it on the iPhone to different things and restarted it but still it comes up as that. I have 2 Nexus 7s and both come up with wierd names, one is for my wife and one is for me and I wish there was a way to name it proper.
Question is: Will the name edit feature ever get added to it? I dont get why it's not there now, it's not really something major (I have a 5 year old router that even has that... and it cant even support N). It's really frustrating to have to guess and check the devices on my network because most of them come up as unknowns.
Right now I'm trying to located another device that's coming up as unknown and now matter how much I try, since the router lacks any feature to assist finding it, it's really frustrating.
something else i noticed: my DHCP List shows all the devices connected with their IP addresses, yet I went into CMD and was doing a random ping command. I'm able to ping 192.168.0.114 with perfect stats back yet on my DHCP List it shows the highest IP is at 192.168.0.112.... Is something wrong here? Is it supposed to not pick up the IPs it gives out? And of course since there isnt a way to tell if that IP is for a WIFI or ethernet device, I have no idea what that device is...
yet i found another ip address on my network by using the ping command. actually I went ahead and did arp -a to find out all the ips with mac addresses. this is a serious flaw with the security of this router!!
View 2 Replies
View Related
Oct 29, 2011
I just purchased an E4200 router. I have four clients on my network and they are all set up for DHCP. I renewed their IPs and they all are connected. "Cisco Connect" reports that I have four clients connected. When I access the router and bring up the DHCP Client Table, there are no entries. There should be four entries. Aftern I enable the logging function, none of the logs have any data in them even after I wait for 45 minutes and use the internet and renew IPs. I am using Firmware Version: 1.0.03. I have the same results for both Chrome and Firefox. I want to be able to set Static IPs but I am hampered by the not having any clients in the DHCP client table.
View 9 Replies
View Related
Jan 10, 2011
I upgraded to firmware version 1.0.03 I started to have this weird issue: I have four PCs connected to this wireless router via wireless G. They all run Windows 7 Home Premium. After a few hours I started to notice that the DHCP client table is empty even if all four PCs are connected to the internet. This causes a networking problem because one of the PC serves as a file server and it grants access by IP addresses. Not being able to "see" those computers, my access is denied.
View 2 Replies
View Related
Jan 25, 2011
I have problems with my D-Link DIR 635 router. It shows up fine in list of networks on my girlfriends Mac and on my new laptop, but on my older laptop it doesnt show up at all (whereas a lot of other networks do). Seeing as my current laptop is being repaired at the moment, I need to be able to connect to the net with my old laptop too.
I run Windows XP Professional on my laptop, which is a Compaq Presario f700. why the network doesnt show up?
View 3 Replies
View Related
Nov 17, 2011
When I'm home I can get online but it's slow webstar. I used to be able to get online at the local McDonalds with free wi-fi, real fast. Now, the connection list doesn't show the "FREE McDonalds" connection.
I have: Atheros AR5B97 Wireless Network Adapter, Windows 7 on ACER Aspire 7741z-4815. It has been updating until recently, don't know if it's because I haven't been online as often or what.
View 1 Replies
View Related
Nov 27, 2012
I have an EA4500 and am using Cisco Connect Cloud software. Its working mostly fine except that I have one device on the network that will not show up in the device list. This is not an issue in itself and normally I would ignore (although it used to show up when I forst got the router) however..
The device is a WDTVLive media unit and required access to windows shares on a media server. Now the WDTVLive device is server an ip address by the router and is available from everywhere on my network but every couple of days it loses the capacity to search windows shares.
I know what you are thinking and I initially thought the same, this is an issue with the WDTVLive box. However one day I spent a few hours trying to resolve (Am an IT Consultant and know a little about networks) and found that I could not fix the issue. I then rebooted the router and it started working. I have since confirmed that every time it breaks I have to reboot the router.
View 7 Replies
View Related
Dec 18, 2012
Why is my WRT54g router only showing the 1st LED port is lit, and not the rest when I have changed or added a device to the 2nd,3rd,4th port? It is also stopping my ability to stream,view youtube etc. When I disconnect the router from my cable provided modem, everything works fine?
View 2 Replies
View Related
Apr 26, 2011
I just got a DIR-655 and set it all up pretty easily. I have 6 wired and 3 wireless. All work fine and all are set to use DHCP. But if I go (in the router) to the Lan Computers list under Device Info, three devices (2 wired, 1 wireless) do not appear. I do have a switch added to the system, but of the three devices connected to it, 1 shows in th Lan Computers list and the other 2 do not.Since everything works, I'm mostly just curious why this is. Every previous router I've had showed everything correctly.
View 3 Replies
View Related
Feb 8, 2011
Is there any way to clear the archived DHCP list on the Belkin F5D7230-4 wireless router? Over the years there have been a lot of connections, most are no longer around but the Belkin holds on to the list. I can find no way to clear it to get it back to what is currently connected. I have tried a soft reboot, unplugging power etc but it seems like I will have to do a factory reset and apart from not being able to find my ADSL login details, I would have to reset all my settings.
View 2 Replies
View Related
Nov 23, 2010
Why is the DHCP Reservations List limited to 25 entries? Is there a beta firmware version that allows more?
View 5 Replies
View Related
Jan 2, 2012
I have a DIR-615 router running FW version 3.01 with Hardware Version: C1 , my xbox is wired to my router. When I port forwarded, i had an strict nat, but had the best connection, but not by very much. When i put DMZ on, i had a strict nat, and the connection to other people was a bit better then UPnP.When i had UPnP on i had a open nat, i could barely be able to connect to anyone.what is a DHCP Reservations List?
View 3 Replies
View Related
Mar 5, 2012
Ever since I updated my firmware to 1.01 my web interface for the network settings screen has been random. Somtimes it shows a DHCP reservation list, sometimes it doesn't. Sometimes there are reservations, sometimes there are selectable radio buttons. I guess I'm just trying to figure out if this is a firmware issue or not. Ever since I updated the firmware it has been flakey.... But I was having issues with other stuff before that. When there are no reservations, sometimes i can't even select any computers because there aren't any in the drop down, when all of my hardware is online?
View 6 Replies
View Related
Jan 13, 2010
I have a setup using LogMeIn Hamachi and the network type creates a Windows Bridge. I also use the DHCP Reservations List to assign the same IP to specific devices. Well I have the MAC Address for my NIC in the list which works when I am not using the bridge. When using the bridge, of course the MAC address changes and when I try to add it to the list I get the following message in a popup window. The MAC Address is 02:e0:61:05:45:3e I have tried manually entering it, letting the router enter it from the list of computers and just to rule out something stupid, I have tried changing the letters to upper case and removing the colons.
Another issue I can see when this issue is resolved is that I do not believe it will let me add this reservation since I will be using the same IP used by another reservation. My DGL-4500 allowed this if I had the other reservations using the same IP disabled.Below these comments/rants are some feature requests. I have put them last as some of the requests are explained in the comment/rant section.I have read through this list and I have to say that after I purchased the router, which I ordered on-line, I was dreading it, but I have not had issues. It is possible that I am not using features that cause this issue. I believe the issues occur when using certain configurations with the "Enable Advanced DNS Service" enabled. I am not using this service. Since I knew people were having issue s with it, I wanted to see my results leaving that out. I have had this router running since a week before Christmas and I have many Virtual Server entires, QoS and port forwarding entries, https based remote administration, both 5GHz and 2.4GHz networks enabled supporting a/b/g/n(on both networks) and a guest network enabled on both bands all supporting WPA (TKIP and AES). I have 2 Giga wired connections that are always active, a 100Mb connection that is on an off but used almost daily, 2 Laptops that use the 2.4GHz network daily and one is 802.11g 54Mb and the other is 802.11n 150Mb and they are on at the same time almost daily, a printer that is on and used multiple times a week that uses 802.11g and a game system that uses 802.11a this device is used daily. Most devices are on and used at the same time daily and we have a good deal of regular Internet traffic and moderate other network traffic during these times. At night all computers are backed up over the network and most of the other network devices are off or not during this time. Other than having to reboot my Internet hardware provided by my ISP, I have not had issues. The router has been rebooted for config changes and I usually cycle it when I cycle the Internet hardware. Point is, so far no issues, good performance and it works and I have of course had other devices connected using the guest network and I have been testing features, performance, etc.
What's up with having so much variation in how features work across routers?e.g. My DHCP Reservation issue above. This router does not work with a setup like my DGL-4500.This router allows a preset amount of services like QoS and Virtual Server entries while the DGL-4500 just lets you add entries. Now maybe there is a limit and it just looks like there is no limit. Of course, there is at least a limit that is reached when you have used a certain amount of memory with the configuration.so many routers while leaving gaps and the lack of feature explanation and comparison?I switched to this router because I wanted a dual band setup which my DGL-4500 does not provide. That leads to the issue of the new way D-Link deals with dual-band. When I purchased the router it did not list that you had to choose 2.4GHz or 5GHz or it is not simultaneous dual-band. I was duped because I used to install DWL-7100AP for people that needed better wireless options for home businesses and small businesses and that provides simultaneous dual-band and back then if it was dual-band it was simultaneous. But I am disappointed in some of the features lost like WISH support and a few options here and there which do not seem like they are specific to gaming routers and this router is more on the mid range and low high range end of consumer, prosumer, home business and lower traffic small business routers, so why is it missing these features and why does it have the limitations I listed in the "variation in how features work" section above?
Other examples of lack of feature clarity are with Game Fuel, HD FUEL and Intelligent QoS. Isn't Game Fuel Intelligent QoS of some sort. Now from the example provided in the overview for the DGL-4500, Game Fuel optimizes game performance, but it does not say this is automatic or if it works along with the rules you set in the Game Fuel section which is the same as the QoS Engine section in the DIR-825. The difference is that the DIR-825 has a "Enable QoS Engine" option while the DGL-4500 has an "Enable Game Fuel" option. It seems that Intelligent QoS does what Game Fuel does, but expands that to VOIP, Media Streaming, etc. and it may be more automatic. HD Fuel in the only place I have seen it mentioned seems to refer to the combination of Intelligent QoS and the inclusion of 5GHz wireless support. Of course there is no version and feature documentation and in fact while the overview of the DIR-825 talks about gaming with Intelligent QoS, but if you bring up a comparison of routers, the chart has no in the gaming section for the DIR-825. I can't say I have noticed better or worse gaming performance with the DIR-825 compared with the DGL-4500, but given the shear lack of documentation on how to use Game Fuel and Intelligent QoS properly, who knows if I have this setup correctly. I will say the QoS Engine section in the DIR-825 is easier to use than the Game Fuel section in the DGL-4500.
1) The ability to reduce the brightness of the status lights, set them to solid if enabled with brightness options and to set them to off with an option to have some very faint light to show that the router is on. Of course I should be able to set different options to be applied at specific times.
2) Add the applicable features missing from the DIR-825 that are found in the DGL-4500 and applicable features from other routers. Also, get them all so they work the same on each router and let get the best from them all and make that the standard. e.g. In my DHCP reservation example above don't set the standard to the limitations of the DIR-825, but make the DGL-4500 function set or better function set of all routers combined for each feature the standard with-in router categories. e.g. the DIR-825, DGL-4500 and DIR-855 would be in the high end router category for consumer, prosumer, home business and lower traffic small business routers.
3) For DHCP reservations, you should not be limited to the DHCP IP Address Range.
4) On the log-in screen, get a better captcha and fix the tab order.
5) Add a log-out option in the web interface.
6) Allow for a next hop option in the DCHP server section. It would be cool, if there could be a list of IPs allows one to be enabled at a time.
7) Allow different DHCP server settings for each network. There are 5 on the DIR-825. Wired, 2.4GHz regular, 2.4GHz Guest, 5GHz regular and 5GHz Guest. Would be nice if you could set a couple of VLANs on the Ethernet ports and then have different DHCP setings for each VLAN.
For guest wireless networks, allow rules to be set to allow access to certain services on the network. E.g. I may want to allow printing. So allow a single port or multiple ports with easy settings for consecutive port ranges to be opened to an IP, IP range or all IPs and allow all ports for an IP or range of IPs. Of course, leave the allow full access option.
8a) Allow users to set rule sets that can be enabled/disabled like the full access option.
8b) Allow a control that can be set in the rule sets that controls if the wireless devices can talk to each other and another that controls if they can access devices on the wired network and another that controls if the wireless devices can access the Internet.
8c) Allow rules above to be limited to be applied to specific MAC Addresses.
8d) These options would be good to have for the non-guest wireless networks and wired network as well.
View 15 Replies
View Related
May 23, 2011
I picked up an E1200 and set it up successfully. I am using wireless MAC filtering, and decided to pull up the list of connected wireless clients (Wireless >> Wireless MAC Filter >> push "Wireless Client List" button).Immediately after this the Web UI of the E1200 becomes inaccessible. It still routes traffic, and the router remains pingable, but it will not allow access to the Web UI for several minutes. The error that appears upon attempt to access the Web UI during this time window is similar to the above, but reads "Error 102 (net::ERR_CONNECTION_REFUSED): The server refused the connection."
I have tried this in Google Chrome, Firefox 4, and MSIE on two separate computers. Each browser displays the error a bit differently (MSIE, for example, just says it can't display the page and gives no further detail) but the net results are always the same. I have tried resetting the device to factory defaults in addition to re-downloading the firmware from the Cisco/Linksys website and installing it. No improvement.
I have also noted that the Log (Administration >> Log; and yes, I have it enabled) doesn't appear to be picking up anything at all. In fact, the Security log, which supposedly (according to the Help) "displays the login information for the Router’s browser-based utility," is also blank.
View 9 Replies
View Related
May 18, 2012
I recently did a clean install of Win 7 64-bit Pro on my workstation. This was previously connected to my DNS (Windows server 2008 R2) which i use to host my files, music etc for my home network. I was previously able to see my network shares in windows explorer (client side) but now I don't. If i go to search box and \server the shared folders will then be displayed in windows explorer under network and i have access to them. I've done a small amount of digging but have so far found nothing to point me in the right direction. So while i have access i would like to be able to point windows media player to my shared music on the server, which i can't do now because I have no way to navigate to that folder. Same with other programs such as outlook, when i want to attach a file to an email i'm not able to navigate to the share. Weird as i have access to the share by search \server?
View 3 Replies
View Related
May 1, 2011
1. To specify static IPs for components on my network, is it simply a matter of reserving each component in the DHCP Reservations List portion of the Network Settings page?
2. On the same page, in the DHCP Server Settings portion, if Enable DHCP Server : is deselected, does this mean that only the hosts specified in the DHCP Reservations List can access the network? In other words, is access now restricted to these entries?
3. If the DIR-615 is powered OFF, will the above settings, etc. be lost (similar to a reset)?
View 6 Replies
View Related
Feb 15, 2012
I could get a list of clients on the E3200 wireless (or wired) ports. I have my E3200 setup as a WAP LAN-LAN off a switch and it is not the DHCP server on the network. I can see a list of MACs on the client list, but no client names and no IP addresses. They are definitely named and show up on the WRT54GL (DHCP and NAT) as devices
View 5 Replies
View Related
Dec 2, 2012
Cisco Adaptive Security Appliance Software Version 8.4(4)1
Device Manager Version 7.0(2)
Hardware: ASA5510, 1024 MB RAM, CPU Pentium 4 Celeron 1600 MHz
#show webvpn anyconnect
1.disk0:/anyconnect-win-3.1.00495-k9.pkg 1 dyn-regex=/Windows NT/
CISCO STC win2k+
3,1,00495
Hostscan Version 3.1.00495
Profile in atthach-file. After this profile is uploaded to client Optimal Gateway Selection doesn't work propertly: When 'vpn1.mydomain.com/mygroup' (it best TTL server) is unreachable, then OGS try to be connected to other servers, but without group-url, for example 'vpn2.mydomain.com' (instead of 'vpn2.mydomain.com/mygroup')
View 2 Replies
View Related
Aug 4, 2012
i m configuring a 887 router for ssl vpn. The goal is to configure full tunnel mode, so the client connect to the webpage generated by the router, it logs in, it has the "application svc" window where you can download the client and connect. Problem is everything is working except for the fact that the window with the ssl application doesn show up at all and so clients can't download the client and connect.
this is the relevant part of the configuration:
ip local pool sslvpnpool xxxxx xxxxxx
ip http server
ip http authentication local
[Code]....
View 3 Replies
View Related
Feb 5, 2012
192.168.0.1/Status/Device_Info.shtml, I have found LAN COMPUTERS that are not mine. How do I kick these away?Like this one: 192.168.0.169 Kajsas-iPhone 78:a3:e4:bf:48:ef
View 3 Replies
View Related
Jul 6, 2012
I have a Netgear WNDR4500 running the stock firmware, acting as a router for my home. I also have 2 routers that are flashed with DD-WRT (Linksys WRT54G and Asus WL-520GU) running as client bridges. The Netgear is 192.168.1.1 and the other 2 client bridges are 192.168.1.2 and 192.168.10.3. The Netgear router is performing DHCP giving addresses from 192.168.10.100 to 192.168.10.254. I have numerous machines connected to the Netgear, wirelessly and wired, and numerous machines wired to each client bridge. All machines have IP addresses that are 192.168.10.100, 192.168.10.101, 192.168.10.102, etc... Everything is working fine, but I have one question: When I access the Netgear router, it shows the client bridges as clients, machines that are wired and wireless to the Netgear router are listed as clients, but the client list does not show any clients that are connected to the client bridges. I assumed that since the router is performing DHCP that all clients would show up.
View 2 Replies
View Related
Jan 5, 2012
I have the WRT160N router for 3.5 yrs and it's worked perfectly since installing it. About two weeks ago it began intermittently dropping cable connection. First few times I thought I could resolve it by unplugging/plugging router & modem so they can "re-syn" to the cable connection. That still works but now it occurs sometimes multiple times within a few minutes/hours and then won't happen again for an entire day/days. The other day I had connectivity but instead of the usual 5 bars I only had 3 while using my laptop in the same spot in the house as usual.
View 5 Replies
View Related
Mar 1, 2012
I recently change routers to a Linksys E3000 wireless router from a Uverese 2wire residential gateway and all worked well for a short time nothing changed however when I go to view network devices from Win7,Vista or XP computers the network devices are no longer there. when I shut down and reboot the router and switches I still cannot see these devices, however when I hook up my old 2wire router I see my devices again. Even when I reconnect to the E3000 all the devices can be viewed for a few hours. Changing routers resets something but maybe overloads the linksys E3000 after a few hours? maybe this E3000 is just defective?
When I view a network map in Network & Internet all the devices appear in the map The configuration is Linksys E3000 router with two (2) 8 port Trendnet gigabyte switches and One (1) 8 port Trendnet Poe 10/100 switch. They are chained router to 8 port gig to 8 port gig to 8 port Poe 10/100. Prior to this I had the router to each switch separately - - this does not seem to matter works the same either way
Devices attached - Network printer,XP desktop, Vista Desktop, NAS, WDTVlive media player, Roku, Home automation controller, IP touch screen for the automation, security DVR (wireless devices are all ok Win7 laptop, Vista laptop, Ipad)seldom are more than 3 devices being used at one time light traffic.)
View 2 Replies
View Related
Feb 2, 2011
Today when I tried to add a network printer,list of browsed printers in network is shown as pc1/hplaser1, pc1/hplaser2, pc2/hplaser1, pc7/hplaser1 and so on. They are all network printers, not local printers.Then why it is not showing the printers alone, why they show the pcs in the network and the same printer is shown in different pcs as they are installed in all of them.
View 2 Replies
View Related
Jul 3, 2012
I've got an E4200v1 running 1.0.04 firmware with guest access enabled. I'd like to find out who is logged in using the guest access. Is there a way to get a list of the DHCP clients on the guest network? I'm able to do this for the non-guest access via the WEB interface's Status->Local Network->DHCP Clients Table page. But I can't find a similar table for the guest network.
View 3 Replies
View Related
Aug 15, 2012
Have an older laptop running XP Home, Desktop running XP Pro with printer on it. Wireless network setup and doing fine for bidirectional file share and print share from old lappie to desktop. All worked great.Bought a brand new high end laptop with Win 7 (not impressed). Finally got the Win 7 new one to recognize both older computers on the Win 7 computer and was able to access file share and print on the desktop. Thought I was doneNope, now while I can see the old lappie and it can see it in the Win7 computer both directions give me cannot access the drive or specific files even though it "sees" themAll files and disks are set to full share. No password is required or any homegroup is setup on the win 7 system. I've been in the bus. a long time so you know I'm at the end of the rope. All searches through knowledge base and the web have yielded no results to this.I did find an absolute to this in insuring that both systems have the same workgroup. Changed the old lappie to the right name. Made no difference in access (after several reboots). Obviously can't run Easy Transfer with this situation.
Now problem #2. I changed the old lappies workgroup to the same as the Win7 computer in the hopes of fixing this. Made no difference but now I have two iterations my XP laptop in the Win 7 system.When selected, the info for one has the old workgroup and selecting the other shows the new workgroup (matching the Win7 workgroup).Anyway, throwing up my hands in frustration and disgust. Find no way to even dump the old workgroup map listing. Jeez. Sure glad they (M/S) made this better?
View 7 Replies
View Related
