E3000 - Accessible Network Devices Cannot Be Seen In List Of Computer

Mar 1, 2012

I recently change routers to a Linksys E3000 wireless router from a Uverese 2wire residential gateway and all worked well for a short time nothing changed however when I go to view network devices from Win7,Vista or XP computers the network devices are no longer there. when I shut down and reboot the router and switches I still cannot see these devices, however when I hook up my old 2wire router I see my devices again. Even when I reconnect to the E3000 all the devices can be viewed for a few hours. Changing routers resets something but maybe overloads the linksys E3000 after a few hours? maybe this E3000 is just defective?

When I view a network map in Network & Internet all the devices appear in the map The configuration is Linksys E3000 router with two (2) 8 port Trendnet gigabyte switches and One (1) 8 port Trendnet Poe 10/100 switch. They are chained router to 8 port gig to 8 port gig to 8 port Poe 10/100. Prior to this I had the router to each switch separately - - this does not seem to matter works the same either way

Devices attached - Network printer,XP desktop, Vista Desktop, NAS, WDTVlive media player, Roku, Home automation controller, IP touch screen for the automation, security DVR (wireless devices are all ok Win7 laptop, Vista laptop, Ipad)seldom are more than 3 devices being used at one time light traffic.)

View 2 Replies


ADVERTISEMENT

Wireless Network - List Of Devices And NAT Settings?

Jan 17, 2011

I recently added several devices to my wireless-g network: Xbox 360, an HTC Smart phone, and an old laptop my buddy gave me (in addition to the 2 desktops that were already on the network). Since doing this, I've had occasional buffering problems when streaming music or video, even when I'm only using 1 of the devices. I suspect that the Xbox (or maybe phone) is downloading updates in the background, even when it's turned off, and that is consuming bandwidth. Is there any way I can see a list of devices that are connected to the network and maybe even the amount of data being transmitted to/from each so I can find the culprit. when I play online, it says that my NAT settings are not open and that this makes it take longer to connect to other players. What are the risks involved in loosening the NAT restrictions?

View 1 Replies View Related

Linksys Wireless Router :: Find Log Or List Of Devices That Attempted To Access EA4500 Wi-Fi Network?

Aug 31, 2012

Where can I find a log or list of devices that attempted to access my EA4500 wireless network?I am using the cloud services to monitor my EA4500 usage in an apartment environment.

View 1 Replies View Related

Linksys Wireless Router :: E3000 / Connecting Devices To Network

Nov 12, 2010

I have 3 computers in total: 2 desktops and 1 laptop.
 
1. My primary PC is connected physically to my router.

2. My (downstairs) laptop is connected to the wireless.

3. My other PC connects to the wireless network via USB wireless adapter.
 
I was having issues getting #3 connected to the wireless network.  I used the Wi-Fi Protected Setup™ PIN number provided to me by the Linksys Wireless Manager to no avail.  The E3000 router and #3 could never find each other.After calling support, it turns out that more often than not, "other" wirless management software (in my case Linksys  Wireless Manager that came with the USB device) was interfering with my Windows XP Wireless Manager.Rule of thumb: Always let your native operating system manage the wirless networks that are available to it.  It does a far better job and is 10x more reliable than software provided by 3rd party vendors.Specific to my case: Windows XP, I had to enable the Windows Wireless Manager and uninstall the Linksys Wireless Manager Software. Here it is...Enabling Windows Wireless Manager These directions are for Windows XP:

1) From the Windows Start menu, click Control Panel.

2) Click Network and Internet Connections.

3) Click Network Connections.

4) Right-click the icon for your "wireless network connection", then click Properties.

5) At the top of the window, click the Wireless Networks tab.

If the "Wireless Networks" tab does not appear between the "General" and "Advanced" tabs, you are not on/in the wireless network connection settings:a) click cancelb) Right-click the icon for your wireless connection and choose "Enable". c) return to step 4 6) Check the checkbox next to "Use Windows to configure my wireless network settings".
 
These directions are for Windows Vista:

1) Go to the Windows start menu and then the control panel.

2) Open Network and Sharing Center.

3) Click Manage Network Connections (from the left side menu).

4) Right click on the network adapter 'Wireless Network Connection' and choose "Properties" and click "Continue".

5) At the top of the window, click the "Wireless Networks" tab.

If the "Wireless Networks" tab does not appear between the "General" and "Advanced" tabs: a) click cancel b) Right-click the icon for your wireless connection and choose "Enable". c) Return to step 4

6) Check the checkbox next to "Use Windows to configure my wireless network settings".

View 7 Replies View Related

Cisco :: 1240 AP / 4402 WLC - VLans To Be Accessible To Wireless Devices

Sep 27, 2012

We have four VLANs that need to be accessible to wireless devices. The VLANs serve the following groups: staff, student, guest, phone
 
We are currently using a WEP/MAC authentication for staff and phone wireless networks.
 
I am looking for what your recommendation would be to provide reasonable level of wireless security, particularly with the staff network, but at the same time not require a high level of management, ex. managing active and inactive MAC addresses for MAC authentication. We have the following components available - 1240 APS, Windows AD, a 4402 WLC, and 6 campuses, and outdated Cisco ACS.We need to provide connectivity to Cisco wireless phones, laptops, iPads, cell phones.

View 2 Replies View Related

Computer Not Accessible From Server By Name?

Mar 19, 2011

I'm working on a small network (1 server, 6 workstations, stand-alone, not connected to the main Company Network) "reinstalling" a Workstation. Re-imaging from semi-generic Norton Ghost image (4 of the 6 Workstations run the same programs with different addresses). I then had to reset the IP, the Computer Name, and then the Domain (I did it in that order).

I'm using Windows Server 2003 as the domain controller, and the Workstation is Xp Pro Sp 2.

The Workstation is using the same IP, Name, User as before, and they were working with the server previously (a program had corrupted prompting the reinstall).

The problem is that if I open windows explorer and type in the Workstations IP (\000.00.0.1) I get access to the computer. But if I go there and type in the Workstations Name (\Computer01) I get a "you may not have permission to use this network resource" error.

If I go to the work station, and try the same thing except with the Server's IP (\000.00.0.100) and Name (\Server01) I get access.

This Workstation controls an I/O device that is used by a program running on the server (most of the time, not while I'm doing the install of course) and the program uses the Workstation's Computer Name to access it.

As far as I can tell all the settings on this Workstation match the 3 that are running the same programs, but I could have missed something.

I'm a bit stumped by this, I don't normally deal with the Server side of the computers. I usually just set up the workstations to whatever Name/IP the Net-admins give me. But my bosses put me in charge of this little network, mainly because the Net-admins din't want to deal with it.

View 2 Replies View Related

Internet Accessible But Cannot Access Other Computer On LAN

Aug 15, 2012

I have a Windows 7 machine that is wired to the router. I have Windows XP computer that is wireless in another room. Signal is showing 80% and internet is accessible and fast from both systems; but, I cannot access either computer from the other computer. I got the IP addresses of each machine and I cannot ping from either direction. Firewalls are turned off on both systems.When I type in \server, I get an error that say I should check my spelling or use the windows Search; but, that doesn't work.

View 5 Replies View Related

Linksys Wireless Router :: EA6500 Does Not List AppleTV Devices

Apr 30, 2013

I have an EA6500 and have three AppleTV... all three generations.l  I also have a DirecTV Genie and DirecTV HD-DVR that, together, provide whole-house viewing.  When I first setup the EA6400 based network, all three AppleTVs were listed and my whole-house viewing worked.  This past Saturday, however, that changed, when I couldn't see the programs recorded on the HD-DVR, from the Genie.  My troubleshooting determined one of the AppleTVs had been assigned the same address as the HD-DVR upstairs and that the HD-DVR wasn't listed as being connected.  Once I reset everything, the IPs resolved and the whole-house viewing was resolved, however, none of the AppleTVs are listed as connected, even though they are.  I can check the connections by the AppleTV device and see that they do, indeed, have an IP address, and I can view material from the iTunes cloud or stored on another PC in the local network.  I reset everything again, but to no avail.  No AppleTV devies show as connected from Smart Wi-Fi.  The AppeTVs are all wired to the LAN... not wireless.
 
So, the question is, is there a fix to get AppleTV devices to list?  All of my devices and router have the lastest firmware.  BTW, I had a WRT610N, which I'm now useing as an access point, didn't have this issue.

View 9 Replies View Related

D-Link DIR-655 :: Devices Connected Not Showing In Device Info List

Apr 26, 2011

I just got a DIR-655 and set it all up pretty easily. I have 6 wired and 3 wireless. All work fine and all are set to use DHCP. But if I go (in the router) to the Lan Computers list under Device Info, three devices (2 wired, 1 wireless) do not appear. I do have a switch added to the system, but of the three devices connected to it, 1 shows in th Lan Computers list and the other 2 do not.Since everything works, I'm mostly just curious why this is. Every previous router I've had showed everything correctly.

View 3 Replies View Related

Cisco Routers :: RVL200 - Using Static IP List To Block Devices

Nov 29, 2011

which current SB routers support these features known from RVL200 and RV0XX v. 1.X?:
 
Block MAC address on the list with wrong IP address

Block MAC address not on the list

View 1 Replies View Related

Cisco Switching/Routing :: List Of Supported External HDDs / NAS Devices For 857w Router?

Mar 19, 2012

Where can I find a list of supported external HDDs or NAS devices for a Cisco 857w router?

View 2 Replies View Related

Linksys Wireless Router :: Monitor Devices Connected In E3000?

Nov 16, 2011

I've got the E3000 set up and working.  What I'd like to do now is monitor all the devices' connectivity to it. The bandwidth it consumes and stuff.  Is there a way to do that on my router?

View 6 Replies View Related

Linksys Wireless Router :: How To Get E3000 Or E4200 To Manage More Than 5 Devices

Mar 11, 2012

How can I get a E3000 or E4200 to manage more than 5 devices? Come on Cisco, lets get real. EVERYONE has more than 5 devices to manage. The average family of 4 has 3 or 4 computers, 4 smart phones and at least a couple of tablets and maybe some TV or game consoles. Setting access control policies is a must for anyone who is a parent.
 
Any good router that has a reasonable set of access control features? I've always loved Cisco up to this point, but I'm frustrated by this significant limitation.

View 9 Replies View Related

Linksys Wireless Router :: E3000 - How To Make Ethernet Devices Available

Oct 4, 2012

I have been using the E3000 for quite a while. A problem that I could not find a solution to is that the devices connected through Ethernet can't be viewed on Wireless, and vice versa. This is especially annoying because I want to get access to my media servers over wireless, for obvious reasons, but even those are not viewable (and using IP addresses on portables is a pain in the back)

View 4 Replies View Related

Linksys Wireless Router :: Devices Connected To E3000 Via Wifi But Not With Internet

Apr 21, 2013

My E3000 has been working fine with 1.0.04 build 6 FW. Recently some devices (kindle, iPad) can't connect to internet while connected to E3000 via WiFi network. Had a look my E3000 router IP is 192.168.0.1 but those problematic devices has IP 192.168.1.XXX allocated by DHCP not sure why. Currently I manually set up static IP 192.168.0.XXX for those devices.

View 1 Replies View Related

Linksys Wireless Router :: E3000 Scheduled Access For Kids Devices

Jul 8, 2012

I am running an E3000 with Firmware - 1.0.04.
 
I would like to schedule my boys ipods to be on the network from 2:00pm to 4:00pm each day.
 
Running the Cisco connect software it would appear I can schedule from 2pm until the next morning but not a 2 hour window in the same afternoon.
 
Looking through other posts I see earlier software where this can maintained through the Router firmware but with 1.0.04 I seem to have to use Cisco Connect.
 
So how can this be done with my current configuration ?

View 3 Replies View Related

Computer Not Showing Up In DHCP Client List?

Feb 9, 2011

I just started having this problem yesterday. I was experiencing weird downloading/internet browsing issues and couldn't figure out what the problem was. I started looking around my router settings and noticed that in my DHCP Client list, my computer isn't in it. The router is hooked up to the computer, so it's not wireless. My phone and my girlfriend's laptop are listed, but the main computer isn't. It's especially causing problems with port forwarding. Downloads will stop because the port isn't showing as open. I'm running 64 bit Windows 7 and a Belkin N+ Wireless Router, model F5D8235-4.Firmware is up to date.

View 6 Replies View Related

D-Link DIR-655 :: How To Remove Computer From List Of LAN Computers

Feb 5, 2012

192.168.0.1/Status/Device_Info.shtml, I have found LAN COMPUTERS that are not mine. How do I kick these away?Like this one: 192.168.0.169   Kajsas-iPhone   78:a3:e4:bf:48:ef

View 3 Replies View Related

D-Link DIR-655 :: Can't Find Computer In DHCP List

Apr 19, 2011

i had the dir-655 with desktops and laptops running with xp and win 7, also some other devices such as ipod, iphone, ps3, xbox, problem occura with conflict of network ip address, i think xp and win 7 both login with the same network ip address.  So I start to disconnect every device and try to connect each desktop and laptops, one by one, enabled the DHCP and reserve the network ip to avoid conflict.  But here's the problem, when I connect the first computer with wired to the dir-655, can't find the computer in the DHCP list so I cannot do the reserve, I'm able to surf internet even I can see info with ipconfig.  So I connected 1 wired and 2 wifi to the network, only 1 wifi network ip showing on the list, so I reserve that one, but after I refresh, the DHCP list is empty.

View 1 Replies View Related

Linksys Wireless Router :: E3000 Running As Access Point Drops Devices

Nov 25, 2012

I am running the e3000 as an access point.. My iphone and ipad connect to it seamlessly. After a few hours to days, they are no longer recognized by the router. Nothing I reset on the phone or ipad makes any difference. The only solution I have found is to re-boot the router. They then re-connect on their own.

View 4 Replies View Related

Network :: Getting Message - PC Is Not Accessible?

Jul 8, 2012

I was trying to connect my computers on a home network so that I can access either one via the other.When I try however I get the message:

"***-PC is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions.

long failure: user account restriction. Possible reasons are blank passwords not allowed, logon hour restrictions, or a police restriction has been enforced.

That is the message from computer 1 to computer 2.

Computer 2 gives me the message:

Windows cannot access \***-PC

Check the spelling of the name. Otherwise, there might be a problem with your network. To try to identify and resolve network problems, click Diagnose.

View 2 Replies View Related

Home Network Share Not Accessible But Other One Is

Mar 26, 2011

I have a fairly simple wireless home network. My main desktop machine is running XP Pro, and our family laptop is running XP Home. The laptop shares the My Documents folder for 2 of the 3 profiles. One of them works as it should. It is visible and accessible on the main desktop machine, but the other share is visible but NOT accessible. I get the following error message when I try to explore it from the main desktop machine:

<the share name> is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions.

Access is denied.

I'm not sure when this started, but remember that the other folder being shared is working just fine. I've double and triple checked the settings, share names, and basically anything I could possibly mistype. I've restarted both PCs, and refreshed the network explorer via both the file explorer and My Computer dialog. The My Computer dialog refresh the shares for some reason that the explorer wouldn't, but I'm still denied access to that one share on the laptop.

View 2 Replies View Related

Cannot Ping System But Network Accessible

Jun 29, 2012

Cannot Ping System but system can ping everyone on the network accessible

View 2 Replies View Related

Shared Files Not Accessible On Network

Jan 19, 2011

I have a router-based home network in which the desktop running XP media center is connected by cable to the router. There are 2 wireless laptops, one running XP home and the other Windows 7.The laptops can talk to each other, and the desktop can talk to the laptops.But I cannot access the desktop from the laptops. I can see the (shared) folders, but when I click on one I get the message: "You might not have permission to use this network resource..Not enough server storage is available to process this command." One solution suggested in several places is to change the IRPStackSize to 15. However, if I start the desktop in safe mode with networking, I can access the files.I can also access the machine using remote desktop.One extra frustration is that this is a problem that has happened relatively recently. It used to work OK.

View 8 Replies View Related

Linksys Wireless Router :: E3000 Connection With Computer?

May 6, 2012

My E3000 looses connection whenever any other computer connects whether it is a wired or wireless computer, IPAD, Mac, or anything else we have.  It goes on and off any time two have connected and when it works it is very slow once another machine connects.  Eventually it makes my network completely shut down.

View 1 Replies View Related

Home Network :: Asus RT-N13U DD-WRT Web UI Not Accessible?

Dec 10, 2012

I flashed my router to DD-WRT, but I could not access the web UI which is suppose to come on typing 192.168.1.1 in the web browser. . It used to come fine before but I reflashed to Asus Firmware but now I cannot access it. I have tried several times to flashing it to Asus Firmware and Back to DD-WRT, but it didn't work. When I flash to ASUS everytime my old settings are still the same. I tried assigning a static IP also.

View 1 Replies View Related

Workgroup Is Not Accessible - You Might Not Have Permission To Use This Network Resource

Sep 17, 2012

I have a network with aprox 150 workstations (90% windows XP profesional, 10% Windows7 32 or 64 bit), and I receive from time to time this message ONLY on windows XP workstations:" Workgroup is not accessible.You might not have permission to use this network resource" All the time I could access the various workgroup computers by entering their IP like \192.168.1.5 or \mikepc All the time i can ping any of the workstation without any problem.All the time using Search computers on the network I find computer name.

View 1 Replies View Related

Desktop Not Accessible From Laptop In Home Network

Aug 19, 2011

My desktop is not accessible from my laptop in my home network. This seemed to happen all of a sudden.Contact the administrator of this server to find out if you have access. PS: I can access the laptop from my desktop.

View 14 Replies View Related

Wireless Network Is Not Accessible From Dell D830

Feb 4, 2012

I have a Dell D830 that was given to me. I bought a new hard drive and restored the operating system to XP. I can't access the internet now through my wireless network at home. I've tried to setup a new connection in the network connection but that's there is nothing to connect to, nothing is working.

View 3 Replies View Related

Network Drive Not Accessible If Antivirus Avg Installed?

Jun 20, 2012

My network drive is not working if i install antivirus. It shows 'access denied". if I uninstall, i can access the network drive.

View 3 Replies View Related

D-Link DIR-655 :: Internet Accessible But No Network Access

Mar 4, 2011

Internet access is working fine, however I cannot get my computers to work on the network therefore cant share any files or play any network games.  The router is set up as DHCP server therefore IPs are automatically assigned, this is setup on the PCs and the router.  The work group is also set.  Exactly same settings basically as my old router which worked fine but wont on this one!  I have 3 wired PCs and a wireless laptop.  2 PCs are windows XP the other is Windows 7 and the laptop is windows 7.  The wireless win7 laptop will recognize my win7 wired PC and vice versa and can share everything without problems, but they wont have anything to do with the wired winxp PCs, on top of that the 2 winxp wont recognize each other either so don't think its anything platform specific. I have also tried setting up static IPs for each computer - still no joy.This is a brand new D-Link DIR-655 Rev B1 firmware 2.00

View 3 Replies View Related

Windows 7 Can't Receive Internet Network Traffic - Gateway Accessible

Aug 18, 2012

I just got my dad's old notebook (VAIO VPC F223FB) which is better than my older one. So, I did a backup and then managed to clean install a Windows 7 Professional x64.At first I had a problem with the drivers, because the internet wasn't connecting and the USB ports weren't detecting my External Drive. So, I tested other USB port and got it. Installed the drivers and I could connect to the wireless network. But it doesn't detect the ethernet cable! And I want it detecting because then it's faster. I already tried downloading the Ethernet Controller driver. At first, I downloaded through Sony's support site but it didn't recognize the driver. Now, it recognizes but still doesn't connect it. And when I tried Solving Connection Problems, it said the network gateway was accessible but Windows can't receive Internet network traffic.

View 5 Replies View Related

Cisco VPN :: ASA5510 Remote Access / LAN Not Accessible Inside Network

Jan 6, 2013

I am facing a problem with Cisco ASA remote access VPN, the remote client is connected to VPN and receiving IP address but the client is not able to ping or telnet any internal network.I have attached running configuration for your reference.
 
-FW : ASA5510

-Version : 8.0
 
Site to Site VPN is working without any issues

View 10 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved