Wireless Network Is Not Accessible From Dell D830

Feb 4, 2012

I have a Dell D830 that was given to me. I bought a new hard drive and restored the operating system to XP. I can't access the internet now through my wireless network at home. I've tried to setup a new connection in the network connection but that's there is nothing to connect to, nothing is working.

View 3 Replies


ADVERTISEMENT

Dell Latitude D830 Will Not See Router And Network Devices

May 31, 2012

I'm trying to hook up my boss's service laptop (the aforementioned Dell Latitude D830) to a Netgear GS108 router so that he can check out footage from a couple of Pelco Sarix IP security cameras.Long story short, not only does the included software not detect the cameras, upon closer inspection, I cannot ping the Netgear router from an XP command prompt (when trying to do so, I received "Request timed out" messages, then Sent 4, Received 0, Lost 4, 100% loss).

Additional info- This PC has had quite a lot of setup work done to it so that it would run DOS as it is used to connected to a 15-year-old fire alarm system for programming and auditing purposes. This happened well before I was hired and my boss is not a computer person so the extent of this work is basically beyond what I can readily see- namely a partitioned HDD with DOS and a dual boot. The connection between the fire system and the PC is a serial connection facilitated by an actual serial port in the laptop. I don't know what effect, if any, this has had on the XP (sp3) portion of things.

This PC is not generally on a wired network; I mention this mainly to say its not online at work, doesn't receive an IP address from a DHCP somewhere, etc. My boss says he sometimes takes it home and connects to his home WiFi with it however. Additionally, it is not a device that belongs to our customer so it cannot be placed on their network (which is the only network and internet connection available to me). When I plug the CAT5 cable into the laptop, both LEDs flash very briefly, then a single orange LED illuminates solidly and stays that way. On the router, I get two green LEDs (which signifies gigabit speed, apparently). If I open Control Panel and click on Network Connections, I see the NIC and it appears to be connected with no issues. Double-clicking the icon shows Status: Connected at a speed of 1.0Gbps.

The IP cameras work fine. I took them home, connected them to my own home router (which other than opening some game ports, I've done nothing special with; a Linksys WRT54G). The cables I'm using are the same ones I used at the house. Note that I did NOT use this laptop when I tested them at my house- I used my own desktop PC (nothing special, except I have no antivirus, software firewall, etc.- read on).The Netgear router is technically an unknown quantity, but it is literally brand-new out of the box this morning. I had this same issue I'm currently having with a couple of "found" routers (meaning my boss/ co-workers probably found them in the trash somewhere). Naturally, I assumed both routers were bad based on the fact that the cameras worked fine at my house (again, with my PC- not this Dell laptop).

There is protective software on this PC. I have disabled the Windows Firewall via Control Panel and in Norton 360, I've enabled "Silent Mode", disabled Smart Firewall and Anti-Virus Auto Protect. I'm loathe to completely uninstall this suite because of some of the stories I've heard my boss tell about the users on his home network. This PC is the sole link to the customer's fire alarm system and has been configured (again, long before I was hired) extensively to do so. What I'm looking for mostly is something I'm missing. When I first began having issues with this system, I went into the LAN Properties for the NIC, turned off the "Obtain IP Address Automatically), and entered 192.168.1.10 for the IP, 255.255.255.0 for the subnet, and 192.168.1.1 for the gateway (based on the Netgear router's published default IP setting). When that didn't work, I tried all of the above and switched the gateway to 192.168.0.1 as the manufacturer seemed to indicate it could be either address. Same results.

View 6 Replies View Related

Dell :: Latitude D830 - Wireless 1395 WLAN MiniCard Not Found

Nov 5, 2012

I have a Latitude D830 that I had to reinstall back to Windows XP3. I have installed all the drivers per instructions except that the device manager indicated one ethernet controller (Wireless 1395 WLAN MiniCard) is not found. I ran the desired driver R242906 but it begins and then states that hardware is not found and stops. I have tried some of the older drivers as well but still have had the same result.

Prior to redoing the OS is was Windows Vista Pro but kept crashing so went back to XP. The wireless card worked then.

View 1 Replies View Related

Dell :: Latitude D830 - Can't Connect To Internet After Reformat

Jun 4, 2009

I had to reformat a Dell Latitude D830 with XP Pro SP2 due to a trojan.  After XP was reinstalled, I inserted the cds which contain the drivers and such for my system.  I installed the drivers and utilities, but for some reason when I plug my ethernet cable into the laptop, it says there is "Little or No Connectivity".  I plugged the same ethernet cord into the desktop I am currently using, and it works just fine.  The connection comes straight from the wall to the computer with no router or modem involved. 

View 7 Replies View Related

Dell Dimension 9150 / Workgroup Is Not Accessible

Dec 28, 2011

My network contains:

-Netgear router 1
-Dell Dimension 9150 - Windows XP pro SP3 (this machine, connected to router 1 using a pair of netgear powerline adapters
-2 x Dell Inspiron laptops - Windows 7 Home 64bit (wireless)
-iMac - OSX Snow Leopard (wireless)
-Apple Time Capsule (network drive)
-Several misc items (phones, iPod/iPad, Vodaphone sure signal, PS3)
-Network printer
-Netgear router 2 (used as wireless access point the otherside of the house, connected using a pair of netgear powerline adapters) CURRENTLY DISABLED

None of the 4 computers can see each other, but they can all print and access the Time Capsule. Now I've made sure they're all on the same workgroup and that relevant services for sharing files are running. When I try to "View workgroup computers" on the XP machine I get the error attached.

View 5 Replies View Related

Linksys Wireless Router :: X3000 FW V1.0.03 - Internal Network Not Accessible Via WLAN?

Feb 1, 2013

I am experiencing one, possibly two problems with the X3000, firmware release v1.0.03:
 
1. When enabling guest mode, the internal network is not accessible via WLAN even for clients NOT connected via guest mode but regularly: Even non-guests but regularly connected clients can't access any internal IP but the router itself. netscan shows only the very client's IP and the router's. Only after switching guest mode entirely off, regularly connected clients can access interal IP again. netscan correctly shows the whole network. Obviously a firmware bug. BTW: Clients connected via cable do not experience this problems.
 
2. I am not sure about this, but after using the firmware built in "Reboot" button, the router reboots correctly. But for some reason, it is instable afterwards. It is operational for a few seconds but then reboots again. It keeps cycling. I could stop it by switching the router off and on again.
 

View 6 Replies View Related

Network :: Getting Message - PC Is Not Accessible?

Jul 8, 2012

I was trying to connect my computers on a home network so that I can access either one via the other.When I try however I get the message:

"***-PC is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions.

long failure: user account restriction. Possible reasons are blank passwords not allowed, logon hour restrictions, or a police restriction has been enforced.

That is the message from computer 1 to computer 2.

Computer 2 gives me the message:

Windows cannot access \***-PC

Check the spelling of the name. Otherwise, there might be a problem with your network. To try to identify and resolve network problems, click Diagnose.

View 2 Replies View Related

Home Network Share Not Accessible But Other One Is

Mar 26, 2011

I have a fairly simple wireless home network. My main desktop machine is running XP Pro, and our family laptop is running XP Home. The laptop shares the My Documents folder for 2 of the 3 profiles. One of them works as it should. It is visible and accessible on the main desktop machine, but the other share is visible but NOT accessible. I get the following error message when I try to explore it from the main desktop machine:

<the share name> is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions.

Access is denied.

I'm not sure when this started, but remember that the other folder being shared is working just fine. I've double and triple checked the settings, share names, and basically anything I could possibly mistype. I've restarted both PCs, and refreshed the network explorer via both the file explorer and My Computer dialog. The My Computer dialog refresh the shares for some reason that the explorer wouldn't, but I'm still denied access to that one share on the laptop.

View 2 Replies View Related

Cannot Ping System But Network Accessible

Jun 29, 2012

Cannot Ping System but system can ping everyone on the network accessible

View 2 Replies View Related

Shared Files Not Accessible On Network

Jan 19, 2011

I have a router-based home network in which the desktop running XP media center is connected by cable to the router. There are 2 wireless laptops, one running XP home and the other Windows 7.The laptops can talk to each other, and the desktop can talk to the laptops.But I cannot access the desktop from the laptops. I can see the (shared) folders, but when I click on one I get the message: "You might not have permission to use this network resource..Not enough server storage is available to process this command." One solution suggested in several places is to change the IRPStackSize to 15. However, if I start the desktop in safe mode with networking, I can access the files.I can also access the machine using remote desktop.One extra frustration is that this is a problem that has happened relatively recently. It used to work OK.

View 8 Replies View Related

Home Network :: Asus RT-N13U DD-WRT Web UI Not Accessible?

Dec 10, 2012

I flashed my router to DD-WRT, but I could not access the web UI which is suppose to come on typing 192.168.1.1 in the web browser. . It used to come fine before but I reflashed to Asus Firmware but now I cannot access it. I have tried several times to flashing it to Asus Firmware and Back to DD-WRT, but it didn't work. When I flash to ASUS everytime my old settings are still the same. I tried assigning a static IP also.

View 1 Replies View Related

Workgroup Is Not Accessible - You Might Not Have Permission To Use This Network Resource

Sep 17, 2012

I have a network with aprox 150 workstations (90% windows XP profesional, 10% Windows7 32 or 64 bit), and I receive from time to time this message ONLY on windows XP workstations:" Workgroup is not accessible.You might not have permission to use this network resource" All the time I could access the various workgroup computers by entering their IP like \192.168.1.5 or \mikepc All the time i can ping any of the workstation without any problem.All the time using Search computers on the network I find computer name.

View 1 Replies View Related

Desktop Not Accessible From Laptop In Home Network

Aug 19, 2011

My desktop is not accessible from my laptop in my home network. This seemed to happen all of a sudden.Contact the administrator of this server to find out if you have access. PS: I can access the laptop from my desktop.

View 14 Replies View Related

Network Drive Not Accessible If Antivirus Avg Installed?

Jun 20, 2012

My network drive is not working if i install antivirus. It shows 'access denied". if I uninstall, i can access the network drive.

View 3 Replies View Related

D-Link DIR-655 :: Internet Accessible But No Network Access

Mar 4, 2011

Internet access is working fine, however I cannot get my computers to work on the network therefore cant share any files or play any network games.  The router is set up as DHCP server therefore IPs are automatically assigned, this is setup on the PCs and the router.  The work group is also set.  Exactly same settings basically as my old router which worked fine but wont on this one!  I have 3 wired PCs and a wireless laptop.  2 PCs are windows XP the other is Windows 7 and the laptop is windows 7.  The wireless win7 laptop will recognize my win7 wired PC and vice versa and can share everything without problems, but they wont have anything to do with the wired winxp PCs, on top of that the 2 winxp wont recognize each other either so don't think its anything platform specific. I have also tried setting up static IPs for each computer - still no joy.This is a brand new D-Link DIR-655 Rev B1 firmware 2.00

View 3 Replies View Related

E3000 - Accessible Network Devices Cannot Be Seen In List Of Computer

Mar 1, 2012

I recently change routers to a Linksys E3000 wireless router from a Uverese 2wire residential gateway and all worked well for a short time nothing changed however when I go to view network devices from Win7,Vista or XP computers the network devices are no longer there. when I shut down and reboot the router and switches I still cannot see these devices, however when I hook up my old 2wire router I see my devices again. Even when I reconnect to the E3000 all the devices can be viewed for a few hours. Changing routers resets something but maybe overloads the linksys E3000 after a few hours? maybe this E3000 is just defective?

When I view a network map in Network & Internet all the devices appear in the map The configuration is Linksys E3000 router with two (2) 8 port Trendnet gigabyte switches and One (1) 8 port Trendnet Poe 10/100 switch. They are chained router to 8 port gig to 8 port gig to 8 port Poe 10/100. Prior to this I had the router to each switch separately - - this does not seem to matter works the same either way

Devices attached - Network printer,XP desktop, Vista Desktop, NAS, WDTVlive media player, Roku, Home automation controller, IP touch screen for the automation, security DVR (wireless devices are all ok Win7 laptop, Vista laptop, Ipad)seldom are more than 3 devices being used at one time light traffic.)

View 2 Replies View Related

Windows 7 Can't Receive Internet Network Traffic - Gateway Accessible

Aug 18, 2012

I just got my dad's old notebook (VAIO VPC F223FB) which is better than my older one. So, I did a backup and then managed to clean install a Windows 7 Professional x64.At first I had a problem with the drivers, because the internet wasn't connecting and the USB ports weren't detecting my External Drive. So, I tested other USB port and got it. Installed the drivers and I could connect to the wireless network. But it doesn't detect the ethernet cable! And I want it detecting because then it's faster. I already tried downloading the Ethernet Controller driver. At first, I downloaded through Sony's support site but it didn't recognize the driver. Now, it recognizes but still doesn't connect it. And when I tried Solving Connection Problems, it said the network gateway was accessible but Windows can't receive Internet network traffic.

View 5 Replies View Related

Cisco VPN :: ASA5510 Remote Access / LAN Not Accessible Inside Network

Jan 6, 2013

I am facing a problem with Cisco ASA remote access VPN, the remote client is connected to VPN and receiving IP address but the client is not able to ping or telnet any internal network.I have attached running configuration for your reference.
 
-FW : ASA5510

-Version : 8.0
 
Site to Site VPN is working without any issues

View 10 Replies View Related

Cisco Firewall :: ASA5520 Unit Not Accessible On Network For Initial Configuration

Dec 15, 2011

We received an ASA5520-K8 through Cisco's Loan program so we could demo it as a replacement for our aging Cisco 3005 VPN appliances.  Given that we are a non Cisco shop (except for specific appliances like concentrators and wireless access points), I don't have a great deal of experience with Cisco gear.I started to set to setup the appliance this morning but immediately ran into issues.  The 5520 doesnt seem to be acting as a DHCP server, and worse yet, I can't access the unit even if I hard code the IP on the PC being used for configuration.  I have to say that I feel kinda stupid having to post this, since I actually followed the documentation avaiable for this menial task and I fully expect the problem to be a simple one.  Namely, I am using two specific sources of info for connections.

View 20 Replies View Related

Netgear CVG824G - UnPn Device Accessible Via Public IP When On Internal Network Only

Mar 26, 2012

setup my Foscam IP cam lastnight on the Wireless network using UnPn and was able to access it fine via the public IP , using another PC on the same network with no issues. However when I tried to access it from work it doesnt connect - Is there a firewall setting that im overlooking?

FYI im using a Netgear CVG824G

View 1 Replies View Related

Dell :: Vostro 1500 And Cannot Connect To Wireless Network With Dell 1395 WLAN Mini-card

Jan 13, 2012

I have a Vostro 1500 and cannot connect to a wireless network with a dell 1395 WLAN minicard os XP home, what are possible solutions?

View 1 Replies View Related

Cisco Wireless :: WRVS4400N V2 Freezes And Is Not Accessible

Jul 14, 2009

I am having some problems with WRVS4400N v2.We use it just for wired network (wireless is not in use, but it is configured). As a WAN we use PPPoE. Most machines do not use DHCP.After a while (few hours to few days after power up) the router freezes and it is not accessible. I cannot ping it or access to the admin page.I have the latest firmware version (V1.00.09-ETSI)I also called service and they suggested to reset it to factory settings and reconfigure it.

View 3 Replies View Related

Linksys Wireless Adapters :: WET54GS5 Not Accessible After Inactivity?

Apr 15, 2012

I hadn't used this device (version 1) for a couple of years.  After that much time and many changes in my home network, once again I need it to connect a printer.  I pushed the reset button and followed the initial setup directions.  So far so good.
 
Then I followed directions for using it on my network.  Also good.  I can access the bridge's web server and I can send jobs to the printer.
 
My problem is, after a period of inactivity (say, over night) I can no longer access the printer or the bridge.  The only way I have found to get them back is to power-cycle the bridge. Some data ...
 
My router is a WRT320N.  It manages DHCP and reserves a fixed IP address for the bridge.The bridge connects to a wireless network managed by an Apple Airport Extreme 802.11.  It is connected directly to the router.  Yes, I have two WiFi networks.  No, I have not yet tried the bridge on the router's network.The LEDs on the bridge are the same, accessible or not.The printer is an OKI c3400n.

View 3 Replies View Related

Linksys Wireless Router :: E1200 Behind SonicWall Is Not Accessible

May 10, 2012

Here's what I have WAN->SonicWall->E1200 Basically the E1200 is given a static IP for it's WAN that is in the range of the Sonic Wall's DMZ interface, and the DMZ interface is the default gateway of the E1200.  When wireless clients connect to the E1200 they get internet access with no issues and they are on a separate network (which is intended).  The issue I have is if I get on a computer that is on the Sonic Wall's LAN network, which is able to route to the DMZ network, I am unable to ping the E1200 or perform remote management (turned on in the E1200).  There are phone devices that are on the DMZ network that I can ping from the LAN network.  I need to be able to remotely manage the E1200?

View 1 Replies View Related

Cisco Wireless :: WAP 4410n Not Accessible After Firmware Upgraded

May 26, 2011

I have a big problem with my cisco wap4410n .. I have upgrade the firmware of this AP to V2.0.3.3  for supporting multiple SSID after my upgradation is finished ..one time I can able to access the administration page But when I connected to another system the same AP I cannot able to connect through ethernet .The network connection in the system shows connected for one second and not connected for the next second its simultaneously repeating the same ..and still not connecting ..i changed my ip setting to default ie 192.168.1.xxxx and again to old config 192.169.3.xx any way the same instance is showing ..
 
In the WAP the power led, wireless led , are connected good but the Ethernet led is blinking off on stage.I have many times hard reset the WAP but off no use the same happens .i could not able connect to WAP.This may be the worse case ever seen in wap4410n …

View 1 Replies View Related

Cisco Wireless :: WAP2000 Admin Console Not Accessible?

Feb 13, 2011

I'm having an issue with our WAP2000 access point.  I had to reset the access point and now I can't access the admin console.  I've set a static IP address just as I did when I first set it up. Now when I browse to the 192.168.1.245 in my browser it just displays an Authentication error. 

View 1 Replies View Related

Linksys Wireless Router :: E1000 And E4200 Not Accessible Via HTTPS

Feb 2, 2012

2 linksys routers a E1000 (fw v2.1.02) and a E4200 (fw v1.0.03) aren't accessable via HTTPS. Both via LAN https://router-ip and via wan https://isp-router-ip:8080 . Both routers are configured correctly (allready did a rerstore to fact. defaults. while having a chat with linksys live chat support). Everything without a result.
 
Ie9 doesn't accept the linksys/cisco certificate. after the first warning ie9 just sais that it's unable to show the page .
 
I did some testing and found that it doesn't work with a win7 +IE9 (up to date updates) and also not on a win XP +IE8 (up to date updates), win XP +chrome (up to date updates).
 
And it works on a old image (virtual Pc) of WIN XP- IE6 (no up to date updates) and win XP(up to date updates) +firefox (older version) .
 
i tried to export the certificate using the xp-ie6 virtual pc. and import it else where, but that works within the lan. Over the WAN it's a " NO GO" . Is this a " Microsoft"   or a " linksys/cisco"  issue?

View 9 Replies View Related

Linksys Wireless Router :: WRT54GS Ver.6 - EBay Website Not Accessible

Jan 22, 2012

I am no longer able to access the "EBay" website while working on my wireless router. I have 3 personal computers, a laptop, 3 android smartphones & 2 ipod touch's. They all work fine, from my wireless router.I have the WRT54GS ver. 6.
 
The problem started with not being able to access EBay. I called the EBay people. Then, I called my local Internet Service Provider. There were at least 10 phone calls, to each. Then, I called the Linksys people. The lady told me that I had an outdated router and that I needed to get a new one. Well, I had previously bought the most expensive one I could get, said it was for "optimum" movie & gaming from Cisco.

View 9 Replies View Related

TP-Link Dual-Band Wireless :: WRD3600 USB Storage Not Accessible?

Apr 26, 2013

Region : Australia
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :

I'm having difficullty configuring a USB hard drive to my WDR3600

The WRD3600 is acting as a switch with my netgear cable modem router as the DHCP server. The DHCP server on the WRD3600 is turned off. the WRD3600 is accessible on my home network and I can connect to attached wifi and Ethernet devices.

when I attach my WD USB hard drive, I can see the device on the WDR3600 web GUI USB settings page. The WD hard drive service status is started and enabled. when I click on the open the disk link, nothing happens. When I try to access the 192.168.x.x/volume1 address, I get a page that says the username or password is incorrect.

When I disconnect the WDR3600 from the rest of my network and turn the DHCP server back on and connect directly to the router, i am able to access the connected usb hard drive.

is it possible to have the WDR3600 acting as a switch with DHCP server off and still access usb devices connected to it?

View 5 Replies View Related

Linksys Wireless Router :: E4200 Disk Is No Longer Accessible

Jul 19, 2011

I have connected a Seagate Free Agent 500GB to the USB port of my E4200 and while it does work fine, When the drive has been idle for a while, it goes into power saving mode, turning the spindle motor off. This means it takes a few seconds to access the disk. Not a problem, but apparently, those few seconds are enough for either Windows or the E4200 to decide that the disk is no longer accessible. The share is still available, but I get missing folders and files, files won't open or are not found, and backups job with Acronis True Image will fail because it thinks the share is unavailable.Sometimes, constantly refreshing the view and opening files at random will revive the share, but often, the only way to get it back is to restart the computer.
 
The problem is definitely related to the power saving. If I leave a video clip playing or similar, so there's always some disk access preventing the drive from entering power save mode, it works fine. But 15-20 minutes of no disk activity immediately causes problems.

View 3 Replies View Related

Cisco :: 1240 AP / 4402 WLC - VLans To Be Accessible To Wireless Devices

Sep 27, 2012

We have four VLANs that need to be accessible to wireless devices. The VLANs serve the following groups: staff, student, guest, phone
 
We are currently using a WEP/MAC authentication for staff and phone wireless networks.
 
I am looking for what your recommendation would be to provide reasonable level of wireless security, particularly with the staff network, but at the same time not require a high level of management, ex. managing active and inactive MAC addresses for MAC authentication. We have the following components available - 1240 APS, Windows AD, a 4402 WLC, and 6 campuses, and outdated Cisco ACS.We need to provide connectivity to Cisco wireless phones, laptops, iPads, cell phones.

View 2 Replies View Related

TP-Link Dual-Band Wireless :: TL-WDR4300 / USB File Sharing Not Accessible When Password Protected

Feb 13, 2013

Region : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP :

Firmware Version:
3.13.23 Build 121225 Rel.37950n
Hardware Version:
WDR4300 v1 00000000

Since I upgraded to the latest firmware I can only use the USB storage sharing when "Access shared storage with password" is left UNCHECKED. If I check the box I can no longer see the storage shares in Windows 7. I have also tried "\tploginlink.net" in the Run box, and it connects but shows me no mounted volumes. Also, Is it possible to set up more than two user accounts in addition to "admin" and "guest"?

View 2 Replies View Related

Dell :: Connection/Network Manager Not Listing Internal Modem (Dell XPS L502X)

Nov 1, 2012

I recently install Windows8 Enterprise build 9200 on my Dell XPS L502X and everything is working fine so far except my modem. In device manager its installed properly but the network manager doesn't list it as an option to connect to (as it usually would in win7),

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved