Linksys Wireless Router :: E1000 And E4200 Not Accessible Via HTTPS
Feb 2, 2012
2 linksys routers a E1000 (fw v2.1.02) and a E4200 (fw v1.0.03) aren't accessable via HTTPS. Both via LAN https://router-ip and via wan https://isp-router-ip:8080 . Both routers are configured correctly (allready did a rerstore to fact. defaults. while having a chat with linksys live chat support). Everything without a result.
Ie9 doesn't accept the linksys/cisco certificate. after the first warning ie9 just sais that it's unable to show the page .
I did some testing and found that it doesn't work with a win7 +IE9 (up to date updates) and also not on a win XP +IE8 (up to date updates), win XP +chrome (up to date updates).
And it works on a old image (virtual Pc) of WIN XP- IE6 (no up to date updates) and win XP(up to date updates) +firefox (older version) .
i tried to export the certificate using the xp-ie6 virtual pc. and import it else where, but that works within the lan. Over the WAN it's a " NO GO" . Is this a " Microsoft" or a " linksys/cisco" issue?
View 9 Replies
ADVERTISEMENT
Oct 12, 2012
This problem just started. I am unable to load certain https sites (for work). If i directly connect to ethernet, it works, so my isp isnt my problem. When i try to connect to the sites, it says "sending request" then times out. I have played around with the settings non stop and nothing has worked. I have a mac running 10.7.5.
View 3 Replies
View Related
Jul 19, 2011
I have connected a Seagate Free Agent 500GB to the USB port of my E4200 and while it does work fine, When the drive has been idle for a while, it goes into power saving mode, turning the spindle motor off. This means it takes a few seconds to access the disk. Not a problem, but apparently, those few seconds are enough for either Windows or the E4200 to decide that the disk is no longer accessible. The share is still available, but I get missing folders and files, files won't open or are not found, and backups job with Acronis True Image will fail because it thinks the share is unavailable.Sometimes, constantly refreshing the view and opening files at random will revive the share, but often, the only way to get it back is to restart the computer.
The problem is definitely related to the power saving. If I leave a video clip playing or similar, so there's always some disk access preventing the drive from entering power save mode, it works fine. But 15-20 minutes of no disk activity immediately causes problems.
View 3 Replies
View Related
Oct 22, 2011
Just upgraded my E4200 to firmware 1.0.03 (from 1.0.01). I have some new issues, questions, and some outstanding issues.
1) Web interface over https is now painfully slow.
2) Does DDNS work in bridge mode? DynDNS allows the sending of an update without an IP address, so it should be able to work.
3) Does accessing the management interface in bridge mode count as local or remote?
4) I'd really like to be able to get WOL working through the router. I managed to create a static DHCP reservation for 192.168.1.254 to ff:ff:ff:ff:ff:ff, but I don't think the router added that entry to the ARP table, is there any way to do this.
(I think have WOL forwarded to 192.168.1.254). 5) Should the router be providing some local dns hostnames? For example I have the device name set up in the local network setup, but it won't resolve. Similar for connected devices, especially those with with a DHCP reservation. 6) In bridge mode, does it matter which port is used to connect to the other network device? Does it have to be the WAN port?
View 6 Replies
View Related
Mar 16, 2013
Any benefit to enable https with in the gui instead of using the default http?
View 1 Replies
View Related
May 10, 2012
Here's what I have WAN->SonicWall->E1200 Basically the E1200 is given a static IP for it's WAN that is in the range of the Sonic Wall's DMZ interface, and the DMZ interface is the default gateway of the E1200. When wireless clients connect to the E1200 they get internet access with no issues and they are on a separate network (which is intended). The issue I have is if I get on a computer that is on the Sonic Wall's LAN network, which is able to route to the DMZ network, I am unable to ping the E1200 or perform remote management (turned on in the E1200). There are phone devices that are on the DMZ network that I can ping from the LAN network. I need to be able to remotely manage the E1200?
View 1 Replies
View Related
Jan 22, 2012
I am no longer able to access the "EBay" website while working on my wireless router. I have 3 personal computers, a laptop, 3 android smartphones & 2 ipod touch's. They all work fine, from my wireless router.I have the WRT54GS ver. 6.
The problem started with not being able to access EBay. I called the EBay people. Then, I called my local Internet Service Provider. There were at least 10 phone calls, to each. Then, I called the Linksys people. The lady told me that I had an outdated router and that I needed to get a new one. Well, I had previously bought the most expensive one I could get, said it was for "optimum" movie & gaming from Cisco.
View 9 Replies
View Related
Feb 1, 2013
I am experiencing one, possibly two problems with the X3000, firmware release v1.0.03:
1. When enabling guest mode, the internal network is not accessible via WLAN even for clients NOT connected via guest mode but regularly: Even non-guests but regularly connected clients can't access any internal IP but the router itself. netscan shows only the very client's IP and the router's. Only after switching guest mode entirely off, regularly connected clients can access interal IP again. netscan correctly shows the whole network. Obviously a firmware bug. BTW: Clients connected via cable do not experience this problems.
2. I am not sure about this, but after using the firmware built in "Reboot" button, the router reboots correctly. But for some reason, it is instable afterwards. It is operational for a few seconds but then reboots again. It keeps cycling. I could stop it by switching the router off and on again.
View 6 Replies
View Related
Nov 15, 2012
I need to get to my web admin page, but I cannot get into my router to do so.
IE tells mt that there is a certifacte error, and then gives me the option of going in anyway.
When I select that option, nothing happens, and the same IE warning page remains.
I am plugged directly into an e-net port on the router, and it is a WRT160N.
View 6 Replies
View Related
Mar 2, 2013
I have an issue with new Win8 & IE10. When I try to access web management interface of my wrt160nl (Firmware Version: 1.00.01 B15) via HTTPS I'm receiving the foolowing message:"Continue to this website (not recommended)." If I click on it another error page appears:"Certification error: Navigation blocked. There is a problem with this website's security certificate"
At the same time I'm able to acccess the management interface via HTTPS, but from my laptop with Win7 & IE9. There if I click on the red Certificate Error > View certificate and the certificate information is:Issued by: Linksys Issued to: Linksys Valid from : 1.1.2009 to 1.1.2010
So I'd like to know if I could update the router certificate or what settings should I use in IE10 in order to access the web management interface via HTTPS?
View 9 Replies
View Related
Feb 5, 2013
I tried to block youtube and facebook https in my router WRT610 V1 but the router fails blocking these websites. But, it does work for blocking youtube and facebook http.
View 9 Replies
View Related
Feb 29, 2012
I can not access my Linksys E3000 router via https://192.168.1.1.Before this mishap, I was able to gain access to my Linksys E3000 router via http://192.168.1.1 and/or the Cisco Connect software application on Windows 7. Yesterday, I went into my router's administration page and disabled http, and enabled https. I then closed out all browsers, restarted them and entered https://192.168.1.1
After that, I learned quickly I made a huge mistake to make these changes. I simply can not access my router admin wired or wirelessly. Accessing the internet works great, but router admin page is a no go.Firefox and IE states, "There is a problem with this website's security certificate." and was unable to proceed.Firefox even gave me the option to accept a security exemption to proceed, but that failed.
I have also tried using the Cisco Connect utility, and that also failed. I have taken these steps and not been able to access my router's admin page.I don't want to take the last final resort to reset my router and re-enter my settings again. I know I saved the router's backup file somewhere, but can't find it.Is there another way for me to gain access via https with http disabled? All I want to do now is go back in and change it back to enable http access.
View 9 Replies
View Related
Jan 28, 2012
To improve the security of my 4200 v1 router, I turned on in the router configuration "Access via HTTPS" and after the reboot I could not access my router via the browser even when I click on the browser message to continue. What do I need to configure either in the router or my browser to use HTTPS?
View 9 Replies
View Related
Oct 6, 2011
here comes the incident description: WRVS4400N breaks established VPN session if I am trying to connect to any LAN host via HTTPS.
View 1 Replies
View Related
Feb 16, 2012
I was unable to access the web admin on my WRT160n v3 w/ latest firmware this morning. Reset config to defaults & was able to get in. Enabled HTTPS access & disabled HTTP access & was right back where I started; reset to defaults again & left both boxes checked. Can access via HTTP, but HTTPS requests get refused/reset.
The reason I needed access was that when I booted up my laptop this morning, my wireless card wasn't picking up an IP address via WIFI, only worked via ethernet, so I need to see what was going on there — several reboots of the router didn't fix, nor has it fixed the HTTPS access problem described above.
View 6 Replies
View Related
Nov 23, 2012
bought EA4500 router and successfully installed. The configuration of the desktop i use is - Windows 7 Home Premium SP 1, IE 9.0 and Chrome -23 Dual core Pentium, 2.5 GHZ, 2GB RAM Issue - Many websites, perticularly secured (HTTPS) are not opening up with new router. (Net banking, yahoo mail etc) I didn't face any issue with my old router which is WRT54GH, it is quite old router and did work excellent and working also. I had two calls with CISCO support team, they did check everything and came to conclusion that the issue is with router and asked to get it replaced. I did that but facing same issue. This time i connected my friends laptop to EA4500 along with my personal desktop. My company laptop has following configuration - Windows 7 Enterprise, IE 8.0 Dual core Pentium, 2.67 GHZ, 2GB RAM I tried yahoo mail, net banking websites on my desktop and friends laptop, these websites didn't open in my desktop but no issues faced on friend's laptop. I also noticed that cisco, apple sites are not opening on my desktop but no issue on friends laptop. I tried same thing with my old router WRT54GH, and all sites opened on both the PCs.
View 9 Replies
View Related
Jul 13, 2012
I'm having wrt610n and there is an issue, i can login to the config page via http, but using the same computer i'm not able to login there via https but the same time i can login via ipad and the other computer, using the https.i even tried to reset the router settings, but the result was the same, so what PC option can cause it?
View 6 Replies
View Related
Dec 11, 2012
I want to block [URL] from Firmware parental control. But it does NOT work. It works on http site but not the https site.
E3200 Firmware
05/17/2012
Ver.1.0.04 (Build 1)
View 9 Replies
View Related
Mar 29, 2013
I am trying to log into my WRT610N version 2.0 Router admin page 192.168.1.1 using the secure HTTPS://192.168.1.1 protocol I have the router local management setting to allow both http and https access login:192.168.1.1/Management.asp I am using Microsoft IE version 10 and Firefox version 19.02 and latest Chrome browsers and none of them will work using the HTTPS protocol.This used to work in the past using older versions of the browsers though I would see a certicificate error warning.I have 2.00.01 build 15 firmware installed and I already tried reseting the router. Perhaps the router needs new firmware update to handle this with the latest browsers?
View 6 Replies
View Related
May 6, 2012
How to get HTTPS to work for local or remote management? Selecting HTTPS for either local or remote doesn't enable HTTPS for me. It still use HTTP.
View 2 Replies
View Related
Mar 8, 2012
When accessing the E3200 router using then ERROR 501.Not Implemented.That method is not implemented. The error occured after enabling the "Local Management Access, Access via: HTTPS" option on the Administration > Management tab.I tried different browsers FireFox (version 10), Internet Explorer (version 8,9), the same error was displayed and no acces granted to the E3200 router. I reseted the router and tried the latest firmware 1.0.03 build 9 Feb 1, 2012, but after enablib the option the issue occured again and it is not possible to connect to the router.
View 9 Replies
View Related
Mar 26, 2012
I own a E1000 router that I use with several wireless machines. Unfortunately, I cannot connect to the configuration of the router by typing url...in a browser, be it wireless or weirdly. For example, Firefox displays "Connection has been reinitialized". Furthermore, when I launch Cisco Connect, it only shows the error "Unable to connect to router". I tried to switch my router off and on, but that doesn't work. Totally resetting the router solves the problem, but not definitely.Is there a solution that does not require resetting my router?
View 2 Replies
View Related
Dec 20, 2011
My guest can't use my wireless network and I can not add more devices like a ipad2. Got a new ipad2 for my son for Christmas been trying to set it up for Christmas, so on Christmas day I am not trying to do the set up. My problem is I can not get it to log on to the network. I have been putting in the same pass word all my other computers in the house use but it will not work...
View 2 Replies
View Related
Feb 10, 2013
My wireless router (E1000) was accidentally unplugged. Since then the wireless LED light doesnt come on and the router cannot be detected. All the other lights are on. I tried to reset it but I dont think it worked, since the power LED didnt blink as its supposed to do after holding reset for 10-15 seconds (or more!!).
View 5 Replies
View Related
Aug 9, 2011
I've been using the E1000 for months. I have 2 iphones, an ipod, a windows 7 netbook and a macbook connected wirelessly to it. It's been set at wpa2/wpa mixed mode all this time without a problem. Out of the blue: no wireless connection on any device. I restarted the modem, router, PC's, phones, etc. I've updated the firmware. The only way I can get a wireless connection is to use wep. How can I get the better security and speed of wpa2 back?
View 4 Replies
View Related
Feb 21, 2012
I am trying to access the internet with my ipod and it is picking up my wireless connection but it is asking for a password, how do I get my password. I don't remember seeing a password when I hooked up my router several months ago. I called Cisco for some technical support but they wanted money to get me and I am not paying them a dime.
View 1 Replies
View Related
Jul 3, 2012
I can setup my router with the cd
View 1 Replies
View Related
Jul 26, 2010
I have a PS3, and i play allot of video games such as all COD game especially MW2. It says i have a strict or moderate NAT. My router is in the same room as the PS3, so i should have a Open Nat.Also i have another question, i bought this Epson printer from Best Buy, i was wondering if I can connect to it Wireless, but i think i cant connect to it wireless cause i dont see the WiFi Certification on the printer or anything hints that it can connect wireless
View 9 Replies
View Related
Sep 3, 2011
With the E1000 tthe wireless devices they seem to work just fine, I can access the internet just fine.
For my desktop PC in oder to use the router to get on the internet or to even use the Cisco Connect to check the router, the E1000 needs to be rebooted. I am unable to access the router otherwise. I have tried 3 different LAN cards all with the same results.
The latest firmware notes do not look like upgrading the firmware will work. My Router info from Cisco connect
Model name: Linksys E1000
Model number: E1000
Serial number: CVN21L422937
Firmware version: 2.1.01 build 5
Operating system: Windows 7 SP 1
Software version: 1.3.11006.1
Connection type (WAN): unknown
View 1 Replies
View Related
Jan 24, 2013
Things seem to slow down significantly to the point of loosing connectiviety. When I check, my mips are 150 or so. Tried disconnecting and connecting again but didn't work. When I power down the router and power it up, I get 300 mps again but doesn't last too long
View 2 Replies
View Related
Dec 30, 2011
A lady gave me E1000 along with an IMB Thinkpad because her husband was the main user on the internet. I have an intel iMac 10.4.11, DSL. I have not yet connected to either device via the router. I am new to wireless routers. I have been to the configuration page
View 2 Replies
View Related
Apr 7, 2013
I have a Linksys E1000 router which was working fine. My hard drive crashed; I replaced the hard drive and now my router is not recognized. I have reset it and tried to reinstall it with the CD. Nothing works.
View 1 Replies
View Related
Jun 23, 2011
I had an E1000 for a couple of years that worked OK. Then it went nuts--sporadically dropped the signal, wouldn't show its web page, etc.--maybe a power surge, who knows? So I tossed it and got a new one on the theory that it would be a plug in replacement .The new unit had a good signal, but also wouldn't show its web page, so I couldn't configure security. I removed Network Magic and everything else I could see pertaining to the old unit. However, the CD for the new unit still gives me: " Your router has already been set up. You need to use an Easy Setup Key that you can use to get other computers connected." Needless to say, I don't have such a thing. Cisco Connect is not installed at this point, so I can't go into it to create one.How can I purge the remains of the old unit so the new one will install properly?
View 6 Replies
View Related