Linksys Wireless Router :: E3200 Error 501 After Enabling Access Via HTTPS Option
Mar 8, 2012
When accessing the E3200 router using then ERROR 501.Not Implemented.That method is not implemented. The error occured after enabling the "Local Management Access, Access via: HTTPS" option on the Administration > Management tab.I tried different browsers FireFox (version 10), Internet Explorer (version 8,9), the same error was displayed and no acces granted to the E3200 router. I reseted the router and tried the latest firmware 1.0.03 build 9 Feb 1, 2012, but after enablib the option the issue occured again and it is not possible to connect to the router.
View 9 Replies
ADVERTISEMENT
Dec 7, 2011
I have Verizon FiOs and their provided wireless router does not cover my entire house. There are plenty of dead spots throughout the house (house is 3500sq. ft.)
The FiOS comes into the basement so currently I have their router is set up in the basement. I wanted to shut off their FiOS wireless router and use my new E4200 router for wireless coverage. I am pretty sure the E4200 alone will not be able to handle my house. Most of the rooms of the house are already prewired with Ethernet cables. All those wires converge in the same closet in the basement, therefore moving the router is not an option. I was thinking of putting whichever product you experts recommend in my office which is on the 2nd floor on one side of the house. This room does have Ethernet access. However it is currently at 50-60% signal (with FiOS). My bedroom which is on the opposite side of the house is at 10-20% signal (with FiOS).
I am looking to buy something to reach all the deadspots and have WIRED LAN access (if need be in the future). What is my best option? I have researched the RE1000, the WAP610N, and even some of the other routers (E2500 or E3200) for hours. I am not an expert, and frankly after hours of reading, these technical terms of "range expanding" and "access points" are all sounding synonymous to me. I guess what I need is the range expansion on the same WiFi SSID my E4200 will provide (to cover all areas of my house), as well as an access point for connecting TVs, Xbox, or PCs in the future.
1) RE1000
2) WAP610N
3) or a router to use as an access point/range expansion combo? E2500 or E3200?
Naturally, is the range capability better for Routers or the WAP610N or RE1000?
View 1 Replies
View Related
Dec 11, 2012
I want to block [URL] from Firmware parental control. But it does NOT work. It works on http site but not the https site.
E3200 Firmware
05/17/2012
Ver.1.0.04 (Build 1)
View 9 Replies
View Related
Nov 2, 2011
I've recently installed a certificate on my ACS 1113 appliance and in the Admin setup enabled management access over HTTPS. Since then I've not been able to access the GUI console. I have done some troubleshooting and I'm fairly certain that I have a certificate issue as Firefox gives me the error: Certificate type not approved for application. (Error code: sec_error_inadequate_cert_type)when I try and connect. So I want to either reconfigure the management access to use just HTTP or remove the certificate. I have logged on to the serial console and there are no options her to do this. The RADIUS and TACACS functions are working correctly - I just can't logon via the GUI.
View 1 Replies
View Related
Jun 17, 2011
I had Cisco Connect and USB printing off of the E3200 working, but now I'm getting an error and cannot print to HP Laserjet P1006 on my E3200's USB port. Cisco Connect has an error: Error code: 80004005 Model name: Linksys E3200 Model number: E3200 Serial number: Firmware version: 1.0.01 build 3 Operating system: Windows 7 Software version: 1.4.11145.0 Connection type (WAN): DHCP IP address (LAN): 192.168.0.253 IP address (WAN): 192.168.2.100 Computer IP address: 192.168.0.149
View 9 Replies
View Related
Jun 14, 2012
Access Restrictions option does not exist on my WRT160Nv3 Broadband Router Setup Page and I need to use that option.
View 2 Replies
View Related
Feb 29, 2012
I can not access my Linksys E3000 router via https://192.168.1.1.Before this mishap, I was able to gain access to my Linksys E3000 router via http://192.168.1.1 and/or the Cisco Connect software application on Windows 7. Yesterday, I went into my router's administration page and disabled http, and enabled https. I then closed out all browsers, restarted them and entered https://192.168.1.1
After that, I learned quickly I made a huge mistake to make these changes. I simply can not access my router admin wired or wirelessly. Accessing the internet works great, but router admin page is a no go.Firefox and IE states, "There is a problem with this website's security certificate." and was unable to proceed.Firefox even gave me the option to accept a security exemption to proceed, but that failed.
I have also tried using the Cisco Connect utility, and that also failed. I have taken these steps and not been able to access my router's admin page.I don't want to take the last final resort to reset my router and re-enter my settings again. I know I saved the router's backup file somewhere, but can't find it.Is there another way for me to gain access via https with http disabled? All I want to do now is go back in and change it back to enable http access.
View 9 Replies
View Related
Jan 28, 2012
To improve the security of my 4200 v1 router, I turned on in the router configuration "Access via HTTPS" and after the reboot I could not access my router via the browser even when I click on the browser message to continue. What do I need to configure either in the router or my browser to use HTTPS?
View 9 Replies
View Related
Nov 14, 2011
Purchased E3200 and did simple setup via CD setup (Cisco connect). Set up main name and password. Cisco Connect assigned "-guest" to end of main name for the guest account. Gave guest account its own password. Both main and guest accounts were broadcasting OK -- but guest account was not secure and could be accessed without password. (All software and firmware upgrades were done during initial setup).Reset the E3200 and restarted things from the CD setup. Created main account, main account password, and guest password again. In advanced settings, left basic wireless settings at initial settings, changed wireless secutiy to WPA2 Personal. Still having the guest account being broadcast in unlocked status. (Have turned off guest access for now until I can get password protection for it).
View 2 Replies
View Related
Apr 29, 2011
We're trying to connect our Linksys E3200 via ethernet wire to an existing company network that already has a router and switch - it will simply be connected to a port on our switch, and needs to function as an access point only (no DHCP, no routing, no NAT, etc.).
View 3 Replies
View Related
Jul 30, 2012
This is my second post today trying to fix the NAT types for my 2 xbox 360. I tried the port forwarding method but with this router when I enable the ports I lost internet access in my wired devices but my wireless devices still have internet access. I even lost internet access on my computer. I never had manu problems with a router trying to get my NAT type open on my 2 xbox.
View 6 Replies
View Related
Feb 16, 2012
I was unable to access the web admin on my WRT160n v3 w/ latest firmware this morning. Reset config to defaults & was able to get in. Enabled HTTPS access & disabled HTTP access & was right back where I started; reset to defaults again & left both boxes checked. Can access via HTTP, but HTTPS requests get refused/reset.
The reason I needed access was that when I booted up my laptop this morning, my wireless card wasn't picking up an IP address via WIFI, only worked via ethernet, so I need to see what was going on there — several reboots of the router didn't fix, nor has it fixed the HTTPS access problem described above.
View 6 Replies
View Related
Jan 31, 2013
When I try to enable remote management on my Linksys E3200 I get an "illegal value" message. Is there something else I need to change
View 2 Replies
View Related
Oct 6, 2011
I have setup an FTP site using the USB attached storage on my router. I would like to track when the site is accessed from the Internet. The logs don't show anything because the site is on the other side of the router. Is there a way to track activity to / from the site?
View 1 Replies
View Related
Oct 5, 2011
Is it possible to connect the E3200 Router to the internet over the wifi (WLAN) interface?Actually I can only use the ethernet port called "Internet" to connect with my Fritz Box router (which is responsible for my internet connection to my DSL provider).But I don't want to use 10m or more ethernet cable across my flat so it would be nice to use just wifi.
View 5 Replies
View Related
Feb 15, 2012
I have been trying to resolve what I think is an issue with DNLP or broadcast data getting to computers connected to my E3200. I have been wiresharking my network, trying different configuration, and scouring the web looking for an answer. My network is setup as shown below. The E3200 is on the same subnet and wired to the switch using the LAN port.DHCP is turned off. UPnP is enabled. DHCP is provided by the WRT54GL and turned off on the E3200.
WesternDigital has a program called "WD QuickView" and another called "WD Smartware" which together provide feedback about the drive status and real time backup capability (I prefer not to argue the +/- of these programs if folks don't mind <grin>). I have two computers on the wired LAN at the 16 port switch on which these programs work just fine. I get feedback about the drive status and backups occur. I also have two computers on the wireless LAN through the E3200 which DO NOT get feedback about drive status and appear not to detect the drive through the software. I CAN however access the drive by mapping it on Windows explorer for example.
With wireshark I do see chatter between the NAS and the E3200 (TCP traffic which I am not sure about...dpkeyserv stuff). I see broadcasts from the NAS to 239.255.255.250 often followed by talk between one of the wired computers and the NAS (which I am thinking is the comms for the WD...not sure though). I do not see chatter between wireless connected computers and the NAS (except for SMB or transferring files). It seems that the E3200 is not forwarding broadcasts to the computers connected to it even though it is connects as a switch.
View 7 Replies
View Related
Feb 24, 2012
how can a change my E3200 to a access point ? i have a wired router for my home network , connect to 2 x PC , NAS , printer. that works good , now i what to start up my wirless access piont . i standard configuration it is also a router . this wirless router is blokking my access to my NAS i think . i need to change it to a access point .
View 4 Replies
View Related
Jul 27, 2012
My E3200 (firmware 1.0.04) loses access to internet every week or so and OK again when reboot.
View 6 Replies
View Related
Dec 25, 2011
The issue is Windows7 (notebook ASUS N61Ja connected through Wi-Fi) loses and can not find again network HDD storage (Western Digital My Book Live 3TB). Rebooting of the notebook works but after I close HDD folder window the issue comes back. The issue exists only with Wi-Fi connection. Everything is fine using LAN connection.
View 1 Replies
View Related
Apr 26, 2012
I have enabled SSH on my 3750 switches and notice that https is not working. Iam not sure they are related but seems to be oddly coincidental. Therefore find it diffficult to monitor using CNA 5.7.6.
configs are given below
gvadc-sf01#sh run | i ip http
ip http server
ip http access-class 11
ip http secure-server
From my machine, i should normally have access to https running on the switch but isnt the case..
Do I need to generate a new crypto key separately for https?
View 5 Replies
View Related
Nov 12, 2012
I've reset my router, reinstalled Cisco Connect and didn't configure anything on parental controls.However, when I navigate to the "Access Policy" menu all I see is parental controls. I don't see any of the more sophisticated filtering menus like "access blocking policy", etc. I've attached a screenshot.
View 4 Replies
View Related
Jan 18, 2012
I am looking form accesspoint for home network. I do not need router and usb functionality, I have this already in my linux server. I need only wifi accesspoint with 2 bands and 300Mbps bandwith. Is there a big difference between E4200 or E3200 or E2500? I know that E4200 supports 450Mbps, but I am not planning to buy new devices which could go faster than 300Mbps. Beside of technical parameters in technical specyfication is there a difference in wifi bandwith or tranmission between wifi and cable network?
View 9 Replies
View Related
Nov 7, 2011
I finally decided to go with a e3200 yesterday and picked up one at Walmart. Last night I went to hook it up and had no luck setting it up. Now I have able Internet with a phone VoIP service. After trying to connect several ways, all the router wants to do is sit with a flashing power light. I cannot access the setup page wireless or wired and have tried several methods I found last night.
View 1 Replies
View Related
Aug 5, 2012
Is there a way to block keywords and also customize the default page given when access is restricted?
View 1 Replies
View Related
Dec 7, 2011
i have 2 rv042 with a vpn tunnel between them.the problem is that i can't access https over the VPN !if i telnet 192.168.10.1 443 through the VPN, it's not working either. if i telnet 192.168.10.1 443 in my 192.168.10.0 network it's working so it's reall the VPN tunnel the problem.
View 1 Replies
View Related
Mar 25, 2012
I just bought a brand new Linksys Cisco E3200 router. I set almost everything up in my house through the included software and went to port forward for some of my games. I realized I had something wrong with the ports and when I went back to access the ports through the web by typing in 192.168.1.1 which is the way I originally did the ports I could not. I then opened the software that came with the router and it could not detect the wireless network even though that is what I am using to type this now.
View 1 Replies
View Related
Oct 21, 2012
1552 E Ap with a 2504 WLC. Single Root Ap with Mesh the Mesh has the problem. Both Power Injector and AP has been replaced . How do you turn on the 802.11 B Radio? No other problems at 40 other sites with identical installation.
View 1 Replies
View Related
May 15, 2012
I had a E1200, I read the articles from the support about the routers, I think the "access Restrictions" has more flexible to setup on for the parental control, after chated to cisco support person online, I was told that the E1200 v2 has this "access restrictions" function, and I wan convinced to purchase from them. I did. I got the E1200 v2 recently, however, after I installed the CD and found there is no "access restrictions" tab, instead the "access policy" is still there. by the way the firmware is 2.0.02 now. How to get the "access restrictions" from setup? I've chatted with cisco support person twice again, but nobody can fix the problem, one suggested to restart and reinstall the CD. I uninstalled the software, restarted the computer and reinstalled the CD. same problem, no tab of "access restrictions".
View 6 Replies
View Related
Dec 22, 2011
Factory default settings of my WRT54GS encryption are Disabled. When I try to enable WPA Personal encryption (>Wireless, Wireless Security), it reverts back to Disabled as soon as I make the selection. >Administration, >Wireless, >Encryption Function is Disabled.When I had this router set up at another location with another ISP, this was never an issue. How do I get the encryption function to be enabled?
View 4 Replies
View Related
Jan 22, 2012
I upgraded my old Linksys wrt54g to the E1500. All the XP os are connected via cable and wireless connection, but the Vista laptop i get local access only connection error. This laptop used to connect on the older router using wep but with E1500 wpa-2 it cannot connect. I am unable to ping the router from the laptop wireless. Connecting ethernet cable it works fine and logging in as a guest works does too.
View 1 Replies
View Related
Aug 6, 2012
My router (WRT54GH) doesnt seem to be enabling the wi-fi network. Non of my devices are able to detect the wireless network.
View 1 Replies
View Related
Feb 28, 2012
I have the E4200 router, trying to change the security option to WEP to see if my WD TV live will connect to it, becuase right now with the WPA2 its not connecting.
I dont know why my WD TV live wont connect to the router, its visible in the list though!!
even my PS3 is having troubles connecting to the E4200 with the WPA2 security.
View 1 Replies
View Related
Sep 15, 2009
I was using WAP54G in our company in AP client mode to support "wired" connection to far workstation being part of Windows Domain (it needed network connection before logging to windows). It was working fine for a year, secured with WPA. this AP client was wirelessly connected to another WAP54G unit running regular AP mode.
Today was changing configuration on "AP client" , wanted to cvheck if WPA2 is supported while in AP client mode. well it wasn't, so ireverted the config back to what it was. after power cycle device stays in "bricked mode".
it doesn't boot up, LAN port inactive (like a cable unplugged), no WiFi, only 2 LEDs are lit permamently red POWER and yellow LINK. green ACT is dead. resetting is no luck, tried resetting it multiple times holding it with device powered on or off, tried 30/30/30 method, no luck.
finally took it apart (was out of warranty anyways) and shorted pin 16 (A18) on flash chip (Spansion) while powering up and it worked to the point when LAN interface becomes operational with 192.168.1.245 IP and i get ping response.
I thought that's it, would just re-load firware (original latest 3.04.03) and done. i was wrong. device takes fw via tftp, but immediately after tha it stops responding, green ACT never comes back online, reset still do not work. after power cycle LAN port is dead (as well as device) again. what has happened to it?
View 9 Replies
View Related
