Cisco :: 3750 - Enabling HTTPS While SSH Is Enabled
Apr 26, 2012
I have enabled SSH on my 3750 switches and notice that https is not working. Iam not sure they are related but seems to be oddly coincidental. Therefore find it diffficult to monitor using CNA 5.7.6.
configs are given below
gvadc-sf01#sh run | i ip http
ip http server
ip http access-class 11
ip http secure-server
From my machine, i should normally have access to https running on the switch but isnt the case..
Do I need to generate a new crypto key separately for https?
View 5 Replies
ADVERTISEMENT
Jun 29, 2012
I am getting this error on my PIX 535 with 8.0.4 code. The error is Error : OSPF/RIP cannot be enabled on failover interface, I am getting this error while trying to enable RIP on the firewall. The context is single mode and failover is enabled. When I am disabling the failover the Firewall is accepting the RIP configurations.
View 2 Replies
View Related
Nov 2, 2011
I've recently installed a certificate on my ACS 1113 appliance and in the Admin setup enabled management access over HTTPS. Since then I've not been able to access the GUI console. I have done some troubleshooting and I'm fairly certain that I have a certificate issue as Firefox gives me the error: Certificate type not approved for application. (Error code: sec_error_inadequate_cert_type)when I try and connect. So I want to either reconfigure the management access to use just HTTP or remove the certificate. I have logged on to the serial console and there are no options her to do this. The RADIUS and TACACS functions are working correctly - I just can't logon via the GUI.
View 1 Replies
View Related
Nov 9, 2011
I have got a TMG 2010 and i want to use Skype through it. if HTTPS inspection is enabled skype doesn't work, if it is disabled skype is working.What can i do for using Skype behind a TMG with httsp inspection so i want to use 8080 port only.I have excluded the 1 PC from HTTPS inspection or the destination URLs from HTTPS inspection.
View 1 Replies
View Related
Mar 8, 2012
When accessing the E3200 router using then ERROR 501.Not Implemented.That method is not implemented. The error occured after enabling the "Local Management Access, Access via: HTTPS" option on the Administration > Management tab.I tried different browsers FireFox (version 10), Internet Explorer (version 8,9), the same error was displayed and no acces granted to the E3200 router. I reseted the router and tried the latest firmware 1.0.03 build 9 Feb 1, 2012, but after enablib the option the issue occured again and it is not possible to connect to the router.
View 9 Replies
View Related
Nov 15, 2011
I recently installed an RV042 v1.1 vpn router (older hardware revision but using the latest available firmware 1.3.12.19-tm) and set up VPN access with the QuickVPN client. QuickVPN requires that the HTTPS setting be enabled under the Firewall options, so I did. I then scanned our static IP with grc.com's ShieldsUP! to check for open or non-stealthed ports and discovered that ports 80 and 443 show as wide open, while port 113 is closed but not stealthed. If I disable the HTTPS setting under Firewall, then ports 80 and 443 become stealthed. Is there any way to use QuickVPN and keep these ports stealthed?
View 1 Replies
View Related
Nov 5, 2012
I am really stuck in enabling ip routing though a simple task. I have configured 10 v LAN's in stacked 3750 switches have ip base image. I want to enable ip routing for inter V LAN communication but it is giving this error:
%COMMON_FIB-4-ISSUENCODEWRONGLEN: Message IPv6 global features, rev B for slots 2 (0x4) is wrong length (10, should be 7).
View 5 Replies
View Related
Mar 14, 2011
I've been trying to figure this out for some time now. I have a network setup with a couple of users, as well as a few servers. I'm using a 3640 as my border router that is connected to a 3750 with L3 routing enabled. I am using the IOS firewall in the 3640 and am having problems with downloads and connections in general on the LAN. Downloads will start at fast speeds (~1MB/s) but after a short time, it will begin slowing to a crawl or idle. I have disabled my ip inspect rules and found that the downloads will function at full speed for the entire download.
I've looked over the router configs several times, and I don't see anything unusual. Is there anything I should be looking for? I would like to think that this router can handle the traffic of about 5 computers.
View 16 Replies
View Related
Oct 20, 2009
I have a 3845 enabled for CDP connected to a stack of 3750 switches. From the router, i dont see any CDP neighbors. From the switch, i can see the router as neighbor. Why isn't the switch showing as a neighbor from the router side? [code]
View 3 Replies
View Related
Jan 3, 2012
I would like to apply a policy-based route on one of our L3 switches (Cisco 3750) to change the next-hop of a couple of servers only. The VLAN where those servers reside got WCCP enabled on it. When I want to apply the route-policy to that VLAN interface it doesn't let me. When I try to apply the same policy to a VLAN interface without WCCP it does work. Is there any Cisco IOS limitations that would prevent me from doing that?
Configuration:
route policy config:
access-list 70 permit ip host x.x.x.x (server IP)
route-map PBR1 permit 10
[Code].....
View 1 Replies
View Related
Nov 14, 2012
We have a 3750 acting as the core. By default IGMP snooping is enabled on cisco 3750 from the documents.but, when we see the ip mroute table on the switch, it doesnt show any output.
View 40 Replies
View Related
Jun 16, 2011
Configuring QoS on my cisco877W for VoIP below is the current config. [code]
View 3 Replies
View Related
Jan 21, 2013
I am setting up the DI-524 router with password protected. I tried to useWEP key is but after restart its going back to WEP disable mode.
View 3 Replies
View Related
Aug 9, 2011
I bought an 871w second hand with 124-24T IOS on it. I would like to enable QoS. When I use Cisco Configuration Professional to manage the router I click on QoS and it says it is not available. I know that the router itself is QoS capable.
This is my first time dealing with a router such as this and I wonder what I need to do to enable QoS.
View 1 Replies
View Related
Sep 27, 2012
Apparently one of my two ISPs,CenturyLink, supports 6rd connections to IPv6.
This is supported natively on my Q1000 ActionTec modem, however my modem is in "transparent bridging" mode, so that the RV042 v3 can be the only router.
how to configure the RV042 to operate in this manner.
Per the CenturyLink FAQ: the IPv6 address space is:
2602::0 /24
Most importantly, can I do this WITHOUT buying a new modem.
View 2 Replies
View Related
May 28, 2013
I'm having a problem with an ASA 5510 and software from Manage Engine (Firewall Analyzer). They are saying that sys log 113019 is not getting data over to the server where the firewall analyzer is installed. I'm checking the config and I see it enabled. Why this particular sys log info isn't making it to the reporting software when other data is.
View 4 Replies
View Related
Feb 13, 2013
how to enable the SFP module on cisco 2921?
View 3 Replies
View Related
Jan 8, 2012
I am using suddenlink intel pro/100 but my 1394 connection keeps enabling itself. this causes my screensaver webshots and my power options to quit working and computer shuts off on it's own. I disable 1394 connection in networks connections and then have to do a system restore to make things work right. A day or 2 later I have to do it all over again. It seems to have all started when I downloaded MS .Net framework 4.0 for a music program I don't really need. should I delete .net framework or is that a mistake.
View 5 Replies
View Related
Sep 23, 2012
Enabling TCP / IP connection between Windows CE 3.0 and PC?
View 1 Replies
View Related
Mar 12, 2012
RIPv2 And Disabling / re-enabling Interface
View 5 Replies
View Related
Dec 5, 2012
I am trying to test PIM SM mode between some 2811 routers built up in my packet tracer 5.3.3 .But surprisingly PIM option is not coming in the interface mode .Even IP multicast option is not shown in global config mode.
View 6 Replies
View Related
May 17, 2012
I have few inter-AS and Hub & Spoke MPLS L3VPNs up and running but, all of them uses plain IPv4 on the PE-to-CE connecting interfaces for switching the L3VPN customer traffic. While, this is ok to route traffic between customer sites over a ISP backbone using the VRF and MP-BGP/LDP configurations which does the MPLS forwarding in the ISP backbone, i would like to know, how to enable MPLS forwarding on the PE-CE links as well to make it MPLS right from CE1 - PE1 - P - PE2 - CE2 all the way for the VPN traffic.
This way, even the last mile access to CE devices will be an MPLS link over a Ethernet PHY so that, the traffic originating from CE1 to CE 2 will be carried on a MPLS tagged Ethernet frame instead of IPoEthernet frame.
View 7 Replies
View Related
Oct 25, 2011
I have an 881 router here in house and am attempting to enable the gui interface on the router.
I have tried the steps to enable http but have not had any success. Below is the IOS Version and the portion of the show config that reflects the http allow:
ROM: System Bootstrap, Version 12.4(15r)XZ2, RELEASE SOFTWARE (fc1)
Cisco 881 (MPC8300) processor (revision 0x100) with 249856K/12288K bytes of memory.
Processor board ID FTX1249Y16Q
[Code].....
View 4 Replies
View Related
May 26, 2011
Configured 6500 and 4500 to send netflow to a stealthwatch NADS.When visited by the stealthwatch engineer found that because i didnt have NDE configaured.i wasnt actually exporting any but the initial data in the flow.Now if i have got this right the command for this is - mls nde sender version 5
This is confirmed by looking at the following out put -show mls nde.Neither of these command work on my 4500 switch -does this mean that its not outputting all the data or do i not need to configure NDE or do i need another command ?
-4500 Sup V-10GE 10GE
-6500 Supervisor Engine 720 10GE
-or Supervisor Engine 720
View 0 Replies
View Related
Feb 28, 2011
We have downgraded cisco acs appliance 1120 from ACS 5.0 to ACS 4.2.1.15 , when we perform ICMP ping request to acs appliance its not responding , But i can do ping test from acs appliance on console mode not from GUI mode .
Is there any option to enable ICMP Ping response on cisco acs 1120 . else any patch to be upgraded to perform this action , my requirement is enable ICMP ping on acs appliance for troubleshooting . instead always check with telnet x.x.x.x 2002 for service responding
View 5 Replies
View Related
Mar 4, 2011
I currently have an ASA 5510 unit. I have a dmz setup which house some web servers and an inside interface. The web servers contain multiple public ip addresses which I have natted and access is fine.What is the most simple way to enable ping for my dmz from the outside. Meaning if someone outside the network pings one of the servers by its public ip address I would like it to respond to ping.
View 1 Replies
View Related
Jun 15, 2012
I need to connect 10 branches to a datacenter using cisco 861 routers because the ethernet sollution the provider gave us can't assign more than 32 MAC addresses for whe whole network. So we have all our servers at the datacenter with a central firewall/router and all remote branches with a static route to this router. We would like to make all branches local networks available through NAT or another better solution so network devices at the datacenter network can communicate with all local devices accross all the brances.
I've tried to set up a dynamic NAT from outside to inside the network and didn't work, set up static ip routes for both datancenter and remote branchs and also didn't work. I just would like to make the routers work in a transparent way, no blocking of anything, passing all traffic in and out the network.
View 7 Replies
View Related
Sep 20, 2012
I enable the IPS on the 2911 router . I am using the Basic IPS signatures that are inbulid on the routers . But sill it showing , that no signature is active .
ip ips signature-category
category all
retired true
ip ips signature-category
category ios_ips basic
retired false
[code]....
View 1 Replies
View Related
Mar 11, 2013
We have a pair of 4500s set up as HRSP pair. We have many VLANs set up. In one of the VLANs is a working Red Hat cluster which uses multicast for its heartbeats. The VLAN interface on each switch has ip pim sparse-dense-mode enabled on it. Multicast routing is not enabled.We now need to be able to send multicasts across a few VLAN to allow apple TV to work with our WLC and lightweight access points.
I assume I can just turn on multicast routing and enable ip pim sparse-dense-mode on the VLANs I need.Is this the case and will it have any effect on my current multicast traffic?
View 3 Replies
View Related
Nov 19, 2012
after installation of demo versions of 2900-SEC-TEMP & 2911-2921-SSLVPN-TEMP & rebooting the 2911 router I do not have access SSL commands.Show license indicates that 2900-SEC-TEMP & 2911-2921-SSL-TEMP licenses are active but NOT IN USE.
View 1 Replies
View Related
May 9, 2012
I'm running FW 1.02.01 (23) and I'm having problems with the DNS proxy. I have DNS Proxy enabled for my DHCP server on the router and I have my dns server programmed into the global dns location. I cannot ping any DNS names for my IPSEC VPN tunnel.
View 2 Replies
View Related
Apr 19, 2011
I have a 3g usb modem hooked up to my main Windows xp laptop. I'm also sharing that 3g connection with ICS out the ethernet port on the laptop to my wifi router.
All works ok and I'm able to browse from all computers connected to the wifi router except when I turn on the main laptop's wifi to connect to the same wifi router that it's connected to through ethernet for ics.
I am able to ping google and stuff and also use skype but I can't browse the web on any browser. If I turn off the wifi card on that laptop then I'm able to browse again with no problem on the main laptop and on all other connected computers.
I'm not sure but I'm guessing that the browsers are trying to connect through the wifi connection and no longer through the 3g usb modem?
The reason that I turned on the wifi connection of the main laptop to connect to the router is because connected to the router is also my security cameras dvr system and this way I can see my cameras on this main laptop.
So in other words, I have to turn off my main laptop's wifi connection to be able to browse the web but then I cant access the security system's dvr any longer.
My router's ip is 192.168.1.1
My dvr's ip is 192.168.1.100
My laptops' ip is 192.168.0.1
View 2 Replies
View Related
Sep 4, 2011
I have already successfully port forwarded my router and am able to connect to my mine craft server from anywhere on the Internet. Now id like to be able to remotely access my server from the Internet and install plugins or whatever. What are the basic steps to accomplish this? What port number should I use? Can I setup passwords so not just anyone can remotely connect? And can I limit which directories on the server's hard drive can be accessed remotely?
View 12 Replies
View Related
