Cisco WAN :: Enabling SFP Module On ISR 2921?
Feb 13, 2013how to enable the SFP module on cisco 2921?
View 3 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 2921 / How To Quit Service-module Session
Jun 9, 2012On 2921, how do you quite service-module session and get back to the router?
View 3 Replies View RelatedCisco WAN :: 2921 Router With Etherswitch Module Baud Rate Unsetting
Feb 14, 2013I have a 2921 router with 1 etherswitch module installed. I haven't done it before and was trying to change the baud rate to 115200 for installing an IOS on the etherswitch module which had been deleted. I ended up "unsetting" the baud rate on the etherswitch and rebooted. Now, when I try to session into the etherswitch, its opens the connection but I can no longer see any text on the screen. Im using Teraterm. I've tried different baud rate settings for my serial port in TeraTerm but still cant see any text on the screen. I dont know of any commands from the router prompt. Any suggestions to fix this? If can start seeing the text, then I can probably configure and set up the etherswitch module.
View 1 Replies View RelatedCisco WAN :: Enabling QoS In 877W
Jun 16, 2011Configuring QoS on my cisco877W for VoIP below is the current config. [code]
View 3 Replies View RelatedEnabling WEP On DI-524 Router?
Jan 21, 2013I am setting up the DI-524 router with password protected. I tried to useWEP key is but after restart its going back to WEP disable mode.
View 3 Replies View RelatedCisco Wireless :: Enabling QoS On 871W?
Aug 9, 2011I bought an 871w second hand with 124-24T IOS on it. I would like to enable QoS. When I use Cisco Configuration Professional to manage the router I click on QoS and it says it is not available. I know that the router itself is QoS capable.
This is my first time dealing with a router such as this and I wonder what I need to do to enable QoS.
Cisco Routers :: Enabling 6rd On RV042?
Sep 27, 2012Apparently one of my two ISPs,CenturyLink, supports 6rd connections to IPv6.
This is supported natively on my Q1000 ActionTec modem, however my modem is in "transparent bridging" mode, so that the RV042 v3 can be the only router.
how to configure the RV042 to operate in this manner.
Per the CenturyLink FAQ: the IPv6 address space is:
2602::0 /24
Most importantly, can I do this WITHOUT buying a new modem.
Cisco Firewall :: ASA 5510 - Enabling SYS Log ID
May 28, 2013I'm having a problem with an ASA 5510 and software from Manage Engine (Firewall Analyzer). They are saying that sys log 113019 is not getting data over to the server where the firewall analyzer is installed. I'm checking the config and I see it enabled. Why this particular sys log info isn't making it to the reporting software when other data is.
View 4 Replies View Related1394 Net Adapter Keeps Enabling Itself
Jan 8, 2012I am using suddenlink intel pro/100 but my 1394 connection keeps enabling itself. this causes my screensaver webshots and my power options to quit working and computer shuts off on it's own. I disable 1394 connection in networks connections and then have to do a system restore to make things work right. A day or 2 later I have to do it all over again. It seems to have all started when I downloaded MS .Net framework 4.0 for a music program I don't really need. should I delete .net framework or is that a mistake.
View 5 Replies View RelatedEnabling TCP / IP Connection Between Windows CE 3.0 And PC?
Sep 23, 2012Enabling TCP / IP connection between Windows CE 3.0 and PC?
View 1 Replies View RelatedCisco :: RIPv2 And Disabling / Re-enabling Interface
Mar 12, 2012RIPv2 And Disabling / re-enabling Interface
View 5 Replies View RelatedCisco :: Enabling PIM In Packet Tracer 5.3.3.0019?
Dec 5, 2012I am trying to test PIM SM mode between some 2811 routers built up in my packet tracer 5.3.3 .But surprisingly PIM option is not coming in the interface mode .Even IP multicast option is not shown in global config mode.
View 6 Replies View RelatedCisco :: Enabling MPLS Forwarding Over A PE-CE Link
May 17, 2012I have few inter-AS and Hub & Spoke MPLS L3VPNs up and running but, all of them uses plain IPv4 on the PE-to-CE connecting interfaces for switching the L3VPN customer traffic. While, this is ok to route traffic between customer sites over a ISP backbone using the VRF and MP-BGP/LDP configurations which does the MPLS forwarding in the ISP backbone, i would like to know, how to enable MPLS forwarding on the PE-CE links as well to make it MPLS right from CE1 - PE1 - P - PE2 - CE2 all the way for the VPN traffic.
This way, even the last mile access to CE devices will be an MPLS link over a Ethernet PHY so that, the traffic originating from CE1 to CE 2 will be carried on a MPLS tagged Ethernet frame instead of IPoEthernet frame.
Cisco Switching/Routing :: Enabling Gui On 881 Router?
Oct 25, 2011I have an 881 router here in house and am attempting to enable the gui interface on the router.
I have tried the steps to enable http but have not had any success. Below is the IOS Version and the portion of the show config that reflects the http allow:
ROM: System Bootstrap, Version 12.4(15r)XZ2, RELEASE SOFTWARE (fc1)
Cisco 881 (MPC8300) processor (revision 0x100) with 249856K/12288K bytes of memory.
Processor board ID FTX1249Y16Q
[Code].....
Cisco :: NetFlow Enabling On 6500 And 4500
May 26, 2011Configured 6500 and 4500 to send netflow to a stealthwatch NADS.When visited by the stealthwatch engineer found that because i didnt have NDE configaured.i wasnt actually exporting any but the initial data in the flow.Now if i have got this right the command for this is - mls nde sender version 5
This is confirmed by looking at the following out put -show mls nde.Neither of these command work on my 4500 switch -does this mean that its not outputting all the data or do i not need to configure NDE or do i need another command ?
-4500 Sup V-10GE 10GE
-6500 Supervisor Engine 720 10GE
-or Supervisor Engine 720
Cisco AAA/Identity/Nac :: Enabling ICMP On ACS 1120?
Feb 28, 2011We have downgraded cisco acs appliance 1120 from ACS 5.0 to ACS 4.2.1.15 , when we perform ICMP ping request to acs appliance its not responding , But i can do ping test from acs appliance on console mode not from GUI mode .
Is there any option to enable ICMP Ping response on cisco acs 1120 . else any patch to be upgraded to perform this action , my requirement is enable ICMP ping on acs appliance for troubleshooting . instead always check with telnet x.x.x.x 2002 for service responding
Cisco Firewall :: 5510 Enabling Ping For Dmz
Mar 4, 2011I currently have an ASA 5510 unit. I have a dmz setup which house some web servers and an inside interface. The web servers contain multiple public ip addresses which I have natted and access is fine.What is the most simple way to enable ping for my dmz from the outside. Meaning if someone outside the network pings one of the servers by its public ip address I would like it to respond to ping.
View 1 Replies View RelatedCisco WAN :: 861 Enabling All Internal Devices To Be Reachable Through NAT
Jun 15, 2012I need to connect 10 branches to a datacenter using cisco 861 routers because the ethernet sollution the provider gave us can't assign more than 32 MAC addresses for whe whole network. So we have all our servers at the datacenter with a central firewall/router and all remote branches with a static route to this router. We would like to make all branches local networks available through NAT or another better solution so network devices at the datacenter network can communicate with all local devices accross all the brances.
I've tried to set up a dynamic NAT from outside to inside the network and didn't work, set up static ip routes for both datancenter and remote branchs and also didn't work. I just would like to make the routers work in a transparent way, no blocking of anything, passing all traffic in and out the network.
Cisco Firewall :: Enabling IPS On 2911 Router?
Sep 20, 2012I enable the IPS on the 2911 router . I am using the Basic IPS signatures that are inbulid on the routers . But sill it showing , that no signature is active .
ip ips signature-category
category all
retired true
ip ips signature-category
category ios_ips basic
retired false
[code]....
Cisco :: 4500s / Enabling Multicast For Apple TV?
Mar 11, 2013We have a pair of 4500s set up as HRSP pair. We have many VLANs set up. In one of the VLANs is a working Red Hat cluster which uses multicast for its heartbeats. The VLAN interface on each switch has ip pim sparse-dense-mode enabled on it. Multicast routing is not enabled.We now need to be able to send multicasts across a few VLAN to allow apple TV to work with our WLC and lightweight access points.
I assume I can just turn on multicast routing and enable ip pim sparse-dense-mode on the VLANs I need.Is this the case and will it have any effect on my current multicast traffic?
Cisco Switching/Routing :: Enabling SSL-VPN On 2911
Nov 19, 2012after installation of demo versions of 2900-SEC-TEMP & 2911-2921-SSLVPN-TEMP & rebooting the 2911 router I do not have access SSL commands.Show license indicates that 2900-SEC-TEMP & 2911-2921-SSL-TEMP licenses are active but NOT IN USE.
View 1 Replies View RelatedCisco :: 3750 - Enabling HTTPS While SSH Is Enabled
Apr 26, 2012I have enabled SSH on my 3750 switches and notice that https is not working. Iam not sure they are related but seems to be oddly coincidental. Therefore find it diffficult to monitor using CNA 5.7.6.
configs are given below
gvadc-sf01#sh run | i ip http
ip http server
ip http access-class 11
ip http secure-server
From my machine, i should normally have access to https running on the switch but isnt the case..
Do I need to generate a new crypto key separately for https?
Cisco Routers :: SRP541w DNS Proxy Enabling
May 9, 2012I'm running FW 1.02.01 (23) and I'm having problems with the DNS proxy. I have DNS Proxy enabled for my DHCP server on the router and I have my dns server programmed into the global dns location. I cannot ping any DNS names for my IPSEC VPN tunnel.
View 2 Replies View RelatedCan't Browser The Web On 3g Modem After Enabling Wifi
Apr 19, 2011I have a 3g usb modem hooked up to my main Windows xp laptop. I'm also sharing that 3g connection with ICS out the ethernet port on the laptop to my wifi router.
All works ok and I'm able to browse from all computers connected to the wifi router except when I turn on the main laptop's wifi to connect to the same wifi router that it's connected to through ethernet for ics.
I am able to ping google and stuff and also use skype but I can't browse the web on any browser. If I turn off the wifi card on that laptop then I'm able to browse again with no problem on the main laptop and on all other connected computers.
I'm not sure but I'm guessing that the browsers are trying to connect through the wifi connection and no longer through the 3g usb modem?
The reason that I turned on the wifi connection of the main laptop to connect to the router is because connected to the router is also my security cameras dvr system and this way I can see my cameras on this main laptop.
So in other words, I have to turn off my main laptop's wifi connection to be able to browse the web but then I cant access the security system's dvr any longer.
My router's ip is 192.168.1.1
My dvr's ip is 192.168.1.100
My laptops' ip is 192.168.0.1
Enabling Remote Desktop Over The Internet?
Sep 4, 2011I have already successfully port forwarded my router and am able to connect to my mine craft server from anywhere on the Internet. Now id like to be able to remotely access my server from the Internet and install plugins or whatever. What are the basic steps to accomplish this? What port number should I use? Can I setup passwords so not just anyone can remotely connect? And can I limit which directories on the server's hard drive can be accessed remotely?
View 12 Replies View RelatedEnabling Wireless Connection Without Fn Button?
Feb 16, 2013My keyboard was broken so plugged in a USB keyboard that doesn't have a fn button. I must have accidentally pressed something as my comp is asking me to turn in the wireless capability. There is no button on the computer and the light for wifi is off. How to turn this back on with a keyboard that does not have a fn button?
View 1 Replies View RelatedD-Link DIR-600 :: Does Enabling SPI Affect The Performance
Dec 15, 2011I notice that SPI is disabled by default on the DIR-600 (in firmware 2.10 and 2.11 as well).Port forwarding still works with SPI on (use it for BitTorrent).So why is it off by default?Does it slow down things?
View 1 Replies View RelatedEnabling NAT Loopback On HG556a Router?
Jun 16, 2013This is one of the standard issue vodafone routers. So i set up web-server on my laptop, and it is accessible to the internet now.
However I need to be able to access it from my machine using the public address. But I just cannot find where to enable nat loopback. I looked for options in both regular and advanced user logins (web interfaces). So I suppose the last option is telneting into it, and using commands to do it.. but I don't know how to access it (cant find the credentials). URL
In above link it says that i can find this info in configuration file, but how to access it?
And then what commands should I use to enable the NAT loopback?
Cisco VPN :: RV180w - Quick VPN Stops After Enabling FMPIWP
Dec 26, 2012We use FileMaker Pro instant web publishing for several of our clients. I just installed the Cisco RV180w wireless N vpn router. As soon as I enabled the FileMaker IWP quick VPN stopped working.
View 0 Replies View RelatedCisco :: Enabling Net Flow In 2960 And 4948 Switches
Aug 26, 2012I am unable to input the command "ip flow-cache timeout active 1" to my cisco 2960 and 4948 switches. But i am able to do so in my cisco 6500 series switch. Hence how do i enable netflow on both 2960 and 4948 devices?My 2960 and 4948 are L3 switches. What commands or additional hardware module are required.
View 4 Replies View RelatedCisco Firewall :: Telnet Not Work After Enabling AAA On FWSM 3.2
Oct 7, 2011After enabling AAA FWSM lost opportunity telnet session. FWSM version 3.2(5). In the logs show that resets itself FWSM telnet session.
Conf.,aaa-server TACACS+ (management) host 192.2.151.111
key aaa authentication ssh console TACACS+ LOCAL
aaa authentication enable console TACACS+ LOCAL
aaa authentication telnet console TACACS+ LOCAL
[Code] .....
Cisco Switching/Routing :: Enabling Jumbo On 6509?
Jan 28, 2013does enabling jumbo frames on the 6509 require a reboot?
View 1 Replies View RelatedCisco Wireless :: Enabling Netflow On A 2504 Controller?
Feb 28, 2013I just completed setting up a AIR-CT2504-K9 controller with 9 APs with RADIUS on the private WLAN and an open guest WLAN; I want to enable netflow exports to a collector, but see no place in the GUI to do this and no obvious CLI commands.
View 1 Replies View Related