We use FileMaker Pro instant web publishing for several of our clients. I just installed the Cisco RV180w wireless N vpn router. As soon as I enabled the FileMaker IWP quick VPN stopped working.
View 0 Replies
I got : RV180W router updated with the last firmware.Static IP for the DMZ host (Synology Server 212+) My problem is that I had try all combinaison since 10 days to get IP source in synology interface (to block IP's of bad connections...) but, I only see the RV180W adress....So impossible to block bad connections IP.
View 3 Replies View RelatedI would like to ask if what is the difference between RV180W-E-K9-G5 and RV180W-A-K9-NA specifically the -E and the -A. As far as I know -A is the compliance code for Philippines. Am I right? If yes, what about -E? There is a documentation for wireless complaince on Aeronet devices but what about these SB products?
View 9 Replies View RelatedI need to setup a VPN into my home network ASAP.I have logmein so i can get in and setup a VM or something, but im not sure the best way to about this.I have TWC home
Internet---Modem---DlinkDIR-655 Router(no dhcp server)---Switch---network
I am running a 2008R2 DomainController/DNS/DHCP.I have hyper-v setup, so maybe a vm is easiest, just thought i would ask.Doesnt need to be super robust, this is a temporary solution.
For the life of me I can’t get my quick VPN client to connect to my Cisco 120w. I have IPSec gateway to gateway setup and working just fine. I made my quick vpn client under vpn tab. I enabled remote management. Every time I try to connect I get the failed to establish connection. Using the same quick VPN software I can connect to a rv082 with no trouble.
View 2 Replies View RelatedI have a WRVS4400N router & am using Quick VPN to connect to the Router. I can able connect through Window XP Machine, but not able to connect through Window Vista & 7. Whenever I try to connect through Window 7, I got this message: The remote gateway is not responding. Right now the Cisco router is behind DSL modem and I can't change the DSL modem to bridge mode as my ISP told me that we can't change DSL modem to bridge mode. what I have to do to connect to the router through Windows 7 & Vista.
View 3 Replies View RelatedI'm having issues getting QuickVPN to connect. I think it's an issue pinging the gateway but I'm not 100% sure. We are using Comcast Business, I have placed the RV180 in the DMZ. The setup looks like this: Internet -> Comcast router -> RV180 (DHCP) -> rest of network.
View 5 Replies View Relatedwe bought a router for our company RV042, so far good
What i did:
1. i created QuickVPN clients, droped in certificate which exported from router
******NOTE********All company's laptops are running: Windows 7pro 32bits****************
The users are connecting sucesefully to router and using resources from server etc...
But, when they press disconnect on quickVPN it shows disconnected, but when i log in into router, i still see that they are connected (not disconnecting),
and the problem is they cannot connect to router second time if i don't manually disconnect them from rv042 router....
Only sometimes the clients disconnect properly from router, but it is very very rare...
Question1: Where I should look for the problem in router rv042 or client laptops?
Question2: Does the 64bit windows7 pro OS can connect to RV042router?
I have latest quickvpn software and latest router firmware.
we recently bought a new desktop firewall solution from McAfee and I can't seem to get our VPN to work. I allowed QuickVPN in the firewall and additionally opened port 1194, 1720 and 1723 - but that does not do the trick. Once I turn off the firewall and use Windows Firewall instead it works.
View 2 Replies View RelatedI have a hub / spoke configuration, with about 9 spokes. All connect ot the main office over a VPN, all native Cisco routers (2900 series)I want to use netflow to monitor traffic, and I started, but my results are not what I expected. I don't think I configured it properly.
Several interfaces have sub-interfaces, so if I'm reading correctly, I only export flow from the physical intyerface, not the sub-interfaces. Correct?I want both inbound and outbound traffic, so do I use the command twice with ingress and egress?What is the difference between V5 and V9?
Finally, how does NBAR fit in this? I want to see applications as well as just packets.
I have a laptop and a desktop pc both connected to the same wifi network, both running win 7. File transfers are not quick enough for my liking over wifi so when I need to move a few files about I tend to hook the two together with an ethernet cable. When I try to copy a file however it defaults to using the wireless connection. I'm getting around this at the moment by just turning the wifi off on the laptop while I do the transfers but it would be nice to not have to.
View 1 Replies View RelatedPID VID : RV042 V03
LAN IPv4/ Subnet mask : 192.168.0.7/255.255.255.0
Working Mode : Router
[code]...
PPTP working fine but not with Quick VPN .. test on some computer and internet access still can not get connect to router.
Quick VPN and have not had any success connecting with our router. Below is my components info. Cisco router: WRVS4400N, Firmware V2.0.0.7. The router is behind a Comcast SMC business gateway modem Remote computer: Window 7 Ultimate 64 bit
I downloaded the Quick VPN client 1.4.2.1, and installed the client successfully but cannot connect using the VPN Client Account that I had set up in the router. Below are several questions that I hope to understand.
1) Do I need to configure specific ports for VPN in the Comcast gateway firewall?
2) What IP address do I put in the Quick VPN client profile when I connect remotely? The WRVS4400N modem shows 2 IP addresses in the Status:
DNS1: 68.xx.xx.176
DNS2: 68.xx.xx.132
Are these the IP that go into the "Server Address" on the Quick VPN client profile? and which one of the two? or do I use the static WAN IP address provided by my Comcast account?
3) In the Quick VPN client window, what is the "Use Remote DNS Server" mean?
4) Do I need to create a client certificate from the WRVS4400N for the client
5) Is there any setup needed for the remote firewall (if the client is behind a home wireless router and modem, for example)?
WRVS4400N v2.0 2.0.0.8
QuickVPN 1.4.1.2
Vista Home Premium SP2 64-bit
Trying to connect from laptop through an AP to my WRVS4400N via VPN. Not having much luck...I get to "Activating Policy..." and then "Connection Error".I like this router thus far, I have been able to set up multiple BSSIDs and VLANs which has been very useful.
One computer with two users. My account allows quick access but the other is dramatically slow. I created a new account and it has the same problem.
View 1 Replies View RelatedVery recently, we had implemented Site-to-Site VPN tunnel between two Linksys RV042 4-port VPN routers. Everybody in our remote site is accessing and sharing the data through this tunnel and it is working fine.
Now, we have a plan to implement the same for our mobile clients also. For this, we had followed all the basic configuration procedures and user got connected to Quick VPN tunnel. Here is a problem we had observed. The mobile client user is connected to the tunnel, but unable to access the office LAN from the PC.
If I am using an ASA5505, and I have a configuration similar to below, I see that the untrusted interface is only allowed to ftp to 192.168.1.5. Since the trusted interface is not limited to ftp only can it basically run any protocol it wants to 10.20.30.2, or does it get limited to only ftp by the other ACL on returning packets.Also, is the ACL applied to the interface because the ACL's name is the name of the interface?
View 2 Replies View Relatedany success using the stand on a WAP4410N? I have not been able to get them to snap into place as described in the Quick Start Guide.
Seems to be an extremely crude and very poorly implemented design. They fall off and the WAP frequently falls over. I expected much better from Cisco given the price.
Router is a version 1.1 running with sw version V1.1.13-ETSI
Quick VPN is sw version Ver 1.4.1.2
The issue is that I can't connect due to that i cant ping the internal IP, get this error message in the QVPN log [WARNING]Failed to ping remote VPN Router![URL]I have disable the "Block WAN Request" and it is possible to ping the router on the external site.So as I see it, the router blocks for ping on the internal IP via QVPN, what have I done wrong?
We have a need to access an VLAN at the main office( ie Core Switch 6500,switch 3750) from a remote site(Cisco3845 router, Switch3750) connecting by a SP through fibre link.
what is the easiest and quick way to do it and the user from the remote site just want to have access to that VLAN for a couple of days only.
Don't have CD. Where do I download this on Dlink site?
View 3 Replies View Relatedcan i share accouting software like Tally through quick vpn ? WRVS4400n has been configured on the site . and can connect to the site using quick vpn software without a problem . will Tally work ?
View 1 Replies View RelatedI have an RV042 using Quick VPN to connect to a remote network. I have port 1723 forwarded to a static IP address on a Windows 7 Pro 64 bit PC. I can establish the VPN and ping a printer but not the Win 7 PC. I can not acccess any shares on the pc via the IP address. It has Norton Antivirus and Windows Firewall. This remote PC replaced a Windows xp PC that allowed access to the shares. I have tried access with a Windows XP Pro and Windows Vista Home Premium PC. Neither have worked.
View 1 Replies View RelatedI've currently got a WRT54G and have an opportunity to buy a WRT54GS. The problem is that the seller of the WRT54GS has lost the Set-Up Wizard CD & Hard Copy Quick Installation Guide. Obviously I have these items already with my WRT54G. My question is this. Are these items different for the WRT54G or will the stuff I already have for the WRT54G "work" for the WRT54GS.
View 5 Replies View RelatedI have a couple Dell R710 2U servers that came with the Dell quick rails. The rack I am trying to place them in is a 4-post open cabinet, but the depth of the posts are about an inch too short to allow the Dell quick rails to snap-lock to the square holes. Are there any 2U extenders I can attach to the back two posts of the cabinet to give the minimum length needed for the Dell quick rails to snap-lock? The extenders would also need to have the square holes.
View 3 Replies View RelatedI have an RV042 setup for quick vpn access.The remote computer in question is a win 7 64bit. The PC uses McAfee SAAS firewall. This disables the windows firewall.
1. I can connect to the vpn with SAAS disabled and windows firewall enabled.
2. I cannot connect to the vpn with both windows firewall and SAAS disabled.
3. I cannot run SAAS and windows firewall together to check if this would work.
I need to figure out what windows firewall is doing to allow the vpn to connect, and so how do this with windows firewall disabled. I can then leave the windows firewall disabled and enable McAfee SAAS.The message quickvpn provides when it fails to connect is that the remote gateway is not responding. The client logs show that the tunnel had been opened but it was unable to ping.
Configuring QoS on my cisco877W for VoIP below is the current config. [code]
View 3 Replies View RelatedI installed the RV180W yesterday and decided to play with it a bit today. I got stuck on the firmware update. Tried different browsers on different PC's. Tried going to 1.0.1.9 first. I have the "reset all configurations" button checked. After looking through the posts here I'm not sure this firmware will even fix my next few problems(port forwarding etc). Is there a trick with this device?
View 4 Replies View RelatedI'm trying to make the VPN connection between two routers CISCO RV180w.I performed the basic configuration in cisco "server". I did the same in cisco "client".The following configuration and logs, do not know what to do ...
SERVER CONFIGURATION:
IKE Policy Configuration:
VPN Policy Configuration:
CLIENT CONFIGURATION:
[code]....
We have installed a fiber internet access and have the ONT from the provider already installed.We're trying to use the RV180W to use this internet connection. [code] So I need to configure the router with the .36 static IP on the WAN, and using the .37 gateway and the provided DNS servers. I also need that this WAN is tagged with VLAN ID 20. I'm only able to set VLAN ID on the LAN ports via the admin interface.
View 8 Replies View RelatedI am struggling to configure my new RV180w router to accept a VPN connection from my Apple computers.
I wish to use IPSec with Group and Pre-Shared Key authentication. The RV180 has just replaced my 800 series ADSL router and I want my remote clients to be able to connect using either the VPN client capability built into the OS X operating system or the Cisco VPN Client software installed on their Macs.
So far, using the RV180's web setup screens, I have created a VPN Policy and a corresponding IKE Policy was created as well. I couldn't see anywhere to include the 'Group' name. I have created a user but wasn't sure of which Protocol to use so I am trying XAUTH.
At the client end some people are connecting using Cisco's VPN Client software Download Software - Cisco Systems
Some people, with OS X 10.6 and above, are using the Mac OS X network built-in VPN client.
We all connected without a problem to the previous 800 series router using IPSec with Group authentication and Pre-Shared key.
i've installed the new firmware on my router and now the UC is showing 100% all the time. I've tried to factory reset it, it's doing the same thing. If I downgrade to previous firmware, it goes back to normal . I've only 1 PC in my network (test lab), so no big traffic here. is it a bug ?
View 1 Replies View RelatedI am setting up the DI-524 router with password protected. I tried to useWEP key is but after restart its going back to WEP disable mode.
View 3 Replies View Related
