For the life of me I can’t get my quick VPN client to connect to my Cisco 120w. I have IPSec gateway to gateway setup and working just fine. I made my quick vpn client under vpn tab. I enabled remote management. Every time I try to connect I get the failed to establish connection. Using the same quick VPN software I can connect to a rv082 with no trouble.
View 2 RepliesI'm having issues getting QuickVPN to connect. I think it's an issue pinging the gateway but I'm not 100% sure. We are using Comcast Business, I have placed the RV180 in the DMZ. The setup looks like this: Internet -> Comcast router -> RV180 (DHCP) -> rest of network.
View 5 Replies View RelatedPID VID : RV042 V03
LAN IPv4/ Subnet mask : 192.168.0.7/255.255.255.0
Working Mode : Router
[code]...
PPTP working fine but not with Quick VPN .. test on some computer and internet access still can not get connect to router.
Quick VPN and have not had any success connecting with our router. Below is my components info. Cisco router: WRVS4400N, Firmware V2.0.0.7. The router is behind a Comcast SMC business gateway modem Remote computer: Window 7 Ultimate 64 bit
I downloaded the Quick VPN client 1.4.2.1, and installed the client successfully but cannot connect using the VPN Client Account that I had set up in the router. Below are several questions that I hope to understand.
1) Do I need to configure specific ports for VPN in the Comcast gateway firewall?
2) What IP address do I put in the Quick VPN client profile when I connect remotely? The WRVS4400N modem shows 2 IP addresses in the Status:
DNS1: 68.xx.xx.176
DNS2: 68.xx.xx.132
Are these the IP that go into the "Server Address" on the Quick VPN client profile? and which one of the two? or do I use the static WAN IP address provided by my Comcast account?
3) In the Quick VPN client window, what is the "Use Remote DNS Server" mean?
4) Do I need to create a client certificate from the WRVS4400N for the client
5) Is there any setup needed for the remote firewall (if the client is behind a home wireless router and modem, for example)?
I have the RV 120W router, and can not seem to get SNMP Set to work. I though I would just check here, and make sure it is supported, and if it is, are there any special config settings I need to use?
View 2 Replies View RelatedI am interested in the QuickVPN solution for a Mac.I am getting mixed messages in my searches.If not, what is the secure, reliable way to use an RV-120W with a Mac?
View 1 Replies View RelatedI recently replaced a client's router with a Cisco RV 120W. The client employs a web-based application on an internal server that manages their business. Workers in the field use a handheld device power by WIndows Mobile to access a mobile version of the the web-based app. Data contained on the mobile app syncronizes with the server when workers choose a sync menu. Some workers perform this sync in the field, others wait till they return to the office and use the wireless provided by the router. Prior to changing the router, the synching worked fine either inside or outside the company network. The mobile app accesses the internal server via the router's public IP address. The router forwards the http requests to the internal server. But now the synching does not work internally. I assume it's because the Cisco RV 120 W does not support NAT Loopback, or I simply haven't figured out how to enable it. Does anyone know how to enable NAT Loopback on the RV 120 W so I can access the web-based app by through the router's external IP while on the private side of the LAN??
View 2 Replies View Relatedwe bought a router for our company RV042, so far good
What i did:
1. i created QuickVPN clients, droped in certificate which exported from router
******NOTE********All company's laptops are running: Windows 7pro 32bits****************
The users are connecting sucesefully to router and using resources from server etc...
But, when they press disconnect on quickVPN it shows disconnected, but when i log in into router, i still see that they are connected (not disconnecting),
and the problem is they cannot connect to router second time if i don't manually disconnect them from rv042 router....
Only sometimes the clients disconnect properly from router, but it is very very rare...
Question1: Where I should look for the problem in router rv042 or client laptops?
Question2: Does the 64bit windows7 pro OS can connect to RV042router?
I have latest quickvpn software and latest router firmware.
we recently bought a new desktop firewall solution from McAfee and I can't seem to get our VPN to work. I allowed QuickVPN in the firewall and additionally opened port 1194, 1720 and 1723 - but that does not do the trick. Once I turn off the firewall and use Windows Firewall instead it works.
View 2 Replies View RelatedI just can not find the way to check the mac address and computer name of the client which connected to my rv 120w?
View 1 Replies View RelatedHow can i check the website history in router?I want to know the website which the user explored through the router.
View 1 Replies View RelatedI just installed a new RV 120W to replace my dlink router.The problem is i cant display the configuration site (192.168.1.1). My internet is working fine and when i go to 192.168.1.1 i can logon (with the password i set using the installation disk) but then i see the top of the config site (blue) but where the config panel should be i see `site cannot be displayed`.
View 4 Replies View Relatedi am using the router,rv 120w can i redirect website to a special IP? for example,the website www.cisco.com, can i redirect it to the IP :8.8.8.8 in router?
View 1 Replies View RelatedI managed to set up an ipsec vpn between the RV 120W (responder) and Shrewsoft vpn client.The virtual ip and dns for the client pc are manually set. The tunnel is enabled, but I see no traffic between the local and the remote LAN.I can't ping or reach any pc behind the router.Using the command ipconfig /all on the client pc, I see that no gateway is assigned to the virtual vpn interface.So it seems that the RV 102W is unable to pass to the client the address of the default gateway for the lan, and I think this is why I can't access any resource.
View 4 Replies View RelatedI am not a tech guy but have to take care of some basic IT stuff. I had Ether fast cable/DSL router and it got changed with RV 120W router. there were comment that internet is now working slowly - what could be the reason for this?
I copied most of settings. First big technical problem was with phone. It stopped working - call could get through but when answered there was no sound. We use linksys modem for VoIP. I called operator and was told to disable sip alg. I did that and service improved a little. When answering a call sound could get through but would stop for few moments and then continue. Operator told me to forward port 16384 to 16482 to VoIP modem IP. But I can only set forwarding for one port at the time in "Port forwarding" settings. Is there a way to forward to port range?
I have a RV 120W router and SBS 2011 Essentials server. The remote access was working porperly, but now when I type the URL it brings up the RV login screen instead of the Remote Access sign in page. I am not certain what settings are messed up.
View 3 Replies View RelatedI have a RV120W; configured to perform port forwarding. I have Configured a Port Forwarding and Access Rule
* Sample Firewall: Access Rules:
Action | Service | Status | Connection Type | Source IP | Destination IP
[Code]....
Everything works, but in my destination server, i see as remote address the IP for the RV120W. I want it to forward also the originating IP address of the client (the remote address)
Is it possible to configure this?
I have also configured DMZ for my server, but see same behaviour
Firmware: 1.0.3.10
I have recently changed a couple of our companys office routers over from a netgear vpn router to this, all has gone well with the cisco router providing much better speed and reliablilty... But....
I have one little problem, at one of our offices they have a brother printer that has a scanner built in, since this change over the scanner does not seem to want to work,
as far as i can guess the router is blocking communication to the scanner, printing is working fine. is there anything that I need to enable or add to the settings on the cisco to get this working? I believe that the printer is using some kind of multicast to connect to the PC's
Very recently, we had implemented Site-to-Site VPN tunnel between two Linksys RV042 4-port VPN routers. Everybody in our remote site is accessing and sharing the data through this tunnel and it is working fine.
Now, we have a plan to implement the same for our mobile clients also. For this, we had followed all the basic configuration procedures and user got connected to Quick VPN tunnel. Here is a problem we had observed. The mobile client user is connected to the tunnel, but unable to access the office LAN from the PC.
Router is a version 1.1 running with sw version V1.1.13-ETSI
Quick VPN is sw version Ver 1.4.1.2
The issue is that I can't connect due to that i cant ping the internal IP, get this error message in the QVPN log [WARNING]Failed to ping remote VPN Router![URL]I have disable the "Block WAN Request" and it is possible to ping the router on the external site.So as I see it, the router blocks for ping on the internal IP via QVPN, what have I done wrong?
I have block some website in URL Blocking.But they can access the website which i have blocked through proxy server? Can i deny user access proxy server? It has many proxy server,i can not block the proxy server one by one.
View 1 Replies View RelatedWe have just acquired a Cisco RV120W Firewall Router and we are experiencing issues with this router. I've read some threads related to port forward issue with RV120W before writing this new topic.
We have 2 locations (site A and site B) connected with a Site to Site VPN (PPTP) running under Windows Server 2008 R2 with TMG 2010. This Site to Site VPN worked very well until we replaced our old router with the RV120W at site B. Since this moment, our engineers are not able to make the site to site VPN work again. The TMG box are located just behind the router.
We have followed some threads about Port Forwarding but it did not solve our issue (others port forwarding rules for RDP for example work). Our RV120W is running the last stable firmware (1.0.2.6) provided by Cisco.
I recently cut over from a WRT54G to a RV120W. I am having an issue where I type [URL] (for a server running on my network) in my web browser while on the internal network and it always comes back with the router login page. Basically it is supposed to go out of the router and then come back in on the public IP address and hit that server. There was a function on the WRT54G called "Filter Internet NAT redirection" which when turned off would allow this to happen. I am not seeing a feature like this on the RV120W
[URL]
can i share accouting software like Tally through quick vpn ? WRVS4400n has been configured on the site . and can connect to the site using quick vpn software without a problem . will Tally work ?
View 1 Replies View RelatedI recently installed a new RV120W router at one of my customer's office. I have 2 users connecting using the Quick VPN software.The first one is running on a Windows XP Pro SP3. Everything works great on this PC.The second PC is running on a Windows Vista - The QUICKVPN client stays at Veryfing Network and Eventually I get an error " The remote gateway is not responding. Do you want to wait?I have disabled Firewall on both PCS for troubleshooting purposes.
View 1 Replies View RelatedI have an RV042 using Quick VPN to connect to a remote network. I have port 1723 forwarded to a static IP address on a Windows 7 Pro 64 bit PC. I can establish the VPN and ping a printer but not the Win 7 PC. I can not acccess any shares on the pc via the IP address. It has Norton Antivirus and Windows Firewall. This remote PC replaced a Windows xp PC that allowed access to the shares. I have tried access with a Windows XP Pro and Windows Vista Home Premium PC. Neither have worked.
View 1 Replies View RelatedI want to connect two sites through a VPN tunnel, such that each machine can access all others, regardless of which site they're located.
The two sites have a VDSL connexion with dynamic public IP addresses. Unfortunately, our ISP does not offer static IP addresses with VDSL connexions.
I plan to do the following : install two RV 120W routers, one at each site, right after the VDSL modemconfigure the modems in bridge mode, such that the 120Ws get directly the WAN IP address and trafficuse DynDNS to assign domain names (site1.dyndns.org and site2.dyndns.org) to each siteassign different subnets to each site (ie 192.168.1/24 for site 1 and 192.168.2/24 for site 2)configure a VPN tunnel in gateway mode using the FQDN (site.dyndsn.org and site2.dyndns.org) of each site on both routers, with corresponding remote subnets
We have a customer running a RV 120W, and if the internet connection is disconnected it disables NAT, and you have to log on to the setup and enable it again. This is very annoying if the net connection goes down as you have to manually fix, why it does this and how to make it enable NAt by default?
View 4 Replies View RelatedI got RV 120W router and I need to setup VPN to connect remote clients (not site-to-site).
Is there any documents, examples or howtos described the way to setup it?
I need to setup a VPN into my home network ASAP.I have logmein so i can get in and setup a VM or something, but im not sure the best way to about this.I have TWC home
Internet---Modem---DlinkDIR-655 Router(no dhcp server)---Switch---network
I am running a 2008R2 DomainController/DNS/DHCP.I have hyper-v setup, so maybe a vm is easiest, just thought i would ask.Doesnt need to be super robust, this is a temporary solution.
I have a WRVS4400N router & am using Quick VPN to connect to the Router. I can able connect through Window XP Machine, but not able to connect through Window Vista & 7. Whenever I try to connect through Window 7, I got this message: The remote gateway is not responding. Right now the Cisco router is behind DSL modem and I can't change the DSL modem to bridge mode as my ISP told me that we can't change DSL modem to bridge mode. what I have to do to connect to the router through Windows 7 & Vista.
View 3 Replies View RelatedI have a hub / spoke configuration, with about 9 spokes. All connect ot the main office over a VPN, all native Cisco routers (2900 series)I want to use netflow to monitor traffic, and I started, but my results are not what I expected. I don't think I configured it properly.
Several interfaces have sub-interfaces, so if I'm reading correctly, I only export flow from the physical intyerface, not the sub-interfaces. Correct?I want both inbound and outbound traffic, so do I use the command twice with ingress and egress?What is the difference between V5 and V9?
Finally, how does NBAR fit in this? I want to see applications as well as just packets.
I have a laptop and a desktop pc both connected to the same wifi network, both running win 7. File transfers are not quick enough for my liking over wifi so when I need to move a few files about I tend to hook the two together with an ethernet cable. When I try to copy a file however it defaults to using the wireless connection. I'm getting around this at the moment by just turning the wifi off on the laptop while I do the transfers but it would be nice to not have to.
View 1 Replies View Related