Cisco Routers :: Stuck At Verifying Network QuickVPN Client RV 120W - Windows Vista
Sep 15, 2011
I recently installed a new RV120W router at one of my customer's office. I have 2 users connecting using the Quick VPN software.The first one is running on a Windows XP Pro SP3. Everything works great on this PC.The second PC is running on a Windows Vista - The QUICKVPN client stays at Veryfing Network and Eventually I get an error " The remote gateway is not responding. Do you want to wait?I have disabled Firewall on both PCS for troubleshooting purposes.
I used to have the problem where QuickVPN keeps on trying to verify the network because the RV042 cannot get the final ping to the client.I then bought a RV042 HW version 3 on the VPN side and I installed RV042's at the clients as well.This may look like overkill but believe me, it gives peace of mind, it made things a whole lot better, everybody happy.I am going to set up tunnels but for the time being the clients use QuickVPN. The above setup is all good if people access the vpn from the same source.
I now have a problem where one of our people is in Vietnam and she cannot access the vpn due to the "verifying network" loop.Looking at the log everything looks great, I compared a successful connect with an unsuccessful one and the logs are identical.The only difference is that the final ping is blocked (recorded in the QuickVPN log on the client side).The client uses W7 with firewall on.No need to repeat suggestions, such as turing printer sharing off, I have been through all that. isn't this simply caused by the ISP in Vietnam blocking pings ?
Is there a safe way to use the Cisco VPN Client (V5.x) and Cisco Quick VPN (V1.4.1.2) on the same Windows PC? I need to access my office RVS4000 and my customer's PIX 506 from the same laptop (but not at the same time).
Perhaps I should be asking "Is there a single Windows VPN client that works with both the Cisco RVS4000 and Cisco PIX 506? I have seen these questions asked on various forums but have yet to see a definitive answer.
I have a Cisco RV082 and can successfully connect with the Cisco QuickVPN Client, 1.4.2.1. However, after 1 to 5 minutes I see the Windows 7 bluescreen indicating that the system has halted due to a problem with a driver. I have installed the latest Windows updates and reinstalled the client.
The bluescreen only occurs if I use the Cisco QuickVPN Client.
I have a RV042 router setup with Client to gateway VPN access, and am connecting with a W7 PC running QuickVPN. We have many PC's that already have the standard CiscoVPN client on them, is it possible to configure the RV042 to allow these clients to conenct? I'm not sure how to get the Mutual authentication to work, or how to import the PEM certificiate into that client. It seems to allow it to import, but I can never select it.
The establishment of IPSEC tunnel between the RV220 and QuickVPN client works properly with the security certificate of origin of the router.RV220 V1.0.3.5QuickVPN V1.4.2.1
Since the establishment of a security certificate self-signed, the RV220 and QuickVPN client refuses to work together .
Here are the log of the QuickVPN client
2011/09/27 12:45:14 [STATUS]OS Version: Windows 7 2011/09/27 12:45:14 [STATUS]Windows Firewall Domain Profile Settings: ON 2011/09/27 12:45:14 [STATUS]Windows Firewall Private Profile Settings: ON 2011/09/27 12:45:14 [STATUS]Windows Firewall Private Profile Settings: ON
We have RV220W at corporate office...intent is to have (5) groups of (3) users each connecting via VPN. Had assumed would be using QuickVPN and have set up users, etc and connections at current locations are quick, smooth, reliable. I have set up (2) locations (6 users so far). However, after 4th connection (no matter where or in what order) client hangs at "Verifying Network" and doesn't complete connection. So, I have unique usernames, etc but each of the (3) at a location are hitting the router with the same IP. Is this the problem? I'm sure the RV220W can handle 15 simultaneous connections, but can the router deal with (3) connections from the same external IP?
I am setting up remote access using an RV042 router. Using quickvpn or a client-to gateway vpn and shrewsoft client, I can only access/ping the LAN side of the remote router and one machine on the remote network. The PPTP server and native Windows 7 connection provide access to all machines on the remote network.I have 2 possible reasons for this and would like to find the real reason:
1) The remote RV042 is behind another router, and that router restricts access other than the PPTP traffic.
2) The VPN tunnels other than PPTP only allow access to the remote LAN side of the router and remote machines that have the remote router defined as their gateway in the IP configuration.
I have a RVS4000 router, and using Quick VPN client (latest version, 1.4.2.1?) on a computer with Windows Vista. I can connect to the router, and I can see computers, and drives on the network. When I click on a drive or computer, I can't connect to the devices. Local IP address are 192.168.1.x, remote is 192.168.2.x.
I have been battling with my Cisco RV120W router and QuickVPN.Running Windows 7 Home PremiumPerformed a fresh install to factory out-of-box install for WindowsRemoved NortonDid NOT perform any windows updatesInstalled QuickVN version 1.2.4.1I have updated the firmware to the latest version (confirmed by cisco)I can connet to the router and have a stable connectionI can ping both the router IP and the shared file server IPWhen I enter the shared file server IP into the search field (e.g. \192.168.100.199) and press enter, I see a connection to "share", so I click on this and then see "FolderName" of my shared files. I click on this folder and I get a timed out error.When I enter the routers IP address into a browser (IE8 as factory installed) I get a timed out error also.In the past, I have installed all important and recommended updates for Windows and still get the same scenerioI have called cisco support and went through router settings, assigned them a VPN username, they log in and can access the files without issue (What the @#$$@#$)Cisco support spent plenty of time with me, but since they could access my network and since I could ping my devices, they had no other suggestions further.
I have this fresh factor out-of-box install. I know this is most likely something to do with my laptop that I am trying to use to connect to the network. I have Frontier as my ISP for home. I don't know if there is anything they are doing to interfere with my connection. I have tried to connect to the network via ComCast as well, with no luck.tell me if there is something I need to tweak in my Windows 7 settings?
I've been working on getting a client to Gateway configuration going for quite some time now. Had it working with a different Cisco single wan router that failed. The user replaced the router with an RV042 and we are trying to get the QuickVPN to once again connect to the router as it did before the replacement. Previously we did connect successfully with Windows 7 clients.
Router: RV042 v3 firmware 4.0.4.02-tm Quickvpn version 1.4.2.1
what i keep getting in the log is the following :
2012/10/02 12:55:07 [STATUS]OS Version: Windows Vista 2012/10/02 12:55:07 [STATUS]Windows Firewall Domain Profile Settings: ON 2012/10/02 12:55:07 [STATUS]Windows Firewall Private Profile Settings: ON
When I use QuickVPN under XP, I connect to my RVS4000 without problems. When I switch to new computer running Windows 7 and V4.2.1 QuickVPN I can get all the way to Verifying Network. Then I get the message that: "The remote gateway is not responding. Do you want to wait?" - repeatedly. The icon in the tool bar remains with a red slash and I am unable to ping devices on the lan side of the router. However, when I check the VPN Summary on the router, I see that it thinks I'm connected. When I check the VPN log I see that I am not:
Oct 12 10:27:53 - Configuration changed! Oct 12 10:28:33 - Configuration changed! Oct 12 10:28:34 - [VPN Log]: added connection description "ValR_rw_rw"
[Code]....
I've disabled MS Security Essentials and made sure the Firewall is on. IPSec Policy Agent and IKE and AuthIP IPSec Keying Modules services are both started. I've created a rule to allow QuickVPN throught the firwall in and out and a rule to let traffic on 443 and 60443 UDP and TCP through the Firewall.
I have recently changed a couple of our companys office routers over from a netgear vpn router to this, all has gone well with the cisco router providing much better speed and reliablilty... But....
I have one little problem, at one of our offices they have a brother printer that has a scanner built in, since this change over the scanner does not seem to want to work,
as far as i can guess the router is blocking communication to the scanner, printing is working fine. is there anything that I need to enable or add to the settings on the cisco to get this working? I believe that the printer is using some kind of multicast to connect to the PC's
Using the latest Cisco QuickVPN, my Windows 7, 64 bit laptop processes the QuickVPN connection to the point where the laptop attempts to ping the router and verify the connection. Those pings fail.Windows firewall is ON and IPSEC is started on the laptop. I have tried Kaspersky's firewall both enabled and disabled with no change.
I have a home network with an Actiontec Q1000 providing me 20 meg down and 5 meg up speeds. The DSL modem supports DHCP, DMZ, port forwarding, application forwarding, filtering, etc. I have an existing network 192.168.0.x that uses a combination of DHCP and static IP addresses for printers, scanners, and servers.I just purchased a RVS4000 and configured its LAN port to accept a DHCP address. It received the .26 address. I set up application and port forwarding so all VPN traffic goes to this address. I also put the router in the DMZ and turned off all firewalls.On the LAN side of the RVS4000 I use the 192.168.1.x address and have the 4000 provide DHCP addresses. I have a PC connected to the LAN port and it has the address of 1.100. I am able to use TeamViewer to connect to this through the internet and I can also access the devices on the Actiontec network from the PC connected to the 4000.I set up the VPN as best I could while going through appendix B of the admin guide. When I am at a remote location and use the QuickVPN client to access the 4000 I get the message, "The remote gateway is not responding. Do you want to wait?'. When I look at the log everything looks good except I get the following error:
[WARNING]Failed to ping remote VPN Router!
I am unable to get a DHCP address for my remote PC and am unable to ping any device on either network. What do I have configured wrong that this is not working?I only purchased this so I can use the VPN. Is the VPN established on the Actiontec LAN or on the RVS4000 LAN side? I am obviously connecting to the 4000 but am just not getting an address so I can not use my home office network for all my communications.
I installed QuickVPN v1.4.2.1 as it was in the download section on Linksys: [URL]
for the RV082 router we have. It connected but the program seemed buggy as there seemed to be no way to close the program after I used it so I wanted to uninstall it and install a more recent version of QuickVPN (side question: is it possible to VPN connect to my RV082 router with a different version of QuickVPN?).
I have Windows 7 Professional 64bit SP1 with all the latest updates. When I try to uninstall the program, at about the 25% mark of the window for 'QuickVPN Client Setup is preparing the InstallShield Wizard, which will guide you through the rest of the setup process. Please wait.' it seems to stop responding as holding the mouse over that windows just displayes a ring which goes round and round. I regret installing this buggy software on my PC.
My Dell was running very slow, so I used the disks that came with the computer to reinstall Windows XP. After doing this, it wasn't detecting our wireless network. I went through on the drivers disk and installed the drivers in order according to Dell's specifications. It still wouldn't work, so I went to the dell website from another computer, and downloaded the drivers that pertained to the network. Now it is recognizing the network, I was able to enter my key, but it won't stop "acquiring network address". When I do the ipconfig /all, it looks like there is no IP address:
Microsoft Windows XP [Version 5.1.2600] (C) Copyright 1985-2001 Microsoft Corp. C:Documents and SettingsUser>ipconfig /all
why QuickVPN clients can only reach RV042's LAN Network and not able to access subnet 1 remotely, however PPTP clients can access both..
Firmware Version : v4.1.1.01-sp (Dec 6 2011 20:03:18) Working Mode : Gateway Multiple Subnet: Enabled Device IP Address : 192.168.10.1 LAN: 192.168.10.1/255.255.255.0 Subnet 1: 172.16.10.1/255.255.255.0
QuickVPN clients able to reach all the resouces inside 192.168.10.1/24 remotely, but unable to access 172.16.10.1/24 network.Network 192.168.10.1/24 able to communicatie with network 172.16.10.1/24.PPTP clients able to access both subnets remotely.
My computer was recently cured of a damaged processor and a viral infestation, and it seems to be working properly again, however,I've been unable to connect to my network because the connection gets stuck on "acquiring network address".I am running Windows XP service pack 3 and the network device that isn't connecting is a Realtek RTL8168C(P)/8111C(P) PCI-E Gigabit Ethernet NIC.
I connect to the internet using a wireless USB. I woke up this morning and the internet showed that it was connected yet it wouldn't allow me to open the web or anything such as "msngr" I took the wireless card out for a couple minutes and then tried. That didnt do anything but say acquiring network address. I am not that knowledgeable when it comes to computers but these are the things that I have tried so far :
I went into properties and configure USB . . Made sure that the SSID said "Any" I Also tried going into properties and tcp/IP internet protocol and made sure it was on obtain IP address automatically . Hmm I tried. RUN>SERVICES> to make sure that the DHCP and TCP were started and on Automatic. I then tried system restore :- (went back about 2 weeks) . . Nothing. I then tried RUN>CMD>IPCONFIG/RELEASE *ENTER* IPCONFIG/RENEW *ENTER*.
when I did that it showed wireless network is now connected, yet back to ground zero. It wont let me browse. Its not really connected. When I look at the connection status, signal strenghth is good. Packets sent & received are good. I feel like there is just something little that. I am not getting, that is making this happen.
We have a newly-purchased RVS4000 v2 with firmware v2.0.2.7. Its intended role is as a gateway between our local network of wired workstations and a Cisco 2800 series Integrated Services Router, which is at the receiving end of our T1 line. It is configured with static IPs on both the LAN and the WAN side. It does NOT serve DHCP for the LAN. Ever since I installed it, I have had repeated complaints from users of Vista and Win7 workstations that they lose internet connectivity about every 20 - 30 minutes or so. The only solution is to unplug the workstation's CAT5 cable, count to 30, and plug it back in. Then everything's hunky dory for another 20 - 30 minutes. Meanwhile, all our Windows XP and Linux workstations enjoy uninterrupted internet access. The router/gateway we replaced (a DLink DIR-130) never had this problem.
My laptop is unable to connect to the internet. It recognizes my wireless connection (public network) as "unidentified network" and Access: "Local only." I've tried using many other solutions but I still haven't found a way to fix this. My other laptops, computers, and gaming devices are able to connect to my linksys router except for this laptop. [code]
I have Virgin Media services, I had a problem with my cable, which an engineer was booked for, but it magically fixed itself, so I cancelled the engineer. The engineer turned up for the appointment, which I was out for, then urged me over the phone to keep his number, and call me if I had any problems. I got home an hour later and my modem wouldn't sync. My guess is he did something with it outside so he would still get paid for the job. I called him up, and he came round and instantly replaced my old Virgin modem (which I was using with my own Belkin wireless router) with a new Virgin (Netgear) hub.I'm giving this bit of background to demonstrate, everything was fine before. [code] Since getting the new hub, I set up the wireless connections on the laptop and console, and internet is working fine. However none of the devices can share with eachother.When I go to network on either computer, neither computer sees either computer.All the sharing settings that I had before are unchanged, all that has changed is my modem/router combo has been replaced by a hub.
I have a Cisco SA520W router and needs to set up VPN. Du to major problems with the SSL VPN Client and windows 7, I had to let it go and try a different approach.
That was the QuickVPN client, but as it turs out, it simply impossible from reading the user manual to understand just how I have to set thing up. For instance, the VPN Wizard tells you to enter a preshared key. But in the QuickVPN Client, where do I enter the key?
And shall the "Enable Cisco VPN Client" be ticket off, I assumed yes, but seriously it is impossible to know.
Then in the VPN Wizard again, in the Remote & Local WAN Adress, what shall use FQDN or IP Address. The if FQDN, what shall a enter, the domain name for the router, whats the point in that? The domain name of the VPN Client, seriously, what's the point in that? I would assume that 99% of the VPN Client does NOT have a domain name. Then, if IP address, am I supposed to know the IP address of the client? Same with the "Secure Connection Remote Accessibility", what am I supposed to enter. The IP address which the Quick VPN Client network adapter shall have?
here is my setup:Old laptop with all my files is running Windows Vista.New laptop I got is running Windows 7.Both are connected on the same wireless network (same router and modem).I am looking for an easy way to copy and paste several folders and gigs worth of music, movies and photos to the new laptop with Windows 7. Is there a step-by-step guide on how to get these two laptops to recognize each other, and then access the files on Vista to copy and paste into Windows 7?
I have the RV 120W router, and can not seem to get SNMP Set to work. I though I would just check here, and make sure it is supported, and if it is, are there any special config settings I need to use?
I am interested in the QuickVPN solution for a Mac.I am getting mixed messages in my searches.If not, what is the secure, reliable way to use an RV-120W with a Mac?
The network is "connected" but the internet still does not work. I have wireless internet and a Windows Vista computer. It also says the network is unidentified.
