Cisco VPN :: SA520W Router - How To Setup QuickVPN Client
Mar 26, 2011
I have a Cisco SA520W router and needs to set up VPN. Du to major problems with the SSL VPN Client and windows 7, I had to let it go and try a different approach.
That was the QuickVPN client, but as it turs out, it simply impossible from reading the user manual to understand just how I have to set thing up. For instance, the VPN Wizard tells you to enter a preshared key. But in the QuickVPN Client, where do I enter the key?
And shall the "Enable Cisco VPN Client" be ticket off, I assumed yes, but seriously it is impossible to know.
Then in the VPN Wizard again, in the Remote & Local WAN Adress, what shall use FQDN or IP Address. The if FQDN, what shall a enter, the domain name for the router, whats the point in that? The domain name of the VPN Client, seriously, what's the point in that? I would assume that 99% of the VPN Client does NOT have a domain name. Then, if IP address, am I supposed to know the IP address of the client? Same with the "Secure Connection Remote Accessibility", what am I supposed to enter. The IP address which the Quick VPN Client network adapter shall have?
View 1 Replies
ADVERTISEMENT
Apr 27, 2008
How to setup quickvpn to work with RVS4000.
View 9 Replies
View Related
Feb 2, 2012
I connect to my RVS4000 VPN router using QuickVPN. Very useful.
Sometimes I am not near my laptop and need to check data.
Is there a QuickVPN or compatible client for a BlackBerry Torch 9850, even if it's only functional when connected to WiFi?
View 1 Replies
View Related
Jan 27, 2012
I am setting up remote access using an RV042 router. Using quickvpn or a client-to gateway vpn and shrewsoft client, I can only access/ping the LAN side of the remote router and one machine on the remote network. The PPTP server and native Windows 7 connection provide access to all machines on the remote network.I have 2 possible reasons for this and would like to find the real reason:
1) The remote RV042 is behind another router, and that router restricts access other than the PPTP traffic.
2) The VPN tunnels other than PPTP only allow access to the remote LAN side of the router and remote machines that have the remote router defined as their gateway in the IP configuration.
View 2 Replies
View Related
Jan 14, 2012
I bought a router Cisco WRVS4400N Wireless-N Gigabit Security Router - VPN v2.0 with the intention of using with the Quick VPN Client for connecting to my home network.
My home network is connected to a pre provide by my ISP Thomson TG784 and is connected to it but all my main network is controlled by the WRVS4400N, I have forward all the doors, as you can see by the log part below, and by analyzing the log you can see that I can't get any PING to complete the VPN connection.
OS is windows 7
QuickVPN Clien is 1.4.2.1
WRVS4400N firmware is v2.0.2.1
Thomson TG784 firmware is 8.4.2.Q
Log from Quick VPN
2012/01/11 19:44:03 [STATUS]One network interface detected with IP address 192.165.0.196
2012/01/11 19:44:03 [STATUS]Connecting...
2012/01/11 19:44:03 [DEBUG]Input VPN Server Address = husportugal.dnsalias.com
[code]....
Log from WRVS4400N
Jan 15 10:12:53 - [VPN Log]: added connection description "Casa_rw_rw"
Jan 15 10:12:54 - [VPN Log]: listening for IKE messages
Jan 15 10:12:54 - [VPN Log]: forgetting secrets
[code]....
View 0 Replies
View Related
Dec 14, 2009
I have a problem to configure a IPSEC VPN on the SA520W ( 1.0.39) with Cisco VPN Client (5.0.05.290). In the logs are following error:
ERROR: Could not find configuration for x.x.x.xERROR: Could not find configuration for x.x.x.xERROR: Could not find configuration for x.x.x.xERROR: Could not find configuration for x.x.x.x
View 9 Replies
View Related
Dec 19, 2012
How to setup the quickvpn.... I am getting the message Servers certificate doesnt exist on your local computer..... and the the window fail to establish the connection
View 1 Replies
View Related
Nov 8, 2011
Is there a way to set up Quick VPN on the RV120W without changing the internal subnet? I have just taken over responsibility for a network and I don't know all of the nooks and crannies yet, so I'd rather not change the internal sub net. I've tried setting up a user then changing the LAN settings afterward, but it automatically removed the VPN user when I did so.
View 1 Replies
View Related
Mar 16, 2011
Setting up vpn using quickvpn client to asa5505. QucikVPN client version is 1.4.1.2. I need to use port 60443, port 443 is already taken.
View 1 Replies
View Related
Sep 21, 2011
Is there a safe way to use the Cisco VPN Client (V5.x) and Cisco Quick VPN (V1.4.1.2) on the same Windows PC? I need to access my office RVS4000 and my customer's PIX 506 from the same laptop (but not at the same time).
Perhaps I should be asking "Is there a single Windows VPN client that works with both the Cisco RVS4000 and Cisco PIX 506? I have seen these questions asked on various forums but have yet to see a definitive answer.
View 2 Replies
View Related
Nov 15, 2011
I have a RV042 router setup with Client to gateway VPN access, and am connecting with a W7 PC running QuickVPN. We have many PC's that already have the standard CiscoVPN client on them, is it possible to configure the RV042 to allow these clients to conenct? I'm not sure how to get the Mutual authentication to work, or how to import the PEM certificiate into that client. It seems to allow it to import, but I can never select it.
View 2 Replies
View Related
Nov 21, 2012
I have a Cisco RV082 and can successfully connect with the Cisco QuickVPN Client, 1.4.2.1. However, after 1 to 5 minutes I see the Windows 7 bluescreen indicating that the system has halted due to a problem with a driver. I have installed the latest Windows updates and reinstalled the client.
The bluescreen only occurs if I use the Cisco QuickVPN Client.
View 4 Replies
View Related
Nov 21, 2011
The establishment of IPSEC tunnel between the RV220 and QuickVPN client works properly with the security certificate of origin of the router.RV220 V1.0.3.5QuickVPN V1.4.2.1
Since the establishment of a security certificate self-signed, the RV220 and QuickVPN client refuses to work together .
Here are the log of the QuickVPN client
2011/09/27 12:45:14 [STATUS]OS Version: Windows 7
2011/09/27 12:45:14 [STATUS]Windows Firewall Domain Profile Settings: ON
2011/09/27 12:45:14 [STATUS]Windows Firewall Private Profile Settings: ON
2011/09/27 12:45:14 [STATUS]Windows Firewall Private Profile Settings: ON
[code].....
View 4 Replies
View Related
Sep 27, 2011
I am trying to setup VPN with WRVS4400N and Quick VPN on client side. I am fairly new to VPN and did some research and looked through the manual but can't seem to get it to work so far and from what I noticed many people are having this problem.
Basically it gives the "Failed to establish connection" generic error, shows it almost instantly.It also showed the certificate error before but then I read about putting it in the installation directory and it stopped showing it, and whats strange is later I removed it but it doesnt show the error any longer, so don't know if its caching it somewhere or what can be going on...
In effort to look for answer and test things out I tried to connect to another location and setup a WRV200 router, I also get the same error but not instantly, it even shows "Activating Policy" but then doesn't go farther and shows the generic error.Also with this setup strangly it always shows the certificate error, no matter if I put one in directory or not... Even tried to name it as the WRVS4400N certificate name...
Anyway VPN IPSec is disabled, and Client Accounts are configured and changed password several times to make sure its correct, VPN Passthrough enabled on all 3 options. I tried to disable Windows Router, I also have a router in place do I possibly need to open some type of ports for the QuickVPN client?
View 1 Replies
View Related
Sep 1, 2011
I have a RVS4000 router, and using Quick VPN client (latest version, 1.4.2.1?) on a computer with Windows Vista. I can connect to the router, and I can see computers, and drives on the network. When I click on a drive or computer, I can't connect to the devices. Local IP address are 192.168.1.x, remote is 192.168.2.x.
View 9 Replies
View Related
Aug 22, 2011
The PPTP client from Windows 7 is not working with this router; therefore I would like to try the quickvpn.Is there any paper from Cisco explaining how to setup the RV120W for quickvpn ?
View 1 Replies
View Related
Sep 15, 2011
I recently installed a new RV120W router at one of my customer's office. I have 2 users connecting using the Quick VPN software.The first one is running on a Windows XP Pro SP3. Everything works great on this PC.The second PC is running on a Windows Vista - The QUICKVPN client stays at Veryfing Network and Eventually I get an error " The remote gateway is not responding. Do you want to wait?I have disabled Firewall on both PCS for troubleshooting purposes.
View 1 Replies
View Related
Aug 10, 2010
I did upgrade to WiSM from v5.1 to V6 then i see this log %WCP-3-KEEPALIVE_LOST: wcp_controller_server.c:1763 Lost keepalives from Cat 6K Supervisor.
View 6 Replies
View Related
Sep 13, 2011
I have a home network with an Actiontec Q1000 providing me 20 meg down and 5 meg up speeds. The DSL modem supports DHCP, DMZ, port forwarding, application forwarding, filtering, etc. I have an existing network 192.168.0.x that uses a combination of DHCP and static IP addresses for printers, scanners, and servers.I just purchased a RVS4000 and configured its LAN port to accept a DHCP address. It received the .26 address. I set up application and port forwarding so all VPN traffic goes to this address. I also put the router in the DMZ and turned off all firewalls.On the LAN side of the RVS4000 I use the 192.168.1.x address and have the 4000 provide DHCP addresses. I have a PC connected to the LAN port and it has the address of 1.100. I am able to use TeamViewer to connect to this through the internet and I can also access the devices on the Actiontec network from the PC connected to the 4000.I set up the VPN as best I could while going through appendix B of the admin guide. When I am at a remote location and use the QuickVPN client to access the 4000 I get the message, "The remote gateway is not responding. Do you want to wait?'. When I look at the log everything looks good except I get the following error:
[WARNING]Failed to ping remote VPN Router!
I am unable to get a DHCP address for my remote PC and am unable to ping any device on either network. What do I have configured wrong that this is not working?I only purchased this so I can use the VPN. Is the VPN established on the Actiontec LAN or on the RVS4000 LAN side? I am obviously connecting to the 4000 but am just not getting an address so I can not use my home office network for all my communications.
View 1 Replies
View Related
Nov 23, 2012
Trying to setup client VPN access on a 1841 router. essentially i would like to connect using the cisco vpn application.
View 2 Replies
View Related
Jan 25, 2013
I have a sa520w router I configured w a vlan for the wireless and port 2. Now I would like the switch to handle both traffic from the default lan and the vlan. I tried creating a vlan on ports 28 and 10 but I cant get it to work. I have my other lan on port 27. Ive read something about switch layers? not sure. so I want port 10 to route to the vlan and other ports go to the default lan.
View 19 Replies
View Related
Apr 18, 2010
I'm trying to connect through a VPN to RVS4000 router that I have VLAN'ed into two seperate networks 192.168.1.x (default) and 192.168.77.x. When i connect with the QuickVPN Client, I have no problems seeing devices on the 192.168.1.x network but i can't see the 192.168.77.x devices; so i'm assuming that the QuickVPN client software puts me on the default network and not the "77" network. Thing is, i only want to VPN into the "77" network and not the 192.168.1.x network.
Will QuickVPN allow me to do this? If not how do I VPN into the 192.168.77.x network?
View 4 Replies
View Related
Mar 15, 2011
We currently have a company network set up with a PC acting as a shared resource containing shared folders for everyone to access (approx 30 users)The network is comprised of a business internet connection to a 5 port router which is then connected to a 5 port switch connecting to 4 computers and another switch which is connected to another 4 computers and again to another switch - this continues for approx 30 - 35 computers.We have 2 shipping databases connected to the first switch (2 of the for first computers mentioned) and about 15 of the 30 clients need to access these. Because there is this many people on the network we are running really slow and losing access to the databases/shared files on the network.We do not have the expertise or time/money to set up a true server/client network.We are moving to a bigger building and potentially hiring 10-20 more people.We are thinking about having a small (5port router) and branching it off to 2 24 port gigabit switches and the business folder and having one switch contain the 2 databases and all the users who need to access it and the other switch containing all the other users.
View 18 Replies
View Related
Apr 12, 2011
I want to set up our ASA5505 firewall to allow access from the Cisco VPN Client software.I have nstalled the client software then tried using the VPN wizard to set up the connection without success, I am running Windows 7 32 bit and Cisco client 5.0.03.0530. [code]
View 22 Replies
View Related
Sep 18, 2011
I have just purchased and setup a vpn on my ASA5505 and now I wish to setup a Windows VPN client to use it. Does CISCO have any free vpn clients for Windows?I tried to download a client from the CISCO downloads area, but it's for some kind of purchase agreement. I would have thought that the vpn client was free to download given my ASA comes with two free vpn licenses.
View 5 Replies
View Related
Mar 27, 2011
I've the following scenario VPN Concentrator is connected to a router which is connected to a router and at the edge Cisco 515E PIX is connected to the internet. The problem is that the normal VPN Dial-up connection (a utility of windows) are getting connected but Cisco VPN Client throws error 412. Here's what I've tried (Initially groups and user were created):
(1) Allowed port 10000 on PIX ( access-list from-outside-coming-in permit tcp any host <public ip> eq 10000) and checked IPSec over UDP on VPN Conc. under Mode Config tab. Also checked IPSec over TCP tab under tunneling panel at port 10000. Tried connecting through VPN Client but it threw error 412
(2) In the reference guide, I read that IPSec over NAT is allowed on ports ranging from 4000 something to 40000 something.
I tried 33333, both on PIX and VPN Conc. under Mode Config tab but still no use. Same error 412.
View 3 Replies
View Related
May 15, 2013
I want to ask if is possible to configure the RV180 behind my DSL Router to connect using QuickVPN. First I tried to connect to the PPTP server and worked fine, but when I tried to connect using QickVPN, seems to connect but when the client says "verifying network" after a while appears the message "network not responding..."
In my DSL-Router forwared this ports: UDP: 500,4500,443,60443 - TCP: 443,60443 (i don't know if tcp ports are needed but I opened for testing) and allowed protocol ESP (comes with the rule to allow IPSEC-L2TP)
View 3 Replies
View Related
Sep 15, 2011
I want to setup NAT with ASDM on ASA for a client and I can not make it work. I have several interface:
Inside: 10.97.0.1 / 24
Outside: 10.0.1.70 /24
Interco: 192.168.6.1 /24
Other Sites: 10.26.0.4 /24
All routing in the network is Ok My customer want to access a server @ ip 10.194.70.1 in https on the interface Interco with his nat address as 10.97.0.11 .This server must be accessible with the address 10.97.0.11:443 from interfaces inside, outside and other sites.And source address must be nated with original destination address 10.97.0.11 to be redirected on 10.194.70.1.
View 7 Replies
View Related
Dec 1, 2012
I've just installed a standard Cisco wireless install (5508, 3502i, local and flexconnect setups) all working swimmingly.
The customer has asked for a new WLAN for a particular group of staff that will route to a different gateway than the general wireless staff.
The 5508 is connected to a older Avaya L3 switch that is the customers core swtich, but it isn't capable of PBR so it routes on desitnation only and its default route is not where I need the new WLAN traffic to route to. An ASA will be connected to the Avaya switch (which is the alternate gateway I need to get the new WLAN users to). So my question is probably routing 101, but if the ASA interface, the Avaya swtich and the WLAN interface all reside in the same VLAN, can I give the wireless clients the ASA as their gateway via DHCP and successfully get their traffic to the ASA?
View 3 Replies
View Related
Jan 6, 2010
I just bought this router (4400N) at a retail store for $239.00 with a ship date of 12/2009 and the QuickVpn client will NOT work with Windows 7. Furthermore, I do not see any
signs of Cisco fixing this.I would be happy if I could use the pptp and the MS Clients. There is no pptp option in the 4400N. All I can do is port forward to my MS server. This does work, but then I cant vpn out....Unfortunately, I will have to return this router for a "STORE CREDIT" . This product should be removed from the shelves and recalled until the client works with Vista and Windows 7 in any way or fashion.Yes, I did install the 1.3 version and I even tried it in compatibility mode for XP?
View 14 Replies
View Related
Sep 24, 2006
my office network is running using a Linksys Router RV042 and at home i have a Linksys Router BEFVP41. i'm trying to setup a QuickVPN from home to my office but having problems. both routers have different LAN IPs. the firmware version for my two routers are listed belowRV042 - ver. 1.3.7.4BEFVP41 - ver. 1.02.00?
View 5 Replies
View Related
Dec 3, 2012
I setup RV042s at a clients offices for the VPN support and am now finding that multiple sip clients behind the router does not work. I found a thread on tech and it looks like there's a case open for the issue. url... How to get this working other than assigning IPs for the phones and dealing with different ports.
View 1 Replies
View Related
Nov 6, 2011
I'm trying to set up a 5505 (running 8.3) so that i can use the client vpn through RADIUS authentication.I have set up a new local RAIDUS windows box and used the ASDM asistant and a few other guides to setup the 5505.
View 3 Replies
View Related
