Cisco VPN :: WRVS4400N Trying To Setup VPN With QuickVPN
Sep 27, 2011
I am trying to setup VPN with WRVS4400N and Quick VPN on client side. I am fairly new to VPN and did some research and looked through the manual but can't seem to get it to work so far and from what I noticed many people are having this problem.
Basically it gives the "Failed to establish connection" generic error, shows it almost instantly.It also showed the certificate error before but then I read about putting it in the installation directory and it stopped showing it, and whats strange is later I removed it but it doesnt show the error any longer, so don't know if its caching it somewhere or what can be going on...
In effort to look for answer and test things out I tried to connect to another location and setup a WRV200 router, I also get the same error but not instantly, it even shows "Activating Policy" but then doesn't go farther and shows the generic error.Also with this setup strangly it always shows the certificate error, no matter if I put one in directory or not... Even tried to name it as the WRVS4400N certificate name...
Anyway VPN IPSec is disabled, and Client Accounts are configured and changed password several times to make sure its correct, VPN Passthrough enabled on all 3 options. I tried to disable Windows Router, I also have a router in place do I possibly need to open some type of ports for the QuickVPN client?
View 1 Replies
ADVERTISEMENT
Oct 22, 2011
Hardware: WRVS4400N on Firmware version: V2.0.2.1-ETSI
Quick VPN Version 1.4.2.1 on Windows7 Ultimate 64bit.
QuickVPN Client stopps with: Verifying Network.... and "The remote gateway is not responding. Do you want to wait? Yes / No"
Here we go with the log:
2011/10/24 09:09:06 [STATUS]OS Version: Windows 7
2011/10/24 09:09:06 [STATUS]Windows Firewall Domain Profile Settings: OFF
2011/10/24 09:09:06 [STATUS]Windows Firewall Private Profile Settings: OFF
2011/10/24 09:09:06 [STATUS]Windows Firewall Private Profile Settings: OFF
2011/10/24 09:09:07 [STATUS]One network interface detected with IP address 192.168.11.106
[code]....
Additional I can ping to dirkle.dyndns.org as well as accessing to the WRVS4400N [URL] The connection map is as following:
Client --> PPPoE DSL Router --> (...INTERNET...) --> NetvigatorGateway ---> WRVS4400N --> HomeNetwork
The NetvigatorGateway is locatet at my home and also distributing IP-TV. For internet it netvigator gateway is set DMZ to WRVS4400N (network 192.168.1.xxx); the WAN IP is assigned to the WRVS4400N and same as on dirkle.dyndns.org. When I connect myself into the netvigator gateway, (network 192.168.8.xxx) i can successfully establish a VPN connection with QuickVPN to the WRVS4400N.But then, what reason ever, I cannot access to 192.168.1.xxx network devices. QuickVPN does not allow me to see the assigned IP as well. This is my issue 2: After the connection is "successfully" established, it does not feel as I am part of the home network....Issue 3 would be: In the company we use CiscoAnyConnect VPN client (Verison 2.4.0202). Is it possible in using this client instead in any later firmware revision?
View 0 Replies
View Related
Dec 11, 2011
I've deployed a WRVS4400N router at one of my clients, however I'm unable to access resources on his network via DNS. I was hoping to use the router for DNS resolution, however when I connect via VPN, I can only connect to shares via IP address.
View 1 Replies
View Related
Oct 23, 2009
I have a new WRVS4400N VPN router and have set it up for VPN. On a separate computer I have a Verizon EVDO card so I have used that with a separate computer to access the internet on a public, routable IP address off of my network.
When I use the QuickVPN client, I wasn't able to get into my network (using ddyns.org) because I didn't have the "BLOCK WAN REQUEST" setting disabled so the router could be ping'd. Once I did that, I verified I could successfuly ping my ddyns name abc.xyz.com.
In the error log of the QuickVPN client, I still see:
2009/10/24 16:57:15 [STATUS]OS Version: Windows XP2009/10/24 16:57:16 [STATUS]Windows Firewall is OFF2009/10/24 16:57:16 [STATUS]One network interface detected with IP address x.x.x.x2009/10/24 16:57:16 [STATUS]Connecting...2009/10/24 16:57:16 [STATUS]Connecting to remote gateway with IP address:x.x.x2009/10/24 16:57:28 [WARNING]Remote gateway wasn't reached...2009/10/24 16:57:36 [STATUS]Remote gateway was reached by https ...2009/10/24 16:57:36 [STATUS]Provisioning...2009/10/24 16:57:47 [STATUS]Tunnel is configured. Ping test is about to start.2009/10/24 16:57:47 [STATUS]Verifying Network...2009/10/24 16:57:51 [WARNING]Failed to ping the LAN IP of the remote VPN Router!2009/10/24 16:57:52 [WARNING]Failed to
[code]....
I HAVE been able to make the connection successfully without any other changes to the environment. It's hit or miss, but usually a miss. Restarting QuickVPN sometimes works on the next try, but then fails if I disconnect and try again. Even when that ping error message is appearing, I am able to ping the host name at a command prompt without a problem.
Is something else on the router possibly blocking the ping requests?My router is behind a Westell F90 6100 DSL modem operating in bridge mode. The 4400 is obtaining the WAN address from Verizon(DSL) and that is also where I have my PPOE info entered to obtain the internet connection.
View 7 Replies
View Related
Jan 14, 2012
I bought a router Cisco WRVS4400N Wireless-N Gigabit Security Router - VPN v2.0 with the intention of using with the Quick VPN Client for connecting to my home network.
My home network is connected to a pre provide by my ISP Thomson TG784 and is connected to it but all my main network is controlled by the WRVS4400N, I have forward all the doors, as you can see by the log part below, and by analyzing the log you can see that I can't get any PING to complete the VPN connection.
OS is windows 7
QuickVPN Clien is 1.4.2.1
WRVS4400N firmware is v2.0.2.1
Thomson TG784 firmware is 8.4.2.Q
Log from Quick VPN
2012/01/11 19:44:03 [STATUS]One network interface detected with IP address 192.165.0.196
2012/01/11 19:44:03 [STATUS]Connecting...
2012/01/11 19:44:03 [DEBUG]Input VPN Server Address = husportugal.dnsalias.com
[code]....
Log from WRVS4400N
Jan 15 10:12:53 - [VPN Log]: added connection description "Casa_rw_rw"
Jan 15 10:12:54 - [VPN Log]: listening for IKE messages
Jan 15 10:12:54 - [VPN Log]: forgetting secrets
[code]....
View 0 Replies
View Related
Nov 8, 2011
Is there a way to set up Quick VPN on the RV120W without changing the internal subnet? I have just taken over responsibility for a network and I don't know all of the nooks and crannies yet, so I'd rather not change the internal sub net. I've tried setting up a user then changing the LAN settings afterward, but it automatically removed the VPN user when I did so.
View 1 Replies
View Related
Aug 22, 2011
The PPTP client from Windows 7 is not working with this router; therefore I would like to try the quickvpn.Is there any paper from Cisco explaining how to setup the RV120W for quickvpn ?
View 1 Replies
View Related
Aug 10, 2010
I did upgrade to WiSM from v5.1 to V6 then i see this log %WCP-3-KEEPALIVE_LOST: wcp_controller_server.c:1763 Lost keepalives from Cat 6K Supervisor.
View 6 Replies
View Related
Mar 26, 2011
I have a Cisco SA520W router and needs to set up VPN. Du to major problems with the SSL VPN Client and windows 7, I had to let it go and try a different approach.
That was the QuickVPN client, but as it turs out, it simply impossible from reading the user manual to understand just how I have to set thing up. For instance, the VPN Wizard tells you to enter a preshared key. But in the QuickVPN Client, where do I enter the key?
And shall the "Enable Cisco VPN Client" be ticket off, I assumed yes, but seriously it is impossible to know.
Then in the VPN Wizard again, in the Remote & Local WAN Adress, what shall use FQDN or IP Address. The if FQDN, what shall a enter, the domain name for the router, whats the point in that? The domain name of the VPN Client, seriously, what's the point in that? I would assume that 99% of the VPN Client does NOT have a domain name. Then, if IP address, am I supposed to know the IP address of the client? Same with the "Secure Connection Remote Accessibility", what am I supposed to enter. The IP address which the Quick VPN Client network adapter shall have?
View 1 Replies
View Related
Sep 13, 2011
I have a home network with an Actiontec Q1000 providing me 20 meg down and 5 meg up speeds. The DSL modem supports DHCP, DMZ, port forwarding, application forwarding, filtering, etc. I have an existing network 192.168.0.x that uses a combination of DHCP and static IP addresses for printers, scanners, and servers.I just purchased a RVS4000 and configured its LAN port to accept a DHCP address. It received the .26 address. I set up application and port forwarding so all VPN traffic goes to this address. I also put the router in the DMZ and turned off all firewalls.On the LAN side of the RVS4000 I use the 192.168.1.x address and have the 4000 provide DHCP addresses. I have a PC connected to the LAN port and it has the address of 1.100. I am able to use TeamViewer to connect to this through the internet and I can also access the devices on the Actiontec network from the PC connected to the 4000.I set up the VPN as best I could while going through appendix B of the admin guide. When I am at a remote location and use the QuickVPN client to access the 4000 I get the message, "The remote gateway is not responding. Do you want to wait?'. When I look at the log everything looks good except I get the following error:
[WARNING]Failed to ping remote VPN Router!
I am unable to get a DHCP address for my remote PC and am unable to ping any device on either network. What do I have configured wrong that this is not working?I only purchased this so I can use the VPN. Is the VPN established on the Actiontec LAN or on the RVS4000 LAN side? I am obviously connecting to the 4000 but am just not getting an address so I can not use my home office network for all my communications.
View 1 Replies
View Related
Dec 19, 2012
How to setup the quickvpn.... I am getting the message Servers certificate doesnt exist on your local computer..... and the the window fail to establish the connection
View 1 Replies
View Related
Apr 6, 2013
How to setup VPN connection,
Head office : fortigate 200b firewall - SSL, IPsec
Branch office: WRVS4400N Wireless-N Gigabit Security Router with VPN
Both side have the public IP.
View 1 Replies
View Related
Oct 23, 2011
i bought this router because I wanted a gigabit router for my small business and I figured whats better than a small business router? Well, one think I used pretty heavily on my Linksys WRG54GS was a simple port forward to my XP box for VPN. I know nothing about how to currectly set up VPN in this router. Does this router have a built in VPN server? Also, is there anyway to completely disable everything VPN side on this router and simply forward my port 1723 to my computer again? I am using this in conjunction with my android phone. I downloaded the AnnyConnect software, but yielded zero success. I have a working tun.ko installed on my rooted android phone, but this all is completely too much work for something that worked very well before using simple port forwarding and the built in vpn client on the phone. How can I correctly set up my router for the VPN to use with the AnnyConnect application I have on my cell phone?
View 1 Replies
View Related
Aug 29, 2011
I have a WRVS4400N setup as a main router for one of our bays. For wired connections it is working with no problems. When I first installed it it ran fine for wireless as well. I was trying to get WDS to work and at some point the wireless stopped working. My laptop can no longer connect to it and often cannot see it when doing a scan for networks. I have already checked that it isn't a problem with the laptop, that there are not other networks causing interferance, and even tried resetting to default configs.
View 1 Replies
View Related
Jan 25, 2011
A query here with regards to Wireless isolation between SSID and wireless isolation within SSID.If we have 2 SSID, eg. InternalSSID, GuestSSID on AP1.Both SSID are set to Enabled for isolation between SSID, and within SSID, that would mean all machines connected thro' this AP1, would be isolated from one another.
1) If there's 1 laptop that connects to another AP, lets call it AP2, (doesn't have isolation function) on ssid01. Would this laptop still be isolated from those that connects to the first AP?
2) If there are wired PCs connected to the router. And the 2 APs are connected to the same router. Would the machines connected thro' the AP1 on either InternalSSID, GuestSSID be able to access those wired PCs? (My assumption is yes.)
3) Is there a quick and efficient way to setup on WRVS4400N to isolate GuestSSID totally from InternalSSID, and wired PCs. InternalSSID and wired PCs should be allowed to 'see' one another.
The challenge here is that, the network points are all installed already. Both AP are connecting thro' 2 separate unmanaged switch together with a couple of other PCs. 1 Port on the unmanaged switch, each,connects to the router.
View 1 Replies
View Related
Jul 10, 2011
I work at a small private school that is going to implement about 20 ipads for classes. Students bring their ipods and iphones and are connecting to the existing unsecured wireless access points and are taking up the remaining IP addresses in the DHCP scope. I am running out of IP addresses and was wondering if I could set up a VLAN using the Cisco WRVS4400N for all of these wireless devices the students will be using. I plan to pull out all unsecured wireless AP's and replace with what ever solution we come up with. I will need about 6 access points/routers to cover the entire school. There is not a lot of money for technology and the ipods were donated. I have never set up a VLAN before. Is there an inexpensive way to allow the students with their personal ipads/ipods and the 20 ipads owned by the school to connect to a VLAN to keep from using up our DHCP IP addresses from the server.
View 1 Replies
View Related
Jan 29, 2012
Just bought 3 WRVS4400N, I wanted to setup gateway to gateway VPN. I followed the instructions on the WRVS4400N admin guide and VPN does not connect. I also downloaded the VPN setup wizard and that also did get the gateway connected. Everything seems to be correct. Do I have to enable anything else? Firewall setting?
Below is my config.
IPSec VPN Tunnel: Enabled
Tunnel Name: TUN01
Local Security gateway: IP only
WAN1 IP: 192.168.100.1
SUBNET: 255.255.255.0
Local Security type: subnet
LOCAL IP: 10.10.10.1
SUBNET: 255.255.255.0
[code]....
View 1 Replies
View Related
Jul 13, 2011
I have configured the RV220W based on the user guide (which doesn't say much), created IPsec User and installed QuickVPN 1.4.1.2 on a remote computer. I launched the application filled out the login info and it connects but what's next?I can not ping any IP from the LAN attached to the remote router nor map any shared devices.I was hoping after a succesful connection to see my local IP address change to the one from the LAN I am remotely connected to...
View 4 Replies
View Related
Apr 2, 2012
what exactly is QuickVPN?Is it a IPSec VPN?Is it a PPTP?Is it a SSLVPN?can I resolve my local hostnames? That means, can I configure a lokal DNS Server?
View 3 Replies
View Related
Oct 28, 2011
I'm running Cisco QuickVPN on a clients laptop (Windows 7). Windows firewall is disabled because McAfee SaaS is running.I sometimes have the issue that the initial connection attempt comes back with "Gateway not respoding" during the network verification process. You close the program, you open it again and it works. Sometimes it takes 2 or 3 tries. Today I have the issue that my client tried it like 20 times including several reboots and it's just not working. I tried it from my own computer and it connected fine on the 2nd try.I'm thinking that it might be time-out thing, that the VPN client doesn't receive a response fast enough? I know my clients home internet is darn slow.
View 1 Replies
View Related
Oct 21, 2011
So have a RV042 VPN router that is directly connected to the ethernet port of our comcast cable modem.
If I connect to it using QuickVPN (1.4.2.1) from a PC that is connected using AT&T 3G Network it works fine!
If I connect to it using QuickVPN (1.4.2.1) from a different PC that is connected using home WiFi (linksys wrtxxx) then it fails. In the VPN log all I see is failure messages for ping.
2011/10/22 15:47:28 [WARNING]Failed to ping remote VPN Router!
If I open a regular command prompt and attempt to ping the VPN router it works so not understanding why the QuickVPN is unable to ping.
how I can troubleshoot this further. Makes me think the RV042 config is fine otherwise it would not work on a 3G connection. Something on the home PC or the home network. Not sure what to check.
View 2 Replies
View Related
Mar 11, 2012
I've one RV042. I've configured VPN PPTP and it work (I've redirect port 1723 on router1 to rv042). If I can try to use quickVpn, client login and receive error "remote gateway is not responding". I have redirect port 60443 from router1 to rv042. Connection it's this: INTERNET-router1-RV042.
View 3 Replies
View Related
Oct 29, 2011
I have been battling with my Cisco RV120W router and QuickVPN.Running Windows 7 Home PremiumPerformed a fresh install to factory out-of-box install for WindowsRemoved NortonDid NOT perform any windows updatesInstalled QuickVN version 1.2.4.1I have updated the firmware to the latest version (confirmed by cisco)I can connet to the router and have a stable connectionI can ping both the router IP and the shared file server IPWhen I enter the shared file server IP into the search field (e.g. \192.168.100.199) and press enter, I see a connection to "share", so I click on this and then see "FolderName" of my shared files. I click on this folder and I get a timed out error.When I enter the routers IP address into a browser (IE8 as factory installed) I get a timed out error also.In the past, I have installed all important and recommended updates for Windows and still get the same scenerioI have called cisco support and went through router settings, assigned them a VPN username, they log in and can access the files without issue (What the @#$$@#$)Cisco support spent plenty of time with me, but since they could access my network and since I could ping my devices, they had no other suggestions further.
I have this fresh factor out-of-box install. I know this is most likely something to do with my laptop that I am trying to use to connect to the network. I have Frontier as my ISP for home. I don't know if there is anything they are doing to interfere with my connection. I have tried to connect to the network via ComCast as well, with no luck.tell me if there is something I need to tweak in my Windows 7 settings?
View 11 Replies
View Related
Mar 6, 2012
I have a Cisco RV120W connected to the internet. I have configured a QuickVPN user on the router, but I cannot connect via QuickVPN no matter on what PC I try (with firewall or without firewal, Windows XP, 7, ...). On the router it says the VPN user is connected, but on the client PC I receive remote gateway not responding. In the logs it says failed to ping remote VPN router. I tried changing all settings I could find on this forum, but the result stays the same (changed port to 60443, deleted all IKE and VPN policies, allowed ping, disabled fragmented packets etc...). None of all the settings seems to get any result.
View 11 Replies
View Related
Oct 6, 2011
I got a RSV4000 router here with the latest firmware 1.3.3.5, trying to get the quick VPN client to connect.As far configurations go I have under WAN set the IP, subnetmask, DNS1, DNS2 and gateway. And under VPN I have created a client account with a password, created and then exported the Cert to my client PC.But when I attempt to connect, the QuickVPN software hangs for a few moments at "Connecting" and then fails; when the general error.I'm running this on Windows 7 x64.
View 1 Replies
View Related
Apr 18, 2010
I'm trying to connect through a VPN to RVS4000 router that I have VLAN'ed into two seperate networks 192.168.1.x (default) and 192.168.77.x. When i connect with the QuickVPN Client, I have no problems seeing devices on the 192.168.1.x network but i can't see the 192.168.77.x devices; so i'm assuming that the QuickVPN client software puts me on the default network and not the "77" network. Thing is, i only want to VPN into the "77" network and not the 192.168.1.x network.
Will QuickVPN allow me to do this? If not how do I VPN into the 192.168.77.x network?
View 4 Replies
View Related
Sep 21, 2011
Today I purchased a RV042 wired router. I set the VPN connection but when I try to login using QuickVPN, get stucks in "Verifying network". I checked the logs:
2011/09/22 20:43:45 [STATUS]OS Version: Windows 7
2011/09/22 20:43:45 [STATUS]Windows Firewall Domain Profile Settings: ON
2011/09/22 20:43:45 [STATUS]Windows Firewall Private Profile Settings: OFF
[Code]...
From my side Im connected to a WRT54G2. VPN Passthrough enabled. Windows 7 Pro x64. No 3rd party AV or firewall. Windows Firewall disabled, also tried enabling it.
From the RV042 side it has a Static IP Address configured. DHCP server enabled. HTTPS enabled. UPnP disabled. L2TP disabled.Firewall disabled. Block WAN Requests disabled.
View 6 Replies
View Related
May 6, 2013
We are having problems with using QuickVPN to connect to our RV220W.Sometimes it works, and sometimes it doesn't. There doesn't seem to be any rhyme or reason to it. [code] The firmware version is 1.0.3.5.
View 1 Replies
View Related
Jun 28, 2011
I have router Linksys RV042 v1.2 with latest firmware Version: 1.3.13.02-tm. And I'm using QuickVPN v 1.4.1.2. I've setup VPN connection with values, below: But every time I'm trying to connect to router by VPN it always popup a window "Remote Gateway not responding".It occurs when I'm trying to connect to VPN behind other router, when I'm connected directly to Internet the connection is established.But I'm connecting to other networks using VPN and it's working properly (behind the same router), so I think it's problem with RV042 configuration but I don't now weher.
View 5 Replies
View Related
Oct 1, 2012
I've been working on getting a client to Gateway configuration going for quite some time now. Had it working with a different Cisco single wan router that failed. The user replaced the router with an RV042 and we are trying to get the QuickVPN to once again connect to the router as it did before the replacement. Previously we did connect successfully with Windows 7 clients.
Router: RV042 v3 firmware 4.0.4.02-tm Quickvpn version 1.4.2.1
what i keep getting in the log is the following :
2012/10/02 12:55:07 [STATUS]OS Version: Windows Vista
2012/10/02 12:55:07 [STATUS]Windows Firewall Domain Profile Settings: ON
2012/10/02 12:55:07 [STATUS]Windows Firewall Private Profile Settings: ON
[Code].....
View 5 Replies
View Related
Sep 11, 2011
I have a RV082 in the corporate office, and several remote people connecting to it using QuickVPN through a variety of clients (XP and Windows 7). As of today, they are all now seeing the "Remote Gateway is not responding - disconnect or wait" message. Checking through the logs on some of the remote clients, I see the "Failed to ping the remote router" message several times, followed by the "Ping was blocked, which can be caused by an unexpected disconnect." message.
The odd thing is that everyone has been running very well over the past 2-3 weeks - most people with 8+ hours of solid connectivity. We made no changes to the clients, nor to the remote router in the corporate office.
View 3 Replies
View Related
Oct 11, 2011
I just bought a RV220W for my small company. I have read everywhere that this model come with 25 license for QuickVPN/IPsec.But when I tried to create all my account I had a bad surprise. The firmware tell me that the maximum number of user that I can create is 10! I dont see anywhere in the firmware where I can upgrade for another licence. I have the last firmware.
View 7 Replies
View Related
Oct 11, 2011
When I use QuickVPN under XP, I connect to my RVS4000 without problems. When I switch to new computer running Windows 7 and V4.2.1 QuickVPN I can get all the way to Verifying Network. Then I get the message that: "The remote gateway is not responding. Do you want to wait?" - repeatedly. The icon in the tool bar remains with a red slash and I am unable to ping devices on the lan side of the router. However, when I check the VPN Summary on the router, I see that it thinks I'm connected. When I check the VPN log I see that I am not:
Oct 12 10:27:53 - Configuration changed!
Oct 12 10:28:33 - Configuration changed!
Oct 12 10:28:34 - [VPN Log]: added connection description "ValR_rw_rw"
[Code]....
I've disabled MS Security Essentials and made sure the Firewall is on. IPSec Policy Agent and IKE and AuthIP IPSec Keying Modules services are both started. I've created a rule to allow QuickVPN throught the firwall in and out and a rule to let traffic on 443 and 60443 UDP and TCP through the Firewall.
View 19 Replies
View Related
