I've deployed a WRVS4400N router at one of my clients, however I'm unable to access resources on his network via DNS. I was hoping to use the router for DNS resolution, however when I connect via VPN, I can only connect to shares via IP address.
View 1 RepliesI have a new WRVS4400N VPN router and have set it up for VPN. On a separate computer I have a Verizon EVDO card so I have used that with a separate computer to access the internet on a public, routable IP address off of my network.
When I use the QuickVPN client, I wasn't able to get into my network (using ddyns.org) because I didn't have the "BLOCK WAN REQUEST" setting disabled so the router could be ping'd. Once I did that, I verified I could successfuly ping my ddyns name abc.xyz.com.
In the error log of the QuickVPN client, I still see:
2009/10/24 16:57:15 [STATUS]OS Version: Windows XP2009/10/24 16:57:16 [STATUS]Windows Firewall is OFF2009/10/24 16:57:16 [STATUS]One network interface detected with IP address x.x.x.x2009/10/24 16:57:16 [STATUS]Connecting...2009/10/24 16:57:16 [STATUS]Connecting to remote gateway with IP address:x.x.x2009/10/24 16:57:28 [WARNING]Remote gateway wasn't reached...2009/10/24 16:57:36 [STATUS]Remote gateway was reached by https ...2009/10/24 16:57:36 [STATUS]Provisioning...2009/10/24 16:57:47 [STATUS]Tunnel is configured. Ping test is about to start.2009/10/24 16:57:47 [STATUS]Verifying Network...2009/10/24 16:57:51 [WARNING]Failed to ping the LAN IP of the remote VPN Router!2009/10/24 16:57:52 [WARNING]Failed to
[code]....
I HAVE been able to make the connection successfully without any other changes to the environment. It's hit or miss, but usually a miss. Restarting QuickVPN sometimes works on the next try, but then fails if I disconnect and try again. Even when that ping error message is appearing, I am able to ping the host name at a command prompt without a problem.
Is something else on the router possibly blocking the ping requests?My router is behind a Westell F90 6100 DSL modem operating in bridge mode. The 4400 is obtaining the WAN address from Verizon(DSL) and that is also where I have my PPOE info entered to obtain the internet connection.
I have a RV180 router and i am trying to use the Quick VPN Client version 1.4.2.1. It works fine on my Windows 7 pc, and worked successfully once on the windows XP sp3 pc. But now the XP pc will not work.
What looks strange is in the VPN Client Connection Status on the router I see the status is Online, however the XP pc will not ping anything on the network or connect to the RDP pc i want. The QuickVPN Client hangs on "Verifying Network".
I tried the suggestions i saw online:
Disabling Firewall
Enabling Firewall
Making user name shorter
Allowing for PING on WAN (replies all come back fast)
Reboot Router
Upgraded firmware to 1.0.1.9
I did not adjust the MTU rate as i was not sure what to change it too. AV is AVG 2012.
I am trying to connect with QuickVPN to my RVS4000 in another location. I get this message: "The remote gateway is not responding. Do you want to wait?'
View 15 Replies View RelatedWe have 2 remote locations that are connecting to a server at our home location. Each remote computer uses quickvpn utility to establish a vpn with the home location. Our problem is that sometimes the vpn disconnects while we are working in remote desktop on server 2008. Luckily our sessions in remote desktop stay put but we lose the vpn connection. Most of the time we get a message that the remote gateway is not responding. Our dsl internet connection seems to work and we have previously had no trouble with connecting to the home location. We have 3 computers that connect simultaneously to the server at each remote location and sometimes one computer will stay connected while others disconnect.
View 3 Replies View RelatedI'm attempting to configure remote management (and, sometime soon, SNMP) for a newly-deployed WRVS4400N v.2.At the Basic Settings page, I enabled Remote Management, and left the port # at the default. Remotely I entered the public (static) IP for the router in the address bar of IE8 similar to this: 67.203.???.??:8080. IE8's response is, "The webpage cannot be displayed." I'm using a public wi-fi access point, and don't know how the local router is configured, so it's possible that the local router has a blocking rule in the firewall.I'll try again using another remote router that I manage.
View 3 Replies View RelatedHardware: WRVS4400N on Firmware version: V2.0.2.1-ETSI
Quick VPN Version 1.4.2.1 on Windows7 Ultimate 64bit.
QuickVPN Client stopps with: Verifying Network.... and "The remote gateway is not responding. Do you want to wait? Yes / No"
Here we go with the log:
2011/10/24 09:09:06 [STATUS]OS Version: Windows 7
2011/10/24 09:09:06 [STATUS]Windows Firewall Domain Profile Settings: OFF
2011/10/24 09:09:06 [STATUS]Windows Firewall Private Profile Settings: OFF
2011/10/24 09:09:06 [STATUS]Windows Firewall Private Profile Settings: OFF
2011/10/24 09:09:07 [STATUS]One network interface detected with IP address 192.168.11.106
[code]....
Additional I can ping to dirkle.dyndns.org as well as accessing to the WRVS4400N [URL] The connection map is as following:
Client --> PPPoE DSL Router --> (...INTERNET...) --> NetvigatorGateway ---> WRVS4400N --> HomeNetwork
The NetvigatorGateway is locatet at my home and also distributing IP-TV. For internet it netvigator gateway is set DMZ to WRVS4400N (network 192.168.1.xxx); the WAN IP is assigned to the WRVS4400N and same as on dirkle.dyndns.org. When I connect myself into the netvigator gateway, (network 192.168.8.xxx) i can successfully establish a VPN connection with QuickVPN to the WRVS4400N.But then, what reason ever, I cannot access to 192.168.1.xxx network devices. QuickVPN does not allow me to see the assigned IP as well. This is my issue 2: After the connection is "successfully" established, it does not feel as I am part of the home network....Issue 3 would be: In the company we use CiscoAnyConnect VPN client (Verison 2.4.0202). Is it possible in using this client instead in any later firmware revision?
I am trying to setup VPN with WRVS4400N and Quick VPN on client side. I am fairly new to VPN and did some research and looked through the manual but can't seem to get it to work so far and from what I noticed many people are having this problem.
Basically it gives the "Failed to establish connection" generic error, shows it almost instantly.It also showed the certificate error before but then I read about putting it in the installation directory and it stopped showing it, and whats strange is later I removed it but it doesnt show the error any longer, so don't know if its caching it somewhere or what can be going on...
In effort to look for answer and test things out I tried to connect to another location and setup a WRV200 router, I also get the same error but not instantly, it even shows "Activating Policy" but then doesn't go farther and shows the generic error.Also with this setup strangly it always shows the certificate error, no matter if I put one in directory or not... Even tried to name it as the WRVS4400N certificate name...
Anyway VPN IPSec is disabled, and Client Accounts are configured and changed password several times to make sure its correct, VPN Passthrough enabled on all 3 options. I tried to disable Windows Router, I also have a router in place do I possibly need to open some type of ports for the QuickVPN client?
I use RDP extensively on my LAN to use and manage 4 PCs running Win XP or Win7. My consumer-grade Cisco Linksys WRT610n crapped out after less than 2 years, so I thought I'd try the Cisco WRVS4400N to gain extra features like VPN. I have not enabled anything new on the router except for adding a second wireless SSID for guest use, although no bandwidth management or VLANs have been set up yet. Firmware version is 2.0.0.8.Since installing this router I have been unable to use Windows RDP on ANY of my computers on the LAN, whether I use the machine name or the IP address. I can ping every device on my network - print servers, NAS boxes, PCs, but no RDP. WHAT'S GOING ON?
View 6 Replies View RelatedRouter is a version 1.1 running with sw version V1.1.13-ETSI
Quick VPN is sw version Ver 1.4.1.2
The issue is that I can't connect due to that i cant ping the internal IP, get this error message in the QVPN log [WARNING]Failed to ping remote VPN Router![URL]I have disable the "Block WAN Request" and it is possible to ping the router on the external site.So as I see it, the router blocks for ping on the internal IP via QVPN, what have I done wrong?
I bought a router Cisco WRVS4400N Wireless-N Gigabit Security Router - VPN v2.0 with the intention of using with the Quick VPN Client for connecting to my home network.
My home network is connected to a pre provide by my ISP Thomson TG784 and is connected to it but all my main network is controlled by the WRVS4400N, I have forward all the doors, as you can see by the log part below, and by analyzing the log you can see that I can't get any PING to complete the VPN connection.
OS is windows 7
QuickVPN Clien is 1.4.2.1
WRVS4400N firmware is v2.0.2.1
Thomson TG784 firmware is 8.4.2.Q
Log from Quick VPN
2012/01/11 19:44:03 [STATUS]One network interface detected with IP address 192.165.0.196
2012/01/11 19:44:03 [STATUS]Connecting...
2012/01/11 19:44:03 [DEBUG]Input VPN Server Address = husportugal.dnsalias.com
[code]....
Log from WRVS4400N
Jan 15 10:12:53 - [VPN Log]: added connection description "Casa_rw_rw"
Jan 15 10:12:54 - [VPN Log]: listening for IKE messages
Jan 15 10:12:54 - [VPN Log]: forgetting secrets
[code]....
Im having trouble with getting my VPN to work on my brand new WRVS4400N router. i cant find the solution to my problem, no matter how much i read about it.
WRVS4400N:
Firmware Version: V2.0.0.8-ETSI
QuickVPN:
Version: 1.4.1.2
The laptop im trying to connect to the gateway via VPN is a Windows 7 x64 HP Elitebook 8540p with a internal mobile broadband (HSPA+)So.The scenario is that i've installed the QuickVPN client on my Win7-machine without any trouble.I've created a user in the web-administration of the router.The router is configured to disable "Block WAN requests" in the firewall, apart from that the firewall is on.When trying to connect - with a valid certificate that i created, i get a error message after the dialog telling me "Verifying network":"The remote gateway is not responding. Do you want to wait?".
The log.txt tells me:
...2010/10/06 00:00:28 [STATUS]Verifying Network...2010/10/06 00:00:34 [WARNING]Failed to ping remote VPN Router!2010/10/06 00:00:37 [WARNING]Failed to ping remote VPN Router!2010/10/06 00:00:40 [WARNING]Failed to ping remote VPN Router!2010/10/06 00:00:43 [WARNING]Failed to ping remote VPN Router!2010/10/06 00:00:46 [WARNING]Failed to ping remote VPN Router!2010/10/06 00:00:49 [WARNING]Ping was blocked, which can be caused by an unexpected disconnect.2010/10/06 00:02:13 [STATUS]Disconnecting...
[code].....
what exactly is QuickVPN?Is it a IPSec VPN?Is it a PPTP?Is it a SSLVPN?can I resolve my local hostnames? That means, can I configure a lokal DNS Server?
View 3 Replies View RelatedThe PPTP client from Windows 7 is not working with this router; therefore I would like to try the quickvpn.Is there any paper from Cisco explaining how to setup the RV120W for quickvpn ?
View 1 Replies View RelatedSo have a RV042 VPN router that is directly connected to the ethernet port of our comcast cable modem.
If I connect to it using QuickVPN (1.4.2.1) from a PC that is connected using AT&T 3G Network it works fine!
If I connect to it using QuickVPN (1.4.2.1) from a different PC that is connected using home WiFi (linksys wrtxxx) then it fails. In the VPN log all I see is failure messages for ping.
2011/10/22 15:47:28 [WARNING]Failed to ping remote VPN Router!
If I open a regular command prompt and attempt to ping the VPN router it works so not understanding why the QuickVPN is unable to ping.
how I can troubleshoot this further. Makes me think the RV042 config is fine otherwise it would not work on a 3G connection. Something on the home PC or the home network. Not sure what to check.
I've one RV042. I've configured VPN PPTP and it work (I've redirect port 1723 on router1 to rv042). If I can try to use quickVpn, client login and receive error "remote gateway is not responding". I have redirect port 60443 from router1 to rv042. Connection it's this: INTERNET-router1-RV042.
View 3 Replies View RelatedI have been battling with my Cisco RV120W router and QuickVPN.Running Windows 7 Home PremiumPerformed a fresh install to factory out-of-box install for WindowsRemoved NortonDid NOT perform any windows updatesInstalled QuickVN version 1.2.4.1I have updated the firmware to the latest version (confirmed by cisco)I can connet to the router and have a stable connectionI can ping both the router IP and the shared file server IPWhen I enter the shared file server IP into the search field (e.g. \192.168.100.199) and press enter, I see a connection to "share", so I click on this and then see "FolderName" of my shared files. I click on this folder and I get a timed out error.When I enter the routers IP address into a browser (IE8 as factory installed) I get a timed out error also.In the past, I have installed all important and recommended updates for Windows and still get the same scenerioI have called cisco support and went through router settings, assigned them a VPN username, they log in and can access the files without issue (What the @#$$@#$)Cisco support spent plenty of time with me, but since they could access my network and since I could ping my devices, they had no other suggestions further.
I have this fresh factor out-of-box install. I know this is most likely something to do with my laptop that I am trying to use to connect to the network. I have Frontier as my ISP for home. I don't know if there is anything they are doing to interfere with my connection. I have tried to connect to the network via ComCast as well, with no luck.tell me if there is something I need to tweak in my Windows 7 settings?
I have a Cisco RV120W connected to the internet. I have configured a QuickVPN user on the router, but I cannot connect via QuickVPN no matter on what PC I try (with firewall or without firewal, Windows XP, 7, ...). On the router it says the VPN user is connected, but on the client PC I receive remote gateway not responding. In the logs it says failed to ping remote VPN router. I tried changing all settings I could find on this forum, but the result stays the same (changed port to 60443, deleted all IKE and VPN policies, allowed ping, disabled fragmented packets etc...). None of all the settings seems to get any result.
View 11 Replies View RelatedI got a RSV4000 router here with the latest firmware 1.3.3.5, trying to get the quick VPN client to connect.As far configurations go I have under WAN set the IP, subnetmask, DNS1, DNS2 and gateway. And under VPN I have created a client account with a password, created and then exported the Cert to my client PC.But when I attempt to connect, the QuickVPN software hangs for a few moments at "Connecting" and then fails; when the general error.I'm running this on Windows 7 x64.
View 1 Replies View RelatedToday I purchased a RV042 wired router. I set the VPN connection but when I try to login using QuickVPN, get stucks in "Verifying network". I checked the logs:
2011/09/22 20:43:45 [STATUS]OS Version: Windows 7
2011/09/22 20:43:45 [STATUS]Windows Firewall Domain Profile Settings: ON
2011/09/22 20:43:45 [STATUS]Windows Firewall Private Profile Settings: OFF
[Code]...
From my side Im connected to a WRT54G2. VPN Passthrough enabled. Windows 7 Pro x64. No 3rd party AV or firewall. Windows Firewall disabled, also tried enabling it.
From the RV042 side it has a Static IP Address configured. DHCP server enabled. HTTPS enabled. UPnP disabled. L2TP disabled.Firewall disabled. Block WAN Requests disabled.
I have router Linksys RV042 v1.2 with latest firmware Version: 1.3.13.02-tm. And I'm using QuickVPN v 1.4.1.2. I've setup VPN connection with values, below: But every time I'm trying to connect to router by VPN it always popup a window "Remote Gateway not responding".It occurs when I'm trying to connect to VPN behind other router, when I'm connected directly to Internet the connection is established.But I'm connecting to other networks using VPN and it's working properly (behind the same router), so I think it's problem with RV042 configuration but I don't now weher.
View 5 Replies View RelatedI did upgrade to WiSM from v5.1 to V6 then i see this log %WCP-3-KEEPALIVE_LOST: wcp_controller_server.c:1763 Lost keepalives from Cat 6K Supervisor.
View 6 Replies View RelatedI've been working on getting a client to Gateway configuration going for quite some time now. Had it working with a different Cisco single wan router that failed. The user replaced the router with an RV042 and we are trying to get the QuickVPN to once again connect to the router as it did before the replacement. Previously we did connect successfully with Windows 7 clients.
Router: RV042 v3 firmware 4.0.4.02-tm Quickvpn version 1.4.2.1
what i keep getting in the log is the following :
2012/10/02 12:55:07 [STATUS]OS Version: Windows Vista
2012/10/02 12:55:07 [STATUS]Windows Firewall Domain Profile Settings: ON
2012/10/02 12:55:07 [STATUS]Windows Firewall Private Profile Settings: ON
[Code].....
I have a RV082 in the corporate office, and several remote people connecting to it using QuickVPN through a variety of clients (XP and Windows 7). As of today, they are all now seeing the "Remote Gateway is not responding - disconnect or wait" message. Checking through the logs on some of the remote clients, I see the "Failed to ping the remote router" message several times, followed by the "Ping was blocked, which can be caused by an unexpected disconnect." message.
The odd thing is that everyone has been running very well over the past 2-3 weeks - most people with 8+ hours of solid connectivity. We made no changes to the clients, nor to the remote router in the corporate office.
I just bought a RV220W for my small company. I have read everywhere that this model come with 25 license for QuickVPN/IPsec.But when I tried to create all my account I had a bad surprise. The firmware tell me that the maximum number of user that I can create is 10! I dont see anywhere in the firmware where I can upgrade for another licence. I have the last firmware.
View 7 Replies View RelatedWhen I use QuickVPN under XP, I connect to my RVS4000 without problems. When I switch to new computer running Windows 7 and V4.2.1 QuickVPN I can get all the way to Verifying Network. Then I get the message that: "The remote gateway is not responding. Do you want to wait?" - repeatedly. The icon in the tool bar remains with a red slash and I am unable to ping devices on the lan side of the router. However, when I check the VPN Summary on the router, I see that it thinks I'm connected. When I check the VPN log I see that I am not:
Oct 12 10:27:53 - Configuration changed!
Oct 12 10:28:33 - Configuration changed!
Oct 12 10:28:34 - [VPN Log]: added connection description "ValR_rw_rw"
[Code]....
I've disabled MS Security Essentials and made sure the Firewall is on. IPSec Policy Agent and IKE and AuthIP IPSec Keying Modules services are both started. I've created a rule to allow QuickVPN throught the firwall in and out and a rule to let traffic on 443 and 60443 UDP and TCP through the Firewall.
have a Cisco RV120W and I need setup a Quick VPN user, however i can't enable this user.I have Remote Management enable, access type All Ip Address and port number 443.
View 3 Replies View RelatedI want to ask if is possible to configure the RV180 behind my DSL Router to connect using QuickVPN. First I tried to connect to the PPTP server and worked fine, but when I tried to connect using QickVPN, seems to connect but when the client says "verifying network" after a while appears the message "network not responding..."
In my DSL-Router forwared this ports: UDP: 500,4500,443,60443 - TCP: 443,60443 (i don't know if tcp ports are needed but I opened for testing) and allowed protocol ESP (comes with the rule to allow IPSEC-L2TP)
I am trying to install a Cisco VPN Router RV120W behind this router. I have setup the Cisco and can access the internet from the device. I also setup the Actiontec router with the DMZ host as the Cisco router. When I try to connect to the VPN tunnel however I connect but receive an "Gateway is not responding" error message after 30sec. Is there anything else I need to setup on the actiontec router to allow VPN passthough or something like that?
Actiontec Lan IP: 192.168.1.1
Cisco Wan IP: 192.168.1.2
Cisco Wan SN: 255.255.255.0
Cisco Wan Gateway: 192.168.1.1
Cisco WAN DNS: 192.168.1.1
71.250.0.12
Cisco Lan IP: 192.168.20.1
Edit: I have also tried this connection from a Windows 7 Pro with Firewall enabled and also Windows XP with the same error.
Quick VPN log:
2011/12/30 00:05:58 [STATUS]OS Version: Windows 7
2011/12/30 00:05:58 [STATUS]Windows Firewall Domain Profile Settings: ON
2011/12/30 00:05:58 [STATUS]Windows Firewall Private Profile Settings: ON
2011/12/30 00:05:58 [STATUS]Windows Firewall Private Profile Settings: ON
2011/12/30 00:06:10 [STATUS]OS Version: Windows 7
2011/12/30 00:06:10 [STATUS]Windows Firewall Domain Profile Settings: ON (code )
I have a problem with my RV110W router. I would like to setup Quick VPN access. Manual is quite straightforward: enable management, create users, install client and that's all, should be working. But NOT. it does not work.
Remote Management is enabled on port 8080. Should it be changed to 443 as required for QVPN? Or it does not matter. Is it ok, to have management on 8080 and QVPN on 443?
I have tried to connect via QVPN Client ver. 1.4.1.2. Of course ip as well as user and pass has been changed. I tried to change management port to 443, but first:
1. i was not able to access management console at all
2. QVPN - still did not work
Using QuickVPN from one RV220W to another RV220W I cannot access the Webpage of the remote router. Goes to "CERTIFICATE NOT VALID" then click through that, and the the login page will not come up. Sceen flashes a hint of blue background, then turns white, then just sits there saying "Waiting for response from ???.???.QuickVPN will sucessfully connect and I can use all computers behind the router. Just cannot access the Webpage of the remote router. I can access the Webpage of the local router.Also, when I hookup using QuickVPN from an "Internet Cafe" that is using a Netgear router. I can then access the webpage on both remote routers (of course, depending on whom I QuickVPN'd into at the time).
Location #1
Office #1
RV220W: RV220W-A-K9-NA SER: SER15140314Firmware: 1.0.3.5
IP: 192.168.63.1
Location #2
Office #2
RV220W: RV220W-A-K9-NA SER: SER151600R2
Firmware: 1.0.3.5
IP: 192.168.2.1
I have called Cisco on this with no luck. They said to update my JAVA. I am currently JRE 6 Release 30 and still no luck. The Log files reveal nothing and are darn near unreadable since there is no line breaks in the log file. Have to manually edit the log to pick stuff out.
I want to connect from a Linux station to RV082, is it possible? What software can I use and with what configuration?
View 2 Replies View RelatedI have a doubt. What I have to configure in my RV180 to make a VPN connection with Qvpn client. I created the user and if try to connect from the client I've recieved the message that is connected, but if I try to ping the RV180 local ip answer, but if I try to ping any other IP address of the VPN I can't. I think I would have something misconfigured but I don't know what is it.
View 4 Replies View Related