I bought a router Cisco WRVS4400N Wireless-N Gigabit Security Router - VPN v2.0 with the intention of using with the Quick VPN Client for connecting to my home network.
My home network is connected to a pre provide by my ISP Thomson TG784 and is connected to it but all my main network is controlled by the WRVS4400N, I have forward all the doors, as you can see by the log part below, and by analyzing the log you can see that I can't get any PING to complete the VPN connection.
OS is windows 7
QuickVPN Clien is 1.4.2.1
WRVS4400N firmware is v2.0.2.1
Thomson TG784 firmware is 8.4.2.Q
Log from Quick VPN
2012/01/11 19:44:03 [STATUS]One network interface detected with IP address 192.165.0.196
2012/01/11 19:44:03 [STATUS]Connecting...
2012/01/11 19:44:03 [DEBUG]Input VPN Server Address = husportugal.dnsalias.com
[code]....
Log from WRVS4400N
Jan 15 10:12:53 - [VPN Log]: added connection description "Casa_rw_rw"
Jan 15 10:12:54 - [VPN Log]: listening for IKE messages
Jan 15 10:12:54 - [VPN Log]: forgetting secrets
[code]....
Is it possible to telnet into the 'WRVS4400N Wireless-N Gigabit Security Router with VPN' router? When I try it says the remote system refused the connection.
i bought this router because I wanted a gigabit router for my small business and I figured whats better than a small business router? Well, one think I used pretty heavily on my Linksys WRG54GS was a simple port forward to my XP box for VPN. I know nothing about how to currectly set up VPN in this router. Does this router have a built in VPN server? Also, is there anyway to completely disable everything VPN side on this router and simply forward my port 1723 to my computer again? I am using this in conjunction with my android phone. I downloaded the AnnyConnect software, but yielded zero success. I have a working tun.ko installed on my rooted android phone, but this all is completely too much work for something that worked very well before using simple port forwarding and the built in vpn client on the phone. How can I correctly set up my router for the VPN to use with the AnnyConnect application I have on my cell phone?
Hardware: WRVS4400N on Firmware version: V2.0.2.1-ETSI Quick VPN Version 1.4.2.1 on Windows7 Ultimate 64bit. QuickVPN Client stopps with: Verifying Network.... and "The remote gateway is not responding. Do you want to wait? Yes / No"
Here we go with the log:
2011/10/24 09:09:06 [STATUS]OS Version: Windows 7 2011/10/24 09:09:06 [STATUS]Windows Firewall Domain Profile Settings: OFF 2011/10/24 09:09:06 [STATUS]Windows Firewall Private Profile Settings: OFF 2011/10/24 09:09:06 [STATUS]Windows Firewall Private Profile Settings: OFF 2011/10/24 09:09:07 [STATUS]One network interface detected with IP address 192.168.11.106
[code]....
Additional I can ping to dirkle.dyndns.org as well as accessing to the WRVS4400N [URL] The connection map is as following:
The NetvigatorGateway is locatet at my home and also distributing IP-TV. For internet it netvigator gateway is set DMZ to WRVS4400N (network 192.168.1.xxx); the WAN IP is assigned to the WRVS4400N and same as on dirkle.dyndns.org. When I connect myself into the netvigator gateway, (network 192.168.8.xxx) i can successfully establish a VPN connection with QuickVPN to the WRVS4400N.But then, what reason ever, I cannot access to 192.168.1.xxx network devices. QuickVPN does not allow me to see the assigned IP as well. This is my issue 2: After the connection is "successfully" established, it does not feel as I am part of the home network....Issue 3 would be: In the company we use CiscoAnyConnect VPN client (Verison 2.4.0202). Is it possible in using this client instead in any later firmware revision?
I am trying to setup VPN with WRVS4400N and Quick VPN on client side. I am fairly new to VPN and did some research and looked through the manual but can't seem to get it to work so far and from what I noticed many people are having this problem.
Basically it gives the "Failed to establish connection" generic error, shows it almost instantly.It also showed the certificate error before but then I read about putting it in the installation directory and it stopped showing it, and whats strange is later I removed it but it doesnt show the error any longer, so don't know if its caching it somewhere or what can be going on...
In effort to look for answer and test things out I tried to connect to another location and setup a WRV200 router, I also get the same error but not instantly, it even shows "Activating Policy" but then doesn't go farther and shows the generic error.Also with this setup strangly it always shows the certificate error, no matter if I put one in directory or not... Even tried to name it as the WRVS4400N certificate name...
Anyway VPN IPSec is disabled, and Client Accounts are configured and changed password several times to make sure its correct, VPN Passthrough enabled on all 3 options. I tried to disable Windows Router, I also have a router in place do I possibly need to open some type of ports for the QuickVPN client?
I have a Cisco SA520W router and needs to set up VPN. Du to major problems with the SSL VPN Client and windows 7, I had to let it go and try a different approach.
That was the QuickVPN client, but as it turs out, it simply impossible from reading the user manual to understand just how I have to set thing up. For instance, the VPN Wizard tells you to enter a preshared key. But in the QuickVPN Client, where do I enter the key?
And shall the "Enable Cisco VPN Client" be ticket off, I assumed yes, but seriously it is impossible to know.
Then in the VPN Wizard again, in the Remote & Local WAN Adress, what shall use FQDN or IP Address. The if FQDN, what shall a enter, the domain name for the router, whats the point in that? The domain name of the VPN Client, seriously, what's the point in that? I would assume that 99% of the VPN Client does NOT have a domain name. Then, if IP address, am I supposed to know the IP address of the client? Same with the "Secure Connection Remote Accessibility", what am I supposed to enter. The IP address which the Quick VPN Client network adapter shall have?
I've deployed a WRVS4400N router at one of my clients, however I'm unable to access resources on his network via DNS. I was hoping to use the router for DNS resolution, however when I connect via VPN, I can only connect to shares via IP address.
I am setting up remote access using an RV042 router. Using quickvpn or a client-to gateway vpn and shrewsoft client, I can only access/ping the LAN side of the remote router and one machine on the remote network. The PPTP server and native Windows 7 connection provide access to all machines on the remote network.I have 2 possible reasons for this and would like to find the real reason:
1) The remote RV042 is behind another router, and that router restricts access other than the PPTP traffic.
2) The VPN tunnels other than PPTP only allow access to the remote LAN side of the router and remote machines that have the remote router defined as their gateway in the IP configuration.
I have a new WRVS4400N VPN router and have set it up for VPN. On a separate computer I have a Verizon EVDO card so I have used that with a separate computer to access the internet on a public, routable IP address off of my network.
When I use the QuickVPN client, I wasn't able to get into my network (using ddyns.org) because I didn't have the "BLOCK WAN REQUEST" setting disabled so the router could be ping'd. Once I did that, I verified I could successfuly ping my ddyns name abc.xyz.com.
In the error log of the QuickVPN client, I still see:
2009/10/24 16:57:15 [STATUS]OS Version: Windows XP2009/10/24 16:57:16 [STATUS]Windows Firewall is OFF2009/10/24 16:57:16 [STATUS]One network interface detected with IP address x.x.x.x2009/10/24 16:57:16 [STATUS]Connecting...2009/10/24 16:57:16 [STATUS]Connecting to remote gateway with IP address:x.x.x2009/10/24 16:57:28 [WARNING]Remote gateway wasn't reached...2009/10/24 16:57:36 [STATUS]Remote gateway was reached by https ...2009/10/24 16:57:36 [STATUS]Provisioning...2009/10/24 16:57:47 [STATUS]Tunnel is configured. Ping test is about to start.2009/10/24 16:57:47 [STATUS]Verifying Network...2009/10/24 16:57:51 [WARNING]Failed to ping the LAN IP of the remote VPN Router!2009/10/24 16:57:52 [WARNING]Failed to
[code]....
I HAVE been able to make the connection successfully without any other changes to the environment. It's hit or miss, but usually a miss. Restarting QuickVPN sometimes works on the next try, but then fails if I disconnect and try again. Even when that ping error message is appearing, I am able to ping the host name at a command prompt without a problem.
Is something else on the router possibly blocking the ping requests?My router is behind a Westell F90 6100 DSL modem operating in bridge mode. The 4400 is obtaining the WAN address from Verizon(DSL) and that is also where I have my PPOE info entered to obtain the internet connection.
Is there a safe way to use the Cisco VPN Client (V5.x) and Cisco Quick VPN (V1.4.1.2) on the same Windows PC? I need to access my office RVS4000 and my customer's PIX 506 from the same laptop (but not at the same time).
Perhaps I should be asking "Is there a single Windows VPN client that works with both the Cisco RVS4000 and Cisco PIX 506? I have seen these questions asked on various forums but have yet to see a definitive answer.
I have a RV042 router setup with Client to gateway VPN access, and am connecting with a W7 PC running QuickVPN. We have many PC's that already have the standard CiscoVPN client on them, is it possible to configure the RV042 to allow these clients to conenct? I'm not sure how to get the Mutual authentication to work, or how to import the PEM certificiate into that client. It seems to allow it to import, but I can never select it.
I have a Cisco RV082 and can successfully connect with the Cisco QuickVPN Client, 1.4.2.1. However, after 1 to 5 minutes I see the Windows 7 bluescreen indicating that the system has halted due to a problem with a driver. I have installed the latest Windows updates and reinstalled the client.
The bluescreen only occurs if I use the Cisco QuickVPN Client.
The establishment of IPSEC tunnel between the RV220 and QuickVPN client works properly with the security certificate of origin of the router.RV220 V1.0.3.5QuickVPN V1.4.2.1
Since the establishment of a security certificate self-signed, the RV220 and QuickVPN client refuses to work together .
Here are the log of the QuickVPN client
2011/09/27 12:45:14 [STATUS]OS Version: Windows 7 2011/09/27 12:45:14 [STATUS]Windows Firewall Domain Profile Settings: ON 2011/09/27 12:45:14 [STATUS]Windows Firewall Private Profile Settings: ON 2011/09/27 12:45:14 [STATUS]Windows Firewall Private Profile Settings: ON
I recently purchased a WRVS4400N security router and have got a strange problem with it. I set it up as my main router and connected two computers (a desktop and a server) using DHCP. They both work fine, internet is as fast as it should be, no problems whatsoever. However, when I setup the Wifi SSID (whatever security options I use, same with open/wpa/wpa2) and connect my laptop to it. It is allocated a IP address and windows even says that there is an internet connection. As soon as I try to do anything though, I am dropped. Try to ping an outside server, failure and dropped. Open IE, failure and dropped. I cannot even access my local server connected by wire to the router.If I connect the laptop via a cable to the router everything works, and it continues to work when I unplug it. So this means that right now I walk over to the router and plug my laptop in for 3 seconds before I unplug it and then use the wifi for a couple of hours without any problem. But as soon as I try to turn on my wireless Logitech SqueezeBox or wireless printer, they fail and take my laptop with it..
I have:reset the router, used both firmware 2.0.2.1 and 2.0.1.3 and done a factory reset.Tried to move the router close to the laptop, no difference.
I have a RVS4000 router, and using Quick VPN client (latest version, 1.4.2.1?) on a computer with Windows Vista. I can connect to the router, and I can see computers, and drives on the network. When I click on a drive or computer, I can't connect to the devices. Local IP address are 192.168.1.x, remote is 192.168.2.x.
I recently installed a new RV120W router at one of my customer's office. I have 2 users connecting using the Quick VPN software.The first one is running on a Windows XP Pro SP3. Everything works great on this PC.The second PC is running on a Windows Vista - The QUICKVPN client stays at Veryfing Network and Eventually I get an error " The remote gateway is not responding. Do you want to wait?I have disabled Firewall on both PCS for troubleshooting purposes.
I have an Ethernet Loopback Plug (4 Pairs) made and trying to test the Gigabit Interface on a 3845 Router with a fail result. The interface will show up/up only if I set the interface to 100M/Full Duplex when I plug-in the Ethernet Loopback Plug (4 Pairs). I don't see this Gigabit Interface @ 3845 router has any option to set it to internal or external loopback.
Looking for a working Cisco VPN client for Windows 7. There seems to be an availabel download for a ver 5, but you have to be a reseller etc.. Where do I download the Windows 7 supported VPN client to access my WRVS4400N router? If none, should I use 3rd party - IF yes to 3rd party, which one would you suggest?
Quick VPN and have not had any success connecting with our router. Below is my components info. Cisco router: WRVS4400N, Firmware V2.0.0.7. The router is behind a Comcast SMC business gateway modem Remote computer: Window 7 Ultimate 64 bit
I downloaded the Quick VPN client 1.4.2.1, and installed the client successfully but cannot connect using the VPN Client Account that I had set up in the router. Below are several questions that I hope to understand.
1) Do I need to configure specific ports for VPN in the Comcast gateway firewall?
2) What IP address do I put in the Quick VPN client profile when I connect remotely? The WRVS4400N modem shows 2 IP addresses in the Status:
DNS1: 68.xx.xx.176 DNS2: 68.xx.xx.132
Are these the IP that go into the "Server Address" on the Quick VPN client profile? and which one of the two? or do I use the static WAN IP address provided by my Comcast account?
3) In the Quick VPN client window, what is the "Use Remote DNS Server" mean?
4) Do I need to create a client certificate from the WRVS4400N for the client
5) Is there any setup needed for the remote firewall (if the client is behind a home wireless router and modem, for example)?
I just bought a WRVS4400N last week to replace my existing LinkSys WRH54G. To my disappointment, I now have a problem that this router halts everytime any eMule/P2P client is connected for more than 15~30 minutes, no matter the uPNP is enabled or not, When it halts, the only thing to get it work is to unplug its power cable then back on. So, I then upgraded its firmware from 2.0.1.3 to 2.0.2.1, but the problem still persists. However, the truth is that this problem never happened on my WRH54G
We are looking for a solution to avoid VPNs to encrypt data between HQ and Bldgs (point-to-multipoint) Gigabit fiber(untrusted media).Is there any cisco's product providing layer2 encryption over Giga fiber?The HQ has a 6509s and remote bldgs have mixed of 3750s,4500s in trunks.
I just bought this router (4400N) at a retail store for $239.00 with a ship date of 12/2009 and the QuickVpn client will NOT work with Windows 7. Furthermore, I do not see any signs of Cisco fixing this.I would be happy if I could use the pptp and the MS Clients. There is no pptp option in the 4400N. All I can do is port forward to my MS server. This does work, but then I cant vpn out....Unfortunately, I will have to return this router for a "STORE CREDIT" . This product should be removed from the shelves and recalled until the client works with Vista and Windows 7 in any way or fashion.Yes, I did install the 1.3 version and I even tried it in compatibility mode for XP?
I'm running an Optiplex 330 with the Broadcom NetXtreme 57xx Gigabit ethernet card.
The computer is running Windows 7, 64bit, but there do not appear to be any drivers for that OS.I tried selecting Vista 64bit, but there were no drivers. The Vista 32bit doesn't work.
Then I went to Broadcom and found these drivers: [URL] the W764bit drivers didn't change the fact i'm still on a 100Mbit card (as seen on Local Area Connection Status screen and the Device manager)
I've got a short trouble running anyconnect client 2.3.254 under Mac OS X 10.5.6.If I use it to connect an ASA 8.0.4 through a proxy (squid) it doesn't work.If I use Win XP, with same proxy, it works.If I don't use any proxy, with my Mac OS X client (on another WAN access) it works too.So, is anyconnect client supported over proxy server on MAC OS X ???? or did I miss something ?
I have a ASA 5510 that uses Radius for Authentication. What I am trying to do is assign each user that logs into VPN to have a specfic static IP based on userid. I have about 30 to 50 users. I don't want to complicate this by having them select a different profile when logging into the ASA. What is a clean and simply way to assign user static ip and not use local database for login?
But I currently have a Linksys E3200 I bought in a moment of weakness after an evening of being pissed off at bricking my old WRT610N. (soft bricked, but I'm beyond screwing with it)
There's nothing *wrong* with it, but I am interested in something that either comes preinstalled with DD-WRT, or is well supported (ie easy to install on) by DD-WRT. I plan on selling the E3200 once I find something to replace it.
My requirements: -Gigabit -5 GHz (I have a file server/HTPC; I don't want to be limited to gigabit ethernet) -$150 or less (I know $150 is high, but I figure I'll get close to that for the E3200)
I have that red gigabit router with the 150/65 service. It connects via ethernet for internet and has a coax to transmit the guide data etc.So my idea was to just leave the Verizon router connected and on (with wi-fi off) so it could do the TV stuff and just plug my router into the ethernet wall port the Verizon guy installed.Not so easy of course, my E4200 will not recognize the ethernet from my ONT (I think that's what the device they put in my basement is called) and the internet doesn't work. I have factory reset the router.The reason I am doing all this is because the wireless range of the e4200 at 2.4ghz is near unmatched and given my house, the actiontech cannot reach my room.
Is it possible to run the EA4500 as a Wired only Gigabit router? To do this do I just go into the settings and disable both the 2.4 and 5 channels or do I have to do something else?
