Is it possible to telnet into the 'WRVS4400N Wireless-N Gigabit Security Router with VPN' router? When I try it says the remote system refused the connection.
View 5 RepliesI just purchased a WRVS4400N Wireless-N Gigabit Security Router - VPN V2.0 and seem not to work with PPPoE from bluewin.ch ( Swisscom )
View 2 Replies View RelatedI bought a router Cisco WRVS4400N Wireless-N Gigabit Security Router - VPN v2.0 with the intention of using with the Quick VPN Client for connecting to my home network.
My home network is connected to a pre provide by my ISP Thomson TG784 and is connected to it but all my main network is controlled by the WRVS4400N, I have forward all the doors, as you can see by the log part below, and by analyzing the log you can see that I can't get any PING to complete the VPN connection.
OS is windows 7
QuickVPN Clien is 1.4.2.1
WRVS4400N firmware is v2.0.2.1
Thomson TG784 firmware is 8.4.2.Q
Log from Quick VPN
2012/01/11 19:44:03 [STATUS]One network interface detected with IP address 192.165.0.196
2012/01/11 19:44:03 [STATUS]Connecting...
2012/01/11 19:44:03 [DEBUG]Input VPN Server Address = husportugal.dnsalias.com
[code]....
Log from WRVS4400N
Jan 15 10:12:53 - [VPN Log]: added connection description "Casa_rw_rw"
Jan 15 10:12:54 - [VPN Log]: listening for IKE messages
Jan 15 10:12:54 - [VPN Log]: forgetting secrets
[code]....
i bought this router because I wanted a gigabit router for my small business and I figured whats better than a small business router? Well, one think I used pretty heavily on my Linksys WRG54GS was a simple port forward to my XP box for VPN. I know nothing about how to currectly set up VPN in this router. Does this router have a built in VPN server? Also, is there anyway to completely disable everything VPN side on this router and simply forward my port 1723 to my computer again? I am using this in conjunction with my android phone. I downloaded the AnnyConnect software, but yielded zero success. I have a working tun.ko installed on my rooted android phone, but this all is completely too much work for something that worked very well before using simple port forwarding and the built in vpn client on the phone. How can I correctly set up my router for the VPN to use with the AnnyConnect application I have on my cell phone?
View 1 Replies View RelatedWe have recently purchased SG 300-52Port Cisco Switch to support our Network but they constantly having some bizarre issues or I assume bugs, i.e. we cannot Telnet nor SSH to the switch now, whereas we were able to SSH before, we have set them up for Remote Log Services to get some syslogs and reports but no report have been generated nor logs,
I have done some testing through Wireshark and there are absolutely no reports / logs.We have some real issues with this switch and it’s hard to believe that this is a Cisco Product,
SG 300-52 Port Gigabit Managed Switch
Firmware Version (Active Image ) : 1.1.1.8
Firmware Version (Non-active ) : 1.1.0.73
Boot Version : 1.0.0.4
We are looking for a solution to avoid VPNs to encrypt data between HQ and Bldgs (point-to-multipoint) Gigabit fiber(untrusted media).Is there any cisco's product providing layer2 encryption over Giga fiber?The HQ has a 6509s and remote bldgs have mixed of 3750s,4500s in trunks.
View 2 Replies View RelatedI have installed a WRVS4400N router in a client's office. When laptops are plugged into the router everything works fine. When they are attached via the wireless signal it drops frequently. WPA personal is being used to encrypt. I have also installed the latest firmware and am having the same results. What can be done to eliminate the drops?
View 10 Replies View RelatedI have an ongoing problem with my WRVS4400N router. It reboots on it's own when streaming video through a wireless connection (computer, xbox, roku, tv). Once I make a wired conection, it performs flawlessly. The firmware is up to date. I have read some reviews of this router on Amazon stating the same problem, but I expected it to be solved with firmware update. Unfortunately, this was not the case.
View 4 Replies View RelatedI need trouble-shooting wireless network connectivity issues that arose recently:We use a Comcast modem and two WRVS4400N's as wireless routers/wireless access points.We recently got our comcast service upgraded to 100/20 and also got rid of our static ip address. As a result (I think there must be a sort of causal relationship here, but I'm not sure what it is) we can no longer connect to the internet using our wireless networks. We can connect to the wireless network, but have "No Internet Access."
View 4 Replies View RelatedI have several wired and wireless devices connected to the router which is running the latest firmware (2.0.2.1) and I have this issue with all wireless devices. The router is configured for B/G/N Mixed, Channel 6, and to broadcast the SSID. Security Mode is WPA2-Personal w/ key renewal set to 3600. Connection control is configured to allow only the desired MAC addresses. All wireless clients are configured for DHCP (as are some of the wired clients that do not have this issue). I have tried various setting changes over time, none of which have resolved the issue.
What I have determined, and may be useful, is that each time this occurs I am unable to ping the router from the client and have no connectivity to the internet or other devices on the network. If I ping the WAP address (reserved for internal use address) I get a response and then connectivity is always restored after doing so. In other words, I ping 192.168.1.1 and get no response, immediately ping 192.168.1.2 and get a response, then immediately ping 192.168.1.1 and now get a response and connectivity is restored. If I skip the first step and just ping the reserved address followed by the router address result is always the same. It would appear the issue is between the the two router addresses.
Prior to owning this router I had a Linksys BEFSX41 that I had for about 7-8 years and a WAP54G I had for about 5, both of which still worked and I never had this issue with my wireless clients. I went to this router for the increased performance and am very happy with that aspect, however this issue is unacceptable.
We have an office with about 10 PCs, and several other network devices (smartphones, printers, etc). Some PCs and printers are wired, some are not. About two weeks ago, some (6) of the wireless devices lost connectivity. Since then, some (4) of the devices have also recovered normal connectivity.
As of right now, there are two computers, a laptop and a desktop, that cannot use the wireless network. They see the wireless network, connect to it, receive an IP via DHCP properly, have correct DNS servers listed in ipconfig, but they can't ping the router, use the intranet, or internet.
I have what should be simple. Home network on cable. WRT320N is main router cabled to desktop with GB card. It is hard-wired to a Netgear WNR3500L (also gigabit). That router is hard-wired to a desktop with GB card. For testing I connected a second machine hard-wired to the WRT320N with a 10/100 card. All machines recognized cards properly at correct speed. I ran LAN Speed Test between machines. Speeds were comparable between machines regardless of cards. GB -> GB was mid-30's write, mid-80's read with GB -> 10/100 a couple of ticks slower but not significantly. The LED's on both routers will show different color if GB connection and both showed GB for the desktop connection but not the interconnect between the routers. The routers are connected at about 100' with CAT5E and straight-through.
View 5 Replies View RelatedWhat would be an acceptable number of wireless connections to a WRVS4400N router? I'm working in the IT department for a new company, and one of the offices complains that using VoIP and doing large file transfers are constantly a problem. They are all connecting wirelessly to the WRVS4400N. I managed to vpn in and connect to the web interface of the router, and it shows that there are 30 devices connected wirelessly to it. However, when people plug into the wall jack VoIP and data seem to work fine.I can't find any info on what a best practice would be for number of wireless connections to the router. There's no Vlans setup on it from what I can tell, so that may be my next step, to separate data and voice traffic.
View 2 Replies View RelatedI recently purchased a WRVS4400N security router and have got a strange problem with it. I set it up as my main router and connected two computers (a desktop and a server) using DHCP. They both work fine, internet is as fast as it should be, no problems whatsoever. However, when I setup the Wifi SSID (whatever security options I use, same with open/wpa/wpa2) and connect my laptop to it. It is allocated a IP address and windows even says that there is an internet connection. As soon as I try to do anything though, I am dropped. Try to ping an outside server, failure and dropped. Open IE, failure and dropped. I cannot even access my local server connected by wire to the router.If I connect the laptop via a cable to the router everything works, and it continues to work when I unplug it. So this means that right now I walk over to the router and plug my laptop in for 3 seconds before I unplug it and then use the wifi for a couple of hours without any problem. But as soon as I try to turn on my wireless Logitech SqueezeBox or wireless printer, they fail and take my laptop with it..
I have:reset the router, used both firmware 2.0.2.1 and 2.0.1.3 and done a factory reset.Tried to move the router close to the laptop, no difference.
I see a lots of problem associated with wirless connectivity with WRVS4400N, with following config
Firmware version - Firmware Version: V1.1.13
Wireless connectivity - G/N Mixed
Auth - WPA2 AES
Everything else default and AUTO,
Problem:The end devices suddenly drop connection. Wired connection works just fine. The DROPPED device can not be reconnected. On MAC I get AUTH time out. I see the SSID being broadcasted from my HTC wireless analyster so radio may not be the problem. I changed to set the speed to G only or N only but not avail. ONLY way to recover from this is rebooting the router.
Query regarding the Cisco WRVS4400N and Valet M10 routers. How to block the web interface (router login page) from wireless accessibility?
-Our Business is a hotel, so untrusted intruders are our guests.
-Our ISP seeks hotspot methods that we cannot implement.
-Our only solution is routers and an AP to extend internet wirelessly.
the login page or configuration page of the router is always accessible via the gateway address.if the gateway is 192.168.1.1, then a guest can just enter this address and try to guess the password. hacking tools add to the problem.the LAN is working but it is not of certification standards.I seek a way to block wireless access to the gateway login page or physical access only.
I've just purchased WRVS4400N VPN router and installed it. This was a replacement of a old Linksys router. After installing the router, I've started seeing wireless drops, packet drops and latency on pings. I've installed the latest firmware, disabled Firewall services, disabled IPS. No changes at all. As a basic example, I am pinging my NAS device (hard wired to router) from a laptop connected to wireless below. Previously while connected to my old linksys router the time was equal to no more than 2ms.
View 4 Replies View RelatedWhen clients connect wirelessly to the WRVS4400N they successfully get a DHCP address from the Windows 2008 server. After they have the address they can no longer access the server. It cannot be pinged, no drives can be mapped and internet access fails because the same server is running DNS. The WRVS4400N is setup for DCHP relay to the server. Wired clients do not have this problem. Wireless clients that connect to a secondary WAP on the same LAN also do not experience this problem. I have updated the router to the latest firmware version, reset it to factory defaults and reconfigured from scratch. Turning the server firewall off has not made any difference either. I have been able to bypass the internet problem by adding a second external DNS server in the DHCP scope options.
View 5 Replies View RelatedMy computer is not wireless so I have needed a wireless router from Time Warner. Directions tell me to connect to my computer. Will that solve the fact that my computer is not built in wireless?
View 2 Replies View RelatedI'm trying to telnet into the my RV180 router. How do I go about it.
I created 3 VLANS
1 at 192.168.1.1
20 at 192.168.20.1
30 at 192.168.30.1
Here is the Multiple VLAN Subnet Table:
1 192.168.1.1 255.255.255.0DHCP ServerEnabled 10192.168.10.1255.255.255.0DHCP Server Enabled 20 192.168.20.1 255.255.255.0 DHCP ServerEnabled
I can ping the router at all 3 IP addresses.How do I enable the telnet service on the router?
I am trying to access my RV042 through telnet. I go to http://192.168.1.1/sysinfo123.htm?ConsoleSimulation=1
which enables telnet. However when I type my username and password it will not authenticate.
I know this is a small business appliance I got my ccna certification with the hope of practice my CLI skills with a cisco device however I read in cisco docs the small business routers doesn´t support talnet neiter ssh I mean CLI, is thta true ?
View 1 Replies View RelatedI can telnet to switch from checkpoint firewall access port and from switch directly. I can ping/traceroute successfully to the switch. Access-lists 14 & 15 are allowing the traffic I want. The router on the other side of the FW has 2 static routes and a default static route set up.
Here is some of the config from my switch:service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryptionhostname xxxxx
enable secret xxxxxx
username xxxxxxxx password xxxxxxxip domain-name xx.xx.netaaa new-model
aaa authentication login default local enable line none[code].....
Not sure of checkpoint firewall config....I have run wireshark when trying to telnet and I get no syn-ack back from remote switch. Just 3 consecutive syn attempts.I have some switches I can connect to and they go right through the 3 way TCP handshake and I cannot find any differences in the configs between the successful connections and the unsuccessful connections.
I wish to change ARP table or any else to get a WOL functionnality.
I found how to activate telnet server, but I don't have the right login and password.
I have recently installed four Cisco RV042 v3 VPN routers for a customer of ours to replace existing Nortel Contivity 1010 devices which were providing VPN tunnels from the customer's 3 branches to their headoffice. The original Nortel devices were working perfectly but the customer wanted some firewall rule changes and the Nortels were proving to be somewhat inflexible and incomprehensible in their configuration hence why they were replaced.
When installing the Cisco routers I configured the VPN settings to match the Nortel device settings so that I could swap out a branch at a time without taking the whole setup down for a day.The customer has a Unix based dumb-terminal application running on a server at headoffice that they access from their branches using terminal emulators on Windows PCs and thin client hardware devices that support vt100 terminal emulation.
Prior to installing the Cisco RV042's everything was working fine. Now they are using the RV042's they keep getting the sessions from their branches dropped. Both PC users and thin client users are losing sessions and it happens with active and idle sessions. I have checked the logs on the routers when users are disconnected and there is nothing logged at that time (other than my login)... I had thought maybe it was to do with tunnel renegotioations so I have set to phase 1 / phase 2 SA timeouts to 86400 & 28800 seconds respectively but this has had no effect. I had also seen somebody advised disabling 'SPI' in the firewall... I have tried this and it makes no difference.
I have an Ethernet Loopback Plug (4 Pairs) made and trying to test the Gigabit Interface on a 3845 Router with a fail result. The interface will show up/up only if I set the interface to 100M/Full Duplex when I plug-in the Ethernet Loopback Plug (4 Pairs). I don't see this Gigabit Interface @ 3845 router has any option to set it to internal or external loopback.
View 2 Replies View RelatedI have small business server 2003 setup as a DC and did not install exchange, i use hosted exchange. i am trying to setup vpn and have opened port 1723 on both of my router. my network routes through a wireless router(192.168.1.1) (port 1723 forwarded to .1.104) to a second wireless router (192.168.2.1) to my server with two nic cards (.2.2 - external and .2.103 - internal) (port 1723 forwarded to .2.2) i can telnet 192.168.2.2 1723, .2.103, .1.104 - my ip of my second router handed by the first router. my server in handling dhcp and it is disabled on my .2 router. I CAN NOT telnet my public ip handed to 1.1 from the ISP(my internet IP). it tries for about 30 secs and dies.
View 8 Replies View RelatedI am having some troubles finding information about how to configure firewall policies (rules, chains, etc.) via telnet on a RV016. The reason for that is that i keep getting some log entries "connection refused - policy violation" and "blocked" even with my firewall wide open (only allow rules on all interfaces, SPI and block wan request disabled, multicast and https enabled, etc.... ). Also, with these exact same rules, i can only connect via PPTP with the firewall disabled. The minute i tick the enable option the tunnel never gets to authentication phase. I then started reading OpenRG manual and many things are quite similar, but some other entries are missing from that manual (maybe some changes made by cisco?). I am trying to figure out some service ids, chains (e.g. the rv016 has some rules redirecting to chains 10, 100, 200 but i can not find them anywhere), and so on. I have only one rv016 and about 60 connections to it so i can not experiment that much without having the whole company on my neck with internet problems.
View 2 Replies View RelatedI'm running an Optiplex 330 with the Broadcom NetXtreme 57xx Gigabit ethernet card.
The computer is running Windows 7, 64bit, but there do not appear to be any drivers for that OS.I tried selecting Vista 64bit, but there were no drivers. The Vista 32bit doesn't work.
Then I went to Broadcom and found these drivers: [URL] the W764bit drivers didn't change the fact i'm still on a 100Mbit card (as seen on Local Area Connection Status screen and the Device manager)
Right out of the box, the WRVS4400N [firmware v2.0.1.3] I just purchased says the WAN interface is DOWN; and it simply will not obtain an IP address from the Arris TM602G cable modem it is attached to. Internet still runs great on the old WRT54G. Is this WRVS4400 DOA? Or is there some arcane setting the quickstart guide overlooks? OR?
View 2 Replies View RelatedI'll just use the 4400n to provide DHCP to my two VLANs and then a new problem cropped up. I am unable to add a default route to the 4400n's DHCP server. It uses the 4400n's vlan IP as the default route. What I'm trying to ultimately achieve is to configure the 4400n as an access point for our "private" network on vlan1 and also "guest" access to the internet on vlan2.
View 12 Replies View RelatedI'm having problems trying to establish a IP Sec tunnel from the office to home. All of our machines are Macs so I have been using the directions described in "How to create an IP Sec tunnel for MAC Clients, A QVPN alternative" but I still can't get it to work. My setup is as follows:
The office is connected to the outside world through a MODEM (Sagemcom 2864 Connection Hub). This MODEM is also a wireless router. It's DHCP server provides addresses 192.168.2.x.The WRVS4400N's WAN port is connected to one of the LAN ports on the MODEM. It's IP address from the MODEM is 192.168.2.x. The WRVS4400N provides addresses 192.168.21.x to devices connected to it.We have a DynDNS account and are using the DDNS client on the WRVS4400N router to connect to it.At home, we have a DIR-655 router with IP Sec Passthru enabled. The router provides IP addresses 192.168.1.x for all devices connected to it. I am fairly sure there are no issues with the router setup at home since I am able to VPN into the office of my full-time job without any problems. I have tried just about everything I can think of but have not been able to get this to work. setting up the Local and Remote Group Settings on the WRVS4400N and the IP address settings in IP Securitas?
Ive setup a few WRVS4400N over the past 6 months, and have been receiving the below message from some of them every couple of hours.What does the message indicate?
View 1 Replies View Related