Cisco Routers :: RV042 V3 - How To Activate Telnet Server
Jan 25, 2012I wish to change ARP table or any else to get a WOL functionnality.
I found how to activate telnet server, but I don't have the right login and password.
ADVERTISEMENT
Cisco Routers :: Access RV042 Through Telnet?
Jun 20, 2011I am trying to access my RV042 through telnet. I go to http://192.168.1.1/sysinfo123.htm?ConsoleSimulation=1
which enables telnet. However when I type my username and password it will not authenticate.
Cisco Routers :: RV042 Can't Ping Ip Server
Feb 6, 2012i have setup vpn connection (client-gateway) using quick vpn ( default cisco) and third party like thegreenbow. connection is ok (established) but why from outside I can only ping to IP LAN PC , if I ping ip server the result is request time out(failed). I have been trying do this to 3 server ( windows server 2003 as OS).four your information I have made firewall "OFF" on all of those servers. the result is same, failed.
View 0 Replies View RelatedCisco Routers :: RV042 With Two Subnets For A Web Server?
Dec 21, 2011I have a static DSL connection and my ISP is giving me 4 static IP's. I have connected my RV042 to the DSL modem and I have now 1 subnet at 192.168.0.0. What I want to create is a WEB server/ Email server, but to sit on a different subnet - 192.168.5.0. For now I have connected the server to the DMZ port, but I am unable to to access it from WAN, only from LAN. How to configure properly the 2 subnets (192.168.0.0 and 192.168.5.0) and how to forward my static address to the server which I which to be on the 192.168.5.0.
View 4 Replies View RelatedCisco Routers :: RV042 Can't Locate DNS Server
Dec 14, 2012I'm trying to set up an RV042 as a gateway for our home network. I've cloned the MAC address of the cable modem attached to WAN1, and have set up WAN1 to obtain an IP automatically. The System Summary page shows under WAN Status that WAN1 has been assigned an IP address in the right range for Comcast, the provider. The default gateway address looks good, and the DNS server is, in fact, Comcast's main DNS server for this area.
However, when I go to System Management > Diagnostic, the router is unable to resolve basic domain names (e.g., www.cisco.com) or ping addresses outside the LAN. I can ping the router itself successfully. Attempts to access the web through the router fail on domain name look.
Cisco Routers :: RV042 Giving Out Certificate Instead Of Server?
Jan 28, 2013RV042 router is giving out the outer certificate instead of server certificate. Outlook anywhere is failing and we are receiving certificate errors for any secure site behind this firewall. I'm not talking about remote management. I'm talking about people trying to access our web site, which is secured, and getting an error because the RV042 is giving its own SSL certificate instead of the Server's certificate. Firmware Version: 1.3.13.02-tm. I don't see any updates for that hardware. I do have it working on an RV042 with the same firmware at a different location. How do we turn that off or keep it from happening? Output from a test site Attempting to resolve the host name xxxx in DNS.The host name resolved successfully. Additional DetailsTesting TCP port 443 on host xxxx to ensure it's listening and open. The port was opened successfully. Testing the SSL certificate to make sure it's valid. The SSL certificate failed one or more certificate validation checks. Test Steps ExRCA is attempting to obtain the SSL certificate from remote server xxxx on port 443. ExRCA successfully obtained the remote SSL certificate. Additional Details Remote Certificate Subject:
SN=California, L=Irvine, C=US, O="Cisco-Linksys, LLC", OU=RV042, CN=68:ef:bd:b8:0f:78, Issuer: SN=California, L=Irvine, C=US, O="Cisco-Linksys, LLC", OU=RV042, CN=68:ef:bd:b8:0f:78.Validating the certificate name. Certificate name validation failed. Tell me more about this issue and how to resolve it Additional Details Host name xxxx doesn't match any name found on the server certificate SN=California, L=Irvine, C=US, O="Cisco-Linksys, LLC", OU=RV042, CN=68:ef:bd:b8:0f:78.
Cisco Routers :: Multiple Internal Web Server RV042
Aug 15, 2012 We have setup a new internal web server so now we have two internal web server and both or hosting sites on port 80. Currently we have port 80 forwarding to one of the web servers and users are able to hit it from the outside.
Is there any way to configure the RV042 to route web traffic to the correct web server by using the site name or dns? If a user puts in the address{URL}, be routed to one web server but if they put in {URL}, be routed to our second web server. I've checked with our vendors and the both web servers applications need to run on port 80. If we have forwarding setup on the RV042 to forward port 80 to web1 then users can't access web2 from the outside?
Cisco Routers :: RV042 Giving Out Router Certificate Instead Of Server
Nov 28, 2012Just installed RV042 router. And it's giving out router certificate instead of server certificate so people who are trying to access our secured server are getting errors. I'm not talking about remote management. I'm talking about people trying to access our web site, which is secured, and getting an error because the RV042 is giving its own SSL certificate instead of the Server's certificate. How do we turn that off or keep it from happenning?
The RV042 firm version is v4.0.0.07-tm (Aug 19 2010 19:19:50)
Cisco Routers :: Configure RV042 Dual WLan / Web And DNS Server
Aug 19, 2011I need configuring Cisco RV042 dual wlan and port forwarding for 2 servers web and dns in LAN
View 1 Replies View RelatedCisco Routers :: RV042 Email Server Not Send Mail When Switch From Wan
Sep 28, 2011Just installed a RV042 with dual wan connections. Would like to make the WAN 2 (new cable modem as well) the primary connection over WAN1 (DSL), however whenever I switch from WAN1 to WAN2 in Smark Link set up, our email server will not send mail out, even though nothing is blocking the connection.
View 0 Replies View RelatedCisco Routers :: No Access Information Logged For PPTP Server On RV042?
Nov 25, 2012I have configured PPTP Server on RV042, and created 3 accounts. I am able to connect from Windows PC without any problems.
In the router's logging utility, there doesn't appear to be any log entries indicating either successful or failed attempts to connect to PPTP server. The only access logs I see are for access to the router's configuration utility. Is there a way to view PPTP access in the router system log?
Cisco Routers :: RV042 - DHCP Giving Out Wrong Default Gateway And DNS Server
Oct 3, 2012I have a RV042 router. The problem that I am having with it is that the DHCP is giving out the wrong Default Gateway and DNS Server. There is no option to change the DHCP server IP on any of the settings pages on the router. I am begining to think that there might not be a way to do it. I see that there is an option for the DNS under the DHCP page but the Public IP that is being handed out is not the one on that page. I also have 2 WAN connections hooked up as well a DSL link and a Cable link (the cable link is the primary one).
The following information is provided in an effort to resolve this issue:
IP of Router 10.0.0.2
IP of DHCP Server (the one that is being handed out):10.0.0.1
IP of DNS (the one that is being handed out): 10.0.0.11
What I want to it be.
IP of Router: 10.0.0.2
IP of DHCP 10.0.0.2
IP of DNS 10.0.0.2
Cisco Wireless :: WLC 5508 Not Able To Activate Internal DHPC Server
Sep 27, 2012I recently installed 2 wlc 5508 with the latest software 7.3.101.0. I am not able to activate the Internal DHPC Server. The following message appears: "Error in setting dhcp scop leasetime".
View 5 Replies View RelatedCisco Routers :: Unable To Activate Protect Link Web On RV220W
Jan 5, 2013I use to be running on firmware 1.0.2.4 with ProtectLink-Web working great, but then it expired. Some time later I updated the router to 1.0.4.17 and purchased a three year subscription to ProtectLink-Web, followed the registration link on the router, obtained an activation code, followed the activation link on the router and activated the service, however it didn't activate on the router.
I try to activate again and Trend Micro's site just says that it's already been activated. I contacted Trend Micro support and they see the activation attempts on there end and they said everything should be working. They recommended a factory reset which I performed and then attempted activation again, and again their site says that the service has already been activated. And yet when I go to Cisco ProtectLink Web > License > Summary it just says: "Please activate ProtectLink License to display the license information" and wont allow me to access the features. What is going on? Could the firewall be blocking the service? I didn't have this trouble the first time I used ProtectLink with f/w 1.0.2.4
Belkin Routers :: Unable To Activate Parental Control For F5D7231-4
Oct 28, 2012I'm trying to activate parental control for the F5D7231-4 (2000). When I go to the parental control screen, I only get a button to subscribe now (see image). When I click the button, I am sent to the Belkin UK website. I cannot find out how to get the parental controls activated on the U.S. site. I am running the latest firmware (F5D7231-4_US_5.01.11 ).
Update: I looked at the source code for the page in the router...it's referencing a website : [URL] that no longer seems to be valid. Or is this a problem in the firmware ?
Remotely Access 500 Switches Via TELNET And Web Based From Server?
May 15, 2013I want to remotely access Cisco 500 switches via TELNET and WEB BASED from a server. I dont know the ip addresses for Cisco 500 switches which are configured as backbone which the ip address assigned on the network is static ip address. Specifically I want to get their configuations inorder to get their specified assigned vlans on the network. I know the ip addresses for their specified cisco 500 switches' gateways. I know that cisco 500 switches can be accesses through web. Is there other ways to solve the problem apart from going onsite and connect to the cisco 500 switches using network cable since cisco 500 swithes dont have console ports?
View 1 Replies View RelatedCisco Routers :: How To Enable Telnet On RV180
Mar 9, 2013I'm trying to telnet into the my RV180 router. How do I go about it.
I created 3 VLANS
1 at 192.168.1.1
20 at 192.168.20.1
30 at 192.168.30.1
Here is the Multiple VLAN Subnet Table:
1 192.168.1.1 255.255.255.0DHCP ServerEnabled 10192.168.10.1255.255.255.0DHCP Server Enabled 20 192.168.20.1 255.255.255.0 DHCP ServerEnabled
I can ping the router at all 3 IP addresses.How do I enable the telnet service on the router?
Cisco Routers :: Telnet RV016 Not Supporting Cli
Jan 14, 2013I know this is a small business appliance I got my ccna certification with the hope of practice my CLI skills with a cisco device however I read in cisco docs the small business routers doesn´t support talnet neiter ssh I mean CLI, is thta true ?
View 1 Replies View RelatedRouters / Switches :: Still Not Able To Telnet / SSH To Switch?
Mar 14, 2011I can telnet to switch from checkpoint firewall access port and from switch directly. I can ping/traceroute successfully to the switch. Access-lists 14 & 15 are allowing the traffic I want. The router on the other side of the FW has 2 static routes and a default static route set up.
Here is some of the config from my switch:service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryptionhostname xxxxx
enable secret xxxxxx
username xxxxxxxx password xxxxxxxip domain-name xx.xx.netaaa new-model
aaa authentication login default local enable line none[code].....
Not sure of checkpoint firewall config....I have run wireshark when trying to telnet and I get no syn-ack back from remote switch. Just 3 consecutive syn attempts.I have some switches I can connect to and they go right through the 3 way TCP handshake and I cannot find any differences in the configs between the successful connections and the unsuccessful connections.
Cisco Routers :: VPNs Between RV042s (v3) Keep Dropping Telnet Sessions
Jan 26, 2012I have recently installed four Cisco RV042 v3 VPN routers for a customer of ours to replace existing Nortel Contivity 1010 devices which were providing VPN tunnels from the customer's 3 branches to their headoffice. The original Nortel devices were working perfectly but the customer wanted some firewall rule changes and the Nortels were proving to be somewhat inflexible and incomprehensible in their configuration hence why they were replaced.
When installing the Cisco routers I configured the VPN settings to match the Nortel device settings so that I could swap out a branch at a time without taking the whole setup down for a day.The customer has a Unix based dumb-terminal application running on a server at headoffice that they access from their branches using terminal emulators on Windows PCs and thin client hardware devices that support vt100 terminal emulation.
Prior to installing the Cisco RV042's everything was working fine. Now they are using the RV042's they keep getting the sessions from their branches dropped. Both PC users and thin client users are losing sessions and it happens with active and idle sessions. I have checked the logs on the routers when users are disconnected and there is nothing logged at that time (other than my login)... I had thought maybe it was to do with tunnel renegotioations so I have set to phase 1 / phase 2 SA timeouts to 86400 & 28800 seconds respectively but this has had no effect. I had also seen somebody advised disabling 'SPI' in the firewall... I have tried this and it makes no difference.
Cisco Routers :: Possible To Telnet Into WRVS4400N Wireless-N Gigabit Security With VPN
Jun 18, 2012Is it possible to telnet into the 'WRVS4400N Wireless-N Gigabit Security Router with VPN' router? When I try it says the remote system refused the connection.
View 5 Replies View Related1723 Open On Routers But Can't Telnet From Internet Address?
Feb 1, 2011I have small business server 2003 setup as a DC and did not install exchange, i use hosted exchange. i am trying to setup vpn and have opened port 1723 on both of my router. my network routes through a wireless router(192.168.1.1) (port 1723 forwarded to .1.104) to a second wireless router (192.168.2.1) to my server with two nic cards (.2.2 - external and .2.103 - internal) (port 1723 forwarded to .2.2) i can telnet 192.168.2.2 1723, .2.103, .1.104 - my ip of my second router handed by the first router. my server in handling dhcp and it is disabled on my .2 router. I CAN NOT telnet my public ip handed to 1.1 from the ISP(my internet IP). it tries for about 30 secs and dies.
View 8 Replies View RelatedCisco Routers :: RV016 Firewall Policies Via Telnet (rules / Chains / Etc)
Nov 3, 2011I am having some troubles finding information about how to configure firewall policies (rules, chains, etc.) via telnet on a RV016. The reason for that is that i keep getting some log entries "connection refused - policy violation" and "blocked" even with my firewall wide open (only allow rules on all interfaces, SPI and block wan request disabled, multicast and https enabled, etc.... ). Also, with these exact same rules, i can only connect via PPTP with the firewall disabled. The minute i tick the enable option the tunnel never gets to authentication phase. I then started reading OpenRG manual and many things are quite similar, but some other entries are missing from that manual (maybe some changes made by cisco?). I am trying to figure out some service ids, chains (e.g. the rv016 has some rules redirecting to chains 10, 100, 200 but i can not find them anywhere), and so on. I have only one rv016 and about 60 connections to it so i can not experiment that much without having the whole company on my neck with internet problems.
View 2 Replies View RelatedCisco Routers :: Auto / Programmatic UPnP Port Forwarding For RV042 And E4200 Routers
Jan 24, 2013I have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
Cisco Routers :: RV042 / RV042G / Small Business Routers With Inter-VLAN Capability
Aug 22, 2012I was looking for a small business router that has VPN support and dual WAN support for load balancing. Upon reading reviews, I think RV042/RV042G is a good choice. Now am thinking if it supports intervlan/ router-on-a-stick configuration?
View 5 Replies View RelatedLinksys Wired Router :: Cisco RV042 With Two Subnets For A Web Server?
Dec 21, 2011I have a static DSL connection and my ISP is giving me 4 static IP's. I have connected my RV042 to the DSL modem and I have now 1 subnet at 192.168.0.0. What I want to create is a WEB server/ Email server, but to sit on a different subnet - 192.168.5.0. For now I have connected the server to the DMZ port, but I am unable to to access it from WAN, only from LAN. how to configure properly the 2 subnets (192.168.0.0 and 192.168.5.0) and how to forward my static address to the server which I which to be on the 192.168.5.0.
View 1 Replies View RelatedLinksys Wired Router :: Configure Cisco RV042 To Access PPTP VPN Server?
Jun 7, 2012how i can configure the Cisco RV042 to access PPTP VPN Server (Witopia VPn) or other vpn servers.
View 1 Replies View RelatedCisco Routers :: RV042 Won't Get Second IP
Feb 27, 2012I have two Internet connections-
1-DSL Modem (WAN1-Internet Port)
2-Cable Modem-Comcast (WAN2-DMZ/Internet Port)
I connected the DSL (WAN1-Internet) port in and the Cisco RV042 was able to get an IP automatically. I tested the connection and it works just fine. Then I connect the Cable Modem-Comcast (WAN2-DMZ/Internet Port) in and I have the RV042 automatically optain IP address. But it just says 0.0.0.0. I've tried release/renew and that does nothing. Also, when I connect the 2nd Internet connection the Internet goes down. The only way it goes back up is when I disable under the PORT MANAGMENT setting.
All the settings have been kept to the default.How can I get the router to obtain an IP address from the Cable Modem-Comcast (WAN2 DMZ/Internet Port).
Cisco Routers :: NAT Over VPN On RV042
Mar 6, 2012We have an Cisco RV042. We need to setup a VPN with a business partner who is already using our current IP scheme on another VPN with another client. They have asked us to NAT our IP's from 192.168.25.x to 192.168.245.x
I can't seem to figure this out on this router. I have done it on a Sonicwall and Watchguard, but can't seem to get it to work on the RV042.
I have setup the VPN and the One-To-One NAT. The tunnel will connect (using the 245.x IP as our local IP on the VPN setup), but no traffic will pass through.
Cisco Routers :: Rv042 Configuration With Vpn?
May 20, 2012i was planed to make a vpn over rv042 so i get the rv042 connected behind a thosmon 456(configured as a bridge) and 1 static ip ... and i configured the vpn and worked great ...but due to some circumstance i get a package of 6 ips insted of the old ip , so when i try to configure the router with the ISP they but the wan ip 10.232.x.x and told me that an internal ip from there lan ... and give me the 6 ip of 196.x.x.x to use as 1 for internal interface for the rv042 and 5 for the pc's,now the vpn not working anymore...notice: when try to configure the vpn tunnle in the local securty setting i mark the ip only and the ip that abear is the wan ip 10.232.x.x but i can't ping that ip beside i can ping the internal ip of the router 196.x.x.50does rv042 can support static and virtual ip inside the lan |! can i configure the thomson as pppoe and use one static ip from 196.x.x.x as wan ip for it ... and use anther 196.x.x.x ip for the rv042 to get access from outside and connect the lan to the rv042 with internal ip 192.168.x.x ...so i can access the vpn from outside .....and can connect the device i need to use static ip to the thomson ...
View 0 Replies View RelatedCisco Routers :: RV042 - Bug Found In VPN?
Sep 23, 2011Firmware v4.0.4.02 has a nasty bug in the VPN section. If you switch to "IP by DNS Resolved" (yes, it says "Resolved" instead of "Resolution". Gotta love all the Engrish in the RV042!), it will automatically populate the field with "@yourdomain.com". This will cause the VPN to not lookup the proper IP address. Simply deleting the atmark after it populates will fix the problem.
Let's see what happens when we validate a Cisco RV042 webpage:
Errors found while checking this document as HTML 4.01 Transitional!
Result: 353 Errors, 1 warning(s)
Don't even get me started on the horrible Javascript...
Cisco Routers :: RV042 To ASA VPN Not Coming Up?
Apr 24, 2013i am trying to make a simple Site to SiteVPN between two offices, one has Cisco ASA and one has RV042 router.when traffic initiated from ASA side, i keep getting this message in Debug and tunnel wont come up
.
[IKEv1]: Group = A.A.A.139, IP = A.A.A.139, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.Apr 26 00:15:53 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
whereas if traffic initiated from RV042 side, i keep getting this message in debug and tunnel wont come up.
Apr 26 00:43:44 [IKEv1 DEBUG]: IP = RV.RV.RV.139, Oakley proposal is acceptableApr 26 00:43:44 [IKEv1 DEBUG]: IP = RV.RV.RV.139, IKE SA Proposal # 1, Transform # 0 acceptable Matches global IKE entry # 6Apr 26 00:43:44 [IKEv1]: IP = RV.RV.RV.139, Connection landed on tunnel_group RV.RV.RV.139Apr 26 00:43:45 [IKEv1]: IP = RV.RV.RV.139, Connection landed on tunnel_group RV.RV.RV.139Apr 26 00:43:45 [IKEv1]: Group = RV.RV.RV.139, IP = RV.RV.RV.139, Freeing previously allocated memory for authorization-dn-attributesApr 26 00:43:45 [IKEv1]: Group = RV.RV.RV.139, IP = RV.RV.RV.139, PHASE 1 COMPLETEDApr 26 00:43:45 [IKEv1]: IP =RV.RV.RV.139, Keep-alive type for this connection: DPDApr 26 00:43:45 [IKEv1 DEBUG]: Group =
[code].....
Cisco Routers :: Enabling 6rd On RV042?
Sep 27, 2012Apparently one of my two ISPs,CenturyLink, supports 6rd connections to IPv6.
This is supported natively on my Q1000 ActionTec modem, however my modem is in "transparent bridging" mode, so that the RV042 v3 can be the only router.
how to configure the RV042 to operate in this manner.
Per the CenturyLink FAQ: the IPv6 address space is:
2602::0 /24
Most importantly, can I do this WITHOUT buying a new modem.
